Search Documents

By J. P. Zannaras

Referring to the article by R. J. Charles and P. L. de Bruyn, let us assume that W = weight of glass bar; P = weight of hammer; e = total deformation; K = unit of deformation; K = potential stress energy; E = modulus of elasticity; L = length of the bar; 7 = coefficient of inertia; h = height, ft; V = velocity, fps; and a = cross section area. The portion of kinetic energy which is effective in producing stress energy in a fixed bar struck horizontally is given by the formula" 1 + 1/3 W/P K =1+1/3w/p/(1+1/2w/p)2 P.V2/2g = Ph where 1 + 1/3 W/P ? (1 + 3W/P/(1=1/2w/p)2 [8] Putting e e = W/P =------------ From the above equation it can be seen that the maximum transfer of kinetic energy to stress energy is when e = 0 or W/P = 0 which indicates that the weight of the hammer must be very large as compared with the weight of the impacted rod. Eq. 8 diametrically opposes the conclusions reached by the authors of this article. In fact, if their suggestions were followed to the extreme when e = co when P = 0, there would be no transfer of kinetic energy to stress energy at all, as 7, becomes zero. Eq. 8 presumes that the velocity with which the stress is propagated through the bar is infinite, whereas the authors claim that the compression waves reflected are reaching the struck end of the bar prior to the complete transfer of the kinetic energy to cause such modification of the conditions there as to make them reach the reverse conclusions demonstrated by the above formula. That such interference exists is unquestionably demonstrated by the authors and others. However, if my observations are correct, such interference for this specific experiment and also for practical comminu- tion is insignificant, and the conclusions of the authors are in error and must be reversed to comply with Eq. 8. Eq. 5, w. = AE 2/2, given by the authors on page 51, is derived from the following equation (Eq. 9): K = 1/2Pe, where P = Sa, S = ?E, e = EL, and L = 1. The above formula, Eq. 9, cannot be applied in this case. This formula is applicable for static loads where the load increases from zero up to its final value, P, in such a way that the deformation at different instants is proportional to the loads acting at those instants and actually represents the area of a right triangle in the strain load diagram of base e and height P. The typical photographs shown in Figs. 3 and 4 represent the familiar strain load diagrams, and since the line of the wave marks the existence and intensity of the strain with the unquestionable conclusion that such strain has been caused by the action of a load acting continuously all along the wave until it reached the horizontal axis, the work stored at this point is represented by the area under the wave line and the horizontal axis and not by the area of the fictitious triangle given by the authors. Then if this is correct, even visual estimation of these areas at gage stations given in the typical photographs of Figs. 3 and 4 suffice to contradict the authors' calculation given in Figs. 6a and 6b and Figs. 7a and 7b. The typical photographs presented by Charles and de Bruyn show a considerable variation of the intensity of the strain at different stations but very small variation of areas which actually represent the stress energy at the corresponding stations. And, apparently, by squaring the small quantities, the authors magnified their error tenfold. J. M. Frankland's paperV iscusses the relative strain intensity and not the total energy for different types of impact loading. He states in his paper, "The reader is explicitly warned not to confuse the results in this report with those obtained when the load is applied by a blow as from a hammer. In this case the peak load rises to very large but mostly unknown values. The accompanying large deflections and stresses are the result of high values of P, not of the dynamic load factor n. According to Frankland "the dynamic load factor" is the numerical maximum of the response factor. It therefore appears that the authors followed the same procedure in obtaining the relative strain energy ab-

