Search Documents

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

By C. Zener

HE present paper has its origin in an attempt A by the author, extending over the last several years, to understand the influence of the magnetic properties of the constituent atoms upon the various properties of metals and alloys. During this study the author has been impressed by the important role which magnetism plays in the many facets of metallurgy. In writing this paper he has attempted to convey to his colleagues some concept as to the role magnetism will play in the future development of metallurgy. In some of the subjects herein discussed, such as the influence of magnetism upon phase boundaries and upon mechanical properties, only general thermodynamical properties associated with ferromagnetism are introduced. For these subjects, it is not anticipated that any serious differences of opinion will be encountered. A discussion of the other subjects requires the adoption of a quite specific model of the magnetic structure of the metal. This model is discussed under "Magnetic Shells and Their Interactions." The simple model adopted in this paper has been criticized' as being mathematically inconsistent. This criticism has been ably silenced by Dr. W. J. Carr' of this laboratory. The simple model adopted in this paper has been criticized as being inconsistent with observations on magnetic structure using neutron diffraction. This apparent discrepancy has been resolved by Bader3 who has shown that the finite velocity of neutrons prevents neutron beams from detecting the anti-ferromagnetic structure of the type predicted by the simple model adopted in this paper. Magnetic Shells and Their Interactions An electronic shell of an atom is specified by two symbols.' The first symbol is a number and denotes the total quantum number of the shell. The second symbol is a letter and denotes the orbital angular momentum of each electron within the shell. The letters s, p, d, f are used to denote an orbital angular momentum of 0, 1, 2, 3, respectively, in units of h/2a, where h is Planck's constant. As we pass from scandium to nickel in the first transition period, we eraduallv fill the 3d shell. This shell is responsible for ferromagnetism and hence may be called the magnetic shell. The component of the orbital angular momentum along some specified direction must be an integral multiple of h/2~. Thus, for a d electron this component can have any one of the values —2, —1, 0, 1, 2 times h/2a. In addition to its orbital angular momentum, each electron has an intrinsic angular momentum, hereafter called spin, due to a rotation about its own axis. This spin can have either of two components + Yz (h/2a) or — Yz (h/2~) along the specified direction. A fundamental principle of atomic structure, known as Pauli's exclusion principle, is that no two electrons in a given shell may have identical components of orbital angular momentum simultaneous with identical components of spin. The 3d shell thus may have at most ten electrons. Since an intrinsic angular momentum of a charged particle is necessarily associated with a magnetic moment, the spin of an electron may be thought of as referring to either this angular momentum or to the associated magnetic moment. The electron configuration of the ground state of the isolated atoms in the first transition row is reproduced in Table I. The superscript represents the number of electrons in each shell. For the purpose of this paper, the most important principle of atomic structure relates to the manner in which electrons are added to a shell as the atomic number is increased. This principle, commonly known as the principle of highest multiplicity or more simply as Hund's rule, states that within a given shell the maximum number of electrons have spins pointing in the same direction as is consistent with Pauli's exclusion principle. An application of this principle to the d shell is illustrated in Fig. 1, where the spin structure is given for shells containing from 1 to 10 electrons. The physical basis of Hund's rule is the exchange energy discussed first by Heisenberg in 1928. This is a coupling between electrons with parallel spins (spins pointing in the same direction), the coupling

Jan 1, 1956

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in the discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in the smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently in the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of the joined pieces (base metal). The filler metal, solder or braze, is always of lower melting point than the base metal. Consequently with these processes there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Join¬ing operations carried out at temperatures above 500° C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used. Soldering Fluxes Even thoroughly cleaned and degreased, metal surfaces still possess tenacious oxide films which inhibit the soldering of the joint. The reactions which form these films increase with increasing temperature. The rate of oxide formation and the tenacity of the film varies with each base metal. Aluminum, magnesium, stainless and high alloy steels, aluminum and silicon bronzes when exposed to air form hard, adherent oxide films. These metals require highly active and corrosive fluxes to remove and prevent the reformation of oxide films during soldering. Metals such as copper and silver, on the contrary, form less tenacious films at a lower rate, so that mild fluxes are sufficient. Soldering fluxes must dissolve or remove oxides and promote rapid wetting and spreading of the solder. The flux removes the oxide film by loosening and floating it off into the main body of the flux. The oxide removal is often aided by the alloying of the solder with the base metal, undermining small areas of the oxide and detaching them (Anon., 1959). The flux coagulates and suspends the oxide particles which have been loosened. The flux forms a protective cover preventing the reformation of the oxides, permitting the spreading of the solder and the formation of a metallic bond between the solder and the base metal. Constituents of Soldering Fluxes: Soldering fluxes are commonly grouped into three categories: highly corrosive, intermediate, and noncorrosive. One normally would choose to use the least corrosive flux which will give satisfactory performance.

