Search Documents

By N. J. Grant, D. S. Bloom

An investigation of the Cr-Mo-Ni ternary system and attendant binaries has been completed. Some changes in the binary diagrams are shown to be necessary. The 1250°C section of the ternary and the liquidus surface have been delineated. A system of invariant reactions existing above 1250°C has been suggested. BECAUSE chromium, molybdenum, and nickel are important not only as bases for alloying systems but also as major alloying additions for other refractory metals, a study of the phase diagrams is of great interest and importance. In addition there are interesting features of theoretical value, a number of which are of prime consideration in this work. The major aim was to determine the ternary phase diagram of these metals at and above 1250°C, with sufficient attention given to lower temperatures to permit an understanding of the conditions existing at 1250°C and above. To understand ternary systems it is essential that accurate information concerning the binary systems be available, which in turn presupposes thorough knowledge of the constituent elements. On the basis of this investigation not only were significant inaccuracies indicated in the binary systems but much consideration had to be given to one of the elements, that is, chromium. The observation has been made that chromium undergoes a crystal transformation at a temperature near its melting point. Much of the experimental data leading to the detection of this transformation and the effects of this hypothesis on the form of the Cr-Ni phase diagram have already been reported' . and will not be repeated here. The experimental methods employed in the investigation have also been covered.'-" he purity of the molybdenum utilized in this work showed by qualitative spectrographic analysis that chromium, copper, iron, silicon, and tungsten were present in quantities of 0.1 to 0.001 wt pct. During the course of the investigation more than 100 melts were made, weighing from 150 to 200 grams each. Each of these melts was sectioned for chemical analysis and for specimens for examination in the as-cast and various heat-treated conditions by X-ray and metallographic means. All X-ray diffraction patterns reproduced here were made using chromium Ka radiation although iron and copper targets were used on occasions during the investigation. Experimental Results Mo-Ni-System: The most recent comprehensive investigation of the Mo-Ni system was made by Ellinger' in 1942; the diagram as shown in the American Society for Metals Handbook is based on his work. The work done on the system in this investigation substantiated the general form of the diagram although some differences were observed. These are indicated by a comparison of Ellinger's diagram and Fig. 1, the latter showing the results of pertinent thermal analyses made in this research. It can be seen in Fig. 1 that the eutectic composition is

Jan 1, 1955

By Schlumberger, C

IN the search for practical geological problems amenable to solution by the potential methods, the geophysicist is led to study mathematically various theoretical cases. In these idealistic discussions, the media under consideration are generally supposed to be homogeneous and iso-tropic. The geophysicist, of course, realizes perfectly that these condi-tions do not occur in their entirety in reality. However, the assumptions made are justified, because very often they are necessary in order to render possible an exhaustive study of a given problem, which otherwise would be too complicated, and would not lend itself to a complete mathe-matical analysis. Of the above two assumptions, that concerning the homogeneity of a given geological formation is satisfactorily realized except in so far as isotropy is concerned, since this property is not often encountered in practice. As a consequence, it is very desirable for the geophysicist to have quite an extensive knowledge of the properties of anisotropic forma-tions, and of the laws that govern the propagation of electric current therein. With such principles in mind, he will be able to decide whether the conclusions arrived at in simple, isotropic conditions are still correct in more complex cases, or in what way they must be modified or adapted in order to constitute a sound basis for the interpretation of the results obtained in anisotropic media. On the other hand, the fact that in anisotropic formations themobility of the ions is greater along the strike than perpendicular thereto can be utilized for determining the direction of the dip by induc-tion measurements. We therefore propose to study in three successive chapters the following points: 1. Propagation of the electric current in anisotropic media. 2. Some consequences of the anisotropy of geological formations with reference to the surface electrical measurements, and their interpretation. 3. Determination of the direction of the dip of anisotropic formations by surface induction measurements.

Jan 1, 1933

By C. H. Li, R. J. Stokes, S. H. Bendel, J. A. Sartell, T. L. Johnston

The mechanism of the oxidation of high-purity copper has been studied at temperatures from 500° to 981°C employing gravimetric, high-temperature microscopic and inert marker techniques. An investigation of the adhesion of copper oxides was also made. The oxidation of copper is found to be parabolic at all temperatures. It is concluded that the controlling mechanism is the outward diffusion of CU+ ions through the Cu2O layer, but the mechanism of diffusion is modified by the state of compressive stress in the oxide layer at the oxidation temperature. At temperatures below the transition from elastic to plastic behavior of Cu2O the growth stresses reach a value sufficiently high to cause CuO whiskers to be extruded. The extrusion of whiskers results in the injection of a large number of vacancies into the CuO. The Cu20 layer grows by the advance of the CuzO/CuO interface into vacancy-rich CuO. Since there is an adequate supply of non -thermally created vacancies, the activation energy for oxidation is that required to move the Cu+ ion through the appropriate saddle point to a neighboring vacancy, which has been determined to be 20,000 cal per mole. At temperatures at which the Cu20 can deform plastically the stresses are never high enough to cause whiskers to form. thus vacancies must be supplied by themal activation and as a result the activation energy increases to 40.000 cal per mole. ALTHOUGH extensive studies of the oxidation kinetics of pure copper have been made in the past. the mechanism has received relatively little attention. As a result, certain features of the kinetic data have not been satisfactorily explained' For example, several workers1,2 have reported that the activation energy for oxidation in the range from 500° to 700° C was about 20,000 cal per mole whereas that above

