Search Documents

By R. W. Raymond

PROFESSOR W. P. BLAKE, in a note to his Catalogue of California Minerals, pointed out that the milling districts of the Pacific slope are arranged in parallel zones, following the prevailing direction of the mountain ranges. This interesting generalization has been more frilly illustrated and connected with the geological history of the country by Mr. Clarence King, who sums up the observed phenomena as follows : " The Pacific coast ranges upon the west carry quicksilver, tin, and chromic iron. The next belt is that of the Sierra Nevada and Oregon Cascades, which, upon their west slope, bear two zones, a foot-hill chain of copper mines, and a middle line of gold deposits. These gold veins and the resultant placer mines extend far into Alaska, characterized by the occurrence of gold in quartz, by a small amount of that metal which is entangled in iron sulphurets, and by occupying splits in the upturned metamorphic strata of the Jurassic age. Lying to the east of this zone, along the east base of the Sierras, and stretching southward into Mexico, is a chain of silver mines, containing comparatively little base metal, and frequently included in volcanic rocks. Through Middle Mexico, Arizona, Middle Nevada, and Central Idaho is another line of silver mines, mineralized with complicated association of tli6 base metals, and more often occurring in older rocks. Through New Mexico, Utah, and Western Montana lies another zone of argentiferous galena lodes. To the east, again, the New Mexico, Colorado, Wyoming, and Montana gold belt is an extremely well-defined and continuous chain of deposits." These seven longitudinal zones or chains of mineral deposits must

By T. M. Daulton, Chester F. Lee

The Atlin Mining District is in the northwest corner of the Province of British Columbia. Ruby Creek, where the operation to be described is situated, is 17 miles east of the town of Atlin and about 18 miles south of the south line of Yukon Territory (Fig. 1). Gold was discovered in the district in January, 1898, and the production to date from placer mines has been $4,518,000, according to the reports of the Minister of Mines for the province. Geology The essential points in the regional geology are given in the following paragraphs. Long erosion produced a plane-like surface slightly above sea level with a few peaks and ridges.' A gradual uplift followed and erosion increased, the streams cut deeper, the cuts so made being afterward increased by glaciation. The ice straightened and planed the slopes of the main valleys and widened and lowered their floors, in some cases flooring the valleys with silt, sand, gravel, and clay. As the glaciers rapidly retreated, lakes were formed. As to the origin of the gold, J. C. Gwillim says? "The Surprise granite has been carried northward toward Gladys Lake and Teslin, and the granite of the great plateau on the Taku trail was found in blocks on the opposite range across Hurricane River 10 miles north of its original position. Otherwise there is little evidence of far removed material, the boulders of the lake shore and creek beds being of local appearance. This appears to strengthen the opinion that the placer gold had its origin within the drainage basins where it is now found." In the gold-bearing creeks of the Atlin district there are two "runs"

Jan 1, 1917

By Charles Janin

ONE of the most interesting features of the world's platinum situation has been the steady increase of Russian production, which had dropped to 11,000 oz. in 1920, but increased to 92,000 oz. in 1926, and to probably over 100,000 oz. for 1927. It is ex-pected that Russian production of platinum will, be-fore long, closely equal its pre-war production, or approximately 200,000 oz. annually. The world production before the war was around 250,000 oz.; that for 1925 has been estimated at 160,000 oz., and for 1926 probably 170,000 oz. The consump-tion of platinum has, however, decreased. The esti-mate of the International Selling Agency was a de-mand of 130,000 oz. new platinum against a normal pre-war demand of over 200,000 oz. The high price of platinum during the war gave an added impetus to the search for substitutes for the metal, and sev-eral were developed that are now used extensively in place of platinum. The demand for platinum for high-class jewelry, however, was not greatly affected by the high prices, but "white" gold did replace platinum in the cheaper jewelry. Colombia is the most important producer of plati-num, next to Russia, and the production has increased from around 10,000 oz. pre-war production to 55,000 oz. or more in 1927. In 1924 important discoveries of platinum were made in South Africa. Prior to these discoveries practically all platinum was recovered from alluvial deposits, and the South African opera-tions are first to work an ore profitably for the pri-mary recovery of platinum. A number of companies were formed to develop these deposits, but only a few made any real progress. Total production for 1926 was about 5000 oz. The United States production is unimportant; that in Canada has increased to around 9000 oz., principally as a by-product in nickel-copper ores.

