Search Documents

By J. Gross

G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks: "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well under way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progress Report covering their work to date." PROGRESS REPORT J. Gross, Salt Lake City, Utah. -This has not been a simple problem, and when I tell you that we can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that does not appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correct. The first thing that was realized in this problem was that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. We realized that if we tried to measure the results of crushing or grinding by the ordinary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surface, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought was a method whereby we could measure surface on crushed particles or, we will say, on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realized that it would be rather a com-

Jan 1, 1928

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

By AIME AIME

AWRDED jointly by the four AW Founder Engineering Societies the John Fritz Medal is generally regarded as the most signal honor that American engineers can confer on a fellow engineer. The roll of 34 recipients contains the names of Lord Kelvin, George Westinghouse, Alexander Graham Bell, Thomas. A. Edison, George W. Goethals, Guglielmo Marconi, and Michael I. Pupin; and among members of the A.I.M.E. now living, Sir Robert A. Hadfield, Herbert Hoover, and Daniel C. Jackling. On the evening of March 1 7 the name of Paul Dyer Merica was formally added to this list of illustrious engineers when the medal was presented to him at a dinner at the Metropolitan Club in New York. The citation read. For important contributions to the development of alloys for industrial uses. Arrangements for the dinner were made by the following committee representing the four Founder Societies: R. C. Allen, George S. Davison, A. A. Potter, and J. B. Whitehead.

Jan 1, 1938

By AIME AIME

THE 129th meeting of the American Institute of Mining and Metallurgical Engineers convened at New York City, in the Engineering Societies Building, Feb. 18-20, 1924. On February 21 an excursion was made to the Bethlehem Steel Co., at Bethlehem, where about 200 members and guests were splendidly entertained. An illustrated description of the Bethlehem Plant will be published next month. The meeting and excursion were largely attended; the registration at New York totalled 1276 versus 1201 in 1923. William Kelly, long identified with the iron-mining industry of the Lake Superior district, was elected President of the A. I. M. E. for the coming year, at ,the annual business meeting, Feb. 19, succeeding E. P. Mathewson. The following Directors were also elected (the date signifies year of termination of office; the final figure indicates the "District" the Director represents).

Jan 1, 1924

By Joseph B. Umpleby

WHEN the Cushing field flooded the oil market in 1914 and 1915 with a daily output equal to nearly one-third of the world's production, the situation was soon corrected by increased consumption, and the price of crude oil rose from 45 c. per barrel in, February 1915 to $1.10 in December of the same year-the highest price paid in the Mid-Continent field up to that time. The intensive search for oil during the following seven years failed to disclose a single new ,field equal to Cushing, and many observers concluded that the rapidly increasing number of wells contributing to the world's output, each declining roughly 20 per cent. a year, combined with the rapidly increasing con¬sumption of petroleum, made it highly improbable that any field would; be found again sufficiently large to seri¬ously affect the oil market. That seven exceptional fields should then be discovered simultaneously is a remarkable coincidence. Long Beach, Santa Fe Springs, and Powell, each exceeded Cushing in daily output and reached the apex of their production during a year when Burbank, Tonkawa, - Smackover and Huntington Beach each contributed several times the daily output of the average new pool. This unexpected and tremendous flood of flush production could only have the effect of depressing price and greatly adding to stocks throughout the country. It was particularly depressing in the Mid-Continent as the new oil from California proved of attractive refining grade and because of cheap transportation by water easily undersold Oklahoma crude in the eastern markets.

Jan 1, 1924

By AIME AIME

AMONG the European nations Germany is the center of interest economically as well as politically, and of prime importance for Europe as a whole is Germany's capacity to produce mineral products for armament and for export in exchange for the import of the essential supplies to maintain its industries. So far as minerals are concerned, Germany is worse off than any other great power except Italy, and deficiencies are being met by attempts to increase output from local deposits and by greater use of substitutes derived from domestic raw materials to replace imported metals, petroleum products, and other minerals.

Jan 1, 1939

A. M. Strong, Bishop, Cal. (communication to the Secretary*) :—The paper of Mr. Eeyes gives us the most complete account of the geology of the borax-deposits in the Death Valley region that has yet been published, and is a valuable addition to the geological literature of a very interesting though little-known territory. During the past ten years I have been over much of the northern part of the country described by Mr. Eeyes and the region immediately north of it.

