Search Documents

By Carroll F. Hardy

The day by day loss of industrial plants to gas and oil is chiefly by default. The coal industry is not selling its superior economy, safety, and other advantages to its customers. THE position of the coal industry has been affected by a wide variety of developments in the production and use of energy. The tempo of development and change has been increasing and the end is not in sight. Legislation is currently being proposed for commercial use of atomic power, and the employment of atomic energy in significant quantity will probably occur about the same time as the decline in production of petroleum and natural gas. But these developments are in the future and have little immediate effect on utilization and marketing of coal. While no one should try to suppress or retard the development of a new and economical source of energy, both the coal and private utility industry should be allowed to question how the nuclear power is to be used, who is to use it, and who is going to pay for it. The taxpayers have a monopoly on fissionable material and the knowledge to employ it. Any commercial use must stem from this source. It is not hard to visualize either taxpayer-subsidized private utility atomic power plants on one hand and super TVA's on the other. In view of the gains of gas and oil in the home heating field, it is interesting to compare the 1940 and 1950 census reports on the kind of fuel used for heating in occupied dwelling units. Table I shows that whereas coal provided 77 pct of the fuel for central heating (furnaces and boilers) in 1940, it was down to 45.4 pct in 1950. However, only about 1 1½ million units were lost in this 10-year period. In the non-central heating category, which principally includes stoves, the percentage declined from 39.2 to 25.6, but the units declined about 2½ million in number. The big increase was in heating units designed to burn gas and oil. Use of wood for central heating declined about one-third. Data on amount of fuels used for residential heating are not available, but information is on hand for residential and comnlercial space heating, see Table 11. Commercial space heating includes office buildings, churches, schools. and similar structures. The annual use of bituminous coal in these two categories declined about 1 million tons in the 10-year period. Other forms of solid fuel showed greater losses, except wood, which remained the same. Domestic stokers reached their high point in 1948 with about 1,200,000 in use. At the end of 1951 there were approximately 1,116,790 stokers in use. Conversions to gas and oil have been from hand-fired heating plants in the ratio of about 7 to 1 compared to stokers. In other words, for every one stoker which has been converted to gas or oil, seven hand-fired units have been converted to gas or oil. A bare recital of these data would indicate that the coal industry is holding its own reasonably well. However, 93.4 pct of the new homes built in 1951 were heated by gas or oil. Oil-burning equipment was installed in 37.8 pct and gas equipment in 55.6 pct of the new homes. This indicates that the public prefers gas when it is available, and that oil is second choice, with all forms of solid fuel apparently used when it is unavoidable. It must be pointed out, however, that during the period of rapid expansion of gas pipelines gas has been sold for house heating at prices that are in some cases actually lower than coal prices, or very nearly on a par. Gas has been sold at wells at far below the comparable price for oil produced from the same wells, and far below its actual worth. This situation is being remedied at the present time by increases in gas prices at the wells. For example, the wellhead price of gas in Texas averaged 7.494 per Mcf in 1952. In 1949 it was 4.59c per Mcf. This increase in price is being reflected in pipeline gas prices, and in most of the markets served by the pipelines the tendency is to get it out of the bargain basement type of sales. The American Gas Association estimates that at the end of 1952 there were in the United States about 11 million customers for gas house-heating, and the Association expects additional gains each year until around 18 million homes will be heated by gas in 1975. By 1975 there should be 60 million dwelling units to be heated in the United States, if dwelling units increase at the same rate as the population. If the gas industry heats 18 million dwelling units by that time, this still leaves 42 million units to be heated by some other fuel. If oil is used to heat 18 million dwelling units in that same year, 24 million would of necessity be heated by coal, coke, wood, electricity, or another fuel. The total number of dwelling units using coal listed in the 1950 Census was 18,776,000, so it would appear that coal has a chance at least to stand still in the tonnage sold for domestic use. In the first quarter of 1953, 2044 domestic stokers

