Search Documents

By J. E. Breen, J. Weertman

The creep rate of polycrystalline tin was studied as a function of temperature and stress in constant stress experiments. The temperature was varied from room temperature to almost the melting point of tin. Activation energies were calculated from tests run at the same stress. It was found that on a log creep rate vs inverse temperature plot the experimental points did not fall on one straight line but on a line which changed its slope in the 90° to 160°C region. Two activation energies for the creep of tin can be calculated from the data: a value around 26,000 cal per mol at high temperatures and a value around 11,000 cal per mot at low temperatures. It is suggested that the discrepancies between the creep activation energies and those of self-diffusion can be accounted for if self-diffusion takes place predominately by Zener's ring mechanism rather than through vacancy or interstitial movement. SHERBY, Orr, and Dorn' and Dorn' have recently reviewed some of the data on high temperature creep of metals. -The data show that the activation energy of high temperature creep is approximately equal to the activation energy of self-diffusion. This same correlation has also been successfully made between the activation energy of grain boundary relaxation and that of self-diffusion.3,4 The metal tin does not fit into this simple picture. Its activation energies of self-diffusion differ appreciably from that of grain boundary relaxation and of creep. Fensham,5 from a precisely performed experiment, has determined that the activation energies of self-diffusion of tin are 10,500 and 5,900 cal per mol along the C and A axes, respectively. There are two energies because of the anisotropic nature of tin. Rotherham, Smith, and Greenough6 have shown that the grain boundary relaxation activation energy is 19,000 cal per mol (measurements made from room temperature to 100°C). Puttick and King7 found the same activation energy for grain boundary slip in bicrystals of tin (180° to 225°C region). Until recently, there was no high temperature large strain creep data on tin suitable for activation energy calculations. At rather small strains (up to 0.01), Tyte8 had made a series of measurements on tin from which activation energies can be calculated. In Fig. 1 are plotted some of his data on a log creep rate vs inverse temperature graph. It can be seen that Tyte's work indicates that at a relatively low temperature the activation energy is around 7,400 cal per mol but at higher temperatures the activation energy increases. Since Tyte measured the creep only for small strains, it is doubtful if a

Jan 1, 1956

By E. A. Anderson, M. L. Fuller

The copper-zinc phase equilibrium diagram has been the subject of many investigations. Until recently, however, the boundary of the terminal solid solution of copper in zinc (eta) has not been thoroughly investigated. This paper reports determinations of the solid solubility of copper in zinc at temperatures from 100' to 400' C., the course of the liquidus and solidus for the eta solid solution and determinations of the peritectic temperature and peritectic point for the reaction between epsilon and the melt to form eta. The liquidus of the eta phase was determined by thermal analysis and the solidus by the microscopical examination of specimens quenched from temperatures above and below the solidus. The temperature of the peritectic horizontal was obtained by thermal analysis and the composition at the peritectic point was determined by extrapolation of the solid solubility boundary of the eta phase to the peritectic horizontal. The solid solubility boundary of the eta solid solution was investigated very carefully. Particular care was used to achieve equilibrium in the alloys at each temperature selected. The X-ray, electrical conductivity and microscopical methods mere used in determining the solid solubility limits. The X-ray method measures the changes in the solvent lattice with increasing solute content and in this manner locates the composition of the alloy at which no further change in the solvent lattice takes place, the limit of solid solubility. The method of electrical conductivity measures the conductivity of the alloys of a graded series of compositions, whereby the solubility limit is indicated by a discontinuity in the conductivity-composition relationship. The microscopical method distinguishes, by direct inspection, between the homogeneous solid solution alloys and those having a secondary constituent in addition to the solid solution phase, and thus indicates from the examination of a series of alloys the solid solubility limit.