Jan 1, 1960

By George Stanley Scott

Many requests for information as to the possibility of washing coals to some predetermined percentage of ash or sulfur have suggested that the producers aim to satisfy some degree of purity set by the user of the fuel, rather than to attain the greatest economic benefit to all concerned. This paper is written to show that the highest economic purity of washed coal can be determined from washability studies of the raw coal, costs of mining and washing coal, and data on the effect of ash and sulfur on the value of the coal for the particular use for which it is intended. Coke fob Blast-fuenace Use For purposes of illustration, we take the case of coal washed for coke to be used in the iron blast furnace. The method outlined can be made general in its application by substituting for the figures used here the actual operating figures for the particular case under consideration. In general, it costs the blast-furnace operation from 8 to 25 c. per ton of pig iron to slag out each 1 per cent. of ash introduced into the blast furnace by the coke. This figure depends on which one per cent. of ash is removed, and decreases with decrease in ash. When blast furnaces and coal mines are considered as a whole, the figure decreases to zero and then becomes negative, on account of low recovery of washed coal. Various figures1 have been given by different investigators. These figures necessarily differ, not only on account of the differences in operating costs but on account of the difference in the respective fuels as well. For the purpose of this paper, which, as explained, is to point out a method of attacking a certain problem, the figures used in the exposition of the method are of secondary importance. It is apparent that no universally applicable figures can be used, because there are none. Each plant has its own coal,2 its own operating cost, and its own conditions.

Jan 1, 1930

By G. C. Gould

The nature of freckle segregation is determined by chemical analyses, microradiograplzy, and electron microprobe. In addition, the influence of chemistry variation on freckle formation is studied in laboratory experiments. It is demonstrated that controlled laboratory solidification can produce freckle segregation. "FRECKLE" segregation is a discontinuous, rod-like segregation observed in vacuum consumable -electrode ingots. Figs. 1 and 2 show this segregation as pencil-like, dark etching areas of segregation found in longitudinally and transversely sectioned consumable-electrode ingots. In most cases the segregation is perpendicular with respect to gravity and parallel to the longitudinal axis of the ingot. The segregation is most often encountered at or around midradius in large vacuum consumable-electrode ingots. The austenitic alloys, A-286* and 718, † have shown particular susceptibility to this mode of segregation. The origin of these rodlike pockets of segregation is not well-understood. It has been suggested that the segregation is a result of a portion of the electrode dropping off and passing through the arc un-melted. On the other hand, smeltzer1 has demonstrated the freckle segregation in A-286 to be comprised of low-melting constituents relative to the matrix melting point. The discontinuous nature of the segregation is the most perplexing facet of the freckle-segregation problem. It was to gain some insight into this part of the problem that this work was undertaken. I) PROCEDURE At the outset of the work identification of the phases present and the elements concentrated in the freckle areas was undertaken. The electron micro-probe was used to determine general enrichment as well as -specific phase chemistry. Microradiography using cobalt and chromium radiation was also used on the freckle areas again to determine the elements involved in the segregation. X-ray diffraction patterns were made from portions of these same foil specimens. Optical microscopy and Knoop hardness measurements were also used

Jan 1, 1965

AMONG the fellow prospectors of Black Jack Newman, locator of the claims that became the Miami mine, were J. D. Coplen and Bud Woodson. Woodson was in the district when the Bloody Tanks Indian massacre occurred, near the present town of Miami. He was a prospector long before Jack Newman worked in a mine, and for years he had done assessment work on some of the claims that Coplen acquired for his Inspiration company. Woodson recalls that a Scotch geologist from Morenci once visited his claims; and that the geologist tried to get the Phelps Dodge company interested in the property, but without success. Coplen interested some people in Kansas City in his claims that lay west of Newman's. He induced them to organize the Inspiration Mining Co., and by 1908 this company controlled 23 claims, which had been prospected in desultory fashion by a series of adits. One of these, near the Keystone property, encountered some lean copper-bearing rock, but later development failed to disclose any substantial quantity of ore at this particular point. Coplen, as general manager, in September, 1908, was negotiating with several exploration companies which at the time were on the lookout for low-grade copper properties. As a matter of fact, when J. Parke Channing visited Globe, in December, 1906, F. C. Alsdorf showed him the Inspiration claims as well as Newman's. Channing evinced little interest in an option on Inspiration because he could get so much better terms from Newman. He decided to concentrate his work on the Newman claims, with the idea that if he were successful in developing ore, he could later get Inspiration on terms at least equally good. Subsequently, the United States Smelting & Refining Co., which has since added "Mining" to its corporate name, took an option on Inspiration.