Jan 1, 1955

By James R. Stuart

AS the available remaining properties of iron ore reserves on the Mesabi Range are opened up for mining, the various properties located under lake beds are brought nearer an active status. The actual physical problems involved in stripping these properties do not act as a deterrent so much as the legal and political problems that are encountered. When it is proposed to destroy a natural lake that has been used by the public for many years, much local as well as state opposition may be encountered regarding its destruction. Public hearings must be held and some adverse publicity is likely to result. The ownership of the ore under the lake and the rights of the abutting property owners must be settled, and protection from damage caused by a disturbance in surface and subsurface drainage is likely to be demanded by property owners some distance from the proposed mine area. The Embarrass Mine, located near Biwabik, Minn., falls into this classification. A portion of the orebody lies under what was formerly Syracuse Lake, this body of water having been removed in the process of stripping the mine. An additional problem in the case of a meandered body of water is the establishment of a meander line that can be projected downward as mining progresses to form the basis for a satisfactory division between lake bed and upland ore shipments for royalty purposes. Fig. 1 illustrates the complications encountered in maintaining these divisions. A balance point was agreed upon in the center of the lake to make an equable division of lake bed ore to the abutting properties. The entire lake bed has since been adjudged the property of Minnesota. Lake Characteristics Lake bed stripping problems with which this paper is concerned necessarily are limited to a specific type of lake, namely the glacial lakes of the Lake Superior region. One characteristic common to these bodies of water is a deposit of fine black mud or silt on the bottom, frequently underlain by a layer of impervious blue clay. This is also true of the muskeg areas of the region, which present almost identical problems as lakes in stripping. The actual removal of the water and the lake bed material is a routine matter more or less standardized as to equipment, and the period of time required can be estimated easily on the basis of volume and capacity. More important than the foregoing is the execution of preliminary work, and above all, the timing involved. An account could be prepared based entirely on statistical and cost data which would give a very fair picture of the time required and cash outlay needed to effect the removal of a body of water preliminary to stripping the orebody. However, the real interest from the standpoint of the operator and the engineer who carry responsibility for completion of the job lies in the unexpected emergencies and the action of various materials involved in the stripping when the balance has been upset through diversion of water courses and the reduction of the lake level. Runoff and Drainage Lakes are located in natural basins that catch all the rain water and runoff water for a considerable area. Where a lake is involved having an inlet and outlet or a sizeable water course running through it, the drainage area may include a watershed covering many square miles. All available data then must be collected to supply a history extending over as many years for which information can be gathered on the flow of streams, annual rain and snowfall, and most important, the peak flows to be expected. Where the diversion of a stream around the stripping area is a part of the problem, this last factor is of great importance since it controls the cross-section to be selected for the diversion channel and the volume to be removed in its excavation, as well as affecting the hydraulic considerations to be met in the design of the completed channel. Characteristic material in the overburden found at the Embarrass Mine is illustrated in Fig. 2. Well Pumping Pumping from the well holes was started well in advance of the draining of the lake. Fig. 3 shows a gradual lowering of the water table with no noticeable fluctuations during the period in which the lake was being dewatered. Unfortunately, because of tight ground, a maximum flow to the wells was not maintained. This retarded the rate at which the water table was reduced so that in the course of stripping the excavation soon extended below the water table, and the great bulk of the pumping was handled from a system of sumps in the pit itself. Any dewatering program projected by prepumping from wells, a glorified well point system, would have to be started well in advance of the stripping to be of any great advantage. Preliminary drainage of the surface over the mine area is entirely apart from the actual elimination of the lake bed itself. Since the lake is what is called a perched water table because of the impervious character of the lake bottom, the adjoining surface may be dewatered below the surface of the existing lake and the flow will not be affected by the proximity of that body of water. This condition actually has been demonstrated through the establishment of a number of observation holes where a small churn drill was used to put down the holes and a 3-in. pipe was installed for taking water level

Jan 1, 1952

By R. S. Shoemaker, R. M. Darrah

Expanded markets for copper in the past few years and a consequent search for new ore bodies have revitalized the widely known but seldom applied method of producing copper called heap leaching. Heap leaching is defined here as the process applied to oxide ores which have been mined solely for the purpose of leaching. In this case, all costs of mining the ore become a part (and a substantial one, as will be shown) of the cost of the copper produced, whereas in dump leaching the mining cost has already been accounted for as a stripping cost for the sulfide ore. Of course, with newly opened ore bodies, stripping costs may be divided through accounting procedures, between the copper produced by the mill and that obtained by leaching, but in general this type of operation must be economic on the basis of the sulfide ore alone. Heap Leaching Requires Low Capitalization Heap leaching, as a beneficiation method, is unique in that it is the only process used for the recovery of a metal in which the time involved from mining the ore to metal production is measured in months instead of hours or at the most, days. Then too, after the ore body has been depleted and mining has ceased, metal production will continue for some substantial period of time. Heap leaching is also unique because unlike any other method of beneficiation, metal recovery cannot be accurately forecast ahead of time and recovery will never approach that of a conventionally milled sulfide ore or even that of a vat leached oxide ore. Counter-balancing this drawback, however, is the relatively low capital expenditure necessary to put a heap leaching operation into production and the consequence that smaller ore bodies which would not support the higher capital cost involved in a vat leaching plant can be made into producers. Stated more simply, in heap leaching the operator accepts low recovery in exchange for low capital costs and low break even point. Whether the operator chooses vat leaching with its higher recovery and higher capital costs, is a mater of economics which depends in part on the nature of the ore to decide. For instance, an ore that will vat leach in 7 to 10 days using 7 pounds of sulfuric acid per pound of copper produced might use double or triple that amount of acid during the months that are required for heap leaching.