Jan 1, 1957

By Norman Lamont

The evaluation of certain reser-voir properties, such as porosity and fluid saturation, from electrical well surveys has been widely accepted in petroleum engineering. Various investigators have established relationships between these properties and certain parameters which affect the response of the electrical log. Among these are the resistivities of the mud, its filtrate, and its filter cake. In 1949, Patnode1 established a relationship between the resistivities of the mud and filtrate. The well logging service companies have contributed relationships for the mud-mud cake resistivities2,3 These have been valuable since it was the practice to measure only resistivity of mud at the well site. During the mid-1940's the industry began drilling wells with oil-emulsion drilling fluids. These were conventional aqueous muds with a dispersed oil phase. Since 1950, oil-emulsion muds have been used on an increasing number of wells each year. However, the practice of measuring only the resistivity of the mud at the well site has continued, and the mud filtrate and mud cake resistivities have been determined by the above-mentioned relationships. Service companies are now equipped to measure all three resistivities at the well site. An investigation was conducted on the resistivities of oil-emulsion muds, mud filtrates, and mud cakes to determine if these values conformed to the relationships for aqueous muds. TYPES OF MUDS Fifty-one oil-emulsion mud samples were prepared in the laboratory following a standard manual' published by a leading mud company. The diesel oil in the samples varied from 5 to 50 per cent, the majority of the samples being in the 10 per cent region. The basic aqueous mud types which were converted to oil-emulsion muds were commercial clay and bentonite muds, low pH and high pH, caustic-quebracho treated muds, and lime treated muds. The emulsions were stabilized by dispersed solids, lignins, lignosulfo-nates, sodium carboxymethyl cellulose, or sulfonated petrolatum. It is worthy of note that after a quiescent period of two weeks at room temperature all samples, regardless of emulsifying agent, remained stable. The make-up water for the muds was from the laboratory tap. Resistivities were varied by the addition of table salt to the water. A range of mud resistivities from 0.44 to 3.9 ohm-m was obtained in this way. Twenty-three field muds were tested. These covered the same range of mud types as did laboratory muds. Oil provinces of the Gulf Coast, South Texas, West Texas, Oklahoma, Montana, and Canada were represented. MUD TEST PROCEDURE Each mud was tested for density, viscosity, pH, and filter loss by standard testing techniques. The resistivity measurements were obtained with a Schlumberger EMT meter. This meter required small volumes of sample, e.g., 2 mm. Filtrate was obtained from a Standard Baroid fil-ter press at the end of a 30-minute test. The filter cake from the same test was used for cake resistivity measurements. Mud, filtrate, and cake samples were heated to 100" F in a constant temperature water bath prior to measurement of resistivities. RESULTS The relation between mud resistivity (Rm) and mud filtrate resistivity (Rmf) is shown in Fig. 1. The solid line represents an average for the data. The equation of this line is Rmf =0.876 (Rm) 1.075 . . (1) Arbitrary limits, indicated by the dashed curves, have been set. The majority of the data falls within these limits, but some points do lie outside the limits. The approximate equation Rmt = 0.88 Rm , . . . . (2) will give satisfactory results within these limits. The data on mud cake resistivity Rmc is shown in Fig. 2. The solid line is an average for the data. The equation for the line is Rmc = 1.306 (Rm)0.88 The dashed lines are arbitrary limits on the data. Within these limits, Eq. 3 may be simplified to Rmc = 1.31 Rm . . . . (4) DISCUSSION The limiting curves in Figs. 1 and 2 represent maximum deviations of ±25 per cent. Thus the use of the average curves can introduce considerable error. There is no substitute for accurate measurements of mud, mud cake, and mud filtrate resistivities at the well site. The mud sample tested should be representative of the mud opposite the formation being logged. The average mud filtrate resistivity curve of Fig. 1 is reproduced in Fig. 3 with two curves which have been published for clay-base aqueous muds2,3. The latter curves were determined from average values of a large number of drilling fluids. The three curves have essentially the same slope and the differences between them are from 7 to 22 per cent. Comparison is made only to illustrate the possibility of error

Jan 1, 1958

By R. A. Oriani

The partial molal volume of hydrogen is one of the parameters that describe the elastic interaction between the solute and the stress fields about inclusions, dislocations, and cracks. As such the partial molal volume is probably of importance in the elucidation of phenomena such as hydrogen embrittlement and hydrogen yield point. A knowledge of this quantity would also be helpful in thinking about the state of dissolved hydrogen in iron. However, because of the very low lattice solubility of hydrogen in iron the usual ways of determining the lattice expansion are not practicable. It is therefore of interest to apply the thermodynamics of stressed bodies to two sets of measurements of the effect of elastic stress upon the permeability of hydrogen in order to deduce a value of the partial molal volume, VH, of hydrogen dissolved in a iron. Beck ..' and previously de Kazinczy, observed that a uniaxial tensile stress increases the permeability of hydrogen in iron and in various steels. Beck et 01. employed Armco iron and A.I.S.I. 4340 steel, whereas de Kazinczy used a steel the composition of which was 0.13 C, 0.23 Si, 0.46 Mn, 0.006 P, and 0.038 S. Upon releasing the stress the permeability increment disappeared if the stress was below the elastic limit. Both investigators employed cathodic charging to introduce the hydrogen. de Kazinczy measured the permeation through a thin-walled tube by collecting the gas, whereas Beck et al. measured the permeation through sheets of various thicknesses by a very sensitive electrochemical technique. Both investigators measured the steady-state permeation at constant rate of hydrogen ion discharge, and Beck measured in addition the hydrogen diffusivity by a time-lag technique which is independent of the boundary conditions. Beck et al. and de Kazinczy found a linear relationship between log (J,/Jo) and the stress, where Ju/Jo is the ratio of the flux of hydrogen when the metal is under uniaxial tensile stress, a, to the flux under zero stress, for the same temperature and charging current. Beck et al. found in addition that the diffusivity of hydrogen is not changed by stress. Both investigators concluded that the observed change in permeability is due to an increase in hydrogen concentration, and furthermore that the increase in concentration is due directly to the thermodynamic effect of stress upon concentration. Accepting this assessment of the situation for reasons given below, one may use the equation3j4 in order to evaluate I/H, the partial molal volume of hydrogen. This equation is valid for the domain of a/E «¦ 1 (where E is the Young's modulus) and under the assumption that hydrogen expands the lattice isotrop-ically. From the data of Beck el al, one calculates V7H - 2.0 cu cm per g-atom, and from those of de Kazinczy one obtains 1.8 cu cm per g-atom. That the increase of concentration with stress is indeed of thermodynamic origin is attested to by the facts that the experimental results conform to the thermodynamic relation, Eq. [I], and that the results are the same whether a pure iron1 or each of two different steels172 is used. Neither of these facts wou1.d necessarily be expected if the effect of stress were, rather, to increase the ratio kn/k, of the kinetic factors of the following competing reactions: H(ads) — H (dissolved) Such a change of kinetics at the surface could be an alternative explanation of the effect of stress on the permeability. Although this writer does not deem this explanation to be the correct one for the reasons given above, it must be admitted that unambiguous proof that the phenomenon has a thermodynamic origin does not yet exist. Two kinds of experiments may be suggested. One is to plate a variety of metals on the input surface of the steel and repeat the stress experiment at a variety of hydrogen charging currents. The other is to employ somewhat thicker specimens in order to be able to apply uniaxial compressive stress. Eq. [I] shows that ln(c,/c,) depends on the sign of the stress, but it is difficult to see a physical basis for which k2/kl would depend on the sign of a. The present value of V^ in a iron agrees with phragmen's5 estimate, which he based on comparisons with the lattice expansion by hydrogen of titanium, zir-