Jan 1, 1933

By W. Seymour

Uranium was cold rolled to a reduction in thickness of 90 pct and the preferred orientation of the grains was determined from X-ray intensity data. Complete pole figures for a large number of atom planes were plotted, and the preferred orientation was found to be duplex (102) [0101 + (012) [021]. These preferred orientations are compared with those reported for many of the hexagonal-close-packed metals. THE preferred orientation of a highly reduced cold-rolled uranium strip was determined in order to obtain additional experimental data which would be useful in further understanding the deformation mechanisms of uranium. The preferred orientations reported herein are not in agreement with those theoretically predicted by Calnan and Clews' for cold-rolled uranium sheets, and differ somewhat from those reported from experiments by Fisher, and Burke and Turkalo. Such variations might be accounted for by differences in the fabrication temperature and the reductions. Experimental Procedure The uranium used in this investigation had been hot rolled to 0.060 in. at 575°C from 0.393 in., and from a 0.060 to 0.020 in. thick sheet at 275°C. From this point the sheet was cold reduced 90 pct to 0.002 in. at room temperature. Three specimens were used to obtain complete pole-figure data. The first was a 1/2 in. square section illuminated by the X-ray beam on the rolling surface. The other two were l/2 in. square longitudinal and transverse sections each made as follows: Approximately 200 1/2 in. square sections of the foil were piled one on top of the other, so that the rolling direction for each piece was kept coincident. A 1/2 in. square by 1/8 in. thick steel section was placed on the top and bottom of a pile and the entire assembly was then bolted tightly together through a 1/8 in. diam hole drilled down through the center. Each pile was then surface-ground from the two proper sides to sections 1/2 in. square by 3/16 in. thick. These specimens were then polished flat and electro-polished to remove 0.005 in. of the surfaces to be examined. It can be shown that uranium is so opaque to a Cu Ka X-ray beam that only a small percentage would be transmitted by one micron of uranium. Therefore, a method of measuring the X-ray intensities diffracted from specimen surfaces was used. The specimens were mounted in a modified Schulz reflection holder' which automatically changed the position of the specimen at a constant rate. The holder, in turn, was mounted on a General Electric XRD-3 Spectro-Goniometer and an automatic record made of the diffracted X-ray intensity vs specimen position. While a specimen moved automatically through 10" inclination, at a rate of l° per min, it simultaneously rotated 360" about a normal to the illuminated surface. (The inclination and rotation angles are referred to as F and a, respectively.) The data were then plotted along the resulting spiral path on a stereographic projection, Fig. 1. Because of defocusing effects on the diffracted beam which occur when diffracting surfaces are in-

Jan 1, 1955

By Blake M. Caldwell, Harrold D. Owen

The continued use of permanent-type, we11 completion Iras pointed LIP the need for more powerful through-tubing perforating equipment. A new expendable shaped charge perforator has been developed in which the charges are run through the tubing in a vertical position and then opened out to a horizontal position when at the desired shooting zone. The performance of this new tool is comparable to that of conventional casing type perforators. This paper describes the new tool and its applications. Performance data in targets rind under various actual well conditions are presented. INTRODUCTION The general acceptance and increasing use of pernianent-type well completion by the oil industry has indicated the need for through-tubing perforating equipment with performance comparable to that of conventional casing type perforators.'.' To achieve the performance desired, a new, expendable, shaped charge perforator has been developed with adequate power for effectively perforating both 51/2-in. and 7-in. casing below tubing. This has been accomplished without resulting severe damage to the casing and can he obtained under extremes of pressure and temperature. The design of this new tool is a radical departure from previous concepts of tubing guns since it was felt that the two major limitations imposed by previous designs severely handicapped performance. The first of these limitations was the restriction imposed upon the length of the charges by the necessary small inside diameter of the carrier. This resulted from the necessity for compromises in designing a hermetically sealed gun small enough to allow free passage through 2-in. tubing, yet with sufficient wall thickness to withstand some minimum pressure. In an effort to overcome this limitation, the charges were in some cases placed at an angle with the axis of the well with resulting loss in effective depth of penetration. The second limitation concerned the extreme distance of the charges from the casing when the gun was fired. An example of the latter situation is demonstrated by the fact that a conventional 13/4-in. tubing gun centralized in 51/2-in., 17-lb casing has a clearance of more than 1-9/16-in. on all sides. This means that a considerable portion of the force from each charge must be expended in penetrating this 1-9/16-in. of well fluid before it even reaches the casing. With the gun centered in 7-in., 23-lb casing, the amount of fluid penetration required of each jet is in excess of 21/4-in. In a situation where the 13/4-in. gun is touching one side of the 51/2-in., 17-lb casing, the jets from the charges on the opposite side have more than 3%-in. of fluid to penetrate. A similar situation in 7-in., 23-lb casing necessitates the penetration of more than 4-9/16-in. of fluid. The penetrating effect of the charges is severely impaired in passing through so much fluid. Under such conditions, there is usually insufficient force left to penetrate the casing. Previous studies have shown the decided disadvantage of having to shoot through such an excessive quantity of well fluid.'.' The problem. then, was how to position large powerful charges close to the casing prior to firing and still manage free passage through 2-in, tubing. The solution appeared to be in some method of folding sealed charge units in an open type, expendable. 13/4-in. carrier for travel through the tubing, and unfolding them upon their arrival at the shooting zone in the casing. It was desired to control the mechanism electrically from the surface through the regular shooting cable, making the release of the charges independent of the physical characteristics of the well, yet with a provision to prevent the gun from firing until the

