Search Documents

By G. F. Comstock

These notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."l In that paper and the resulting discussion, several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8-in. (9.5-mm.) steel plate, about 21/4 by 13/4 in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extended through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what Mr. Miller called cem-entite and Mr. Jeffries martensite, while Mr. Ruder and Professor Boyls-ton think that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Pig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1920

By C. A. Hartnagel, D. H. Newland

The market for Pennsylvania grade showed a drop both in demand and in prices, which reacted unfavorably on New York oil production, all of which comes under that classification. The output for the year in New York amounted to 5,045,200 bbl. The production in 1937 was 5,478,000 bbl., the largest in any year for the last half century or more. Falling prices, of course, affected new drilling. They declined from $2.20 a barrel, which was posted at the start, to $1.68 in the final months of 1938. With this came a reduction in the amount of oil that would be accepted by the refineries operating in the New York fields. Conditions therefore have combined to halt, at least temporarily, the growth of oil production in the state, which had experienced a steady gain for the last 15 years or more, the yield having risen from less than 1,000,000 bbl. to the round total of 5,500,000 bbl. in 1937. Practically all the oil now obtained is from old, developed fields. No new pools have been found in the last quarter of a century or more. The larger share comes from flooding the sands. Although there are many wells that still produce without the aid of the water drive, they are small and for the most part are pumped periodically. Of late, new drilling has been restricted mainly to that required to maintain existing flood projects. Because of the high initial cost and time required to put a flood into production, the depressed condition of the market has been a serious handicap financially, and, further, has been an unfavorable influence on the planning of operations to secure the maximum recovery of the oil. Unless market conditions improve, it is certain that the effects will be shown in the yield for some time to come. Gas Developments Drilling was active in the southwestern area, chiefly in Allegany and Steuben Counties, and some notable wells were brought in that tapped the Oriskany sandstone. Altogether 42 holes were put down in the two counties, of which 31 were listed as producers and 11 were dry. The new wells gave an initial daily flow of 239,000 M cu. ft. At the close of

Jan 1, 1939

By C. A. Hartnagel, D. H. Newland

The market for Pennsylvania grade showed a drop both in demand and in prices, which reacted unfavorably on New York oil production, all of which comes under that classification. The output for the year in New York amounted to 5,045,200 bbl. The production in 1937 was 5,478,000 bbl., the largest in any year for the last half century or more. Falling prices, of course, affected new drilling. They declined from $2.20 a barrel, which was posted at the start, to $1.68 in the final months of 1938. With this came a reduction in the amount of oil that would be accepted by the refineries operating in the New York fields. Conditions therefore have combined to halt, at least temporarily, the growth of oil production in the state, which had experienced a steady gain for the last 15 years or more, the yield having risen from less than 1,000,000 bbl. to the round total of 5,500,000 bbl. in 1937. Practically all the oil now obtained is from old, developed fields. No new pools have been found in the last quarter of a century or more. The larger share comes from flooding the sands. Although there are many wells that still produce without the aid of the water drive, they are small and for the most part are pumped periodically. Of late, new drilling has been restricted mainly to that required to maintain existing flood projects. Because of the high initial cost and time required to put a flood into production, the depressed condition of the market has been a serious handicap financially, and, further, has been an unfavorable influence on the planning of operations to secure the maximum recovery of the oil. Unless market conditions improve, it is certain that the effects will be shown in the yield for some time to come. Gas Developments Drilling was active in the southwestern area, chiefly in Allegany and Steuben Counties, and some notable wells were brought in that tapped the Oriskany sandstone. Altogether 42 holes were put down in the two counties, of which 31 were listed as producers and 11 were dry. The new wells gave an initial daily flow of 239,000 M cu. ft. At the close of