Jan 1, 1967

By Irving B. Cadoff, Alvin A. Machonis

The resistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured as a function of temperature for cation-rich alloy single crystals covering the composition range across the PbTe-SnTe system. Alloying of PbTe with up to 20 pct SnTe was found to have little effect on the energy gap. Above 20 pct SnTe the alloys were "p" type but below this range the sign could be varied by heat treatment. The lattice thermal resistivity of the compounds SnTe and PbTe is raised by alloying one with the other. Z values in the order the interesting values obtained. THE PbTe-SnTe system has several interesting features. For one, PbTe is a useful thermoelectric material and the possibility of improving its figure of merit by alloying with SnTe, an isomorphous compound, has been suggested since these pseudo-binary solid solutions generally have a more favorable ratio of electrical conductivity to thermal conductivity than either of the components.' Other interesting features relate to the conductivity mechanism, band structure, and stoichiometry of the compounds and their alloys. PbTe is a semiconductor with an energy gap of about 0.29 ev2 at room temperature whose conductivity sign and magnitude can be varied from "n" to "p" by controlling the proportion of lead and tellurium with respect to the stoichiometric ratio.3 Excess lead results in "n"-type conduction. SnTe is found to exist only as a "p"-type material of relatively high conductivity. This behavior is attributed to stoichiometric deviation by Brebrick4 but Sagar and Miller proposed that the behavior of SnTe must be due in part to the presence of an overlapped band. An investigation of alloys of this system, therefore, might give additional information which would permit one to evaluate which of the two proposals is the more appropriate one. Abrikosov et al.' studied the room-temperature electrical properties of these alloys and reported data for Seebeck coefficient and resistivity on poly-crystalline alloys. The present work is a more exhaustive survey of the PbTe-SnTe system. Re- sistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured over a wide temperature range for single crystals at 10-pct intervals of lead/tin ratio across the pseudobinary system. The relative concentration of tellurium was controlled so as to obtain metal-ion excesses in all cases. SAMPLE PREPARATION The crystals were prepared by melting elemental lead, tin, and tellurium in weighed proportions in evacuated Vycor capsules. The lead and tellurium were high-purity grades obtained from American Smelting & Refining Co. The tin was supplied by Comico. The proper calculated proportions of lead, tin, and tellurium were weighed and charged into prepared Vycor capsules prior to evacuation. The capsules were prepared from 15-mm Vycor tubing. A sharp point was worked on one end of the tube. A pyrolytic graphite coating was deposited on the Vycor walls by heating the tip to 800°C in an atmosphere of acetone-saturated argon. An additional coating of graphite was deposited on the pyrolytic coating from an Aquadag suspension. Above the coated tip the tube was reduced in diameter to form a constrictive neck. To avoid scratching the graphite coatings the charge was placed in the tube above the constriction. After a low-temperature bake, the evacuated capsule was sealed. On subsequent heating the charge melted down into the lower portion of the capsule. The crystals were grown by lowering the capsule through a Bridgman-Stockbarger furnace. The lowering rate was 1 in. per 8 hr. The upper portion of the furnace was set for 950°C and the lower portion for 800°C. In general the yield of single crystals was about 25 pct. The mixed compositions were, as expected, the most difficult to grow. The finished crystals were sectioned into 5/8-in. slices. The tip, end, and middle slices from each crystal were analyzed by X-ray fluorescence to determine the lead-to-tin ratio. The resulting values were used to plot a composition vs distance plot for each crystal. Slices were selected from each crystal, with the aid of the composition plots, to cover the complete range of compositions at 10-pct intervals. In general, the slices selected were taken from the seed end of the crystal where the longitudinal segregation (as determined from the X-ray fluorescence analysis) was a minimum. Laue single-crystal analysis and metallographic analysis was used to verify if a slice was single or polycrystal. Any grain boundaries were clearly visible in the as-cut and polished condition. In ad-