Jan 1, 1983

By D. A. Dahlstrom

WITHIN the past decade, certain economic, legal, and technological changes have intensified the necessity for an efficient classifier or deslimer of particles at and below the 200-mesh point. First, mechanization of mining has increased the percentage of clays, silts, refuse, and high-ash material in the run-of-mine coal. Second, many washing plants must rely on smaller percentages of fresh make-up water because of shortages, economic factors, or legal restrictions on waste water disposal. Finally, the crushing of middlings and coarse refuse plus the trends toward the finer sizes in sales has further increased the amount of fines produced per ton of mine-run coal. A joint consequence of these circumstances has been the augmented percentage and build-up of —200-mesh material in the finer coal fractions and tipple circulating water. This results in the following disadvantages to the operator: (1) Higher ash percentages in the fine coal caused in large measure by the greater ash content of the —200-mesh material, (2) more difficult or expensive recovery of the fine coal from plant slurries, (3) lower filtration, drainage, and drying rates caused chiefly by lower permeability and the greater surface exposed per unit mass of the finer particles, (4) greater difficulty of beneficiatiing the fine coal because of lowered equipment efficiency and the partial "coating-out" of the —200-mesh fraction on the coarser coal particles. Obviously some cheap but effective fine-size classifier must be developed to aid in solving the above problems. To eliminate the generally unwanted —200-mesh fraction from coal slurries, several methods are in use. Probably the most popular with coal operators is the settling cone wherein the larger particles settle downward to the apex of an inverted cone while the slimes and fines are carried upward by vertical fluid currents caused by the overflow of the bulk of the water at the outer rim. The main advantage of the unit is the low initial and operating cost since no moving parts are involved. Disadvantages are primarily low capacity per square foot or floor space and the loss of good coal in the overflow above the 100-mesh size due to localized, high-velocity gradients and nonuniform, fluid-flow patterns, especially at high loadings. Also, when high slime concentrations are present, desliming efficiency is severely injured.', ' Other methods employed are the drag and spiral classifiers and the hydroseparator.' These involve mechanical separations achieved by moving parts and naturally result in higher initial costs. As they are all based on the settling velocity of the particles at the mesh of separation under operating conditions, area requirements are again large per gallon of throughput if they are to classify at the 200-mesh point. Usually the selection is made to operate at a higher throughput and thus sacrifice some coarser coal in the slime overflow. Cyclone Possibilities in Desliming To overcome the disadvantages of present deslirning methods, it is necessary to use a device that exhibits a very stable and uniform flow pattern while greatly increasing the settling velocity of

Jan 1, 1952

By M. C. Flemings, T. S. Piwonka

Pore formation is examined analytically in cellu-larly solidified single crystals, in cylindrical castings of pure metals and alloys, and in unidirectionally solidified castings. Effects are considered of fluid flow. dissolved gas, and surface tension. Experimental results show that flow through a partially solid "mushy" aluminum alloy obeys relations similar to those applicable for flow through other types of porous beds. Flow rate is proportional to the square of the fraction liquid (fL) for fL less than 0.3. Results indicate models chosen for mathematical description of pore formation in alloy solidification are valid. ONE of the solidification variables which is influential in determining mechanical properties of castings and of wrought material produced from cast ingots is porosity. This porosity may result from shrinkage, dissolved gases, or a combination of both, and may take the form of either macroscopic pores in localized areas of the casting or microporosity evenly distributed throughout large areas of the casting. In alloys which freeze over a range of temperatures some microporosity is generally found after solidification. There has been much discussion as to whether the micropores are caused primarily by shrinkage, by gas, or by a combination of both.'-3 There has, however, been little experimental or analytical work performed to delineate the relative contributions of shrinkage and gas in causing microporosity or to quantitatively describe the influence of processing variables on microporosity. Porosity other than microporosity (e.g., center line shrinkage) has also received only limited quantitative treatment.495 The aim of this work is to examine analytically the general problem of pore formation in solidification and to perform limited confirmatory experiments. Consideration is first given to shrinkage porosity in pure and nearly pure metals (shrinkage in cellular growth, centerline shrinkage in cylinders). Next, a discussion is given of formation of shrinkage-caused microporosity in unidirectional solidification and in "mushy" solidification. Finally, influences of dissolved gas and surface tension on microporosity are examined. Numerical results are given for aluminum and an aluminum alloy. Typical examples of microporosity are shown in Figs. 1 to 3, for 1) cellularly solidified aluminum, 2) sand-cast aluminum alloy, and 3) low alloy steel. SHRINKAGE POROSITY IN PURE AND NEARLY PURE METALS 1) Cellular Growth. In cellular freezing of an impure liquid, liquid grooves may exist over a considerable length of the growing crystal.6 The cross-sectional area of the grooves decreases with increasing distance from the cell tips; the root of the groove is blunt if the liquid at this point reaches eutectic composition. As a result of volume contraction during solidification, flow occurs down the groove, parallel to the growth direction; hence, there must be a pressure drop from the groove entrance to points within the groove. The geometry of the groove is simplified to that of a circular cylinder of radius r and length L, Fig. 4, L » r, and a simple and useful limiting case is obtained. This is that, in the circular cylinder freezing at constant velocity, the pressure at the root of the groove is lower than that pressure at radius r in grooves of other geometries where r decreases continuously to a lower limit at L. As discussed below, a pore resulting from a given pressure difference