Jan 1, 1934

By J. G. Morlet, A. R. Troiano, H. H. Johnson

Delayed failure in steel occurs by controlled initiation and growth of a crack. The incubation period for crack initiation was measured. Crack initiation and Propagation are controlled by interaction between hydrogen concentration and triaxial stress state. The incubation period results from stress-induced diffusion of hydrogen to the point of crack initiation. THIS paper describes the phenomenon of delayed failureland the kinetics of crack initiation and propagation in uniformly hydrogenated steel. The investigation was prompted by service failures of high-strength-steel components at applied stresses far below the conventional yield strength, after the part had successfully sustained equal or higher stresses for an extended time interval. This delayed failure phenomenon, often termed static fatigue, is associated1 with the presence of hydrogen. This is not surprising, since the voluminous literature on flaking and hydrogen embrit-tlement demonstrates that hydrogen may exert a potent embrittling influence. Flakes, or internal hairline cracks in alloy-steel forgings, are related to the presence of hydrogen retained from the steel-making process.2 On the other hand, embrit-tlement arises from hydrogen introduced during surface treatments such as acid pickling or electroplating. Laboratory delayed failures have been induced in notch specimens of 4340 steel by electrolytic charging of the specimen surface with hydrogen and subsequent static stressing.l,4,5 Static fatigue was observed over a wide range of applied stresses; however, failure did not occur below a critical applied stress, designated as the static fatigue limit. In this instance the extended time for failure resulted primarily from the macroscopic redistribution of hydrogen. A crack formed to the depth of the hydrogen enriched "case* upon loading; further crack growth naturally awaited diffusion of hydrogen into the material ahead of the crack. The crack-propagation rate was therefore controlled primarily by the macroscopic diffusion of hydrogen into the specimen interior during the test. Thus, in this instance static fatigue was associated with the movement of a gross concentration gradient. However, delayed failure in steel of uniform hydrogen concentration is of greater fundamental interest, as well as commercial significance. With a homogeneous hydrogen distribution a different mode of delayed failure might be expected. As the heterogeneous hydrogen distribution became more uniform,4,5 the initial crack-propagation rate decreased markedly and, in fact, what appeared to be an incubation period for crack initiation was observed. However, the macroscopic concentration gradient precluded an accurate evaluation of these observations. Although the existence of an incubation period, up to this time, has not been established definitely, it is not amiss to point out some implications of the concept. It is of interest in all hydrogen-induced embrittlement phenomena, such as flaking, delayed failure, and hydrogen embrittlement. Much discussion has centered around the possibility of an

Jan 1, 1959

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922

By Frank L. Nason

(New York meeting, February, 1912) IN the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States, 1,100,000,000 Great Britain, . 1,000,000,000 Germany, 2,200, 000, 000 Spain, 500,000,000 Russia and Finland, 1,500,000,000 France, 1.500, 000, 000 Sweden, . 1,000,000,000 Austria-Hungary, . 1,000,000,000 Other countries, 1,200,000,000 Total, . 10,000, 000, 000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at the present rate of consumption. On the other hand (according to Edwin C. Eckel,1 from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the, next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates arc definitely, but by no means finally, given for the United States District. Tons. Lake Superior District, . . 1,500,000,000 to 2,000,000,000 Alabama, red hematite. . . 1,000,000,000 brown hematite, 725,000,000 Georgia, red hematite, 200,000,000 brown hematite, 125,000,000 Tennessee red hematite, . 6110,000,000 I brown hematite, 225,000,000 Virginia., red hematite, 50,000,000 brown hematite, 300,000,000 Total, . . 4,725,000,000 to :5,225,000,000