Jan 1, 1964

By D. W. Lillie

It has been demonstrated that considerable bend ductility exists in bulk specimens of polycrystalline high-purity silicon. The possibility of hot-forming at 1200°C is suggested. EXCELLENT corrosion resistance in many media and low cross section for absorption of thermal neutrons (0.13 barn) would make silicon of interest to nuclear engineers were it not for extreme brittle-ness and the difficulty of fabrication by any reasonable means. The use of silicon for structural purposes also has been considered in view of its light weight and oxidation resistance. Johnson and Han-sen' have investigated the properties of silicon-base alloys and concluded that there was no way of making pure silicon or silicon-rich alloys ductile at room temperature. In view of reports of appreciable ductility in germanium single crystals above 550°C'." and some plastic deformation in single-crystal silicon above 900oC,' the present investigation was undertaken to define more precisely the limits of high-temperature ductility in pure silicon. After this investigation was begun torsion ductility in both germanium and silicon was reported by Greiner." Through the courtesy of F. H. Horn, a small bar of cast extra high-purity silicon was obtained and small bend specimens were made from it by careful machining and grinding. All of the reported tests results were obtained from samples from this bar (bar No. 1) and one other of similar source (bar No. 2). No complete analysis was obtained but, based on analysis of similar semi-conductor grade material, metallic impurities were under 0.01 pct total. Vacuum-fusion analysis for oxygen showed a value of 0.0018 2 0.0003 pct for the first bar tested and metallographic analysis showed no evidence of a second phase. Bend tests were carried out on an Instron tensile machine using a bend fixture with a 1 -in. span loaded at the center. Supporting and loading bars were 0.250 in. round and the load was applied by downward motion of the pulling crosshead of the machine. Specimen thickness and width were approximately 0.10 in. and % in. respectively. Loading rate was controlled by holding crosshead motion constant at 0.02 ipm. In some cases a smaller specimen was used on a 5/8-in. span with a 0.129-in.-diam loading bar. The entire bend fixture was surrounded by a hinged furnace and all heating was done in air atmosphere. Temperature measurement was made with thermocouples fastened directly to the bend fixture within less than 1 in. from the specimen. Autographic stress-strain curves were recorded during each test, and breaking load, total deflection, and plastic strain could be obtained from these curves. Stress was calculated from the beam formula S = 3PL/2bh2, where P is the load in pounds, L the span in inches, b the specimen width in inches, and h the specimen thickness in inches. This formula is strictly correct only in the elastic range but has been used to calculate a nominal stress for convenience in the plastic range. The stress given is the maximum stress in the specimen. Results The results of the complete series of tests are shown in Table I. The first group of tests (specimens Nos. 1-6) showed the beginning of plastic flow at a test temperature of 900°C, so two additional tests (Nos. 8 and 9) were made at 950°C on small-size specimens from bar No. 2. Specimen No. 8 was tested in the as-machined condition, and No. 9 was heat-treated in hydrogen at 1300°C for 2 hr, cooled to 1200°C and held 1 hr, cooled to 1000°C and held 1 hr, cooled to 900°C and held 1 hr, and finally cooled to a low temperature before removal from the hydrogen. It is apparent that the heat-treatment had a significant effect on yield strength and ductility. In addition, the magnitude of the yield point was conslderably reduced in the heat-treated specimen as is shown m Fig. 1 by tracings of the stress-strain curves. After obtaining a furnace capable of reaching higher temperatures specimens Nos. 10 to 13 were tested at 1100 and 1200°C. Strain rate was increased by up to a factor of 10 to see whether the ductility observed was excessively strain sensitive. Specimen NO. 10, strained at 0.02 ipm and 1100oC, was still bending at a deflection of 0.322 in. when the load rate was increased to 0.2 ipm, resulting in immediate

Jan 1, 1959

By Richard S. McCaffery, Clarence H. Lorig, Joseph F. Oesterle, Ira N. Goff, Oscar O. Fritsche

This paper is the report of an investigation to determine the relations between the viscosity, temperature and composition of that portion of the silica-alumina-lime-magnesia system(l) within which blast-furnace slags are found. The work reported in this paper was made possible by a grant of funds from Engineering Foundation. It is a part of a project, the determination of properties and structure of iron blast-furnace slags, upon which the laboratories of the University of Wisconsin have been at work for some years. Three papers have been published, which have marked the progress of the study of iron blast-furnace slags at Wisconsin. The first,(2) Desul-furizing Power of Iron Blast-furnace Slags, discussed the solubility of sulfur in slags that contained no magnesia and discussed the viscosity. The second, (3) The Constitution of Iron Blast-furnace Slags, developed the constitutions of slags in the four-component system, silica-alumina-lime-magnesia, and pointed out an explanation of slag structure. Composition of Iron Blast-furnace Slags,(l) which was the third paper, gave a method of calculating the percentages of the various compounds present in slags when the amount of oxide was given and also an interpretation of quaternary equilibrium. Illustrations were given of the mineral composition of blast-furnace slags and some applications of composition results were shown. Because of their relative ease of measurement, the viscosity-temperature relation for slags was selected as a factor which would be useful in correlating the physical properties of molten slags to furnace operation. With this in mind the viscosities of slags whose compositions are in that portion of the quaternary system, silica-alumina-lime-magnesia, in which blast-furnace slags occur, were thoroughly investigated.