Jan 1, 1967

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for OFHC copper, and for a series of binary solid solutions of high purity copper with zinc, gallium, germanium, arsenic, and silicon, to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity. The apparatus used was of the torsional pendulum type developed by KeI1 modified so that the specimen and vibrating system could be maintained in a high vacuum. The activation energy for grain boundary relaxation in copper is 33,000 cal per mol. This is considerably less than the activation energy for self-diffusion, in disagreement with Ke's theory2 that the two activation energies should be the same. All the alloying elements increase the activation energy for grain boundary relaxation to approximately 44,000 cal per mol, increasing the grain boundary viscosity at a given temperature. The results are discussed in terms of theories of grain boundary slip put forward by MottQ and by Ke.+ Experiments have also been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. EXPERIMENTS described in this paper were designed to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity, using the internal friction method developed by Kel for measuring grain boundary viscosity. It was considered desirable to make the system under investigation as simple as possible by making experiments on a comprehensive series of binary alloys of copper with the elements immediately following it in the periodic table, i.e., zinc, gallium, germanium, and arsenic. These elements are within the range of favorable size factor for solution in copper, and the systems have been extensively investigated by Hume-Rothery and his co-workers." Later, in order to study the effect of the relative size of the solvent and solute atoms, experiments were made on a series of Cu-Si alloys, since the apparent atomic diameter of silicon when in solution in copper—the diameter necessary to assign to the solute atoms to account for the lattice constant of the solid solutiona—is almost the same as that of the solvent atoms. Preliminary experiments were made to measure the variation of internal friction with temperature for pure copper. Ke made some experiments on copper," but found that the curves obtained were not reproducible in consecutive experiments. The copper was maintained in an argon atmosphere during the experiments but, although he took precautions to exclude oxygen, Ke came to the conclusion that the precautions were not entirely satisfactory, and that the lack of reproducibility must be due to absorption of oxygen by the copper. Experiments have therefore been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. Previous Work Ke made extensive experiments on high purity aluminum and was able to show that the grain boundaries behave viscously at high temperatures. He found that the relative rate of movement of the grains could be expressed as Where v is the velocity of slip, A is the constant, u is the shear stress, H is the activation energy, R is the gas constant, and T is the absolute temperature. By assuming that the boundary layer was one atom thick, he obtained a value for the viscosity which, when extrapolated to the melting point, gave good agreement with the viscosity of the liquid metal at the melting point. Ke also made experiments on other high purity and commercial purity metals:, and on some alloys." " He came to the conclusion2 that the activation energy for grain boundary slip was the same as for self or volume diffusion and for steady state creep in single crystals. Rotherham, Smith, and Greenough" have shown recently that the activation energy for grain boundary slip is not the same as for self-diffusion in tin,

Jan 1, 1957

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.' Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962

By Norman Brown, J. V. Rinnovatore

It was found that a shear stress applied during the recovery had no effect on the amount of recovery if the stress was less than the instantaneous yield point irrespective of the direction of the stress. Large ajplied stresses during recovery had a marked effect, which depended on the direction of stressing. Single strain reversals at -72°C not only produced the Bausch-inger effect but also increased the flow stress. The increase inflow stress was attributed to vacancies, which have appreciable mobility at -72 °C. THEORIES I-' of recovery suggest that the internal stress field of the dislocations plays an essential role. Most investigations of recovery use time and temperature as the independent variables; however, here stress has been introduced as a variable in two ways: 1) by varying the internal stress field according to the amount of strain prior to recovery and 2) by applying an external stress during recovery. Tannen- baum and Kauzrnann studied the effect of applying a stress during recovery by measuring the change in creep rate after recovery; they found that stresses as high as 95 pct of the creep stress had no effect on recovery. Earlier, Wood and scrutton6 showed that an applied stress during creep increased the rate of poly-gonization. The experiment by Wood involved poly-crystalline aluminum whereas Tannenbaum and Kauzmann used a single crystal of zinc. In this investigation, zinc single crystals were used and deformed in a manner to prevent polygonization. Thus, the main difference between this investigation and that of Tannenbaum and Kauzmann is the use of the stress-strain curve instead of creep rate as the index of recovery. In addition, the applied stress during recovery varied