Jan 1, 1955

By I. F. Jackson, H. L. Hartman

Hard-metal inserts have received considerable attention in the mining industry recently for a variety of excavating and penetrating purposes. Their use in percussive drilling and in coal cutting machines is well known, but attempts to utilize them in cutting materials such as dimension stone have been discouraging because of excessive tool wear and failure. Particular attention is given to those properties of hard-metal inserts that affect their resistance to wear. A consideration of the actual wear mechanism shows the importance of correct mounting of the inserts and of the selection of suitably powered driving motor so as to achieve minimum tool wear and maximum tool life. Comparisons are made between the performances of types of hard-metal inserts, relating their inherent properties with results obtained in laboratory tests. As part of a broad program to improve the quarrying and processing of industrial minerals, The Pennsylvania State University has been investigating the machinability of slate under laboratory and field conditions. It should be emphasized that the results of the research presented in this paper are also applicable to other natural structural materials, and particularly to the more workable ones such as limestone and sandstone. Improvements which accrue in cutting and sawing should prove of benefit to all the dimension stone industry. Further, it may be pointed out that the results reported here are applicable to rotary drilling (with drag bits) as well as to cutting and sawing of rock. INVESTIGATIONS IN RELATED FIELDS The investigation was initiated with an extensive survey of available literature related to metal cutting and to rotary drilling. The following similar features between metal cutting and slate cutting became evident: 1) Hard-metal inserts are widely used as a cutting tool in both cases. 2) The forces acting on the tool may be resolved into normal and tangential components. 3) Rate of penetration and tool wear are important criteria in each case. On the other hand, important differences also exist: 1) Most metals, exhibit plastic behavior, while slate (and most rock) is a brittle material under normal conditions. 2) In metal cutting the component of force acting parallel to the surface of the workpiece is considerably greater than the force holding the tool against the workpiece. 111 slate cutting, this situation is reversed. Similarities between drag-bit rotary drilling and slate cutting are as follows: 1) In both casts, a tool, usually of the hard-metal insert type, is used to penetrate a brittle material. 2) The drilling forces and related variables, such as rotation speed, are similar. 3) Chip formation in each case is essentially the same. 4) The shape of the tool is similar in rotary drilling and slate cutting. Important differences are also apparent: 1) The objective of drilling is to produce a directed hole, while in cutting it is to form a kerf. In core drilling, however, a kerf is also produced. 2) The horizonta1 component of force in rotary drilling decreases from the center to the outside of the tool, whereas in slate cutting the component is almost uniformly distributed across the width of the tool. 3) The power absorbed in the drill rod is greater in rotary drilling. 4) The clogging action of chips, if excessive power is applied to the tool and if flushing is insufficient, is more serious in rotary drilling. Because of the striking similarities between metal cutting and slate cutting, and between rotary drilling and slate cutting, it was considered that the findings of investigators in those fields would serve as a guide for experimental studies of slate cutting. The following is thus devoted to a discussion of those aspects of metal cutting and rotary drilling pertinent to the present investigations.