Jan 1, 1932

By Roy W. Moore

The Tom Reed Extension and Big Jim mines of United Eastern Mining Co. are situated in the Oatman district, Mohave County, Ariz., about 28 miles southwest of Kingman, the nearest railway point. Articles descriptive of the mine surface plant, mill construction, and plant operations have been written by Otto Wartenweiler,' the designing engineer; Wheeler 0. North12 when he was assistant general manager for the company, and Earle M. Bagley, mill superintendent.3 The last article covers average costs for the full time the mill was operated. The geology of the mines is described by F. L. Ransome 4 of the United States Geological Survey. Production was started in January, 1917, and the known orebodies were exhausted in May, 1925, showing a life of seven years and five months. On account of the comparatively short life and the fact that stoping operations were confined to two orebodies, little experimenting was done with mining methods. The two orebodies were in what is generally called the Tom Reed-United Eastern vein, which occupies a fault fissure having a normal displacement of several hundred feet. Seven or eight very productive ore shoots were mined along this vein in a distance of 1 1/2 miles, the two worked by the United Eastern being 1 mile apart. The maximum dimensions of the Tom Reed Extension ore shoot were: height, 750 ft.; length, 950 ft.; thickness, 48 ft. The vein structure varied from a solid quartz-calcite filling to a series of parallel stringers separated by andesite. From this body, 511,976 tons of ore were mined. (Fig. 1.) The maximum dimensions of the Big Jim orebody were: height, 450 ft.; length, 850 ft., thickness, 35 ft. Its structure was similar to that of the Tom Reed Extension but larger sections of the vein were made up

Jan 1, 1928

By M. Safiuddin

Within the mining industry, open-pit mining has progressed to a point where a 200-yard walking dragline is as conceivable today as a 35-yard dragline was just a few years ago. This is possible due to the technological advances and efforts of the excavator manufacturers, and the manufacturers of electrical equipment have always stayed abreast with them in meeting their requirements and in making available their experience with the latest control techniques and hardware from various fields for application in the mining industry. An electrician in the coal mines of Pennsylvania who had not heard the word "thyristor" a few years ago now wonders how the old excavators with Rototrols® and magamps could ever work. The thyristors, transistors and operational amplifiers which were considered too fragile and delicate for a rugged and severe application like the mining industry, today constitute the brain of an excavator control taking commands from the operator and giving signals to the muscles of the excavator to move the bucket within a few seconds. A giant 200-yd bucket filled with overburden moves within seconds of the operator's command. Digging cycles for these excavators range from 40 to 60 sec depending on the swing angle. With these tremendous production capabilities of the excavators, the equipment failures and downtime become very expensive, and the loss of return on large capital investment for such machines becomes intolerable. Even though these failures and downtimes cannot be avoided completely, a good preventive maintenance program can help reduce them, thus increasing the machine availability. As we shall see below, the causes for breakdowns and failures of electrical equipment can be analyzed and a good preventive maintenance program can be drawn up to eliminate most of these failures.

Jan 9, 1967

By Albert H. Fay, William B. Plank

In practically all rock-excavation problem there is need for a careful study of the rock structure, its fault, cleavage or bedding planes, and even the texture of the rock itself. These studies should form the bases upon which an excavation method is selected and they should be carefully considered in predicting the amount and extent of the excavation. The need for such studies was forcibly illustrated in the problems involved in a cut made in 1929, along and underneath a 200-ft. high rock projection for a State highway near the City of Easton, Pennsylvania. The rock mass was badly faulted and also contained a number of cleavage planes at approximately right angles to the fault planes. Much of this structure was visible and could have been studied and analyzed before the work was begun. The State had rigid specifications as to finished grade and slope of cut, which apparently were made without reference to the geologic structure. The contractor complied with the specifications, under the close inspection of the State engineers. A tunnel blast was placed in the base of the cliff, with the result that 65 per cent more rock was broken than was intended by the specifications. About four years after the blast, the writers of this paper studied the circumstances surrounding the operation, to determine the cause of this excess excavation. Scope of Work The section of the roadway involved was about 200 ft. long and on a 6' curve. It was necessary to relocate points on the curve, from which all faults and cleavage planes were located and measured by the use of transit and clinometer. A plan (Fig. 1) showing the blasting tunnel, the roadway, and traces of the faults and cleavage planes on the level of the roadway, was prepared; also 13 cross-sections at varying intervals, showing the original face of the hill and the face after the blast. The original and final profiles of the rock face, taken from the plans of the State engineers, are shown in Figs. 2, 3 and 4.