Jan 1, 1939

By W. H. Eardley

It is increasingly evident that the excellence of blast-furnace operation to a great extent depends upon the preparation of the products fed into the furnace. The preparation of these products is carried on largely in the roasting and sintering departments. Prior to the building of flotation plants in Utah and other western states for the treatment of lead-zinc ores, the gravity concentrates received at the Midvale smelter amounted to about 4000 tons per month, containing 24 per cent. lead and 10 or 11 per cent. zinc. This product was about 20 mesh—that is, 45 per cent. of it would be plus 20 mesh and the balance minus 20 mesh. About 1000 tons of pyrite per month, containing 5 per cent. lead and 10 per cent. zinc, was also received. These products were sent to the multiple-hearth roasters for calcining, after which they were sent to the Dwight-Lloyd machines for sintering with other ores. The sintering charge passed over the machines but once. The first flotation products received consisted of a wet, sticky, muddy mass, containing a large amount of moisture, up to 19 or 20 per cent., and it was almost impossible to feed them with any degree of regularity, if at all, through our standard feeders; but the amount of flotation product received during the first year or so was relatively small and it virtually lost its identity by being mixed with a large amount of jig and table concentrates. As the quantity of flotation products increased, more efficient filtering was accomplished and the moisture greatly reduced. Flotation Products Received At the present time the Midvale plant receives about 4300 tons per month of flotation product running 60 per cent, lead and 4.5 per cent. zinc, 85 per cent. of which is minus 200 mesh and contains about 8 per cent, moisture; and 4000 tons per month of pyrite of similar fineness, running about 2 per cent. lead and 3.5 per cent. zinc, containing about 10 per cent, moisture. The lower moisture greatly reduces the difficulties of handling, making it possible to run a 100 per cent. flotation feed on a multiple-hearth furnace without serious mechanical troubles. The calcine, however, would contain nodules and balls of unroast,ed concentrates, sulfur elimination

Jan 1, 1928

By W. H. Eardley

IT IS increasingly evident that the excellence of blast-furnace operation to a great extent depends upon the preparation of the products fed into the furnace. The preparation of these products is carried on largely in the roasting and sintering departments. Prior to the building of flotation plants in Utah and other western states for the treatment of lead-zinc ores, the gravity concentrates received at the Midvale smelter amounted to about 4000 tons per month, containing 24 per cent. lead and 10 or 11 per cent. zinc. This product was about 20 mesh-that is, 45 per cent. of it would be plus 20 mesh and the balance minus 20 mesh. About 1000 tons of pyrite per month, containing 5 per cent. lead and 10 per cent. zinc, was also received. These products were sent to the multiple-hearth roasters for calcining, after which they were sent to the Dwight-Lloyd machines for sintering with other ores. The sintering charge passed over the machines but once. The first flotation products received consisted of a wet, sticky, muddy mass, containing a large amount of moisture, up to 19 or 20 per cent., and it was almost impossible to feed .them with any degree of regularity, if at all, through our standard feeders; but the amount of flotation product received during the first year or so was relatively small and it virtually lost its identity by being mixed with a large amount of jig and table concentrates. As the quantity of flotation products increased, more efficient filtering was accomplished and the moisture greatly reduced. FLOTATION PRODUCTS RECEIVED At the present time the Midvale plant receives about 4300 tons per month of flotation product running 60 per cent. lead and 4.5 per cent. zinc, 85 per cent. of which is minus 200 mesh and contains about 8 per cent. moisture; and 4000 tons per month of pyrite of similar fineness, running about 2 per cent. lead and 3.5 per cent. zinc, containing about 10 per cent. moisture. The lower moisture greatly reduces the difficulties of handling, making it possible to run a 100 per cent. flotation feed on a multiple-hearth furnace without serious mechanical troubles. The calcine, however, would contain-nodules and balls of unroasted concentrates, sulfur elimination

Jan 1, 1928

By G. C. Broadhead

THE lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top 1. Sandstone (the second of Missouri geologists), - 20 feet. 2. Cbert beds-beds of passage below, - 125 feet 3. Magnesian limestone, chert, and quartzite, - 100 to 300 feet 4. Lower magnesian limestone, - 100 to 150 feet 5. Gritstone and lingula beds, - 50 feet 6. Ozark marble beds, - 5 to 20 feet 7. Sandstone and conglomerate, - 5 to 90 feet 8. Porphyry, Archaean. 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as de¬tached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have pene¬trated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous sandrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called u mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

Jan 1, 1877

By G. C. Broadhead

The lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top: 1. Sandstone (the second of Missouri geologists),.... 20 feet. 2. Chert beds—beds of passage below,...... 126 " 3. Magnesian limestone, chert, and quartzite,. .. 100 to 300 " 4. Lower magnesian limestone,......100 to 150 " 5. Gritstone and lingula beds,....... 50 " 6. Ozark marble beds,........5 to 20 " 7. Sandstone and conglomerate,. .. .. 5 to 90 " 8. Porphyry, Archæan 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as detached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have penetrated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous saudrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called " mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

