Search Documents

By P. A. Beck, Hsun Hu

It has been known for many years that in cold drawn polycrystalline aluminum the recrystallization texture is practically identical with the deformation texture.l,2,3 V. Goeler and Sachs4 stated that in cold rolled polycrystalline aluminum, too, the deformation texture is retained upon recrystallization. This behavior was interpreted by Dehlinger9 as an indication that each recrystallized grain inherits the orientation of the matrix in which it grew. However, Burgers and Basart showed6 that in deformed aluminum single crystals the orientation of the recrystallized grains strongly deviates from that of the matrix. Barrett demonstrated8 that even in deformed polycrystalline aggregates the local orientation within each deformed grain changes on recrystallization. No explanation has as yet been offered of how the aggregate texture can be retained, while the local texture is everywhere changing. According to Burgers and Louwerse6 the orientation change on recrystallization in compressed and rolled aluminum single crystals corresponds to a rotation around [112] axes lying in the active slip planes and perpendicular to active slip directions. This orientation change was rationalized by them on the assumption that the orientation of the recrystallized grains is determined by the orientation of the available nuclei, and that these nuclei are small fragments of the deformed crystal, rotated in the deformation process. Barrett pointed out,? however, that these assumptions were by no means proven, and that the total volume of material necessary for the nuclei is so small, that it must be available in any orien- tation whatever. It is, therefore, unlikely that an "oriented nucleation" theory could satisfactorily explain the orientation changes in recrystallization of a deformed crystal. Furthermore, in contradiction to Burgers and LOU-werse's conclusions, Barrett's results for the orientation change could be best expressed in terms of rotations around. [Ill] axes. Thus agreement is lacking not only in the interpretations but apparently even in the experimental results contributed by the various investigators. The orientation relationships on coarsening* in a highly oriented polycrystalline matrix were first investigated by Burgers and Basart.5 They produced a fine grained highly oriented matrix by the recrystallization of a compressed or rolled single crystal of aluminum, and studied the orientation relationships in three successive generations of crystals: the "deformation texture" in the single crystal, the recrystallization texture, and the coarsening texture. Burgers24 showed that the preferred orientation of each successive generation was almost always widely different from that of the preceding one, but that the coarse grains often approximately reverted to the orientation of their grandparent, the deformed single crystal. This observation, and the idea that the orientation of the coarse grains is determined by that of the available "nuclei," led to the concept that the coarse grains are nucleated by the remnants of the deformation texture.12,15 On the other hand, Bowles and Boas16 found, in a carefully conducted experiment, that in recrystallized fine grained copper of cube texture coarse grains grow in orientations which can be derived from the orientation of the recrystallized matrix by rotation around a [lll].] direction: the coarsening texture here does not appear to be related in any simple manner to the original rolling texture from which the cube texture had been obtained by recrystallization. It may be assumed that in a recrystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as "nuclei" for the coarse grains, provided that the conditions are favorable for their growth. The existence of a coarsening texture may be considered as an indication that grains with certain relative orientations with respect to the preferred orientation of their neighbors can grow much faster than others. This "oriented growth" theory was briefly suggested by van Arkel, as early as 1936,13 and it was mentioned by Burgers." Recently, C. G. Dunn produced direct