Jan 1, 1910

By Augustus Locke

Jan 1, 1923

By Augustus Locke

Jan 1, 1923

By John Fritz

MEMBERS of the American engineering societies who were in London and Paris during the last days of. June and early July were present at many interesting gatherings. The official delegates of the Founder societies were the specially honored guests of the foreign engineering societies, but other American engineers took part in the meetings. The members of the delegation were: Arthur S. Dwight, Charles F. Rand, William Kelly, representing A. I. M. E.; Ambrose Swasey (general chairman of deputation), Ira N. Hollis, Jesse M. Smith, representing A. S. M. E.; F. B. Jewett, A. E. Kennelly, G. O. Squier, representing A. I. E. E.; Charles T. Main, Robert A. Cummings, John R. Freeman, D. C. Henny, representing A. S. C. E.

Jan 1, 1921

By B. C. Riblet

THE president of a large smelting and refining company once telegraphed me that they had acquired extensive mining interests in northern Peru and requested me to inspect their properties as it would be necessary to install a system of aerial tramways between their mines and treatment plant. The concentrator was about 50 mi. from the coast, reached by a fairly good motor road. From the concentrator an aerial tramway would he required, about 6 mi. long, to their first property, a gold and silver mine. The lower terminal of the tramway was at an elevation of 4000 ft. and the mine at an elevation of 9500 ft.

Jan 1, 1937

By REED H. HYDE

IN these days of low metal prices and difficult marketing conditions, any treatment that will improve the grade of a product is of interest, particularly when the operation involves little or no addition to the total cost and may even result in a marketable by-product. Such a' combination of circumstances exists, in some cases, in the zinc industry, where it has been found that certain impurities can be removed from .the ore during the Dwight-Lloyd sintering operation, previous to reduction to metal. Consequently it is not surprising that zinc smelters having these sintering machines are paying particular attention to this phase of the operation. Loss of zinc as fume is very low under the conditions obtaining in sintering zinc ores, but impurities such as cadmium and lead are more readily fumed off and it is on this fact that the purification is based. As a result of preferential volatilization of these impurities a sintered product' is made from which purer zinc metal or oxide can be produced, while the fume may be collected and treated to recover the impurity metals. To be effective the operation must be carefully conducted, but no special equipment other than that of a well designed Dwight. Lloyd plant is needed.

Jan 1, 1931

By M. Gensamer, B. Lustman

A recent paper described, by means of stereographic pole figures, the preferred orientations produced by cold-rolling low-carbon steel of automobile-body grade. It was found that the surface of the sheet exhibited a deformation texture significantly different from the texture possessed by the inside of the sheet. Efforts to produce the surface texture by buffing a sample exhibiting the normal or inside texture, using a copper lap, have not been successful. In view of the data collected by Kurdjumow and Sachs2, it was suggested that the surface texture might be the result of partial recrystallization of the normal or inside texture. The recrystallization texture of cold-rolled mild steel was studied by Goss3, but he did not use the pole-figure method, so that his conclusions were in need of verification. For these reasons the work reported in here was undertaken. It had two objectives: (1) to study the general behavior of cold-rolled mild steel on recrystallization below the critical temperature Al, and (2) to attempt experimentally a demonstaration of the genesis suggested above for the surface texture in cold-rolled steel. The material was that used by Gensamer and Mehl, cold-rolled to 97.5 per cent reduction in thickness. Fig. 1 is an X-ray pinhole photo-gram of this material, taken with the beam transmitted perpendicular to the plane of the sheet, using a molybdenum target at 35 kv. with no filter. It is typical of the inside texture, but in it the deformation texture is better developed than in the samples that showed a well developed difference between the inside and surface samples. Specimens from this sheet, which was 0.005 in. thick, were annealed for 5 min. at various temperatures in a lead bath. After about 0.0005 in. had been etched from both surfaces, X-ray photograms were prepared, using the technique described in the earlier paper1. Figs. 2 to 6 are photograms of the annealed sheet, at 566, 571, 577, 580 and 650" C. (1050' to 1202" F.), in order. Fig. 2 shows that 5 min.