By E. P. Hindes

The total amount of oil produced in the state of Oklahoma during the year 1928 was 242,286,400 bbl., as compared to 273,372,650 bbl. in 1927; 177,650,000 bbl. in 1926; and 167,900,000 bbl. in 1925. The year 1928 ranks second to 1927 in which more oil was produced in the state than in any previous year. The large in in 1927 and 1928 was due principally to the development of the Greater Seminole district. The decrease of approximately 31,000,000 bbl. in the 1928 production as compared with the production in 1927, was caused by a drop of nearly 8,500,000 bbl. in the Seminole district production and a more or less normal decline in the production of practically all the other older and more settled fields. During 1928 approximately 1800 producing wells were drilled in Oklahoma, which yielded during the year approximately 90,000,000 bbl. of oil. The average initial production of these wells was 850 bbl. per day, and the average daily production per well for the year was 137 bbl. The average daily production per well of the total number of wells producing in 1928 was 10.9 bbl., which is a 13.5 per cent. decrease from the 1927 average of 12.6 barrels. At the close of 1928 a total of 95,400 producing wells had been drilled in the state, and approximately 61,000 were still producing. The grand total amount of oil produced in the state from the time the first well was drilled up to and including 1928 was 2,553,000,000 bbl. The production in 1928 was 9.5 per cent. of the total oil produced in the state. Texas led all other states in 1928, with a production of 251,835,200 bbl. Oklahoma was second with 242,286,400 bbl., and California was third with 231,982,600 barrels. Fields outside Greater. Seminole District Practically all the old settled fields in Oklahoma experienced a normal and expected decline during the year 1928. The fields showing the most, pronounced decline as compared to 1927 were: Burbank, which dropped from 15,230,400 to 11,939, 150 bbl.; Tonkawa, from 7,692,000 to 4,952,900 bbl.; Garber, from 5,056,300 to 3,139,400 bbl., and Wewoka, from 6,188,-800 to 2,450,400 bbl. There were no new extensions, discoveries of

Jan 1, 1929

AN intermetallic compound, Ni3A1, has an ordered fcc structure of type Ll2, and shows peculiar dependence of the yield stress upon temperature; i.e., the yield stress increases by a factor of six upon raising the temperature from 77" to 900K1, 2 This compound is technologically important, since many nickel-base superalloys owe their high-temperature strength to the peculiar yield stress behavior of Ni3Al. The only study of the elastic behavior of this compound was made by Davies and Stoloff,1 who determined Young's modulus of poly crystalline Ni3A1 between 300" and 730°K. The determination of single-crystal elastic constants of Ni3A1 is therefore of interest in connection with dislocation dynamics and is reported in this paper. A single-crystal specimen, 1 by 1 by 3 cm, was cut from an ingot generously supplied by Dr. B. H. Kear of Pratt & Whitney Aircraft. Following initial machining with a Servomet and a surface grinder, the specimen was etched and annealed at 1100°C for 5 hr in vacuum followed by furnace cooling. Two parallel faces were oriented normal to within ±l deg of a [I101 crystallographic axis by the back-reflection Laue technique. The parallel faces were hand-lapped, etched, and polished by the usual metallographic procedures. Final thickness along the [I101 axis was (0.9325 * 0.0005) cm. Chemical analysis gave an average composition of 87.35 pct Ni. Total impurity content is esimated to be no more than 0.1 pct. The elastic constants were calculated from measurements of ultrasonic waves which were propagated along the [110] axis. A longitudinal wave and two shear waves whose displacements are aligned along the [ 110], [li~], and [001] directions, respectively, are necessary in order to completely specify the three elastic constants. Two 3/6-in. quartz transducers were bonded to the parallel faces of the sample with ~ac-seal.3 Although this bond was sensitive to thermal shock, it performed satisfactorily over the entire temperature range for both longitudinal and shear wave propagation. A frequency of 5 mHz was employed in the method of Williams and Lamb4 in order to measure the absolute value of the ultrasonic velocity. The pulse-overlap technique of Mcskimin5 was also used at this frequency in order to determine the shift in the ultrasonic velocity

Jan 1, 1970

By Bain, Edgar C.