Jan 12, 1968

By GEORGE D. RAMSAY

ABOUT three miles west of Fontana San Bernardino County, California, and fifty miles east of Los Angeles, the Kaiser Co., Inc., has built an integrated steel plant. By integrated, I mean that from its wholly owned iron ore and coal supply, the Kaiser Co. is producing in its own mills iron and steel products. Pig iron to meet the West Coast needs has been produced at Fontana since Jan. 1, 1943; steel ingots were first poured there May 14, 1943; and steel plate for ships was first rolled Aug. 15, just sixteen months after ground was broken. Briefly, the plant consists of: (I) Two batteries of by-product coke ovens, totalling ninety ovens, carbonizing about 1740 tons of coal per day at capacity; with by-product facilities for the production of tar, ammonia, and ammonium suIphate, light oil distillates, and tar distillates. (2) One blast furnace producing at

Jan 1, 1944

Henry D. Hibbard, New York City (communication to the Secretary): The title of Mr. Sargent's paper is somewhat misleading, since the paper itself relates chiefly to various kinds of annealing and their effects, and in very small part only to heat-treatment proper. This term has a well-defined meaning in steel metallurgf, and always includes a rate of cooling faster than the material treated would have in the open air. In bringing about this accelerated rate of cooling, some medium other than air at rest is brought into contact with the heated steel. Usually a liquid (almost always either oil or water) is employed ; but for certain steels a blast of air, and for others an easily fusible or soft metal, such as led (either solid or melted), may be used. Heat-treatment usually includes also subsequent moderate heating, followed, it may be, with another accelerated cooling.

Jan 1, 1902

By D. L. Blakeman, Trimble. J. W., S. W. Banning

Noranda's Grey Eagle mine and mill, in the Siskiyou Mountains of northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mineralogy, milling, and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1986

By H. C. Chang, N. J. Grant

REEP studies and measurements in most in-V> stances are based on a relatively gross gage length. Even in some recent theoretical studies on the mechanism of creep, changes were followed by means of X-rays and metallography without regard for the behavior of the individual grains and grain boundaries.'" Analytical studies of creep have frequently indicated that more than one competing process is operative and that the ultimate creep performance depends on the effects of temperature, time, and strain rate as well as grain size.'-" he grains and grain boundaries are known to respond differently to these variables but the extent of the response is still little known, especially in poly-crystalline materials where the relative orientations of grains and grain boundaries are important. This paper reports some experimental observations of the behavior of the grain boundaries and their effect on the deformation in the grains. High purity aluminum was used to avoid complications of aging reactions, second phase, inclusions, etc. Experimental Procedure A small vertical nichrome wound furnace was built to permit direct loading on the test specimen. This furnace is capable of operating up to about 1300°F with reasonable temperature distribution. A ground rectangular quartz window, 1.25x0.5 in., is imbedded in the external stainless steel tube to permit observations of the creep process with a microscope. An argon atmosphere ,was provided to prevent oxidation. The quartz window caused a temperature gradient between the back and front surfaces of the specimen of 15" at 700°F. The temperature gradient could be cut down to 3°F along the length of the specimen by adjusting shunts across the furnace windings. An ordinary metallurgical microscope with a working distance of 14 mm was rebuilt so that it could be moved in three mutual perpendicular directions. Visual examination could be made with either a 30X eyepiece or a 15X filar eyepiece. Using an objective of focal length 24.3 mm and a numerical aperture 0.20 a total magnification of 120X or 240X could be obtained. High purity aluminum rated at 99.995 pct was supplied by the Aluminum Co. of America as % in. then the gage portion was further machined to 3/16 in. diam. The ends were Y4 in. diam and threaded to fit available specimen holders. Two opposite flat surfaces of the gage portion were obtained by milling, giving final dimensions of the gage portion of 3/4x3/16x3/32 in. Machined specimens were first electropolished in Jacquet's solution.' Reference marks were produced by pressing a thin sewing needle into the surface of the specimen. The specimen was then annealed at 900°F for 24 hr and at 1150°F for 12 hr. Typical macrostructures of specimens treated in this manner are shown in Fig. 1. The range of the grain size was 1 to 5.5 mm (see Fig. l), but most of the grains were of 2.5 mm and went through the whole thickness of the specimen. The specimen was re-electropolished and etched electrolytically to reveal the grain boundaries. In order to reveal the orientation difference of the grains, etch pits were produced on the surface of the grains by etching in a mixture of hydrochloric and nitric acids (HC1, 45 pct; HNO,, 10 pct; H,O, 45 , by volume). The specimens were very carefully put into the holders and furnace; yet even with this care, fine slip lines were developed on the specimen surface.