Jan 1, 1937

By Robert Ammon

The milling practice at Mascot, at present, consists of dry crushing to % in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. is made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads.......................... 3.55 Jig concentrates................ 61.30 Jig tails......................... 0.80 Flotation concentrates........... 60.60 Flotation tails................... 0.09 Extraction..................... 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows: PEr Cent. Per Cent. Calcium carbonate.............. 48.11 Zinc sulfide.................... 5.43 Magnesium carbonate........... 35.36 Cadmium sulfide............... Nil Silica.......................... 8.73 Lead sulfide................... Nil Alumina....................... 1.04 Iron oxide...................... 1.33 Total....................... 100.00

Jan 1, 1925

By Charles T. Van Winkle

Until the advent of the porphyry coppers and the introduction of flotation which soon followed, crushing and grinding for many years proceeded along somewhat stereotyped lines, without important alteration in type of machinery. For the finer crushing and grinding, stamps, rolls, and various patterns of Huntington and Chilean mills were in general use. Ball-mills were in use abroad, but owing to their small capacity and the high cost of screens and steel, they never obtained much footing in the United States. Tube-mills were first introduced into the crushing departments of cyanide plants when it was found that for crushing finer than 30-mesh other types of crushing machinery were not efficient. In order to crush with one pass, these mills were made 18 to 22 ft. (5.5 to 6.7 m.) in length. Pebbles were used as a grinding medium and the mills were lined with either silex blocks or fragments of quartz or flint pebbles set in cement. While the cylindrical tube pebble-mill had been used to some extent in small installations of concentration mills, the first instance of its use on a large scale was at the concentrating plant of the Miami Copper Co., where 8-ft. by 22-in. (2.5-m. by 55.9-cm.) Hardinge mills were tried out against Chileans. The results of these experiments led to the gradual replacement of the Chilean by the Hardinge mill. Robert Franke published an article' describing the work done, comparing the two types of mills. At the same time, according to Franke, a test was run using a 6-ft. (1.8-m.) Hardinge ball-mill as a substitute for rolls for intermediate crushing on 1/2-in. material. According to Franke, this mill was soon discarded, since it was found that to obtain the desired product the mill must be limited in capacity. The Miami Copper Co. made no test with other types of ball- or pebble-mills. Following this example, others installed the conical type; and when the Inspiration Consolidated Copper Co. decided to build a concentrator, it adopted the conical mill. As the requirements for mills would be very large, it purchased manufacturing rights in the State of Arizona from the

Jan 1, 1918

By Henry Howe

W. E. RUDER, Schenectady, N. Y.-In 1913 I presented a paper before this society on Grain Growth, and at that time it seemed to me that the only explanation for grain growth was that of critical strain. I do not think I published the photographs at the time, but I made some experiments on the effect of stretching sheets of metal. This allowed for fairly accurate determinations of the amount of cold deformation, At the time I worked-with silicon steel because one could see the change in grain growth with the naked eye. I stretched about 10-samples from 0.5 per cent. to 10 per cent., and, after heating to 1,050° C., I found that the maximum grain growth occurred at about 2 ½ per cent. cold deformation. This I designated "the critical strain" for maximum grain growth. About a year ago I talked with Prof. Jeffries, who explained to me his ideas of grain growth. It occurred to me that it would be a very easy thing to check the strain hypothesis against the strain and temperature hypothesis, if we took a certain number of these strips, strained exactly alike and heated to different temperatures; in that case the maximum grain growth ought to appear at a different percentage of deformation for each temperature. These experiments showed that there was, as Mr. Jeffries shows in his present paper, a decrease in germinative temperature with increased cold deformation. The samples were stretched from ½ to 8 per cent. and heated for 10 hr. in hydrogen. Samples were introduced into a furnace previously heated to temperature. A maximum grain growth was obtained at 5 per cent. deformation, when heated to 750° C.; at 2 ½ per cent. when heated to 800' C.; at 1 1/4 per cent., if heated at 950°C.; and at 5/8 per cent.. when heated at 1,100° C. This shows very clearly that the germinative temperature decreases with the increase in cold deformation. The growth was very much more marked, however, at the high temperature, i.e., the grain grew more rapidly and attained a much larger size than at lower temperature. In considering the photographs (Fig. A) those along the lateral edges should be ignored because.