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin. Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead-antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By J. F. Ednie

SCRAP metals to the value of more than a billion and a half dollars were recovered in the United States in 1939 for further use in industry. Few people have any true conception of the magnitude of the secondary-metal industry as related to that engaged in the production of the primary, or virgin, metals; of its importance, particularly when a shortage of primary metals exists, as at present; or of the advance that has been made in standardizing and improving the quality of its products. Of the iron and steel produced in the United States in 1939 (the data used in this article are largely taken from Bureau of Mines reports for that year) just over 50 per cent came from scrap and slightly less than 50 per cent from ore. Of the principal nonferrous metals-aluminum, anti-mony, copper, lead, nickel, tin, and zinc-63 per cent came from domestic ores and 37 per cent from scrap. Fig. 1 presents graphically the relative tonnage and value of primary and secondary production of ferrous and nonferrous metals. In this chart only purchased secondary metals are considered, the figures being exclusive of "home" or "plant" scrap which amounts to rather large figures in the iron and steel industry. Incidentally, the chart shows that from the tonnage standpoint the iron and steel industry is some twenty times larger than the nonferrous industry, though with regard to the value of the product the ratio drops to about two to one.

Jan 1, 1941

By S. J. Leach

The possible solution of some of the problems raised in H. L. Hartman's article "Determining Ventilation Requirements for Continuous Miners," which appeared in the March 1962 issue of MINING ENGINEERING, is offered by recent investigative work done at the Safety in Mines Research Establishment, Ministry of Power, Sheffield, England. Highlights of this research are outlined here. Accumulations and layers of methane form in a mine roadway because it is difficult to mix methane with air beneath it by turbulent diffusion. Such mixing involves work contrary to buoyancy forces. In specifying requirements for good ventilation it is not, therefore, sufficient to state that the airflow must be turbulent in the absence of methane. Fundamental work at SMRE on the behavior of methane roof layers has led to the formulation of rules for controlling methane roof layers which specify the ventilation velocity needed to ensure adequate mixing in terms of the rate of flow of methane into the layer (V = cu ft per min) and the airway width (D = ft). A "layering number" for methane and air has been defined by [U37/V/D] where U is the mean ventilation velocity in ft/min in the upper half of the airway. In a horizontal airway there is no mixing by turbulent diffusion for values of the layering number less than about 2, resulting in extensive roof layers. But with a layering number of 5, the layer is "brought under control"-i.e., a further increase in the layering number will shorten the length of the layer only slightly, and a small decrease in the layering number will cause only a small increase in the length of the layer. In a sloping roadway with uphill ventilation, higher values of the layering number are needed to achieve this "controlled" condition; the values range from about 5 at small slopes to about 8 at a slope of 1: 10. In downhill ventilation it is possible for layers to "back" against the ventilation, i.e., to flow uphill. The critical condition for preventing backing can also be expressed in terms of the layering number. Backing will be prevented if layering numbers are about 3 for small slopes and about 4.5 for large slopes; these values for downhill ventilation also give good control of the layer.

Jan 10, 1962

By R. G. Davies

WeERTMANI has shown that the high temperature steady state creep rate, i, in lead and indium-base alloys obeys an equation of the form where AH is the activation energy, o the applied stress, n the stress exponent, and R and T have their usual meanings. He observed a variation in n from 4.5 for pure metals to 3 for concentrated alloys, which he interpreted as due to Change in creep mechanism from the climb of dislocations in pure metals to a micro-creep mechanism in the alloys. The Cottrell-Jaswon microcreep mechanism of the moving dislocation taking its impurity atmosphere with it was considered to be the most likely process, although short-range order and the segregation of solute atoms to a stacking fault will also give a stress exponent of 3. Steady state creep has been investigated in a Au - 27 at. pct Cu alloy at temperatures above 1/2 TIM where TIM the absolute melting temperature. As the oxidation resistance of this alloy is excellent all tests were carried out in air with a furnace built to give a temperature variation of less than 1°C along the 60 mm gage length. A lever-arm arrangement applied the stress with a load being adjusted between each creep test to maintain a constant stress. As each test produced less than 0.5 pct creep strain, the variation in stress during the test was negligible. The creep strain was measured by a transducer at the end of one of the alloy-steel grips, with the out of balance potential being finally recorded on a variable speed chart recorder. A typical creep curve is shown in Fig. 1. The results, Fig. 2, confirm that n is nearer to 3 than to 4.5; the creep mechanism could be any of those given above. The activation energy, AH, which is independent of stress, is consistent with a diffusion controlled process; the activation energies for the self-diffusion of gold and for the diffusion of gold into Copper are both -45 kcal per ml., There is now considerable evidence, that, when the steady state creep is dependent upon diffusion, irrespective of the actual creep mechanism, the activation energy is independent of the stress. The author would like to acknowledge the financial assistance provided by the International Atomic Energy Agency, Vienna, and the Argentine Atomic Energy Commission.