Jan 5, 1928

By Gerard C. Gambs

The electric utility industry is the largest customer of the U.S. coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50[c] to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag.

Jan 1, 1967

By R. S. Bradley

WHAT are known as insulating firebrick are lightweight firebrick with low thermal conductivity designed primarily for use in direct contact with furnace gases. These are a recent development in the refractories industry, and are really an outgrowth of the type of insulating brick suitable for use behind refractory walls developed by the insulation manufacturers. To differentiate between these two types of brick, the manufacturers have recently agreed upon the use of the term "Insulating Firebrick" to apply to the type of brick suited for use in direct contact with furnace gases, and the term "Insulating Brick" for the type suitable for use behind refractory walls. Insulation was applied to steam pipes as far back as 1900. This was a low-temperature insulation, the most common type being magnesia blocks. The next development was applying insulation to the outside of furnace walls, a service which necessitated an insulating material of higher temperature resistance. Natural diatomaceous earth, both in the powdered and brick form, was used; this was efficient and is still used extensively for backing up refractory walls where the inner surface temperature of the insulation does not exceed 1600° F.

Jan 1, 1937

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack.

Jan 1, 1949

By AIME AIME

THE 140th meeting of the Institute will be held in the Engineering societies Building, 'New York, Feb.: 16-19, and one of the most important features, one which cannot be reduced to text in the TRANSACTIONS, will be the opportunity to renew old friendships and make new friends, to talk things over -to orient one's self in these troublous .times. There will be daily get-together luncheons for all, luncheons and dinners for specialized groups, an informal dance, the annual reception and banquet, and a smoker. And such a smoker! It starts with dinner at .dinnertime, shows signs of cabaret, turns smoker, and then goes entertainment-all for the price of one. This year one can stay long after 11 o'clock-there will be time and opportunity to amble around and meet everyone present. The formal program is rapidly rounding into shape. The annual business meeting will -be held on Tuesday morning and the banquet will be at the Commodore. The four Divisions and the various, Technical Committees are arranging their sessions. and scheduling for these a long list of significant papers. A .feature of the meeting will be a number of round tables on timely subjects.

Jan 1, 1931

By R. B. BRINSJIADE

THE following is an attempt to form a formula by which a mine call be quickly evaluated, after all pertinent physical data have been collected from observations on the ground by a competent mining engineer. ASSUMPTIONS. Let G = price to be paid for the mining property. M = cost of developing the mining property to yield y tons of ore daily. P = cost of suitable plant to treat y tons of ore daily. p = value of said plant when the mine has.been exhausted. C = total fixed capital investment. W = working capital investment

Jan 1, 1908

Jan 1, 1881

By C. MeCulloch

A NOVEL practice in the bituminous coal industry is the accelerated method of burning coal to ash used in the laboratory of the Fidelity washery of the United Electric Coal Companies, Du Quoin, Ill. Development of this method has supplanted the tedious float-and-sink process for plant control at this plant. In normal operation the plant operators have available within thirty minutes the accurate ash percentage of the coal loaded in the railroad cars and can therefore make adjustments to maintain a practically uniform quality of washed coal, regardless of the variations in washery feed.

Jan 1, 1937

By AIME AIME

MINERALS and mineral resources are recognized as one of the things that nations are prone to quarrel about. The territory that was arbitrarily incorporated into the Polish Republic after the World War produces a variety of essential minerals on a substantial scale. The accompanying table has been compiled to give some idea of the relative importance of this production. Poland, before the recent war started, had an area of 150,000 sq.mi., just a little larger than the State of Montana. Its population was 32,000,000, equal to that of New York, New Jersey, Pennsylvania, Connecticut, and Massachusetts. Though not a highly industrialized country it nevertheless has important mines, steel plants, petroleum refineries, and sundry metal-fabricating manufactories. Coal, petroleum, iron and steel, zinc, lead, pyrite, potash, and salt are produced in excess of the country's domestic consumption. It has no appreciable production of copper, chromium, tungsten, nickel, tin, mercury, manganese, aluminum, magnesite, fluorspar, or graphite.