Jan 1, 1961

By Robert C. Emmett, Donald A. Dahlstrom

FOR many years gravitational classification has been employed as a basic tool in beneficiation of minerals and coal. While improvements have been made to increase efficiency and fields of application, the basic flow pattern has remained relatively unchanged in most gravitational classifiers. Feed slurry is introduced into a settling pool wherein the coarser solids settle against either an upward or horizontal fluid current, or a combination of both, and are withdrawn in a concentrated underflow stream. The finer solids below the classification point possess too low a settling velocity and thus are primarily swept out through a weir overflow by the bulk of the fluid. Because of its simplicity, efficiency, and low power and maintenance costs, gravitational classification finds a wide acceptance for separations in the range of 20 to 325 mesh. Two factors resulting from the basic flow pattern employed in gravitational classification present difficult problems for certain installations. If classification at 60 to 200 mesh of separation is desired, capacity in terms of gallons of overflow per minute per square foot of settling pool area must be low to allow required solids to settle to the underflow. If a thousand or more gal per min of feed slurry must be handled, either a very large classifier or a number of smaller units must be employed, taking up floor space and head room. Examples of this are the large classifiers, wetting tanks, or settling tanks used in the coal industry for recovery of process water from fine solids. Units as large as 50 or 60 ft in diam and 60 ft high, requiring substantial amounts of steel, are not uncommon. A second factor is the lack of self-regulation in gravitational classification. As overflow rate increases, mesh of separation increases correspond-ingly. This normally heightens difficulties of bene-ficiation. If a fine mesh of separation is required at varying feed rates, the problem is more than doubled in complexity. One of the primary advantages of gravitational classification is low power requirement. Gravity feeds or very low pressure heads are employed. However, fluid energy is still present in the inlet stream and provision must be made to dissipate it properly to obtain uniform upward or horizontal currents. Rather than waste this energy, it would be desirable to utilize it to secure a greater degree of self-regulation and simultaneously increase classification capacity per square foot of area. A free vortex could be realized by a tangential entry of feed, resulting in generation of centrifugal force to complement force of gravity in its action. With greater force it should be possible to gain finer separation at any overflow rate per square foot of settling pool area as compared with conventional gravitational classification. Furthermore, as feed rate increases, centrifugal force will also increase and at least partially offset faster currents sweeping solid particles to the overflow. A more stable classification point should result. The liquid-solid cyclone is the most common application of a free vortex in the beneficiation field.' Many previous papers have emphasized uniformity of flow pattern within the cyclone which is largely responsible for the sharp classification that can be obtained.'-4 If a free vortex can be maintained in a non-pressurized vessel with a free surface it may be possible to realize a third advantage of sharper classification. This open-top cyclone would then achieve a minimum energy loss comparable to that with conventional classifiers, and a mesh of separation coarser than 150 mesh, extending the range of application of the free vortex. This is not presently possible with ordinary cyclones. To test the applicability of the free vortex to gravitational classification, a 30-in. diameter open-top cyclone was constructed at Northwestern University. The cylindrical section was 30 in. high and the conical section included an angle of 60". The feed nozzle was a standard 4-in. pipe entering tan-gentially, with centerline 17 1/2 in. below the top of the cyclone. The conical section was flanged near

Jan 1, 1954

By Harry Gard Knox, F. R. Harris

This paper covers some of the problems presented to the oil industry in the drilling of oil wells in the open waters of the Gulf of Mexico. The hazards, delays and relative costs of offshore drilling are reviewed and various forms of drilling platforms discussed. The requirements of the offshore drilling rig are summarized together with the principal items affecting the cost of construction. Sea waves and their size and characteristics as affecting offshore platforms are reviewed. Drilling platforms are classified as fixed, or fixed and floating. Fixed platforms of the conventional cofferdam and pile-supported type are discussed together with their good points and their limitations. The desirability is pointed out of eliminating as much offshore work as possible where operations are subjected to constant and expensive delay and substituting therefor the prefabrication of structures ashore or in sheltered waters. Marked economy will come with the standardization of offshore rigs aid special means of transporting them to the site. Several types of structure which are partly pile-supported and partly buoyancy-supported are discussed and their possibilities of future usefulness commented upon. General Considerations The predominant attribute of offshore drilling equipment is that it must be equal to the job in hand. We therefore give first thought to the matter of adequacy. In view of the probable depth of drilling, the investment involved and the per diem labor costs, it is assumed heavy modern drilling equipment will be employed. In order to usc such equipment efficiently, the working deck must be ample in size and strength and supported so as to be relatively free from motion and from green seas even in heavy storms. These requirements necessitate a high and rigid land-based support for the drilling rig and machinery with plenty of space for supplies, such as pipe, mud, water and fuel, with reserves for days when transportation from shore is impracticable. In offshore rigs the crew will be housed onboard in comfortable quarters, probably air conditioned and equipped with a galley and refrigerated food storage. An important consideration will be the ability to transfer stores and crew to and from the rig in all but the heaviest weather and the platforms must be protected from the impact of supply vessels when alongside. It will be essential to maintain continuous communication with shore by radio or cable, not forgetting the possibility of a helicopter landing space for the transfer of crew and light stores as well as a means of general communication. Whatever structure is constructed must be secure from storms of hurricane force and a safe place for the operating crew to work. If the well comes in, the drilling rig will presumably be removed and a small but rugged pile-supported platform will remain to carry the Christmas tree with safe working space around it. It will be protected from damage on all sides by buffer piles or dolphins. It is assumed that the flowing oil will be piped to storage tanks in the vicinity of the well. An individual tank for each well or a