Jan 1, 1962

By T. KIRKE ROSE

A Discussion of the paper by H. O. Hofman and M. G. Magnuson, read at the Lake Superior meeting, September, 1904. (British Columbia Meeting, July, 1905.) T. KIRKE ROSE, London, Eng. (communication to the Secretary*`) :-The authors have shown that, under certain conditions, the rate of dissolution of gold by chlorine and bromine is re¬duced by the addition of 10 per cent. of silver to the gold, and that the action is almost stopped when the silver amounts to 30 or 40 per cent. of the alloy. Even if full recognition is given to the practical way in which the work was done, how¬ever, it is to be regretted that Prof. Hofman and Mr. Magnuson did not determine the temperature at which the experiments were carried out. From the details given it may be inferred that the temperature was raised by chemical action by about 20° C. when 21 g. of sulphuric acid were added, and that the mixture was then slowly cooled down during the experiment. When bromine or very weak chlorine solutions were used, there could not have been any perceptible heating action. As the action of both chlorine and bromine is aided by heat, it follows that the stronger solutions of chlorine were given an unfair advantage over the weaker solutions and over bromine. If the temperature had been the same in each case, I do not think that the conclusions given oil p. 432 of the Bi-Monthly Bulletin, March, 1905, 1 would have been found to be justified. (This is speaking generally. In barrel-treatment the conditions are similar to those in the experiments.) The superior speed of bromine as compared with chlorine at equivalent strengths is not yet disproved, and the differences noted between strong and weak solutions of chlorine may have been largely a function of the temperature. Moreover, the authors used somewhat coarse particles of gold

Sep 1, 1905

By Carle R. Hayward

ATHOUGH there are signs of improvement in the lead industry, conditions are still far from what we have been accustomed to call normal. There has been little to stim¬ulate research and those responsible for the finances of the companies have been inclined to discourage expenditures except where need was urgent or the prospect for immediate returns bright. In spite of this fact, improvements have been developed here and there which will be available as business conditions become adjusted. No publicity is allowed at present. The rising price of silver has had a tendency to increase the production of lead from argentiferous ores but the greatest interest continues to be in the secondary field. Practically all lead plants situated near large centers of population are treating scrap materials, particularly battery plates, the quantity of which is increasing with the improvement in automobile sales.

Jan 1, 1936

By R. T. DeHoff

A general method for determining the geometric properties of structures composed of particles which are all the same shape and size is presented. The application of the method requires a knowledge of' the qualitative shape of the particles in the structure, ad a maximum of three simple counting measurenzents, which are made on a representative plane section taken through the structure. It is also shown that the number of different kinds of measurements necessary JOY the complete description of the structure can be decreased if some independent information about individual particles is available. The geometric properties that can be determined quantitatiz~ely from counting measurements for susch structures are size, shape, number, surface area, vlolume, ad such extensive properties as volume Mction and surface area per unit volume. THE simplest kinds of measurements that may be made on a metallographic section are counting measurements. There are three such simple counting measurements, which are determined by sampling the microstructure with a point, a line, and an area. The first of these, the point count, is probably the most familiar among metallographers. The second count, the number of intersections a test line makes with particle outline, is somewhat more recent in its origin and application. The third counting measurement, the number of particle sections observed in unit area of the plane of polish, has long been used in the estimation of grain sizes. The real utility of these three counting measurements lies in the fact that they are rigorously and unambiguously related to certain extensive geometric properties of the three-dimensional structure of which the metallographic section is a sample. These relationships will be reviewed briefly below. Of somewhat secondary importance to the fundamental relationships is the observation that, if some simplifying assumptions about the geometry of the three-dimensional structure are introduced, manipulation of the counting measurements gives a more complete description of the structure. Specifically, in addition to the extensive properties which these measurements rigorously estimate, the number of particles, their size, and their shape may be determined. The purpose of the present paper is to explore the consequences of introducing the assumption of constant size and shape. A later paper will deal with the estimation of geometric properties of structures which may be characterized by a two-parameter size distribution. It should be mentioned that the introduction of this simplest of assumptions, while clearly not generally justified in metallurgical structures, is not without precedent. For example, many estimates of the number of particles per unit volume of structure, based upon a single counting measurement, are scattered throughout the literature.13 Virtually all of these developments assume a constant particle shape, e.g., spherical or polyhydral, and constant size. That such an assumption is necessary is evident from the fact that, for more general structures, more than a single parameter is required to describe the three-dimensional structure, so that the determination of a single parameter on a section would be insufficient to specify the structure. Similar developments for the estimation of particle size from a single counting measurement, e.g., routine grain-size determinations, make the same very limiting assumption,435 but have nonetheless proven of practical value. The present paper embodies a generalized approach to the development of relationships among the two-dimensional counting measurements and the three-dimensional geometry of the structure, subject to the assumption of constant particle size and shape. It is the hope of the author that by presenting the relationships and the assumptions involved in dealing with this approximation, in a single, unified treatment, the reader may be impressed with the usefulness of the counting measurements, may be guided in their application to the estimation of details of the geometry in specific structures in which he may be interested, and may be moved to apply the results, with understanding, to new structural problems. Several authors6, 7 have demonstrated independently that it is possible to obtain unbiased estimates