Jan 4, 1917

By Robert Franke

In view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in. For the ore of this mine, a moderately hard but very fissile schist,

Jan 1, 1914

By R. P. Rothwell

THE milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I have thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value and interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern ; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a wet stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulphides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80-stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is man¬aged in a skilful and economical manner, though the necessity for * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

By J. A. B. Forster

The operations of the Electrolytic Zinc Co. of Australasia Ltd. involve the preliminary roasting of zinc concentrate from Broken Hill, New South wales, at a number of acid-making centers on the Australian mainland. The partially roasted material is shipped to the Tasmanian plant where it was formerly re-roasted prior to leaching,' but this practice was gradually abandoned in favor of the flotation of leach residue for the recovery of a concentrate containing about 22 pct sulphide sulphur and known as secontlary or Risdon concentrate.2 This change, together with increased zinc production, called for new furnaces at Risdon for the roasting of 10-50 tonst of secondary concentrcite and 90 tons of new concentrate per day. The war situation made it imperative that construction be commenced without delay and to save time it was decided to base the design on that of Skinner type furnaces which had been built in South Australia twenty years earlier. This involved some sacrifice of desirable features but did not prevent the incorporation of provisions which had enabled small Herreshoff type furnaces to roast secondary concentrate autogenously. The roasting rate in existing furnaces was 10-12 Ib sulphide sulphur per sq ft of hearth area per day, and eleven hearths, 20 ft in diam, were provided in the two new furnaces in anticipation that they would prove capable of the autogenous roasting of 130-140 tons of concentrate per day from 28-29 pct sulphur down to 4.5-5 pct, with an oxidation rate of 11-11.5 lh S/S per sq ft of hearth area per day. It was soon realized, when the first of the furnaces went into operation, that a much better performance than this might be given, and the purpose of this paper is to show how a treatment rate of 100 tons per furnace day, and oxidation rates approaching 15 lb S/S per sq ft per day have been reached. Furnace Design General specifications for the design were based on the results of experience with several other types of furnace and on the special operating conditions

Jan 1, 1950

By Chester A. Fulton

APATITE, the most abundant crystalline phosphate mineral, is found in igneous rocks and probably is the primary origin of all other phosphates, whether mineral or organic. Its chemical formula may be expressed as Ca5(Cl,F) (PO4) 3. The chlorine may be replaced almost entirely by the fluorine. It is found in large or small hexagonal prisms, usually of a vitreous luster and a green or red color, but also violet, white, or yellow. It is found largely as an accessory mineral in granitoid rocks. Its hardness is 4.5 to 5 and its specific gravity is about 3.2. There are many other phosphate minerals-for instance, amblygonite, autonite, collophane, lazulite, monazite, pyromorphite, torbenite, triphylite, turquoise, vivanite, wavellite-with base elements of calcium, magnesium, iron, aluminum, manganese, lead, cerium, lanthanum, lithium, or several of these in combination and with various amounts of water of crystallization. However, these phosphate minerals have but little value save as specimens for mineral collections, the exception perhaps being turquoise. While large deposits of igneous apatite are mined today for the production of fertilizers and chemicals, more than 90 pct of the world phosphate production is derived from secondary apatites, called phosphorites. These calcium (and magnesium, aluminum, and iron) phosphates have been formed in the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rocks containing apatite, bone deposits of prehistoric animals and marine life, or guano deposits (excreta of birds). These phosphorites are mostly alterations of phosphatic limestones that took place slowly over many years. Whether it is apatite or phosphorite that is being produced, it is known in the trade as "phosphate rock." The sedimentary phosphate deposits are of marine origin. Some, as laid down, were rich in phosphate or have become so by subsequent subaqueous action and have not been further enriched since emergence from the sea. Some were originally phosphatic limestones or marls from which calcium carbonate was dissolved away by waters containing carbon dioxide, in which calcium carbonate is much more soluble than

Jan 1, 1949