Jan 1, 1962

By G. R. Love, M. L. Picklesimer

Aboue 950°C the Nb-Zr system consists of a completely miscible bcc solid solution, commonly called the phase. Between 950 and 600°C, and between 20 and 85 pct Nb, the phase deconlposes, after sunciently long times, into two bcc solid solutions. The pct Zr alloys are conveniently descibecl with T-T-T (time-temperature-transformation) curves having a nose at about 2 hr at 700°C. The reaction rate varies only slowly with zirconium content and negligibly with oxygen contanzination; it is speeded up by a factor of 10 to 15 by 90 pct cold ulork and slowed dou by n factor oj 10 to 30 by a two-hundrecljold increase in grain size. Nb-r alloys with compositions between 40 and 85 pct Nb have been the basis for the majority of commercially important superconducting materials. In part because of their commercial promise, more is known about these alloys than about most other high-field superconducting materials. At the same time, there is considerable disputed or incomplete metallurgical information. For example, although Rogers and tkins&apos; indicate a monotectoid reaction at approximately 600°C and a two-phase 01 + 0, field extending between 20 and 85 pct Nb and to a maximum of 95OGC, erhout&apos; has reported that this entire region would be a single homogeneous B were it not for oxygen contamination. Again, although it has been shown that relatively short-time heat treatments in the vicinity of 700CZ significantly improve the ability of short wire samples to carry high currents in high magnetic fields at 4.2K, these observations have never been fully correlated with the structural change or changes occurring during the anneal. We intend to investigate in detail the effect of metallurgical variables, including heat treatment, on the superconducting properties of hard superconductors. To verify that our experimental techniques are valid and to establish a relative standard against which other materials may be measured, we feel it advisable to know the behavior of the Nb-Zr alloys under a variety of processing conditions. As an initial step toward this goal, we have determined in detail the kinetics of the transformations in Nb-Zr alloys. EXPERIMENT A number of problems had to be solved before beginning any fruitful work on the reaction kinetics in this system. While solving some of these problems, either by chance or by design, small amounts of information were obtained about alloys containing 40, 50, 60, 65, 67, 70, and 75 pct Nb, bal. Zr. In addition, a large range of grain sizes and a range of temperatures considerably greater than the range indicated by Rogers and Atkins phase diagram were examined. We will, however, report in detail only the results obtained for the Nb + 33 pct Zr and Nb + 25 pct Zr alloys at three grain sizes, two levels of oxygen contamination, and the temperature range 550 to 950°C. These data are most complete, but the other data are sufficiently complete to indicate the kind and magnitude of the variation of the transformation kinetics outside this range. The first and most difficult problem encountered in this inquiry was one of sample homogeneity. When Nb-Zr alloys are arc- or electron-beam-melted on a cooled copper hearth, solidification is sufficiently slow that there is appreciable coring in the cast structure and a large variation of grain size across the button thickness. Both these factors significantly affect the apparent reaction rate in the system. A two-step solution to the problem was attempted; an arc-melting and drop-casting technique has been developed by conald that greatly reduces the as-cast grain size and virtually eliminates coring segregation. Ingots made in this way exhibited no detectable (3 pct maximum) zirconium segregation. Before it was evident just how good this technique was, we attempted to supplement it with rather long-time, high-temperature annealing of the cast ingots. This annealing was carried out in evacuated and sealed (seal-off pressures < 1.0 x 106 torr) quartz capsules lined with tantalum foil at 1400 to 1450 C for 8 to 72 hr. There were two principal effects of this treatment: the grain size increased to a fairly uniform 150 p, and the surface and all grain boundaries near the surface acquired a film of a second phase, tentatively identified as an oxide (possibly additionally contaminated with silicon). There was no evidence that this 1400 C treatment had affected the zirconium segregation. High-temperature annealing was subsequently used only for grain-size control, but anneals of longer than 4 hr at temperatures greater than 1000°C were performed in dynamic vacuums (pressure no greater than 1.0 x lo torr). Any contamination resulting from these treatments was well below the limits of detection of our techniques. All samples, as cast, were cold-swaged to at least 85 pct reduction in area. The samples called cold-worked were tested as swaged. The minimum re-crystallization anneal for these alloys was about 12 hr at 1050 C; this produced an equiaxed grain diameter of about 4 to 8 P. Annealing for 4 hr at 1450°C produced a grain size of about 80 to 150 p; and annealing for 4 hr at 1650aC, close to the melting point of many of these alloys, produced a grain size of 0.5 to 1.0 mm. At all temperatures, the larger grain size was

Jan 1, 1967

By Jacob T. Wainwright

AS a means for increasing the efficiency in modern blast-furnaces by supplying to them blast of a much higher temperature than is now possible, the writer offers as a suggestion a modification in the construction of regenerative hot-blast stoves. Stated briefly, the plan proposed is to pre-heat both the gas and the air for its combustion in a manner similar to that generally adopted in Siemens openhearth furnaces. After thus carrying the temperature of the stove to a point much higher than that common in hot-hlast stoves, the cold blast passes through it. Without entering into the details relating to the reversing valves and the system of flues, the general plan may be outlined as follows, referring to the accompanying drawings: The valves are so placed in heating up the stove that the blast-furnace gas enters at B, Fig. 1, and the cold air for combustion at A. Ascending in flues, F and E, respectively, combustible gas and air meet and mix in the combustion-chamber, I. Flowing through K, they descend through the flues, G and H, escaping through the chimney. In this manner the walls of the combustion. chambers, I and L, are highly heated, and the right-hand side of the stove is carried to a higher temperature. By reversing the valves, blast-furnace gas enters at C and cold air for combustion at D. Both are pre-heated in their ascent through the flues, G and H. They burn in the combustion-chamber, L, and the hot gases of combustion, flowing through K, I, E and F to A and B, heat the left-hand side of the stove. In this manner the stove is carried to a temperature greater than that of those now generally in use, in which air and gas are burned without preliminary pre-heating. In the plan proposed, that side of the stove will, of course, be relatively cooler through which cold air and furnace-gas last passed in its ascent to its combustion-chamber. After having sufficiently heated the stove in the manner outlined, the cold blast is admitted through all the flues, A, B, C and D. It ascends through the highly-heated regenerative material to the chambers at the top and descends through the flue, P, Fig. 2 (dotted