Jan 1, 1953

By Robert A. Rapp, Jan E. Verfurth

From the measurement of internal-oxidation band widths in Ag-In and Cu-A1 alloys, products for the solubility No and the diffusivity Do of oxygen in silver and apparent NODo products in copper have been obtained over a range of temperature. The NODO products for silver are in agreement with the product of the individually determined No and Do values of Eichenauer and Müller. Although interstitial diffusion of oxygen in silver is expected, the temperature-independent factor Do of the diffusion coefficient does not agree well with the theory of Wert and Zener. For Cu-A1 alloys internal oxidation does not follow the expression derived for ideal kinetics, since the apparent NODo product calculated from internal-oxidation measurements is a function of the alloy content in the specimen. Thus, unequivocal values for No or DO or even the product NODO in copper are not available from the literature. RELIABLE values for the saturation solubility NO and diffusivity DO of oxygen in fcc metals are lacking and difficult to determine, partially because internal-friction measurements are not applicable. Permeability experiments and Sieverts7-type adsorption -desorption methods3 have met with difficulty; however, Eichenauer and Müller4 have recently reported on the solubility and diffusivity of oxygen in silver as determined by the latter technique . Rhines, Johnson, and Anderson,5 and independently Meijering and Druyvesteyn,' introduced the possibility of deriving values for the product NODO in a metal from measurements of the widths of internal-oxidation zones (subscales) formed during the internal oxidation of alloys. In addition to these authors, several other investigators7-9 have made such measurements in various silver and copper alloys at various temperatures, mostly using me- chanically polished specimen surfaces. The purpose of this investigation was to determine over a range of temperature the calculated products NODO in silver and copper from systematic measurements of the widths of internally oxidized zones in Ag-In and Cu-A1 alloys, using specimens with electro-etched surfaces. Consider the internal oxidation of a dilute solid-solution alloy in which the base metal is not oxidized. If diffusion of oxygen is the rate-controlling step, then the depth 5 of the internal-oxidation zone is given by where y is a dimensionless parameter and t the oxidation time. Based on the solution of the diffusion equation, wagnerl0 has shown that under certain conditions several mathematical simplifications may be used in the evaluation of y, so that Eq. [I] may be expressed for the case that y « 1, and y(Do/DB) 1, where N(so)the is the equilibrium solubility (mole fraction) of oxygen in the solvent metal for the given oxidizing atmosphere, is the mole fraction of the solute metal in the bulk alloy, 4 is the diffusivity of the solute in the base metal, and v is the ratio of oxygen atoms to solute atoms in the precipitated oxide BO,. Rearranging Eq. [2] Maak' has derived an expression analogous to Eq. [3] for the case that an external-oxide scale, in addition to an internal-oxidation zone, is formed. For this combined external and internal oxidation for the case that 5/2 where 5 is the distance of the internal-oxidation front from the original external s.urface, and X is the distance of the external oxide/metal interface from the original external interface. The function F is defined by the expression

Jan 1, 1964

By Oscar M. Wicken

The mineral magnesite (MgCO3) if pure would consist of 47.7 pct MgO and 52.3 pct CO2. It is one of the calcite group of rhombohedral carbonates which includes calcite (CaCO3), siderite (FeCO3), rhodocrosite (MnCO3), and smithsonite (ZnCO3) among others. The members of this group enter into a wide range of substitutional solid solutions, whose range is still imperfectly known.* MgCO3 and FeCO3 appear to form a complete series of which breunnerite (ferroan magnesite) is a well known variety. Because of the considerable difference in size of the Ca and Mg ions, there is only a limited range in substitution in the MgCO3-CaCO3 series. (Dolomite, not strictly a member of the calcite group, may be regarded as an ordered structure developed when Ca: Mg is approximately 1:1.) The practical consequence of these relationships is that the lime carbonates (calcite and dolomite) are commonly present in magnesite deposits chiefly as mechanical mixtures. Magnesite may be either crystalline or "amorphous" (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black through shades of yellow, blue, red or gray. It is rarely found pure but generally contains variable amounts of iron, lime, and silicate minerals. Color cannot be used as an index of purity except under specific local conditions in a single quarry. In a given quarry an experienced man may be able roughly to grade magnesite by intuitively assessing such features as crystallinity and color. Crystalline magnesite occurs in larger deposits, but the cryptocrystalline variety is more common. The latter is fine-grained and compact and shows no cleavage; often it is descriptively called "bone magnesite." The fracture is usually conchoidal, and hardness is 3.5 to 5.0. It is normally white, but sometimes it is light yellow to orange or buff because of included impurities. In addition to lime and iron, which may be present in small amounts, silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. In general, commercial deposits of "amorphous" magnesite have lesser amounts of accessory minerals than does crystalline magnesite. The specific gravity of "amorphous" magnesite is 2.90 to 3.0. Pure, crystalline magnesite has a specific gravity of 3.02, but iron carbonate, commonly present, raises the specific gravity to somewhat higher values. Magnesite dissociates, when sufficiently heated, into magnesia (MgO) and carbon dioxide. Either simultaneously or upon further heating the magnesia develops a crystalline structure identical with that of the natural mineral, periclase, which occurs sparingly in nature but not normally in workable deposits. Brucite is another magnesium mineral capable of being directly reduced to magnesia by heat alone. Brucite (Mg(OH)2) has been mined for the production of various grades of magnesia. It theoretically contains 69.1 pct MgO and 30.9 pct H2O. It may be white, but is generally blue or green with a gray cast. It has a translucent appearance. The mineral is soft (hardness, 2.5), and has a specific gravity of about 2.4. Nomenclature of Products The word "magnesite" literally refers to the natural mineral, but common usage has applied it plus a prefatory word to two other