Jan 1, 1949

By Michael P. Richardson

INTRODUCTION This paper is intended to be a summation of the state-of-the-art i n draw theory and draw- point spacing. Knowledge of this very important factor in the successful design and operation of a block caving mine is scarce and nonconclusive. It is hoped that the presentation of this paper will stimulate interest and discussion which will lead to a stronger understanding of these a1 1 important factors. Please note that block caving as used here- in refers to block, panel, and mass caving systems in general, not just to the specific system of block caving where discrete blocks of ore are prepared and caved as a unit. DRAW THEORY The knowledge of draw theory as related to the practice of block caving mines is, unfortunately, very limited. In recent years much work in draw theory has been done in respect to sublevel caving systems and an understanding of draw mechanics relating to sublevel caving seems to be emerging. This work is certainly helpful to those of us interested in block caving but the question of "what goes on up above" still hounds us since we are more interested in the region of draw which begins just above the area where sublevel caving interest ends. Herein is presented a brief summary of draw theory with an attempt to look at the factors which can help our understanding of the area of draw influence in block caving mines. Nature of Gravity Flow An understanding of the flow of granular material (rock, sand, grain, or prill as examples) is the first step toward understanding block caving draw. If we take a supported column of granular material and allow gravity flow through an aperture at the bottom of the column, an ellipsoidal shaped zone of disturbance of the in-place material will form and grow with extraction of material through the aperture. The volume of this zone of disturbance or loosening is about 15 times the volume of material extracted at any given time (Kvapil, 1980). Figure 1 shows the development over time of the zone of disturbance. The ellipsoid of disturbance represents a future ellipsoid of extraction which will equate to the volume of materia1 extracted by that future time. Extraction involves the movement of the particles located vertically over the drawhole directly downward while material outside this direct vertical volume moves radially inward and down toward the drawpoint as shown in Figure 2a. Figure 2b shows the result of this motion on originally horizontal strata within the ore column. Increased draw increases the eccentricity of the ellipsoidal volume or, in other words, the ratio of the height over the width of the disturbed area increases as ore is withdrawn from the column (Kvapil , 1980). This becomes important to block caving since eventually a vertical cylinder of draw will be approximated as this ratio increases without bounds. Figure 3 shows this result. The width of this draw cylinder is a critical dimension for the determination of draw point spacing in relationship to block caving mine design. McCormick (1968) for one, felt that within this cylinder of draw, mass flow would take place. This is the

Jan 1, 1981

By A. H. Duane, A. E. Miller

The high-temperature allotropy of some heavy rare-earth metals and their alloying behavior with magnesium in the 0 to 50 at. pct Mg region was studied by thermal, microscopic, and X-ray methods. Examination of a hcc phase retained upon quenching alloys of different magnesium content confirmed the existence of a bcc high-temperature allotrope in pure gadolinium, terbium, dysprosium, holmium, erbium, thulium, and lutetium. The lattice constants of the pure metals were determined from a Vegard's Law extrapolation and .found to be 4.05, 4.02, 3.98, 3.96, 3.94, 3.92, and 3.90 + 0.02 A, respectively. In all of the systems studied, the high-temperature bcc phase decomposed eutec-toidally, when slowly cooled, into a hexagonal rare earth-Mg solid solution and a simple-cubic peritec-tic AB-type compound. In 1956, Spedding et al.' observed high-temperature resistivity anomalies in the light rare-earth metals and made several unsuccessful attempts to retain the high-temperature form of these materials at room temperature by quenching the pure metals from temperatures near their melting points. High-temperature X-ray techniques were used by Spedding et a1.' in 1959, to investigate the high-temperature allotropy of the rare-earth metals. This study showed that lanthanum, cerium, praseodymium, neodymium, ytterbium, and possibly gadolinium are bcc at temperatures near their melting points. Discontinuous changes in resistivity at elevated temperatures were also observed for pure gadolinium, terbium, dysprosium, holmium, and lutetium, thus indicating the possible existence of a high-temperature crystalline transformation in these metals. However, due to experimental difficulties encountered in the high-temperature X-ray analysis of these metals, their allotropic form was not identified. Spedding et a~.~ in 1960 observed that yttrium displayed a continuous solid solubility with lanthanum at elevated temperatures, thus showing the high-temperature structure of yttrium to be the same as that of lanthanum, i.e., bcc. Similarly, the high-temperature alloying behavior of gadolinium with yttrium showed gadolinium to be bcc at elevated temperatures. The bcc nature of the high-temperature form of yttrium was again recognized in 1960 by Eash and carlson4 in their study of the alloying behavior of yttrium with thorium. Gibson and Carlson, in a similar study of the alloying behavior of yttrium with magnesium, found that by quenching Y-Mg alloys from within the 0-solid solution region, Fig. l, they were able to retain the allotropic form of yttrium. It was the present authors' intention to use this method to show the existence of a bcc high-temperature form of the heavy rare-earth metals gadolinium, terbium, dysprosium, holmium, erbium, thulium, and lutetium. Simultaneous with the present work, Beaudry and Daane' have shown the bcc nature of the high-temperature form of scandium. EXPERIMENTAL PROCEDURES Materials. The rare-earth metals used in this study were prepared by the calcium reduction of the fluoride and were further purified by vacuum distillation. The magnesium was obtained from the New England Lime Co. and was also purified by distillation prior to its use in the preparation of the rare earth-Mg alloys. The results of chemical and spec-