Jan 1, 1889

By Lester L. Hirst, Arno C. Fieldner, Henry H. Storch

EXPERIMENTAL work on liquefaction of coal was taken up by the Bureau of Mines in 1936 when it became evident that a prudent policy from the national point of view should include preparation for the time when gradual exhaustion of petroleum resources would require supplementing the growing demand for motor fuel with gasoline and diesel oil from coal. At that time (1936) certain foreign nations that had no home sources of petroleum, especially Germany, England, and Japan, were conducting active research and at least two of them were producing liquid fuel from coal on a commercial scale. Germany was reported to have an annual producing capacity of 800,000 metric tons of gasoline per year, and England had just put into operation the Billingham plant of Imperial Chemical Industries for the hydrogenation of bituminous coal and tar by the Bergius-.I.G. process. The annual capacity of this plant was about 150,000 long tons of gasoline per annum (3500 bbl. per day). With these developments taking place in foreign countries, it seemed important to undertake a long-range program of fundamental research in this country to establish a sound groundwork for the evaluation of foreign work on synthetic liquid fuels and at the same time to obtain data on the oil yields and operating difficulties using various kinds of American coals and lignite to the hydrogenation process. The results of such research would be useful in determining the yields and quality of liquid products obtainable from various coals so that American industry would be in position to select the most suitable coals and make rapid progress in establishing this new industry when the commercial need should arise. It was hoped, also, that progress in a better understanding of the chemistry of coal hydrogenation would reduce the cost of the process materially. To carry out this program, a small continuous unit capable of hydrogenating 100 lb. of coal in 24 hr. was installed at the Central Experiment Station of the Bureau of Mines at Pittsburgh, Pa. Small steel autoclaves or bombs of 0.3 gal. (1.2 liters) capacity also were used for batch-hydrogenation experiments in the study of the chemical fundamentals of the process. Much valuable assistance was obtained in planning the experimental program and designing the equipment from the Fuel Research Station of Great Britain and the Fuel Laboratories of the Mines Department of Canada, where such investigations had been in progress for several years. EQUIPMENT AND GENERAL PROCEDURE OF RESEARCH The industrial liquefaction of coal by the Bergius-I.G. hydrogenation process as practiced at Billingham, England, from

Jan 1, 1944

By R. W. Heckel, H. W. Paxton

The growth of grain boundary films and Widmanstiitten plates of proeutectoid cementite in hypereutectoid steels ulas considered quantitatively in three plain carbon steels and one "pure" iron-carbon alloy. Growth was found to take place at a slower rate than would be predicted on the basis of a model invoking rate control by long range diffusion of carbon. The films in the pure alloy grew faster than those in the plain carbon steels. A possible explanation is suggested. In 1904, Nernsst&apos; and Brunner2 postulated that ionic crystals growing in supersaturated aqueous solutions grew at rates determined by diffusion through the solution to the growing crystal interface. The gradient down which the diffusion took place was assumed to be fixed by the supersaturated bulk solution concentration, the concentration dt the crystal surface and some arbitrary distance. The flux of material to the crystal was described as Flux where D is the diffusion coefficient, A the crystal surface area, Ci the bulk solution concentration, Co the saturated solution concentration, and 6 the thickness of the diffusion zone. It is obvious that the expression is an adaptation of F+ick&apos;s3 first law of diffusion (steady state). This was the initial formulation of what will be defined here as "diffusion controlled growth," i.e., growth limited by the long range diffusion of a component either to or from the advancing interface assuming both phases at the interface to be in equilibrium. This idea of equilibrium interface concentration implies an infinite reaction rate at the interface. Volmer, Zener,&apos; and 11schner6 have derived expressions for the diffusion controlled growth of spherical precipitates in metallic systems. These analyses agree that the growth in a given direction should be parabolic with time. Brown and Hawkes7 observed that graphite, formed both from the decomposition of cementite and from the decomposition of eutectoid austenite in cast irons, grew according to a parabolic relationship and, therefore, concluded that the laws of diffusion controlled growth, as defined above, were obeyed. They, among others, failed to consider, however, that parabolic growth is a necessary, but not sufficient, condition for diffusion controlled growth. Mehl and Dube"&apos; have pointed out that equilibrium may not be realized because the concentration at the interface cannot change instantaneously from that of the bulk to the saturation value. Furthermore, they propose that an equilibrium solute concentration in the parent phase adjacent to the precipitate would remove the thermodynamic activity gradient across the interface and, thus, stop the growth process. Frisch" has also emphasized the importance of interface concentrations that vary throughout the growth of a new phase. The variation in activity across an interface, as discussed by Onol&apos; and Cahn and Hilliard,12 is of fundamental importance to this question. Ham13 considered the data of Turnbull14 on the growth of barium sulfate in aqueous solutions. He concluded that the data could be analyzed in terms of a radiation-type boundary condition. Flux across interface = K (c, - C,) [21 where C, is the concentration in the solution at the interface, Co the saturated solution concentration, and K the proportionality constant. The edgewise growth of Widmanstlitten plates, frequently referred to as the rate of lengthening, was first considered by Zener.&apos;&apos; Basing a mathematical analysis on steady-state (constant velocity) growth he concluded that where G is the growth rate, D the solute diffusivity, Ci the concentration in the bulk, Co the equilibrium interface concentration, C, the concentration in the precipitate, a a constant, Y the radius of curvature of the edge of the plate, and rC the critical radius, i.e., the radius which would increase the activity of solute at the interface at equilibrium under the influence of capillarity to that of the bulk. Zener1&apos;