Jul 1, 1912

By CLARESCE CARLETON SEJIPLE

(Wilkes-Barre Meeting, June, 1911.) AT a number of mines in eastern Nicaragua, 3.5- and 5-ft. Huntington mills are used for grinding gold-ore after a preliminary breaking in jaw-crushers. The smaller mills are made sectional to facilitate transportation to the more difficultly accessible mines. The capacity of the smaller mills is about 20 or 25 per cent. that of the larger, but in proportion to the quantity of ore ground they require more power and are subject to greater wear. The notes herein given are from records of the performance of the larger mills, but, in general, apply to the smaller also. THE NATURE OF THE ORE. The ore occurred as a series of flat veins in a highly-decomposed rock, probably alaskite. The primary mineralization comprised pyrite, pyrrhotite, marcasite, chalcopyrite, and quartz; the oxidation-products of which were chiefly hydrated iron oxide or limonite, chrysocolla, azurite, and malachite. The kaolinization of the feldspar of the country resulted in the admixture of a great quantity of clay with the oxidized ore. The quartz was sandy, imbedded in the clay; and probably the greater part represented the residue from the crushed rock in the fissures after leaching, and kaolinization of the feldspar. There was little vein-quartz in the unaltered primary sulphide ore. Only the oxidized ore was mined for the gold that it contained in amounts that averaged $4 per ton. No specks of gold were ever seen in the ore, and the gold obtained by panning was always exceedingly fine. The amalgamation-bullion was about 800 fine in gold and 60 to 80 in silver. The ore delivered at the mill contained from 5 to 15 per cent. of moisture; during the rainy season the quantity was much greater. The moisture and clay made the ore so sticky that it had to be raked over steeply-inclined grizzlies; it hung in the ore-bins,

Oct 1, 1911

By S. J. Prison, C. R. Smith

The effect of fluid injection to control water coning in oil and gas wells was investigated. Analytical and model techniques were employed. The factors investigated were the position and length of the completion interval, the point of fluid injection, the viscosity of the injected fluid and the relative thickness of the oil and water sections. The resulting influence of these factors on the net producing water-oil ratio was determined. Several important conclusions can be drawn from the study. In general, it was found that the net producing water-oil ratio can be reduced by fluid injection. The magnitude of this reduction depended on the factors listed above. An important practical consideration is that the injection fluid may be either oil or water. If the injected fluid is less dense than the connate water of the reservoir, the fluid will not be lost. This fact is reassuring when valuable oil is being injected. Efforts to suppress water production were more successful when the injection fluid was more viscous than the reservoir oil, or when a zone of reduced permeability existed in the vicinity of the point of fluid injection. Under test conditions, little benefit was derived through the use of impermeable barriers or cement "pancakes". INTRODUCTION The occurrence of water coning has been known for at least 60 years. In thin oil or gas pay sections, the presence of an oil-water or gas-water contact hinders production and often causes early abandonment of the afflicted well if a completion is even attempted. Even when relatively thick pay sections are found, the encroachment of water when a water drive is present will eventually pose serious water coning problems. This water is often corrosive, expensive to separate from the oil or gas and is costly to dispose of. The theory of water coning has been discussed by a number of authors. 1,2,3,4 Briefly, water coning to the producing interval in a well is due to pressure gradients resulting from the production of fluid from the reservoir. These pressure gradients will cause a water cone to rise toward the bottom of the producing interval if a water-oil or water-gas contact exists. The tendency of the water to cone is offset or partially offset by gravity forces since the water has a higher specific gravity than the oil. A balance then exists between two forces, gravitational forces arising from the difference in specific gravities of the oil and water, and the pressure gradients causing the flow of fluids to the wellbore. If the pressure gradient exceeds the gravitational force, water coning to the wellbore occurs and water production results. Through the years considerable thought has been given to the water coning problem. More than 50 U. S. Patents have been granted to inventors on the subject. A relatively complete literature review of the water coning problem has been made. 5 A number of these patents hold considerable promise for the solution or the partial solution of the water and/or the coning problem. Very little has been written describing field tests of techniques for the suppression of water coning. A notable exception is the paperby West. 6 He reports success in reducing gas coning by a combination of gravel packing and oil injection above the oil-producing interval. He also describes a comparable method to prevent water coning, but provides no field examples. This study experimentally and analytically verifies the benefits of oil injection as a means of partially or completely suppressing the water cone. While the gas coning problem was not treated, it is anticipated that results comparable to those obtained in water suppression could be obtained with reduced oil injection since the viscosity contrast between oil and gas exceeds that between oil and water. For the purpose of this study, the conventional potential flow theory was applied to the water-coning problem. The experimental verification centered on both a radial and a linear model. The model study permitted the investigation of complex flow configurations and the use of fluids of differing densities and viscosities. No analytic expressions are available to permit a solution of the problem as stated (see Fig. 1).