Jan 1, 1960

By M. Garfinkle, W. D. Klopp, W. R. Witzke

The tensile properties of binary W-Re alloys containing up to 33 at. pct Re were determined at temperatures from 78" to 3630°F. Elongations as high as 260 pct were observed in electron-beam-melted tungsten containing 23 at. pct Re when tensile-tested at 3630°F after a 1-hr anneal at 3090°F. All alloys tested under these conditions with rhenium contents between 20 and 28 at. pct exhibited elongations of at least 200 pct. These alloys also showed enhanced grain growth rates. The values of strain-rate sensitivity ranged between 0.2 and 0.3 for the alloys exhibiting high elongations. Houlezler, for swaged alloys tested just above the re-crystallization temperature, strain-rate sensitivities as high as 0.8 were observed. The high-temperature strengths of the high-rhenium-content alloys were also less than those of alloys with intermediate rhenium contents. ALLOYING with rhenium has two distinct effects on the mechanical properties of tungsten. One effect occurs in dilute solid solutions and is most clearly seen in the lowering of the hardness and of the ductile-brittle transition temperature at about 5 at. pct Re.1-3 The second effect occurs in the concentrated solid solution at about 25 at. pct Re, and is characterized by twinning and a larger decrease in the ductile-brittle transition temperature. An aspect of the high-rhenium-content alloy which has received little attention is the higher-than-usual tensile ductility at 3500°F.3 Anomalous high ductility has been observed in several other alloy systems. usually associated with a phase transformation or a solid-solubility limit.4'5 The phenomenon is now commonly termed superplasticity. High-strain-rate sensitivities6 and grain boundary sliding7 have been reported for materials that undergo superplastic deformation. Also, it has been found that superplastic materials usually have a very fine grain structure (less than 10 pm).8 and it has been proposedg that such a structure alone is sufficient for superplasticity. The purpose of the present study was to further characterize the high-temperature tensile properties of W-Re alloys to determine the conditions under which they might be superplastic. Tensile and selected strain-rate sensitivity tests were conducted on alloys containing 0 to 33.3 at. pct Re at temperatures from 78" to 3630°F. Grain-growth rates were also determined on most alloys at 3630°F. Fig. 1 indicates the compositions evaluated and their locations relative to the solvus line in the tungsten-rich end of the W-Re phase diagram. Twelve binary W-Re alloys containing up to 33.3 at pct Re were double electron-beam-melted and subsequently fabricated to 0.3-in. rod by extrusion and swaging. The starting materials were commercial powders of tungsten and rhenium with impurity levels as listed in Table I. The various blended W-Re compositions were hydrostatically pressed at 70 ksi. The pressed bars were drip-melted into 1.5-in.-diam ingots and then remelted into 2-in.-diam ingots at a chamber pressure of 10~5 torr. The ingots were canned in molybdenum and extruded to round bar at a reduction ratio of 6:l. The alloy extrusions were swaged to about an 80 pct reduction at 2100" to 2900°F. Buttonhead tensile specimens with a reduced section diameter of 0.16 in. and a gage length of 1.0 in. were centerless-ground from the swaged bars