Jan 1, 1961

By W. O. Brown

A laboratory investigation was conducted to determine quantitatively the extent to which connate water was contacted and displaced by invading flood water. In these experiments the connate water in unconsoli-dated sand packed columns was completely displaced by injecting water. The nature of this displacement was similar to that previously described for single-phase miscible fluid displacement studies, and thus the presence of a non-wetting immiscible phase did not appreciably change the nature of the displacement. The effects of water injection rate, column length, and oil viscosity on connate water displacement were investi-gated. It is concluded that the connate water in a reservoir is the water which actually displaces oil from the pores of the rock during a water flood. During a water flood the connate water forms a zone which separates the invading flood water from the continuous oil phase. The size and shape of connate water bank is chiefly dependent oil the oil viscosity and the column length. INTRODUCTION Water flooding is one of the most widely used techniques for the secondary recovery of oil. Presently, however, it is still not possible to recover all the oil in a reservoir by water flooding. The research described in this paper was conducted as part of a study to determine the conditions under which 100 per cent oil recovery could be attained by water flooding. The particular objective of this work was to determine if any chemical agent, regardless of its nature, placed in the flood water could be effective in influencing the mechanism of displacement of the oil by water. It has been known for many years that water does not displace all the oil in a reservoir because a portion of the oil is "trapped" and held immobile by capillary forces. This oil is trapped within the pores of a water-wet rock when it becomes broken into discontinuous globules. Initially, when oil is present at high saturations within the pores of a water-wet rock, the connate water forms rings around the points of contact of the sand grains and may even completely fill small cavities between grains, whereas the oil occupies the larger void spaces between the grains.&apos; Under these conditions, the oil in these spaces is in the form of irregular but continuous filaments, the diameters of which depend on the geometry of the sand pores. The filaments are formed by the oil contained in the small cells which are formed between the sand grains and are connected to their neighboring cells by channels or tunnels formed by pendular rings of water. At a high oil saturation, the oil filaments conform approximately to the shape and size of the cells and their connecting tunnels. Starting with this distribution, as the water saturation is increased the water layers in the small cavities and on the surface of the grains grow. As this occurs, the water rings grow and the diameters of the oil filaments decrease. When an oil filament is reduced to a critically small diameter, the filament breaks, and its tunnel fills completely with water. Any oil which remains within a cell after all its connecting tunnels have been water-filled is trapped as a discontinuous globule. Once the oil has become trapped, the capillary forces oppose distortion of the globules and may prevent their being squeezed through the water-filled tunnels. Only a very small pressure gradient is sufficient to keep oil moving as a continuous filament. On the other hand, once the filament has broken into discontinuous oil droplets a relatively large force is required to distort the surface of a drop and move it through a water-

Jan 1, 1958

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By W. K. Lewis, Lombard Squires, W. I. Thompson

The authors presented an article2† last year on colloidal properties of clay suspensions in which they attempted to sustain the position that the behavior of clay suspensions is due primarily to the mechanical interference of the platy particles, the nature and extent of the interference being profoundly influenced by the character of the surfaces of the particles, which in turn is determined primarily by the nature and amount of adsorbed foreign materials held on the surface of the particles by forces which are predominantly chemical in type. The following discussion is a continuation of that article to extend these same interpretative points of view to the behavior of clay gels. Insight into the mechanism of gelation is certainly of outstanding importance in the handling of drilling muds. In the former article it was suggested that the thin, flat plates that constitute the ultimate clay particles may build up aggregates by the overlapping of the ultimate plates face to face much longer and perhaps also much wider than the ultimate plates themselves, but not appreciably thicker. Exhaustive microscopic examinations of characteristic clays show no tendency for the larger particles, clearly visible under the microscope, to orient themselves in this way. It is true that the gelation of the clays is due primarily to the smallest particles, unresolvable other than by the ultramicroscope, so that the possibility of the deve1opment by them of an overlapping structure is not excluded. Furthermore, as one approaches the limit of resolving power of the microscope, the difficulty of observing accurately the shapes and relative positions of particles incresses excessively. However, in the absence of any observable tendency toward overlapping orientation of the large, visible particles, one hesitates to ascribe such a tendency to the smaller particles beyond the range of visibility. Should it develop that one must exclude the assumption of overlapping orientation, the explanations offered in the previous article are changed in only one respect; namely, one would now have to assume that the ultimate particles themselves have length, and probably also width, very large in comparison with their thickness.