Jan 1, 1964

R. V. Norris, Wilkes-Barre, Pa. (communication to the Secretary*):—Mr. Stow's paper presents a series of arguments, numbered from 1 to 18, concerning the relative merits of four systems of colliery-ventilation, designated by the author as " plain pressure-ventilation," " plain exhaust-ventilation," " obstructed pressure-ventilation," and " obstructed exhaust-ventilation." These arguments are subsequently compared by means of tables, in which an arbitrary numerical value is assigned to each, and which consequently serve no other purpose than that of showing his opinions and predilections, as indicated by his assignment of the said numerical values. In addition to this general summary, Mr. Stow intimates his preference for a fifth method of colliery-ventilation—namely, what he calls " alternating pressure-ventilation," which consists in the running of the fan at "pressure " during working-hours, and as an " exhaust" between shifts—a system which he proposes as, perhaps, new, yet which he thinks deserves recognition " as a standard form." This proposed " standard form " is not to be found in practice ; and I think it would be impracticable in gaseous mines of large extent, for the following reasons: 1. It takes considerable time to reverse the air-current in a large mine; and the reversal would involve a period of complete stoppage of ventilation, long enough to permit serious accumulations of gas. 2. In shaft- and slope-mines, at least, it is hardly practicable to have " every man out of the mine" during the night, and certainly impracticable to avoid keeping mules and horses inside. 3. The doors necessary to divide and direct the air-current are properly hung to open against the air-pressure; and, unless