Jan 1, 1939

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By Basil B. Zavoico

ALTHOUGH the American petroleum industry was affected by the Second World War from its early beginning it was not until Dec. 7, 1941- that the industry was placed on full war footing. Even throughout most of 1942 the American overseas operations were limited and not until late in the year did expansion of military activities, more particularly the offensive in North Africa, affect the domestic supplies to such an extent that critical deficiencies developed locally in this country, particularly along the East Coast. The definite outlook for greatly expanded offensive operations by the United States on both Atlantic and Pacific fronts makes certain that during 1943 the domestic situation will. not be alleviated; rather it may become even more critical even though additional transportation facilities, now being built and planned. will be completed from the southwestern producing states to the East Coast.

Jan 1, 1943

By F. B. Plummer

PETROLEUM ENGINEERING deals with the production, transportation, and refining of crude oil. Refining is chiefly the work of the chemical engineer; production, that of the petroleum engineer. Production engineering only is discussed in this paper. Petroleum production engineering is closest related to and, in fact, is a branch of mining engineering. Formerly, many petroleum engineers were trained as mining engineers or mining geologists. The profession is related also to mechanical and civil engineering to about the same extent that mining engineering is. Petroleum production draws upon the mechanical branch for drilling and pumping machinery and upon civil engineering for the construction of transportation lines, water supplies, and water-disposal plants. Fundamentally, petroleum production engineering deals with the removal of the oil from the reservoir rocks, just as mining is concerned with the removal of ore. The process of oil production demands a specialized knowledge just as distinct from mechanical and civil engineering as mining is distinct from operating a Diesel engine. Even though the chief tools of the petroleum engineer are the drill and the pump, these may be of little avail, and certainly not efficient, if their selection and use is not based on a knowledge of the physical chemistry of oil, the geology of the formations, the structure of the oil sand, the hydrodynamics of the reservoir, and the interrelation of all these many factors.

Jan 1, 1936

By William B. Plank

ENROLMENT data given in this report of the seventh study of the schools by the Mineral Industry Education Division reveals the critical situation in the mineral engineering schools of the United States. Complete figures for the year 1942-43 show that at that time, about one year after Pearl Harbor, the enrollment of mineral engineers was 6385 or 30 per cent less than in 199441. By October 1943, however, enrollment had dropped to 2050, as reported in the Journal of Engineering Education of January 1944. This was a further reduction of 68 per cent in one year, or 77 per cent in three years. With accelerated programs in effect during the current year, with many graduations since last October, and with the military forces taking practically all the high school graduates, the present enrollment is, of course, much lower than the 2050 above given. There are no late data on the exact situation. In Canada, the same situation exists in the mineral engineering schools, only