Jan 1, 1936

By H. R. Aldrich

This paper presents some of the results obtained during the field season of 1919 while mapping, in detail, the stratigraphy of the Gogebic Range in Wisconsin. The detailed stratigraphic section for the range was first published, in 1919, by W. 0. Hotchkiss,1 State Gcologist of Wisconsin. The idea of the continuity of the definite succession thus established was the result of underground work in the productive part of the range in Michigan and Wisconsin, where most of the required data also were obtained. The bulk of the range in Wisconsin is heavily covered by drift; in fact, there is but one satisfactorily exposed section across the entire formation, few partial sections, and only scanty outcrops of any size. Evidently mapping of the detailed members of the formation could only be established at a few points; and if from these small areas the .unexposed portions were to be mapped by projection, the only apparent method for projection was straight-line interpolation modified or supported by data from the scanty outcrops and from test workings. It was found that by tracing a magnetic line, the position of which in the formation may be determined from test pits and outcrops, the projection of that member through the drift-covered areas can be accomplished. The magnetic line serves as a datum horizon within the formation to which reference may be made in correlating outcrops and ledge matter thrown from test workings. The foot wall is easily located also, and from the two datum horizons thus available and the known proportional thickness of the several members in the type sections, outcrops and artificially exposed ledges can be correlated by lithological characteristics. As a result, the tracing of magnetic lines became the basis of our work on the stratigraphy and we were able to carry the mapping of detailed members throughout the length of the range. It was found that the magnetic horizon at the base of the Tyler slate was most easily followed by the dip needle; that discontinuity caused by cross-faulting could be established; that folding along the strike could be detected in a repetition

Jan 1, 1922

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By R. W. Raymond

THE question, what is the best proportion among weight, fall, and speed of stamps, is one which has not yet received thorough and systematic examination. In considering the economical application of stamping machinery, we meet, at the beginning, with serious difficulties in obtaining accurate data for comparison. The weight and fall of stamps vary as the shoes and dies wear out; and this may lead to a change of speed also. Moreover, defects in engines, boilers, or machinery for the transmission of power, may occasion serious losses, which cannot fairly be charged to the arrangements of the stamps proper. Again, the capacity of stamp-mills is directly dependent, in some degree, upon the nature and extent of discharge, fineness of screens, and other peculiarities of the battery. Finally, the hardness and tenacity of the rock crushed varies so much that comparisons between different localities cannot be implicitly trusted. The safest experiments are those made in the same mill, by changing first one and then another condition of working; but this is seldom possible for such conditions as weight and lift of stamps, and only within narrow limits for their speed. We may eliminate of friction, transmission, and generation of power, in the case of stamps, by measuring the power actually developed by their fall. Thus, the weight, multiplied into the fall in feet, and the number of drops per minute, gives us exactly the number of foot-pounds exerted by each stamp. Dividing by 33,000, the number of foot-pounds per minute in one-horse power, we have the horse-power per stamp, from which the effective power of the whole mill may be obtained. Dividing the amount of rock crushed daily by the effective horse-power, gives us the daily amount per horse-power ; and this is the best measure that can be obtained for the effectiveness of the stamps. A complete discussion of the subject would require us to determine the exact influence of the discharge, etc., and the exact resistance offered by different classes of rocks, for both of which points the data are wanting. Professor J. D. Hague, in the third volume of the United States Geological Exploration of the Fortieth Parallel, gives a valuable

By Charles Stuart

A PAPER on this subject can cover but a limited range. A thorough visualization of the subject would contemplate a comparative analysis of haulage machines and batteries of various types; the relationship of the storage-battery locomotive to other types of mine haulage should be considered and limiting factors in each case should be carefully developed. This paper will briefly deal with these factors. So far as the writer has been able to determine, the first storage-battery locomotives for mine haulage were manufactured in 1897 or 1898 and were tried out in the Pocahontas coal field, but they were not sufficiently satisfactory to justify their continued use. Battery explosions were frequent and caused serious damage to the wiring, electrical equipment, and the clothing and bodies of the motormen. Sulfuric acid was used as the electrolyte. Experiments were then conducted with locomotives bearing reels of flexible cable through which connection between the motors of the locomotive and the trolley wire was maintained. At first, these reels were turned by hand. Later, the reels were revolved by contact with the wheels of the locomotive, being raised out of contact with the wheels, by a lever, when necessary. About 1902, the plan of operating the reel, by chain and sprocket wheels, from one of the locomotive axles, as is still the practice, was devised. The popular floating motor-driven reel had its inception in the Pocahontas fields prior to 1906. The maximum radius of operation of the reel-type locomotive is about 500 ft. (150 m.) from point of connection with trolley wire. This is ample for room work and certain entry work, but the need for a machine that would operate entirely independently of the trolley wire was so great that, with the development of the storage battery, renewed efforts were made to manufacture a successful storage-battery locomotive. About 1908, the gasoline locomotive was introduced. In spite of many objections to this type of machine for such work, the fact that hun¬dreds of these machines were purchased was proof of the need for a machine operating independently of the trolley.

Jan 1, 1922