Jan 1, 1910

By Peter R. Drummond

THE final casting of refined copper has been re-J- stricted for generations by the following sequence of operations: Filling the reverberatory furnace, melting, skimming, blowing or flapping, and poling. The hoped-for 24 hr cycle, producing 300 tons or more, has been taken up largely with the necessary bat time-consuming tasks of cleaning the bath, sulphur elimination, and in turn removal of excess oxygen to produce tough-pitch copper. Incidental to comparatively slow melting under combustion gases, copper oxides react with the furnace lining, and the slag so-formed must be completely recycled. The three-phase arc furnace has eliminated some of the cycle stages, and telescoped the remainder into a continuous operation. Electrical energy, supplied to graphite electrodes enclosed in high grade refractories, rapidly melts copper cathodes and sustains a stream of metal, containing approximately 0.01 pct oxygen, without contamination from fuel. The arc was struck on the first large electric furnace for melting copper in the United States on April 13, 1949. The earliest use of this type of furnace was at Copper Cliff, Ont., in 1936, and an admirable description of their installation has been published? Copper, melted in the Baltimore furnace, is used to cast billets, and the installation differs somewhat from the Canadian, as will be described. The arc furnace is a heavy-duty, three-phase furnace, holding 50 tons, the general outline of which appears on Fig. 1. The steel shell is 15 ft ID with a bottom radius of 14 ft 2 in. The roof, separate and distinct from the body, consists of a 15-ft water-cooled, cast-steel ring of the same outside diameter as the furnace. The center line of the furnace lies 9 ft 6 in. from that of the trunnions, permitting a 5" backward tilt for skimming, and a 40" maximum nose tilt forward for complete draining. Normally, the furnace overflows by displacement, and the use of the forward tilt arrangement is restricted to covering charging delays. The charging slot, 3 ft 8 in. x 5 in., lies on the north center line, the tap hole on the south, and the 30x30 in. skim door 45" to the west of the slot. The original 20-in. graphite electrodes were replaced with 14 in. in December 1949. Three conventional direct current winch drives, governed by electrical controls, position each electrode which has individual mast supports and counterweights. An independent circulation supplies cooling water for the electrode glands, the roof ring, charge slot, and the skim door frame. Arc Furnace Refractories Hearth: Fused-in monolithic bottoms had been used in copper arc furnaces, installed prior to April 1949. These consisted of thin layers of periclase, successively fused in place over preliminary brick courses. Heat was obtained from the arc, using a T-like arrangement of broken electrodes resting directly on the periclase to be fused. The operation, taking weeks to perform, was very expensive. The chemically-bonded magnesite-brick bottom, installed at Baltimore, was the first of its kind and a radical departure from previous practice. It consists of a 1 to 6-in. layer of castable refractory laid on the steel shell, modifying it to a 12 ft 2 in. bottom radius. Two courses of 9x2 % -in. fireclay straights and keys follow. The third course is made of 9-in. magnesite blocks of special shape to form circles of an inverted arch. It was started by a four piece keystone with skew-backs forming the outer course. The fourth course also started on a central keystone, or button, of four 90" segments, 12 in. diam x 13 Vz in. deep, and continued with 13%-in. blocks. Skewbacks at the shell completed the course to produce a horizontal surface for the side walls with a single course of No. 2 arch fireclay against the steel. Dry chrome-magnesite cement was brushed over each course after laying, and a 1-in. expansion space between the brick and the shell was filled with the same mixture. The total bottom thickness, excluding the castable material, was 5 in. of clay plus 22% in. of chemically-bonded magnesite. Tap Hole: A 5-in. OD and 3-in. ID silicon-carbide tube constitutes the tap hole and is set tangential to the upper course of the furnace bottom. Molten metal fills the tube when the furnace is level and filled to capacity. Side Walls: The lining, against the shell, consists of a 9x4Y2x3 in. soldier course of fireclay, using straights and No. 1 arches to turn the circles. A second soldier course of 9x4'/2x2'/2-in. fireclay was laid in a somewhat similar fashion. Three courses of 13Y2x6x3 in. and 9x6~3 in. of final magnesite, laid flat, completed the lining, using Nos. 1 and 2 keys to turn the circles. Cardboard spacers were placed between every two bricks in horizontal courses, and a thin coat of chrome-magnesite cement filled the joints between the firebrick and magnesite. A sprung-arch spanned the skim door with jambs of suitable magnesite shapes. Charge Slot: The slot is 3 ft 8 in. wide x 5 in. high. A silicon-carbide sill of special shapes has a 30" slope to allow cathodes to slide easily into the bath. The original arch was flat, and composed of Nos. 1 and 2 wedge magnesite with a 6-ft radius. It projected 5 in. over the sill, and, being a flat arch, gave an 18 15/16-in. opening between the inner edge and the metal line. The whole assembly was later raised 9 in., and the flat arch replaced with an arch, the lower edge of which maintained the 5-in, width from the outer to inner edges as shown in Fig. 2. A water-cooled, cast-copper jacket protects the steel shell behind the slot.