Jan 1, 1937

By Carl H. Samans

In their recent complete review of the subject of age-hardening,' R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plastically deformed has definitely been established.2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advancing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipitation will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers ('discontinuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation. Crystallography of the Precipitation Process Through the extensive investigation by R. F. Mehl, C. S. Barrett and F. N. Rhines3 on the Widmanstätten structure in aluminum-rich copper

Jan 1, 1940

By Carl H. Samans

In their recent complete review of the subject of age-hardening,' R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plastically deformed has definitely been established.2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advancing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipitation will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers ('discontinuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation. Crystallography of the Precipitation Process Through the extensive investigation by R. F. Mehl, C. S. Barrett and F. N. Rhines3 on the Widmanstätten structure in aluminum-rich copper

Jan 1, 1940

By W. S. Weeks

In coursing the ventilating air through a mine it is often necessary to restrict a comparatively open split in order that it may carry exactly the desired quantity of air. Such a restriction is known as a regulator, and usually takes the form of a partition with a hole in it. The quantity of air circulating is controlled by the size of the hole or orifice. For example, it is desired to force a quantity q I cu. ft, per min. through split a (Fig. 1) and the quantity q2 through split b. It requires a pressure of 2 in. water to force the desired quantity through a, and a pressure of 1 in. to force the desired amount through b. The pressure drop between points A and B must be 2 in and a pressure of 1 in. must be destroyed in split b. This is done by inserting a regulator in b, which causes the velocity to increase in the orifice and results in a change from pressure-head to velocity-head. If the air, after passing the orifice, is slowed down in a turbulent manner, all of the velocity-head does not change back into pressure-head, so a permanent loss of static pressure results. A classic formula for computing the area of an orifice to destroy a certain amount of static pressure has been handed down from early days: 0.0004Q a =2 This formula is based on the assumption that all velocity-head in the orifice is "destroyed;" that is, does not reappear again as either velocity-pressure or static pressure. The derivation of the formula is as follows: h = head lost in regulator in fect of air. v = velocity in regulator in fect per second. q = quantity circulating in cubic feet per second. Q = quantity circulating in cubic feet pcr minute. a = area of orifice in square feet.

Jan 1, 1928

By J. E. Johnson

It is the purpose of the present paper, while not excluding chemical considerations, to deal more extensively with some of the physical and mechanical aspects of the blast-furnace process, and to point out its dependence, in these respects, on well-known laws. The quantity and cost of ore and flux required to make a ton of iron being determined by circumstances over which the furnace-man, under given conditions as to quality and quantity of product, has commonly little control, the principal item of cost, apart from the saving of labor, which he can aspire to reduce, is that of fuel. To determine the limits of possibility in this direction is clearly the first step in a practical inquiry; and this step is represented herewith in Fig. 1, a diagram showing the total useful effect obtained from a pound of fuel under various conditions, and thus permitting direct comparison, under any given conditions, between actual results and the maximum possible results. The following statements will explain the basis upon which this diagram has been constructed. One pound of fuel, containing 90 per cent. of fixed carbon (which represents average conditions), is taken as the unit. The degree of oxidation of the carbon is measured by the ratio of the two oxides of carbon contained in the top-gases. It is necessary to remember that a considerable quantity of carbon is brought in as carbon dioxide by the flux, and to take account of it and of its condition. It is here considered that the carbon dioxide liberated by the limestone does not affect the analysis of the top-gases, and that the ratio of CO to CO2 will remain unchanged by the addition of limestone; enough CO, being reduced by the solution

Jan 1, 1906

By L. G. Westgate

PART I.-AREAL GEOLOGY§ PIOCHE lies 240 mi. southwest of Salt Lake City, in southeastern Nevada, 19 in. west of the Nevada-Utah line. It is at the end of a branch line (33 m.), which connects at Caliente with the Los Angeles and Salt Lake division of the Union Pacific System. Its commercial relations are with Salt Lake City and Los Angeles, chiefly with the former. The surrounding area is part of the Great Basin, an arid region of alternating mountain range and intermont plain, the latter floored with outwash from the mountains. About Pioche the plain varies between 4700 and 6000 ft. above sea level. The town lies in a valley at the east base of a low northwest-southeast range (the Pioche Hills) 12 miles in length, which rises about 1000 ft. above the adjacent flat. West of the. Pioche Hills is a higher north-south range consisting of two parts: to the south the Highland Range, between Bennett Pass and Stampede Gap; to the north the Bristol Range, from Stampede Gap to Bristol Pass. This double range reaches altitudes of 8000 to 9000 ft., or more, (the highest point, Highland Peak, is 9395 ft.) and rises some 2500 ft. above the surrounding plain. It is continued in lower hills to north and south. Smaller ranges rise from the flat west of the Highland and Bristol ranges. The area studied and shown on the map (Fig. 1) is covered by 3 one inch to the-mile topographic sheets: the Highland Range, the. Bristol Range, and the Panaca, the latter mapped in part only. The sedimentary rocks of the district include Paleozoic limestones, sandstones and shales, Pliocene tuffs, and modern wash. Igneous rocks are represented by intrusive dikes and stocks and by extensive lava flows of mid-Tertiary time.