By Charles Pack

EXTENSIVE progress has been made in the metallurgy of alloys for die castings. Enthusiastic proponents of some alloys are inclined to make extravagant claims for their materials, which may be justified by physical tests on test bars made from the respective alloys but are seldom justified by the results obtained with commercial die castings made from those alloys. Chemical analysis of the test bars and castings fails to determine the cause of these variations, since they are due to other physical factors entering into the commercial production of die castings. In this paper, an attempt will be made to outline some of the factors in commercial die-casting practice to which these variable results may be attributed, in the hope that the manufacturer of die castings, recognizing the importance of these factors, will devote more attention to them in the design and construction of dies and equipment. In 1914,1 the author defined die castings as "metal castings made by forcing molten metal, underpressure, into metallic molds or dies." This definition was given in order to differentiate die castings from other molded metal products such as "permanent-mold" castings, "slush" castings and similar products that are sometimes erroneously termed die castings. The term "die casting" could be interpreted to include all castings made in metal molds or dies; but since this term, like most of our technical nomenclature, has been developed by commercial practice we must look to this practice for its proper definition. The Germans, with their usual devotion to descriptive names, have adopted the name of spritzguss (squirt cast) for die castings. Undoubtedly this name is more descriptive of the die-casting process, where the metal is literally squirted into the die and serves to differentiate this process from other metal mold processes, where the metal is poured into the die. In the earlier paper mentioned, the author also emphasized the fact that the definition given for die castings indicated clearly that the satisfactory operation of the process must comprise three factors, all of which must be considered of vital importance to the successful operation of the die-casting process:

Jan 1, 1930

By Arthur Philips

THE purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreover, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the tests and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstructure of white cast iron by annealing at different temperatures within the range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800° C.

Jan 1, 1922

By J. R. Linney

APPROXIMATELY 5,788,000 long tons of crude ore was produced by the Eastern magnetite industry in 1946, or a drop of 26 per cent compared -with 1945. Decrease in production -throughout the industry varied from :8 per cent for the mine with the lowest reduction to 49 per cent for the mine -with the highest reduction. At the Chateaugay mine, operated by :the Republic Steel Corp. at Lyon Mountain, N. Y., 426,900 long tons of crude ,ore was produced, yielding 129,500 long tons of concentrates or a reduction of 46 per cent compared with the previous year. Owing to a strike the mine was closed down from Jan. 21 to July 29. At the Mineville mines, also operated by Republic Steel, output was 755,000 long tons of crude ore or a reduction of 49 per cent compared with 1945. The yield from the crude ore production consisted of 51,500 long tons of lump ore and 380,000 long tons of concentrates. The Mineville plant did not operate from March 17 through July 28, on account of the strike. The Fisher Hill mine, which produced 93,000 long tons of crude ore, included in the above figures, has not operated since March 17, 1946.