Jan 1, 1944

By L. E. Tanner

A study was made of the transformation kinetics of the commercial titanium-base alloys, Ti-2.5Al-16V and Ti-4A1-3Mo-1V, using two different heat treatment cycles: 1) step-quenching to aging temperatures from a ß solution anneal and 2) water-quenching from an a+ß solution anneal followed by reheating to aging temperatures. Metallographic examination and hardness testing provided the major portion of the data, while electrical resistivity, dynamic elastic modulus, and X-ray diffraction techniques were also used to obtain critical or confirnzatory data. TTT diagrams were constructed from these results. The sheet alloys, Ti-2.5Al-16V and Ti-4Al-3Mo-lV, are of current interest to the Department of Defense. As an aid to the planning of their respective heat treatments, a program was carried out to determine the transformation kinetics of these alloys using ß and a + ß reference states. This paper presents the TTT diagrams constructed from data obtained by metallographic examination and hardness testing, as well as by X-ray diffraction, electrical resistivity, and dynamic elastic modulus determinations. EXPERIMENTAL PROCEDURE Materials—Sheets of the alloys were obtained from the producers in the "mill anneal'' condition and were tested prior to shipment to assure their meeting mill specifications. Chemical analyses were also supplied and are presented in Table I. Heat Treatment—The majority of the data presented in this study were obtained from hardness testing and metallographic examination. Sample coupons were cut from the alloy sheets and heat treated on a mass scale. The annealing cycles were operated in the following manner: 1) The ß solution anneals were carried out in a horizontal tube furnace with the bare samples protected by a dynamic helium atmosphere. Following this treatment, the samples were quickly transferred to lead, solder, or oil-bath furnaces for aging. After prescribed times at the various reaction temperatures they were water-quenched. 2) The second cycle simulated commercial practice, which requires the alloys be quenched to room temperature following the a + ß sotution anneal. This anneal was carried out in a muffle furnace with a dynamic helium atmosphere. The specimens were then reheated from room temperature to the reaction temperatures in lead, solder, or oil-bath furnaces, followed by water-quenching after prescribed times at these temperatures. Information concerning the critical temperatures of the alloys was obtained from the literature and solution treatments were based on these values. A summary of the solution annealing treatments is found in Tables II and 111. The aging temperatures for the (a - ß alloys ranged in 50°C intervals from 200°C (392oF) to approximately 50°C below the ß/a + ß transus in the first cycle and approximately 50°C below the a + ß solution temperature in the second. The transformations in these alloys were known to be rather rapid, and thus aging times started at 0.5 min and went to a maximum of 7000 min. Hardness Testing and Metallographic Preparation— Heat-treated samples were sheared and mounted in Bakelite with their cut edges exposed. After a flat surface was ground, the hardness was determined in Vpn on an Armstrong-Vickers machine utilizing a 20-kg load. Three to four impressions were made on each specimen. After this procedure, the hardness impressions were removed and the edge surfaces of the specimens were prepared for metallographic examination in the usual manner. The etchant was 20 pct HF and 20 pct HNO3 in glycerine. Electrical Resistivity—It has been shown that the isothermal reactions in titanium-base alloys can be followed by measuring the changes in e1etrical resistivity attending these transformations. As mentioned earlier, the reaction kinetics of a-ß alloys are rather rapid; thus, it would be expected that resistivity data obtained from these alloys would be more significant if measurements were made continuously at the respective aging temperatures. To accomplish this end a special apparatus, based on the current-potential principle, was assembled. Its design was derived from earlier devices constructed by Colner and zmeska1 4 and Levinson.5 The set-up provided for the heat treatment zof machined specimens (approximately 2 x l0-4in. in cross section by 3 in. in length) and the determination of their relative

Jan 1, 1962

By J. S. Pascover, J. K. Abraham

The influence of the early stages of precipitation on the kinetics and structure of martensite formation in Fe-27Ni and Fe-29.5Ni alloys containing from 0 to 10 pct Ti was examined with X-ray and electron microscopy techniques. The formation of a coherent, ordered preprecipitate had a profound stabilizing effect on the austenite. The Ms was decreased by increased titanium content and aging time up to a critical time. When the critical aging time was exceeded, the Ms was observed to increase markedly. The formation of the clusters was insuppressible and the volume fraction of clusters formed during the quench was a function of the titanium content. Martensite resulting from transformation of the clustered austenite is tetragonal with the c/a ratio increasing with titanium content. A model for the tetragonality is suggested. The morphology and substructure of the m artensite is inter-preted in terms of the above information and the cur-rent models of twinned martensite. ThE ramifications of precipitation in austenite to the properties of austenite have been the subject of numerous investigations. The current research is concerned with the influence of precipitation in austenite on the kinetics and structure of subsequent marten-site formation. In a previous investigation, Abraham et al.1 followed the aging reaction in an Fe-29.5Ni-4.2Ti* (at. pct) alloy using an X-ray diffraction technique. This technique, employing a Guinier camera, provided kinetic measurements through observation of the side band position as a function of aging time. The salient results of this work were: 1) The initiation of precipitation was not suppressed by quenching, i.e., there was a finite cluster zone size at zero aging time; and 2) The hardness of the aged austenite correlated extremely well with the zone size. During the previous work it was noted that the mar-tensite formed after aging was tetragonal, substanti-ating an earlier observation.2 Systematic investiga-tion revealed that the martensite was tetragonal in both the solution-treated then quenched, and the solu-tion-treated, aged, and quenched condition, and, furthermore, that a marked stabilization of the austenite occurred as a function of aging time. The present work is concerned with documenting the tetragonality and the stabilization phenomena as well as the ob- served microstruction with a suggested rationale for the behavior noted. EXPERIMENTAL PROCEDURE The compositions of the alloys are listed in Table I. The analyses were performed after the solution treatment of the strip material. Nickel was determined using the standard dimethy1-glyoxime procedure whereas titanium was determined colorimetrically with hydrogen peroxide and volumetrically by titrating with ferric iron. The materials were melted in a 5-lb vacuum induction furnace, cast into 2-in.-diam ingots, and forged in a temperature range of 950. to 1200°C to 1/2-in. slabs. The three higher titanium containing materials cracked during forging; therefore, to get the alloys into strip form, slices 1/8 in. thick were cut from the slab, homogenized 4 hr at 1150°C, then cold-rolled to a 0.04-in. thickness. The remaining slabs were hot-rolled, homogenized 4 hr at 1065"C, then cold-rolled to a final thickness of 0.03 in. All of the heat treatments were performed under a protective atmosphere of argon. The Ms temperature for most of the alloys is below room temperature; therefore, it was possible to solution treat, quench to room temperature, polish, and then observe the transformation optically on a cold-stage microscope. To determine the effect of aus-tenitizing temperature on Ms, eight of the alloys were treated at two temperatures, 1025" and 1120°C. No measurable variations in Ms were noticed. The remaining alloys were treated at 1025°C. The specimens, : by 5/16 by 0.03 in., were austeni-tized in a vertical tube furnace under a dynamic argon atmosphere. The bottom of the tube was submerged in water for quenching purposes. The question of stabilization that may be operating at room temperature was investigated and found to be negligible. Many of the specimens were held at room