Jan 1, 1970

By Pol Duwez, Paul Pietrokowsky

Titanium and vanadium form a complete series of solid solutions at temperatures above 885°C. Below 885°C, vanadium is slightly soluble in a titanium (about 1.5 pct V at 650°C) and a two-phase a plus ß region extends to 18.5 pct V at 650°C. The alloys up to 15.0 pct V transform into a supersaturated a solid solution upon rapid cooling from the ß phase. Above 15 pct V the ß phase may be retained. The temperature at which the ß to a' martensite-type transformation takes place decreases steadily from 850°C for 0.5 pct V to 325°C for 12.7 pct V. IN the transition series of the periodic table, the six elements that have a body-centered cubic structure at all temperatures, namely chromium, vanadium, molybdenum, columbium, tungsten, and tantalum, fulfill the conditions required for the existence of complete series of solid solutions with the high temperature (ß) form of titanium. Up to the present time, complete solubility at temperatures above the a to ß transformation of titanium has been observed in the systems Ti-MO,1,2 Ti-Cb,2 Ti-W,³ and Ti-Ta.³ The two remaining elements, vanadium and chromium, have atomic diameters which are not as near that of titanium as the atomic diameters of the four other elements. Both are smaller than titanium and the difference, expressed in percentage of the titanium atomic diameter, is 12.3 pct for chromium and 8.2 pct for vanadium. On this basis, the least favorable conditions for solid-solution formation are therefore encountered in the Ti-Cr system. The early work on the Ti-Cr system4 revealed that up to about 1100°C the solubility of chromium in ß titanium is limited, and an intermetallic phase exists near the stoichiometric composition TiCr2. It was found later' that a continuous series of solid solutions extends across the diagram at higher temperatures, and TiCr2 forms by solid state reaction. It became apparent therefore that complete solubility would also be present in the Ti-V system. The present investigation confirms this possibility. The iodide-refined titanium used in this investigation was purchased from the New Jersey Zinc Co., New York. According to the manufacturer, a typical analysis of this product is 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb. The Vickers hardness number (10 kg load) of the crystalline bar varies between 55 and 80. The vanadium metal was purchased from the Westinghouse Electric Corp., Lamp Div., Bloomfield, N. J. The purity of this metal is probably above 99 pct V. The oxygen content must have been quite low, since a bar about 1/4 in. square could be cold rolled into a ribbon 0.020 in. thick. To prepare the various alloys on the titanium-rich side of the diagram, the titanium rod was machined into cups 1 cm in diam and about 1.5 cm high. Pieces of vanadium, of the proper weight, were cut from the square bars and placed within the cups prior to melting. On the vanadium-rich end of the diagram, single pieces of the metals, in the proper weight pro-

Jan 1, 1953

DEVELOPMENT of a chemical process for the extraction of pure metals from mill concentrates or metal scrap has progressed beyond the pilot plant stage and may prove an important adjunct to present smelting and refining methods if initial commercial operations prove economically successful. Developed by the Chemical Construction Corp., the new process involves the treatment of oxide and sulphide ore concentrates by chemical methods, instead of the usual smelting and refining techniques. Several of the many applications are now scheduled for commercial use. Refiners using the new process will prepare ore concentrates by standard flotation methods, introduce the concentrate as a slurry into an autoclave along with water and an acid or ammonia. From the resulting leach solution, recovery of individual metals is made by use of suitable reducing agents. By varying conditions during treatment, different metals in the ore are produced separately as pure powders, which may be pressed into forms ready to market, or in the case of copper, extruded as rods or pipe. The reagents are generally recovered. By manipulating the variables during reduction, selective separation of nickel, and/or cobalt, and/or copper can be made simultaneously. The separation is a continuous operation. Low metal prices are not immediately in view because of the tremendous demand at this time. However, reduced metallurgical treatment costs will allow economical mining of orebodies with lower metal content, permitting increased production to meet demand. Although the practical horizon for use of the new process appears to be limitless, one factor may enter into its employment. Just how low grade a concentrate can be economically used is unknown. In addition, for present practical considerations, only metal below zinc in the electromotive series may be processed. Each commercial application requires specific technique adaptation and pilot-plant data for engineering design. A nickel-cobalt-copper process has been researched and piloted in collaboration with Sherritt Gordon Mines, Ltd., for the firm's Lynn Lake properties. In addition, processes were tailored for cobalt concentrates of Howe Sound Mining Co., and National Lead Co., in view of the urgent need for this specific metal. Major General William N. Porter, president of Chemical Construction, says of the new process, "piloting experience has shown that production cost, from ore concentrates to pure metals should be considerably below current costs." Other savings may be realized by cutting transportation and personnel costs, and by reducing the time lag between mining and pure metal from months to a matter of hours. First commercial use of the process will start sometime this summer. Chemico is slated to finish building a $2.5 million cobalt refinery for Howe Sound Mining near Salt Lake City. The plant is expected to raise world cobalt production by 40 pct. The plant will process 35 tons of 20 pct cobalt concentrates from Howe Sound's Blackbird mine near Cobalt, Idaho, daily. Yearly production is expected to reach 2000 tons of pure metal, about one half of U. S. consumption in 1950. Steps in the Howe Sound application of the process are: 1. Acid oxidation leach. 2. Filtration (residues thrown away are insoluble compounds-gangue, iron, arsenic). 3. Cementation (for Cu removal because Cu content is too low for recovery). 4. Reduction from ammoniacal solution. 5. Separation of Co and Ni as mixed metals (95 pct Co and 5 pct Ni). 6. Recovery of ammonium sulphate. Under construction at the Fredericktown, Mo., mine of National Lead is a $5 million refinery sched- [ ]

Jan 1, 1952

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By E. H. Rennhack, J. F. Libsch