Jan 1, 1947

By Charles Pack

Extensive progress has been made in the metallurgy of alloys for die castings. Enthusiastic proponents of some alloys are inclined to make extravagant claims for their materials, which may be justified by physical tests on test bars made from the respective alloys but are seldom justified by the results obtained with commercial die castings made from those alloys. Chemical analysis of the test bars and castings fails to determine the cause of these variations, since they are due to other physical factors entering into the commercial production of die castings. In this paper, an attempt will be made to outline some of the factors in commercial die-casting practice to which these variable results may be attributed, in the hope that the manufacturer of die castings, recognizing the importance of these factors, will devote more attention to them in the design and construction of dies and equipment. In 1914,l the author defined die castings as "metal castings made by forcing molten metal, under pressure, into metallic molds or dies." This definition was given in order to differentiate die castings from other molded metal products such as "permanent-mold" castings, L'slush" castings and similar products that are sometimes erroneously termed die castings. The term "die casting" could be interpreted to include all castings made in metal molds or dies; but since this term, like most of our technical nomenclature, has been developed by commercial practice we must look to this practice for its proper definition. The Germans, with their usual devotion to desecriptive names, have adopted the name of sprilzguss (squirt cast) for die castings. Undoubtedly this name is more descriptive of the die-casting process, where the metal is literally squirted into the die and serves to differentiate this process from other metal mold processes, where the metal is poured into the die. In the earlier paper mentioned, the author also emphasized the fact that the definition given for die castings indicated clearly that the satisfactory operation of the process must comprise three factors, all of which must be considered of vital importance to the successful operation of the die-casting process:

Jan 1, 1931

By John H. Schissler

INTRODUCTION AND SUMMARY Complex copper-lead-zinc ore is mined from underground workings high in the Western Cordillera of the Andes mountains about 100 km in a stralght line north of the city of Arequipa in southern Peru. The Madrigal mine is situated in a steep-walled canyon into which the six operating levels "daylight". Production is from cut-and-fill stopes currently producing approximately 740 dry metric tons per day. The Santa Rosa vein, the most important producer in the district, outcrops for a distance of about 4 km, bearing N 75º W and dipping about 70º NE. In places the vein splits into two or three branches; widths of each vary between 1 and 4 m and total mineralized widths of up to over 8 m occur. Principal ore minerals are chalcopyrite, galena and sphalerite. Ore reserve grades for the Madrigal mine average about 1.45% Cu, 2.6% Pb and 5.0% Zn, 2.9 ozAg per metric ton. [Compania] Minera del Madrigal is a California limited partnership; the general partner and operator is [Compania] Madrigal, a wholly-owned subsidiary of Homestake Mining Company. HISTORY Shallow workings found on the Santa Rosa vein were probably made by the Spaniards during colonial times in their search for

Jan 1, 1977

By V. Jares

DESPITE the fact that a combination of metals-aluminum-zinc-tin, and sometimes aluminium-zinc-cadmium-is extensively used for aluminum solders, as well as for die-castings, the constitution of these alloys has not yet been made clear. I. BINARY SYSTEMS The system aluminium-zinc is the basis of the ternary alloys under consideration. Their composition was made sufficiently clear by the investigations of Roscnhein and Archbutt,1 Bauer and Vogel,2 Sander .and Meissner,3 Hanson and Gayler4 and Isihara.5 Only the temperature of decomposition of the crystals s seems still to be doubtful, whether it is considered as a compound of Al2Zn3 (according to Bauer and Vogel) or as an intermediate phase of variant composition (according to Hanson and Gayler). This temperature is given by most of the authors, as in the neighborhood of 256° C., only Isihara giving 280° C. As its accurate determination is of special importance in the study of the ternary alloys under consideration it was experimentally controlled in the following manner: An alloy corresponding in composition to the formula Al2Zn3 was made, in which the temperature effect was found to be the greatest. This was drilled and a silver-constantan thermoelement inserted into the cavity so as to be in direct contact with the alloy. The whole was then very slowly heated and the heating and cooling curves determined. The transition temperature from the heating curve was found to be 281° C., whereas-from the cooling curve it was 252° C.