Jan 1, 1970

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By W. D. Ludemann, J. E. Dor, L. A. Shepard

Recovery of the creep resistance of 99.99 pct pure Al was studied at temperatures 540°, 573°, 600°, and 611°K. Poly-crystalline specimens crept under a stress of 950 psi to a strain of 5.5 pct were allowed to recover for periods of from 1 min to 16 days under a residual stress of 4.4 psi. Increased creep rates upon reapplication of the 950 psi stress evidenced softening of the material. The activation energy for the recovery process was found to be 64,000 cal-per mol. THREE major observations have clearly revealed that the creep of polycrystalline aluminum above about 510°K is controlled by the rate of climb of jogged edge components of dislocations past the barriers impeding their motion: 1) Extensive polygonization, characteristic of climb, takes place during creep.'9' 2) The activation energy for creep equals the estimated activation for self-diffusion. 3) The stress law for creep coincides with theoretical predictions based on the climb mechanism.4,5 The decreasing rate during the primary stage of creep must be ascribed to the introduction of additional barriers to the glide of dislocations. During secondary creep the density of barriers must remain constant, the rate at which new barriers are formed being equal to the rate at which they recover. For this reason the nature of the barriers, and their rates of formation and recovery, are significant to a complete understanding of creep. It is proposed here to study the kinetics of the recovery of barriers to creep of high-purity polycrystalline aluminum in the climb range. The technique will consist of creeping a series of tensile specimens under a prescribed stress to given state following which the specimens will be recovered for various times and temperatures under approximately zero stress. The amount of recovery will be determined by comparing creep curves following the recovery. EXPERIMENTAL PROCEDURE The material used for this investigation was a 99.99 pct pure Al supplied by the Aluminum Co. of America in sheets of 0.001-in. thickness having an H-18 temper. The spectroscopic analysis of impurities gave Cu-0.004 wt pct, Fe-0.002 pct, Si-0.001 pct, others-0.000 pct. Creep specimens were machined with their tensile axes in the rolling direction of the sheets. Annealing in a molten potassium nitrate-potassium nitrite bath for 1 hr at 686K, followed by air-cooling, resulted in a grain diameter of from 0.22 to 0.27 mm. Creep machines were equipped with constant stress lever arms of the type suggested by Fullman, Carreker, and Fishher,' which maintained the applied stress to within 0.04 pct of the reported value of 950 psi. Creep strains were calculated from extensions over a 6-in. gage section to the nearest 3 X 10"5. The temperatures of testing, 540°, 573", 600°, and 611°K, were obtained by immersing the specimen and extensometer assembly in a molten KNO2-KNO3 bath. Temperatures during the periods of creeping could be maintained constant to within better than ± 1°K. Correlation of creep data at different temperatures of testing demanded the use of an appropriate temperature-compensated time 8. Previous investigations have shown that the creep of pure metals at temperatures above about 0.55 of their melting temperatures can be correlated by the functional relationship3" e=f(0), s= const. [1] where e = total plastic strain during creep f = a function that depends on stress a = stress 6 = te-Q/RT = a temperature-compensated time t = time under test Q = 35,500 cal per mol = activation energy for creep R = gas constant, and T = absolute temperature In the present series of tests all of the creep was conducted under the same stress of 950 psi. To provide identical initial conditions for the recovery all specimens were first crept to a temperature-compensated time of = 47 X 10-14 min which resulted in a creep strain of 0.055 + 0.005 regardless of the creep temperature. During recovery, a small stress (4.4 psi) was permitted to remain upon the specimens to maintain tautness in the pulling assembly and to prevent mechanical damage to the soft specimen. After each recovery period, the full stress was reapplied and