Definite transition behavior was found in unalloyed titanium at 0.13 pct 0 equivalent. The addition of 0.5 Sn, 1.0 Al, 0.5 Al, and 1.0 Sn lowers the tvansition temperature of titanium at oxygen equivalents exceeding 0.22, 0.29, 0.40, and 0.51, respectively. Metallographic evidence indicates that progressive amounts of oxygen restrict deformation at low temperatures resulting eventually in brittle fracture. The presence of tin or aluminum is thought to alter the atomic distribution of oxygen within the titanium lattice in such a manner as to facilitate some degree of slip and twinning. 1 ITANIUM-like iron and zinc experiences a transition from ductile to brittle fracture with decreasing temperature. The presence of sufficient quantities of the interstitial elements, carbon, oxygen, and nitrogen in solid solution, has been shown to progressively lower the room-temperature impact resistance of titanium with increasing interstitial content.1"1 Ogden,et al,2 reported finding no transition from ductile to brittle fracture with decreasing temperature in iodide titanium. However, a definite transition was found to occur at 0.36 pct 0 equivalent in an alloy containing 0.47 pct carbon in solid solution. The oxygen equivalent in this case was obtained by assuming the effects of carbon, oxygen, and nitrogen in combination on the impact properties of titanium to be additive on the same basis as their separate effects on tensile strength, namely: Oe = 2/3 (pct C) + pet 0 + 2 (pet N) They concluded that the tendency toward transition behavior is dependent on the total interstitial content in solid solution and not on any one particular interstitial element. Rennhack,4 however, recently found transition behavior in iodide titanium at an oxygen equivalent of 0.17 pct. Ogden, etal3, reported that the strengthening effects of carbon, oxygen, and nitrogen in titanium decrease with the addition of tin. They showed that tin additions increase the tolerance of titanium for the interstitials, that is, 10 pct Sn permitted individual additions of up to 0.4 wt pct of the interstitial elements without any significant loss in ductility. Aluminum tends to decrease ductility and impact strength of titanium for a given interstitial ~ontent.3 Van Thyne and Kessler5 found that the solid solubility of carbon in titanium doubled in the presence of 10 pct Al. The precise effects of tin and aluminum in the nrespncp of rorvfen nn the impact properties of titanium had previously not been determined. The high oxygen tolerance of titanium containing tin may provide a suitable means for improving the impact properties of titanium containing the interstitial elements, particularly oxygen. Unlike tin, however, aluminum has a high affinity for oxygen and will reduce rutile titanium dioxide (TiO2)by a thermit-type reaction.6 Thus, the atomic distribution of oxygen in titanium might be different in the presence of aluminum. The present work was undertaken to: 1) Determine the effect of oxygen on the transition behavior of unalloyed iodide titanium. 2) Determine the effect of small amounts of tin and aluminum on the transition behavior of iodide titanium in the presence of oxygen and other interstitial~. EXPERIMENTAL Three different lots of iodide titanium were employed to prepare the alloys studied in the present work. Their chemical composition is presented in Table I. The compositions of the tin and aluminum used for alloying are shown in Table 11. Oxygen additions were made using calcined rutile titanium dioxide (TiO2)of 99.7 pct purity. Alloy Preparation—Four titanium-base alloys containing separate additions of 0.5 and 1.0 pct each

Jan 1, 1960

By J. W. Spretnak, H. R. Ogden, A. G. Imgram

The effect of working reduction, stress-relief annealing, and recrystallized grain size on the tensile and notch-tensile properties of molybdenum and Mo-0.5 Ti was studied. It was found that increasing the amount of working reduction increased the strength and reduced the tendencies toward brittle behavior. Stress -relief annealing did not alter the strength but lowered the transition temperature. Increasing the recrystallized grain size lowered the strength and raised the transition temperature. The notch -unnotch strength ratio began to decrease with decreasing temperature at temperatures below those at which the notched ductility fell to zero for all of the micro structural conditions investigated. BEING bcc metals, the refractory metals in Groups Va and VIa (V, Cb, Ta, and Cr, Mo, W) undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures. Previous research has shown that molybdenum and tungsten not only have higher transition temperatures than columbium and tantalum but show a marked sensitivity of transition temperature to structure as well.' Recrystallized materials become brittle at considerably higher temperatures than is the case with material having a worked or fibered micro-structure. Evidence of structure sensitivity has also been detected in columbium- and tantalum-base alloys containing appreciable amounts of molybdenum or tungsten such as F-48 (Cb-15W-5Mo-1Zr) and Ta-10w.2 This paper describes the results of research conducted to further evaluate the effects of metal. lurgical structure on the low-temperature tensile and notch-tensile properties of molybdenum and Mo-0.5Ti. The effects of rolling reduction, stress-relief annealing temperature, and recrystallized grain size were studied. Considerable progress has been made in explaining the fundamental mechanisms of the flow and fracture characteristics of bcc metals. Several of these concepts are helpful in interpreting the data obtained in this study. Brittle fractures occur when the highly temperature-sensitive yield strength equals, or exceeds, the temperature-insensitive brittle cleavage fracture stress.3 The rapid increase in yield strength with decreasing temperature, characteristic of all bcc metals, is therefore of primary concern. petch4 has described the yield strength, ay, (stress required to initiate plastic flow) of bcc metals by the expression where ai is the frictional resistance to slip, Ky is a constant numerically equal to the slope of a a vs curve, and 2d is the average grain diamefer. The oi term itself is thought to be composed of a temperature-insensitive component dependent on impurity content and second-phase particles and a temperature-sensitive component dependent on the Pierls-Nabarro force.5 This equation has also been demonstrated to hold for the flow stress (stress required to maintain continued plastic flow).' Brittle-crack nucleation is thought to occur by the coalescence of dislocations piled up in slip planes at sessile dislocations or twin and grain boundaries.7,8 These proposed mechanisms require that a large number of dislocations be released into the active slip planes so that sufficiently large stress concentrations are produced at the dislocation pile-ups to enable coalescence into a micro-crack. Therefore, at least a microscopic amount of slip must occur in some grains to facilitate initial crack formation. Cottrell 7 has predicted that brittle fracture, nucleated by slip, should occur when where ty is the shear yield strength, ß = 1 in un- notched xension, u is the shear modulus, and y is the effective surface energy. This equation incorporates the Griffith concept of fracture that a crack will propagate if the decrease in strain energy equals or exceeds the increase in surface energy.