Jan 1, 1964

By Robert :H. . Lesemann

I recently gave a talk at a seminar on mine development in the Eighties. I had to present CRU' s long-range market outlook for copper, lead, zinc, nickel, molybdenum and silver. In reviewing the recent history of each metal, and our projections, I tried to find some common pattern of behavior that could prove a guide in projecting future market behavior. When you sweep aside your input-output models and econometric equations, what you seem to be left with is this: "When a market goes through a prolonged period of price weakness, you can usually look forward to a period of considerable improvement. " "When a market goes through a prolonged period of price strength, you can always anticipate a prolonged period of price weakness." Stated another way, "The better things are, the worse they will get."

Jan 1, 1982

By D. T. Goettge, E. L. Robinson

The phase changes occurring in low carbon steel during hot strip mill rolling are shown to be metallurgically significant when related to commonly used temperature control points, particularly finishing and coiling temperatures. In combination, these temperatures are shown to have an important influence on the level and uniformity of hardness, grain size, and carbide characteristics of the finished hot and cold rolled sheets. PRODUCTION of wide flat-rolled products ordinarily requires a number of operations in sequence to prepare the material for shipment to the customer. Most products are tailor-made for specific end uses, with each operation contributing certain properties to the finished material. Since the characteristics imparted to the semifinished product by a given step in processing carry through to the finished product in varying degrees, it is important that the intermediate stages of production of flat-rolled strip be carried out with the same care which characterizes the last or finishing operations. The step of hot strip mill rolling is common to the production of all of the various types of flat-rolled product; therefore, the hot strip rolling is an especially important point at which to recognize and control those variables which have an effect on the surface characteristics and metallurgical properties of the finished product and which influence the ease of conducting subsequent operations. Orders entered at a producing mill usually show an end use or describe an article or part into which the ordered product is to be fabricated. Applying his experience as to the properties necessary in a finished sheet to suit the end use and to perform successfully in the fabrication involved, the metallurgist selects a steel of suitable composition and deoxidation practice, and slabs of appropriate dimensions are produced for rolling on the hot strip mill. At this stage of processing, the metallurgist faces the problem of controlling hot strip mill practice in the light of his diagnosis of the properties necessary to meet the end use, paying due attention to the accompanying problem of producing a strip which can meet processing requirements on subsequent units in the mill. It is the purpose of this paper to describe some of the factors which he must consider in solving these problems and to indicate some of the principles which guide him. Equipment, Physical Requirements of the Strip, and Temperature Measurement The metallurgist must, of course, be familiar with the physical layout of the mill, the temperature-measuring equipment available, and the physical requirements of the hot strip product before he can apply his metallurgical knowledge to the problem; hence, the first section will consist of a brief discussion of these matters. The usual hot strip mill consists of reheating furnaces, five or six roughing stands including a scale-breaker, holding table, and second scalebreaker, six-stand finishing mill, runout table with spray cooling facilities, and coilers. A schematic diagram of a typical layout is shown in Fig. 1. Slab temperatures are primarily a function of heating time and furnace temperatures, while mill speeds, spray practice, drafting practice, available water pressure, temperature of the cooling water, cross sectional dimensions of the strip, coil size, and equipment limitations, either singly or in combination, determine what rolling temperatures are practical on a given hot strip mill unit. Thus, it is possible that a set of temperatures which can be utilized successfully on one mill cannot be used on another. However, adjustments in temperatures and rolling practice can usually be made to develop the desired metallurgical properties. In addition to the metallurgical properties developed through proper temperature control, the hot strip mill must also provide strip with certain physical attributes which may be summarized as follows: Strip Cross Section—The strip contour should conform to a section which will give the best results in the cold reduction operation. This is generally recognized as a strip with 0.001 to 0.003 in. crown or shoulder-to-shoulder convexity depending on width, and freedom from concave, flat, or wedge-shaped cross sections which cause metal buildup in cold reduction. Excessive drop off in thickness at the edges can also be very detrimental in cold reducing to light gages. Gage, Width, and Camber—All of these must be controlled. For example, rundown or increasing thickness from the front to the back of the coil results in nonuniformity in the thickness of hot-rolled sheet product and in added difficulty with gage and welds in cold reduction. Similarly, excessive width variation is the cause of guide trouble and excessive edge scrap at later stages of processing, while excessive camber is the source of a variety of processing troubles. Type of Oxide—Product intended for pickling should have a predominance of the type of oxide most easily removable in sulfuric acid. It is generally recognized that this type is obtained by use of maximum table cooling water and cold coiling