Jan 1, 1961

By Nicholas J. Grant, A. W. Mullendore, Paul Predecki

The Duwez technique of splat cooling in which a molten droplet of metal is accelerated and made to impact on a cold, highly conducting substrate was investigated.- An apparatus for producing "splat" was constructed employing an explosive powder charge to accelerate the molten metal. Transport of the molten metal just prior to impact with the substrate was studied by means of high-speed photography. The molten particles are small spherical droplets from about 1 to 50 µ diameter. The average cooling rates for aluminum, silver, and a gold alloy splatted on nickel substrates at room temperature were determined experimentally and were found to vary from 18 to 5 x 10' C per sec. The heat-transfer coeficients for pure aluminum and pure silver splats cooled on nickel substrates at room temperature were found to be 2.7 to 6.8 and 13.6 to 54.2 cal per sec sq cm 'C (2 to 5 x 104 and 1 to 4 x 18 Btu per hr sq ft OF), respectively. Solidification rates in pure aluminum and silver splats were calculated. "SPLAT cooling" is a term describing a technique for extremely rapid freezing and cooling of molten metals and alloys to room temperature or below. The technique was developed by Duwez et al.' in 1960, and after refinement2 consisted in transferring a few tenths of a gram of molten metal to near sonic velocity to strike a suitably placed cold copper surface. Upon impact, the metal spread into a thin nonuniform film called a splat, about 10-4 cm thick. The splat particles produced in this manner were thin enough in some areas to be suitable for transmission electron microscopy, without further treatment, and, together with X-ray data, yielded a variety of structures which would be classified as follows: 1) supersaturated solid solutions (increase in solubility limit), 2) metastable crystalline stoichiometric and non-stoichiometric intermediate phases ( in Au-20.5 at. pct Si and in Au-14 at. pct Sb, respectively), 3) amorphous alloys, 4) retained high-temperature phases, 5) alloys having equilibrium phases present, but with unusual, markedly altered structures. The crystalline phases present in splats were usually extremely fine-grained and had low dislocation densities. Present interest in splat cooling centers around a study of the unusual structures produced by the technique, their contribution to alloy theory, and the possibility of the development of new or unusual properties. In addition, the technique is being examined for the production of bulk quantities of new high-strength alloys for low- and high-temperature use. Although a number of alloy systems have already been investigated by the technique, relatively little is known about the mechanism of splat formation and the physical conditions encountered by the metal during solidification and cooling. The purpose of this work was: 1) to determine the velocity, shape, and size of the molten metal droplets just prior to impact with the cold substrate; 2) to try to estimate or measure solidification rates, heat-transfer coefficients, and cooling rates in splats. EXPERIMENTAL TECHNIQUE Splatting Apparatus and Procedure. An apparatus similar to the type originated by Duwez et a1.,2 but employing an explosive charge to accelerate the molten metal, was used. A "Ramset" fastening tool (a gun normally used for driving studs into concrete, steel, and so forth) was mounted vertically above a resistance-heated graphite crucible as shown schematically in Fig. 1. A splat product was produced by melting a few tenths of a gram of metal at the position shown in Fig. 1, and then exploding a powder charge in the breach. The shock wave thus generated traveled down the barrel into the furnace, ejecting the molten metal through the 0.06-in.-diameter hole at the bottom of the crucible. The ejected metal was impacted on a high-conductivity metallic substrate where it formed a splat. High-Speed silhouette Photography. In order to investigate the size and shape of the ejected, molten metal just prior to impact with the cold substrate, high-speed silhouette photographs were taken, and are shown in Figs. 2 and 3. These photographs were obtained with the aid of an Edger-ton, Germeshausen, and Grier microflash unit and a submicrosecond flash drive equipped with a variable time delay. Two types of triggers were

Jan 1, 1965