Jan 1, 1952

By J. N. Anderson

Developments in reverberatory furnace practice at Noranda over the period 1928 to 1953 are described. Features of interest are increasing furnace tonnage from 700 to 2000 tons per furnace day, the use of the suspended basic roof, and improvements in furnace fuel ratio. Points of comparison and contrast between Canadian and American furnace practice are given. OPERATIONS at the Noranda smelter have been described in a series of papers published between 1930 and 1945.1-4 In the present paper the development of reverberatory furnace practice over the 25 year period from the beginning of operations up to the present time will be reviewed and current furnace practice will be described in some detail. Particular attention will be given to those features which are characteristic of Canadian practice: first, the use of the suspended basic roof; second, the deliberate driving of furnaces to give tonnages in the range of 1400 to 2000 tons of solid charge per furnace day; and third, the continuous operation of furnaces at high tonnage for many years without any extended shutdown for repairs or rebuilding. Finally, points of comparison and contrast between reverberatory furnace practice in Canada and the United States will be discussed. The Noranda smelter, which started in December 1927, was built for the reduction of ore from the Horne mine where early development had shown a comparatively small tonnage of rich cop-per-gold ore of a grade and character which would require direct smelting. The smelter was designed for a capacity of 1000 tons of ore a day and originally consisted of eight roasters, two reverberatory furnaces, and two converters, together with necessary auxiliaries. The discovery of a large new body of ore in 1928 made it necessary to increase both the size and the scope of the reduction plant. A mill which was ultimately brought to a capacity of 3000 tons a day was built for concentrating low grade ore and in addition the capacity of the smelting plant had to be greatly expanded, so that for the next fifteen years every effort in the smelter was directed toward achieving maximum tonnage. Because the layout and design of the smelter made it impracticable to add a third furnace, it was necessary to increase the tonnage on the two original furnaces by improvements in furnace design and operation, roasting and converting equipment being added as required to meet the demands of increased furnace capacity. The smelter tonnage, which reached a peak in 1941, was curtailed in 1944 when it became necessary to operate on a one-furnace basis because of a reduction in the output of the Horne mine due to a shortage of labor. Two-furnace operation at a moderate tonnage was resumed in 1949. In the early years the smelter tonnage was made up almost entirely of Noranda ores and concentrates. However, since 1937 an increasing tonnage of ores and concentrates from other mines has been treated in the smelter. In recent years, with decreased production from the Horne mine, copper concentrates from several mines in the district, treated on a custom basis, have formed an important part of the smelter tonnage. A review of developments in reverberatory furnace practice at Noranda falls naturally into the following four periods: 1—1928 to 1935, the early years; 2—1935 to 1944, the period of greatest change and development; 3—1944 to 1949, one-furnace op-

Jan 1, 1955

By B. H. Bergstram, C. L. Sollenberger

When glass spheres are crushed by slow compression loading, the outer lune-shaped fragments resulting from the fracture consistently fly outward at high velocity. About 45 pct of the strain energy fed into the sphere-platen system reappears in the form of the kinetic energy possessed by these fragments. These measurements were obtained from high-speed photographs. This kinetic energy can be utilized for addtional comminution if the fragments are allowed to impact against a suitable structure. Comminution theory has advanced considerably in recent years by the study of this unit operation under laboratory conditions. Some of the parameters have been isolated, but the experimental measurements of the pertinent quantities, such as energy, particle size, etc., are still only made prior to and after the conclusion of a fracture sequence. The catastrophic fracture process itself has not been adequately studied from a comminution point of view. It has recently been suggested by Gilvarry that the fragments which result from the free crushing of a single glass sphere by slow compression contain a considerable amount of kinetic energy after fracture. This kinetic energy, if properly directed, possibly can be partially utilized to cause additional fracture. In this paper a hypothesis will be presented which suggests that this kinetic energy is necessarily present and that its dissipation is the process by which a large part of the thermal energy imparted to the crushed product is generated. Evidence supporting the existence of kinetic energy and its utilization for secondary fracture will also be presented. THEORETICAL A previous paper4 has shown that the load-deformation curve of a system composed of an elastic sphere gripped by a pair of parallel platens, can be predicted by a consideration of the theories of Hertz as summarized by Timoshenko.' The deformation A, of one half of the system is given by which states that the deformation is a function of the mutually applied load, P, the radius of the sphere, R; and the respective physical properties of Poisson's ratio, v, and Young's modulus of elasticity, Y. The shape of experimental load-deformation curves conform to this relationship. The energy input to the sphere-platen system, can be predicted from the integral of the load acting through the appropriate distance, dA. Since dA can be evaluated in terms of P from the derivative of Eq. 1, this integral can be integrated between limits of 0 and P. The test sphere, however, is loaded at not one but at two points of contact, i.e., at both ends of a diameter, and hence the total energy input, E, is twice the energy input at each end, or The energy input to the system calculated from this equation corresponds to the energy computed from the measured area under the load-deformation curve. Timoshenko, considering the impact of two perfectly elastic spheres, has shown that the inter-penetration distance A is given by - m f (D (^ * ^t w as modified for the special case where one sphere is of infinite radius, i.e., its surface is a plane; where M is the mass of the finite sphere of radius R, and V is the velocity of approach at the start of an impact and also equals the final velocity of separation for perfectly elastic bodies. Because A is also a function of the load and the elastic properties, as shown in Eq. 1, the velocity, V, can also be calculated in terms of the elastic properties and maximum load, P, or

Jan 1, 1961