Jan 1, 1927

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way 'to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgC03) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1951

By H. M. Howe

I WISH to present to you a few thoughts on some of the phenomena and laws of iron smelting. Owing to the great complexity of the subject, to the great variety of points to be taken into consideration, many of which are very poorly understood, and to the meagreness and even conflictoriness of our information with regard to some of the most important laws which govern the subject, the fruits of such thoughts as I venture to offer you must be received as speculations, not as facts. Nevertheless, in discussing old phenomena from new standpoints, thus furnishing a metallurgical parallax, if I may say so, these theoretical speculations may have their value in helping to a clearer comprehension of the phenomena and laws we now know, and in suggesting new lines of inquiry. While an increase of height in blast furnaces is not always followed by increase in their power of production, experience proves that it tends to increase it; for while we have many cases of short furnaces producing more iron than longer ones, yet enormous productions, such as those of the Lucy and Isabella furnaces of Pittsburgh, and of the furnaces of Esch sur l'Alzette, in Luxembourg, have never been reached in short furnaces. We may safely infer that height is an element essential to great production, though of course not the only essential element, and that, in the case of high furnaces which are not capable of great production, some other essential element is wanting. Moreover, experience teaches that within limits increase of height tends to increase the producing power in a still higher ratio. Thus, in the Esch furnace, which is 19.8 meters (65 feet) high, 393 tonnes (or 387 gross tons) of 312 per cent. Ore

Jan 1, 1877

By Raymond B. Ladoo, C. A. Stokes

Bruce C. Netschert—It is unfortunate that the authors of this paper consider it necessary to begin with an expression of concern over possible false interpretations of the word "economics." In their preoccupation with the definition of economics, they have adopted a definition of mineral economics which is, to say the least, unduly narrow. Just as the broad field of economics is not confined to a study of the profitability of business concerns, but includes the problems of production, distribution, and consumption as they pertain to society as a whole; so an inclusive definition of mineral economics should not be confined to the determination of the profitability of mineral-producing and processing enterprises, but should include the significance of the unique characteristics of mineral resources as raw materials for the use of society. Such features as the exhaustibility and localized, haphazard occurrence of deposits, the existence of a secondary (scrap) supply, and the increasing cost of operation during the life of a mining enterprise are obviously factors which concern those businesses which are producing mineral raw materials, since they partially determine the profitability of such enterprises. They are also of concern to society as a whole, however, as characteristics of one of the basic elements of the economic system. In the last analysis, the contribution which mineral economics can make as a means of determining and guiding social policy with respect to the production and utilization of mineral resources is perhaps more important than its use as a basis for determining the cost accounting procedure of individual firms. The list of "economic factors peculiar to the industrial minerals" which the authors present is in reality an application of such a broad definition of mineral economics. An inconsistency appears, however, in the inclusion of items 8 and 9 in the list. As this writer sees it, the point in question is: What influences do the characteristics of industrial minerals have on the characteristics and operating procedures of industrial mineral enterprises which are not present in the metallic mineral field? In answering this question with items 8 and 9, Messrs. Ladoo and Stokes do not recognize that there are two distinct types of differences between the two fields of enterprise. There are, on the one hand, important basic economic distinctions due to inherent economic characteristics of industrial minerals which do not pertain to metallic minerals. On the other hand are those characteristics of the industrial mineral enterprises peculiar to them alone, but which are superficial and temporary, in that they may be changed or eliminated at the discretion of the managers of those enterprises. The lack of adequate research and development in industrial mineral production, processing, and marketing (item 8) is not due to an inherent characteristic of industrial minerals. It is true that one may perhaps describe the field of industrial mineral enterprise in terms of such a deficiency, just as one could, until recently, point to a similar lack of research and development in the coal industry; but unless it can be shown that the deficiency has been wholly or partially due to the very nature of industrial minerals themselves it is not an "economic factor peculiar to the industrial minerals" but a temporary characteristic peculiar to the industry. In the writer's opinion, the authors have not demonstrated that the former relationship exists. Similarly, item 9, the "influence of technologic developments," is also not inherently peculiar to industrial minerals. Nowhere in the discussion of this item do the authors mention anything that is not equally applicable to the field of metallic minerals. This is not meant to imply that the specific technologic developments which the authors list are of equal significance in both fields. It does mean that such a statement as, "technological advances together with new consuming areas to provide markets make deposits commercially valuable which once were of no interest" cannot be considered as an argument that technological developments have significance in the field of industrial minerals alone. In considering the problem of stockpiling, the authors note that the stockpiling of nonstrategic materials might be desirable if future wartime needs could exceed domestic production capacity, but dismiss this as hardly adequate to justify such stockpiling. The problem, however, can be stated in broader economic terms, i.e., the real costs (as distinguished from the money costs) of prewar versus wartime production. In other words, it might well be that the labor and capital required to produce a given amount of a certain mineral raw material could be used more efficiently in another industry. In such a case it is obviously advantageous to stockpile the material in prewar times rather than forego the benefits of additional production in another line of endeavor during wartime under conditions which demand the optimum use of all resources, including manpower and capital. To the writer's knowl-