Jan 1, 1964

By Waldemar Lindgren

IN spite of a world production of lead amounting to 1,300,000 tons, of which the United States produces slightly less than one-half, it appears that the mines at present are hardly able to supply the demand. For this there are several reasons. The lead deposits, geologically speaking, were formed comparatively near the surface under conditions of lower temperatures, with the richer deposits often residuary; that is, enriched by surface water, and consequently soon exhausted. Lead is practically absent from a great part of the world. The great Canadian shield, the eastern part of the Dominion, contains practically none. Scandinavia contains no lead. It is absent from geo- logical formations of great age, but does occur in large quantities in the deposits in the Rocky Mountain region. These deposits are, more or less directly, of igneous origin, but here, too, there is a tendency of the lead shoots to concentrate in the upper part, and when they go down the deposits turn to zinc-copper and some other metals. This is one of the best established facts of economic geology. The deposits of the Mississippi Valley district, from Kansas-Oklahoma, to Canada, are in comparatively accessible limestone beds, at a depth seldom more than 500 ft. Therefore, the lead is easily mined but more easily exhausted.

Jan 1, 1926

By AIME AIME

THE value to the engineering profession of a liaison between the engineering societies of Russia and America, through Engineering Council, was the subject of a meeting in the Engineering Societies Building attended by over 500 persons. In introducing the subject, Mr. N. A. Stephanoff, President of the Russian Society of America, said: In Russia, engineers were divided into two classes: those who had graduated from the high technical schools and the practical engineers who had graduated from special technical schools. These technical schools were divided into three groups: The first corresponded to the German polytechnical schools with many departments, mechanical, chemical, metallurgical, mining, etc. The second group corresponded to the French special schools of the "Écoles des Ponts et Chaussées." "École des Mines." The third group was formed by the Military and Naval Academies of Engineers. In 1910, Russia's high technical schools had about 45,000 students, whose training covered a period of not less than five years, and who enjoyed all opportunities afforded by laboratories in no way inferior to those of Germany.

Jan 1, 1920

By Hans Lundberq

IINDUSTRY'S attention is now focused on the production of munitions thereby creating a demand for certain minerals which in prewar days were produced only in limited quantities. Now production of these minerals must he increased from the known deposits and new deposits must be found. Can geophysics help? "War minerals" such as tin, vanadium, tungsten, antimony, manganese, chromium, and cinnabar have no physical characteristics sufficiently different front the country rook to permit their direct location by ordinary geophysical methods. As already demonstrated in work on gold and oil, useful information may be obtained indirectly, however, outlining structural features or geological conditions favorable for the deposition of such ores or the accumulation of oil. Recently, more direct and truly qualitative methods have been brought into a useful and practical stage, and by the combined application of old and new methods a technique has been developed which, it is hoped, will be of importance in the search for these vital minerals.

Jan 1, 1941

By Augustus Locke

MY conclusions apply to the engineer in California ore hunting; and, because the product has been overwhelmingly gold, that means gold-ore hunting. But, I wish to think of ore hunting, not as employment for engineers, but as engineering. I wish, moreover, to think of it as productive of ore in significant quantity. The small mine, even if good, means little. Only new districts, or large extensions of old districts can engage our attention here. The conclusions are summarized as follows: (1) The bright color of California mining history comes from the suddenness and intensity of its outburst of gold. Had the mining been averaged from the start, it would soon have become dimmed among greater industries. For fifty years, California has proceeded as an agricultural, timber and oil, but not a mining region. 1

Jan 1, 1931

Readers of recent Bulletins have doubtless observed that the problem of improving both material and moral condition of employees is receiving close attention from influential members of the Institute. This will lend interest to certain developments and investigations that have been reported elsewhere.

Jan 5, 1918