Jan 1, 1957

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By Walter Crafts, D. C. Hilty

The liquidus diagram for the iron field of the Fe-S-O system has been derived experimentally. The solubility of oxygen in molten Fe-S alloys has been measured at several temperatures and found first to decrease slightly and then increase rapidly with increasing sulphur content. IT is well-known that the types, distribution, and amount of inclusions in any given steel are closely allied with the oxygen and sulphur contents of the metal, so that the term "deoxidation" as conventionally applied in steelmaking refers not only to the control of oxygen and oxide inclusions but to collateral modification of sulphide inclusions as well. Inclusions commonly occur in steel as mixtures of oxides and sulphides, sometimes closely associated and sometimes apparently completely divorced. Their effects on the properties of the metal may vary widely depending on their types and distribution as well as on their quantity. The mechanism by which inclusions form, however, and the means for controlling it are exceedingly complex and not well understood. Nevertheless, as described by Benedicts and Lofquist' and by Wentrup' all oxide and sulphide inclusions, excluding mechanically entrained matter, must result from specific modifications of the basic equilibria of the Fe-S-O system. In an investigation of the mechanism of deoxidation and inclusion formation being carried out at the Union Carbide and Carbon Research Laboratories, it became evident that quantitative data for the fundamental Fe-S-O system were essential to a better understanding of the problem. Consequently, the liquidus surface of the portion of the Fe-S-O diagram of interest in steelmaking has been determined, and the solubility of oxygen in liquid iron containing sulphur has been measured. Fe-S-O Diagram The portion of the Fe-S-O diagram of specific interest in steelmaking is the Fe-FeS-FeO corner. Of the contiguous binary diagrams for this partial system, only those for Fe-FeO and Fe-FeS are known with reasonable certainty.3 Several attempts to derive the FeO-FeS diagram have been made, chief among them being the work of Giani as reported by Oberhoffer,4 and, more recently, that of Vogel and Fulling." Although both Giani and Vogel and Fulling published diagrams for the FeO-FeS system, their observations indicated that the oxide component approximated Fe3O4 rather than FeO, so that there is doubt whether the system is truly binary. Benedicts and Lofquist and also Wentrup published qualitative sketches of the ternary diagram based on the assumption that it was of the type described by Marsh for a ternary system in which two of the contiguous binary systems are simple eutectic systems and the third exhibits a solubility gap in the liquid. Apparently, however, the only previous effort to establish the diagram experimentally was that of Vogel and Fülling whose results are reproduced in Fig. 1. Although defining approximately the limits of the miscibility gap and the location of the ternary eutectic, point E in Fig. I, Vogel and Fülling's diagram must be considered only semiquantitative. It was derived from a limited number of observations mainly along two quasi-binary sections, and the directions of the tie-lines and the location of the critical point, K in Fig. 1, were estimated by computation. Experimental Procedure The experimental technique employed for the present investigation involved melting mixtures of ferrous sulphide and ferric oxide in contact with iron. Since it was considered that in this part of the system the vapor pressures of sulphur and SO, are so low that they would not affect the results significantly, the melting was carried out in a current of argon to sweep out products of any initial re-