Jan 1, 1951

By Raymond B. Ladoo, C. A. Stokes

Bruce C. Netschert—It is unfortunate that the authors of this paper consider it necessary to begin with an expression of concern over possible false interpretations of the word "economics." In their preoccupation with the definition of economics, they have adopted a definition of mineral economics which is, to say the least, unduly narrow. Just as the broad field of economics is not confined to a study of the profitability of business concerns, but includes the problems of production, distribution, and consumption as they pertain to society as a whole; so an inclusive definition of mineral economics should not be confined to the determination of the profitability of mineral-producing and processing enterprises, but should include the significance of the unique characteristics of mineral resources as raw materials for the use of society. Such features as the exhaustibility and localized, haphazard occurrence of deposits, the existence of a secondary (scrap) supply, and the increasing cost of operation during the life of a mining enterprise are obviously factors which concern those businesses which are producing mineral raw materials, since they partially determine the profitability of such enterprises. They are also of concern to society as a whole, however, as characteristics of one of the basic elements of the economic system. In the last analysis, the contribution which mineral economics can make as a means of determining and guiding social policy with respect to the production and utilization of mineral resources is perhaps more important than its use as a basis for determining the cost accounting procedure of individual firms. The list of "economic factors peculiar to the industrial minerals" which the authors present is in reality an application of such a broad definition of mineral economics. An inconsistency appears, however, in the inclusion of items 8 and 9 in the list. As this writer sees it, the point in question is: What influences do the characteristics of industrial minerals have on the characteristics and operating procedures of industrial mineral enterprises which are not present in the metallic mineral field? In answering this question with items 8 and 9, Messrs. Ladoo and Stokes do not recognize that there are two distinct types of differences between the two fields of enterprise. There are, on the one hand, important basic economic distinctions due to inherent economic characteristics of industrial minerals which do not pertain to metallic minerals. On the other hand are those characteristics of the industrial mineral enterprises peculiar to them alone, but which are superficial and temporary, in that they may be changed or eliminated at the discretion of the managers of those enterprises. The lack of adequate research and development in industrial mineral production, processing, and marketing (item 8) is not due to an inherent characteristic of industrial minerals. It is true that one may perhaps describe the field of industrial mineral enterprise in terms of such a deficiency, just as one could, until recently, point to a similar lack of research and development in the coal industry; but unless it can be shown that the deficiency has been wholly or partially due to the very nature of industrial minerals themselves it is not an "economic factor peculiar to the industrial minerals" but a temporary characteristic peculiar to the industry. In the writer's opinion, the authors have not demonstrated that the former relationship exists. Similarly, item 9, the "influence of technologic developments," is also not inherently peculiar to industrial minerals. Nowhere in the discussion of this item do the authors mention anything that is not equally applicable to the field of metallic minerals. This is not meant to imply that the specific technologic developments which the authors list are of equal significance in both fields. It does mean that such a statement as, "technological advances together with new consuming areas to provide markets make deposits commercially valuable which once were of no interest" cannot be considered as an argument that technological developments have significance in the field of industrial minerals alone. In considering the problem of stockpiling, the authors note that the stockpiling of nonstrategic materials might be desirable if future wartime needs could exceed domestic production capacity, but dismiss this as hardly adequate to justify such stockpiling. The problem, however, can be stated in broader economic terms, i.e., the real costs (as distinguished from the money costs) of prewar versus wartime production. In other words, it might well be that the labor and capital required to produce a given amount of a certain mineral raw material could be used more efficiently in another industry. In such a case it is obviously advantageous to stockpile the material in prewar times rather than forego the benefits of additional production in another line of endeavor during wartime under conditions which demand the optimum use of all resources, including manpower and capital. To the writer's knowl-

Jan 1, 1951

By Albert R. Ledoux

Discussion of the Paper of Albert R. Ledoux, read at the Atlantic City Meeting, February, 1904. ARTHUR JARMAN, Sydney, New South Wales, Australia' (communication to the Secretary*): Some remarks upon. Dr. Ledoux's interesting paper from one who has not visited America may, I hope, be of interest to members. It appears to me that there is considerable difference between the training of the American and of the British mining engineer. Not that the subjects are different, but rather in the way in which they are handled, the illustrations being, as far as possible, mining in character. Colloquial instruction is unknown in English curricula, but could be introduced with advantage. Students here assure me that an hour of conversation is of tar more use to them than an hour of the best lecturing. In England a school-year of 6 or 7 months would be considered very short indeed; but Americans do not consider it so, for the reason that the rest of the year is mostly spent in acquiring practical acquaintance with their subjects in works or in the field, and the shorter courses, when coupled with this large amount of outside expe¬rience, produce an essentially practical-minded engineer, who is also more of a business man; whereas the English system, though excellent from a scholastic point of view, produces the theoretical rather than the practical man. British schools are waking up, however, and the practical aspect of the engineer's training is receiving greater consideration. Once launched upon his career, the American engineer is immediately called upon to exercise his self-reliance and ingenuity, if he is to retain the confidence of his employers; but what can we say of English directors? In how many cases is the engineer allowed to guide the destinies of his company? Witness several recent cases of gross waste of money upon unsuitable plants, and the perpetuation of prehistoric methods of

Mar 1, 1905

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,'' might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938