Jan 10, 1926

By Joseph R. Hatch

When compared to average shale composition, average coal is enriched in sulfur and selenium, has similar amounts of arsenic, beryllium, lead, antimony and molybdenum, and is depleted in at least 26 other elements. Within a coalfield, or region, some coals are enriched (10X average shale) in silver, arsenic, cadmium, cobalt, germanium, molybdenum, nickel, lead, selenium, uranium, and zinc. Important factors controlling element distributions in coal include geochemical conditions (primarily pH) in the peat swamp, composition and depositional environment of coal roof rocks, thermal maturity (rank), nature and intensity of any epigenetic mineralization, composition of ground waters that come in contact with the coal, and degree of weathering.

Jan 1, 1983

New York State Museum, Albany, N. Y. D H. Newland, State Geologist. A complete list of publications or the latest lists of available publications will be sent upon application. A series of Bulletins on The Mining and Quarry Industry of New York are available as follows: Bulletin 51 (1910), 15 cents; 161 (1911), 20 cents; 166 (1912), 20 cents, 174 (1913), 20 cents; 190 (1915), 15 cents; 277 (1925-26), 50 cents; 295 (1927-1929), 40 cents. Another series discusses the Geology of the State by Quad¬rangles, available as follows: Bulletin 153, Broadalbin Quad (1911), 25 cents; 154, Sche¬nectady Quad. (1911), 20 cents, 170, North Creek Quad . (1914)

Jan 1, 1933

By B. J. Guarnera

There have been major changes in the makeup and nature of the uranium exploration industry in recent years. Significant price increases precipitated an increase in exploration activity-according to the Department of Energy, exploratory drilling in 1977, by 140 companies, was almost 8 million m (26 million ft). This represents a 37% increase over the prior year's drilling. Projections for 1978 indicate at least 9 million m (30 million ft) of exploratory holes will be drilled in the US. Exploration expenditures in 1979, including land acquisition, drilling, and other costs, were estimated by DOE at over $236 million. Domestic expenditures for 1978 are estimated at over $250 million.

Jan 10, 1978

By H. K. Shearer

Drilling for oil and gas in Arkansas in 1934 showed more activity than in any year since 1929; with a total of 96 completions, including 36 oil wells, 1 gas well and 59 dry holes. Of the producers, the lone gas well and 35 oil wells were in old fields, and one wildcat producer opened a new pool. Of the dry holes, 16 were in or near fields and 43 were wildcats. The total reported initial daily production of the oil wells was 9013 bbl., averaging 252 bbl. per well. Active drilling operations numbered 65 at the close of the year, compared with 26 at the beginning.

Jan 1, 1935

Albin. B . R Billings. Mont . '28 Amnter . Nathan L 26 Broad St.. New York . N . Y . '28 Bache . Jules S 42 Broadway. New York. N . Y . '28 Borrett . C . P . 5338 Harper Ave .. Chicago. I11 '28 Baum . Frank G. . Cons . Hydro-Electric Engr Camel'. Shasta Co. . Cal. '23 Baylean, William S Russ Bldg .. San Francisco. Cal . '28 Bean, Louis H .. V.P.. Dwight P . Robinson & Co.. lnc 126 E . 46th St New York. N . Y . '28 Beatty . Roes J . 1106 First National Bank' Bldg .. Chicago . Ill . '28 Benwell . Oswald F . 110 Gilpin St .. Denver. 1310 . '28 Beymer. Albert 9.. V.P .. Keystone. National Bank Pittsburgh. Pa . '28

Jan 1, 1929

By S. S. Hsieh, J. R. Lehr

Bench scale beneficiation studies were made on Idaho dolomitic phosphate rock using the TVA carbonate flotation process. The process used diphosphonic acid as a phosphate mineral depressant and fatty acid as a carbonate mineral collector. Silica was subsequently rejected as float using an amine collector, with phosphate product recovered as the sink fraction. Two samples of prepared flotation feed from commercial operation were used. One contained 21% P205 and 3.2% MgO. The other contained 26% P205 and 1.8% MgO. The results indicate that concentrates containing 31% to 33% P205 and 1% or less MgO can be obtained, with about 80% P205 recovery.

Jan 1, 1986