Jan 1, 1953

By J. J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. ALTHOUGH the production of aluminum is a large-scale industrial process, consuming approximately 3 pet of all of the electric current generated in this country, the mechanism of the Hall Process remains a 70-year-old mystery. It is a remarkable fact that the aluminum industry, which was established largely through research and owes much of its growth to research, still employs as its basic process the one developed by Charles Martin Hall while he was still a young man working in a woodshed. There are, of course, modifications in detail and a tremendous expansion of the size of the units used, but basically the process employs carbon anodes and a carbon-lined iron vessel as a cathode for the electrolysis of alumina dissolved in molten salt. Of the almost infinite variety of salts available, the relatively minor Greenland mineral, cryolite, 3NaF.A1F3, is still the only one which gives good performance in the electrolysis. In the early days, the process was thought of as a simple one. The dissolved alumina dissociated and, during the electrolysis, the aluminum was carried to the cathode where it was discharged and collected in a pool of metal. The oxygen was carried to the carbon anode where it reacted to form primarily carbon dioxide together with some carbon monoxide. About the only virtue that can be claimed for this hypothesis is that of simplicity. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried. The complexity of the literature on this system is demonstrated in Table I, which shows the ions postulated as being present during the process. This system is not easy to investigate. Cryolite melts at about 1000°C, so that all the investigations are at relatively high temperatures. Molten cryolite fumes in air, particularly if excess aluminum fluoride is present. The cryolite changes composition on heating at 1000°C, principally by reaction with moisture in the air, but apparently also by reaction with oxygen. Cryolite reacts with most of the customary materials of construction, and those that are not attacked by cryolite seem inevitably to react with molten aluminum. Graphite is the only common material that is inert to the electrolytic bath. Pure cryolite can be held in platinum. There is hope that some of the newer refractories will stand up in bath, and their development for this purpose would be a major advance in the field. The techniques to be discussed, then, are not the most advanced ones. Rather, they are examples of old standardized methods applied under difficult conditions. The principal methods that shed real light on the mechanism are density, electrical conductivity, freezing-point lowering, transport number, viscosity measurements, and reactivity of bath with carbon dioxide. The first measurement to be discussed is density. This procedure is relatively straightforward. A hollow platinum bob is suspended by fine platinum wire from an analytical balance into the melt being investigated. Density1-4 of the system sodium fluoride-aluminum fluoride is shown in Fig. 1. There is a maximum in the density near the cryolite composition, but actually the maximum is on the NaF-rich side of cryolite, close to the composition NaF - Na3AlF8. Density measurements are also useful in giving a clue to the nature of cryolite-alumina melts.1, 4 On the first addition of alumina, density decreases, Fig. 2, although the density of alumina, either solid or liquid, is higher than that of cryolite. These density results indicate that the systems are not simple. A great deal of effort has been spent in measuring the electrical conductivity of molten cryolite and of cryolite with various additives. Conductivity measurements are quite easy for fused salts that can be measured in a dip cell, but no successful dip cell has been made available yet for cryolite. Recourse is had

Jan 1, 1959

In 1820, the Board of Public Works was considering some improvements to the canal, in order to reduce the cost of transportation, and in its annual report for that year gives a description of the method of loading the coal from the pit to the boat, and also from the boat to the dealer's yard, which is illuminating in showing how coal of this type should not be handled. It follows:- "It will be seen by the estimates, that the improving the present canal, forming a canal of large dimensions, from the head of the present lower canal to Sabbot Island; erecting locks of large capacity, and making a communication with the river, so as to completely accommodate the coal trade, (except it should hereafter be found necessary to make another communication with the river,) will not cost more than 126,000 dollars. But as there is some doubt whether the streams that may be received into the canal between Sabbot Island and the upper arch, will at all times be competent to supply the locks on that portion, we will extend our calculation to a point nearly half a mile above Pleasants' Island; where, by erecting a dam, any desired quantity may be thrown into the canal. This extension of the canal with one lock, and the dam across the river, is estimated at 34,000 dollars, making in the whole a little over 160,000 dollars. There will then remain a surplus of 40,000 dollars after completing the works to the point last mentioned. "In order to discover what effect the improvement of this first section will have on the tolls, it will be necessary to take a view of the present state of the coal trade, and endeavor to ascertain what change will result from the increased facility of transportation. "That part of the business which is carried on by water, is conducted nearly in this way. When the coal is drawn out of the mines, it is thrown in a heap near the mouth of the mine, or shaft; it is then loaded into carts, and carried to the river bank, where, in some instances, it is discharged from the cart at the brow of the bank, and runs down to the beach near the water's edge; then shovelled into wheel-barrows, and wheeled aboard of the boat, and discharged from the barrows by upsetting. In other instances, the carts are driven on to a kind of scaffold, furnished with a wide spout or director at the edge; by which the coal is conveyed immediately into the boats. These boats are the common James river poplar batteaux, and require three men to each. The up-stream navigation being laborious, the boats are built of light materials, and continue fit for service but a short time, (say) from two to three years; their cost, when new, from fifty to one hundred dollars. "When the river is tolerably flush of water, one of these boats will carry about two hundred bushels; but in low water their load is sometimes diminished to one hundred, and even as low as eighty bushels. They pay for passing the canals and locks to the Basin, one dollar per load; so that when full loads are taken, it will amount to half a

Jan 1, 1942