Jan 1, 1950

By J. A. Stachura

Continuous mining machinery provides the coal industry with one way to compete for a larger share of the total energy market. Various types of machines are discussed and some of the problems with continuous miners, encountered by operators, are reviewed. Equipment manufacturers are working with mine personnel to provide solutions for problems that arise. While coal production over the past 25 or 30 years has been on a horizontal plane, coal's share of the total energy market has declined. To participate more effectively in this total energy market, it is necessary to produce coal more efficiently. It is the obligation of all management, employes, and mining departments to gear the deep mining industry to the rapid progress and changing of today's modern industry. This can be accomplished in the near future with the selection of the proper type of continuous miner best suited to each operator's individual situation. In most mining operations there is tremendous incentive to undertake the continuous mining program. It can reduce the size of the mine greatly by permitting a minimum of working places; it makes pillar recovery work more efficient from the standpoint of overall cost, amount of coal recovered, and safety. The work force can be reduced materially permitting closer and more efficient supervision. It simplifies maintenance because equipment can be more readily standardized. The trend of the coal market favors the use of continuous mining machines. Although there appears to be a general feeling that continuous mining is still a relatively new program and will be slow in replacing conventional mechanical equipment, the fact is that tremendous strides have been made since the first machines were installed in 1948. This program is advancing at approximately the same rate that mobile loading machines replaced hand loading. From 1948 to 1955 there were approximately 450 continuous mining machines in service. In October 1959, a survey revealed that there were more than 700 continuous mining machines in service. Many operators have expressed a desire to undertake this program, but they feel that they could not do so at this time because of one or more of the following reasons: 1) the thickness of their coal seams, 2) seam characteristics, 3) soft bottoms, 4) bad roof conditions, 5) size consist, 6) insufficient flexibility in machines, 7) difficult ventilation problems, and 8) high maintenance costs. With the realization on coal about the same today as it was in 1948, or slightly less and since coal is still failing to participate to a greater degree in the total energy market, it is not surprising that the coal industry is desperately exploring more economical methods for deep mining. The manufacturers are aware that the coal industry is willing to invest in continuous miners if the equipment is built for maximum flexibility, will produce higher tons per man, and assure long life between overhaul programs. CONTINUOUS MINING MACHINES Before discussing details regarding the selection of a continuous miner, let us have a preview of some of the continuous mining machines which are available to the coal industry today. Jeffrey Manufacturing Co.: The machine shown is the Jeffrey 76 A.M. Colmol. This is their most widely used miner, and has been particularly successful in central Pennsylvania and in high-wall mining in western Kentucky. One of the outstanding features of this auger-type miner is its portability. The entire mining range can be changed from its lowest point to the maximum height without stopping the mining operation. Jeffrey 76 B.M. Colmol: This machine is similar to the 76 A.M. model; however, it is built bigger and stronger for a mining range of 50 1/2 to 72 in. This is the model that is now available (Fig. 2). Jeffrey has added two arms to the top row, omitted the odd arm in the bottom row, thus permitting a 50 pct larger throat opening. This eliminates one

Jan 1, 1961

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Incr ase imports. 3. Develop new sources such as synthetic liquid fuels. All three courses may well be needed, as it is doubtful that any one of the three alternatives alone can satisfactorily solve the problem indicated by the prevailing trend in demand for oil. Curtailment of oil consumption is not a constructive policy, except where oil is being wasted or coal can be readily substituted as in stationary steam plants. Reduced oil supplies for most uses will curb our economic advancement and, in addition to inconveniencing consumers, will have a pronounced adverse effect on American industry. The oil-burner-manufacturing industry already has been dealt a hard blow. Shipments in the first 5 months of 1948 decreased 70 pct from those in the same period in 1947.1 The effect of a similar cut in the automobile industry can be imagined. A severe prolonged shortage of gasoline could seriously disturb our present economic well-being. It might be pointed out also that even the prospect of a shortage or lack of assurance for the future can discourage buyers of equipment, as occurred in the case of oil burners. An increase in our imports of oil seems to be a necessary expedient for the immediate future. Its advantages are that it will require a minimum of manpower and steel in a time of critical shortages and will conserve domestic reserves. Any major dependence upon foreign sources for our oil supplies should be avoided, however. Other nations are increasing their oil consumption more rapidly percentagewise than the United States and eventually will compete with us for the not unlimited world supplies. In peacetime, foreign countries might restrict ship- ments of oil to this country or impose exhorbitant prices. In the event of war, there is serious danger that such sources would be cut off, and American-developed oil fields overseas might even be used against us. Although synthetic fuels cannot relieve any oil shortage that might develop within the next year or two, an immediate start toward a substantial synthetics industry to supplement petroleum not only could help relieve shortages several years hence but also would help establish the much needed "know-how" for large-scale production. By assuring ample future supplies, such a start would permit sound planning by industries dependent upon oil and maintain or restore the confidence of prospective customers for oil-con-suming equipment. If it is agreed that domestic production of crude oil cannot be expected to meet future domestic demands, that oil rationing in general is undesirable. and that too great dependence on foreign oil should be avoided—and the weight of the evidence supports such conclusions—it is inescapable that commercial synthetic fuel production should be developed to supplement domestic petroleum supplies, which, of course, will furnish the bulk of our requirements for yean to come. Sources of Synthetic Oil The three principal sources of synthetic oil are natural gas, oil shale, and coal. A commercial plant using natural gas is under construction, and expansion of this industry is expected.

Jan 1, 1950

By H. Kurushima, S. Tsunoda

An investigation of the hydrometallurgy of Cu-Zn concentrates by The Dowa Mining Co. of Japan is described and a detailed flowsheet of the Kosaka hydro-metallurgical plant is given. Sufficient operating experience has shown that the Dorrco FluoSolids system has proven successful for recovery of both zinc and copper by roasting in a fluidized bed. At present, 2400 metric tons of concentrates per month are being treated and recoveries of 93 pct Cu and 65 pct Zn are being effected. A SURVEY of the Japanese chemical industry in 1949 revealed, among other things, that sulphur-bearing blast furnace gas from the Kosaka smelter of The Dowa Mining Co. Ltd., Kosaka, Japan, was being exhausted to the atmosphere as waste. In addition, it was costing that company an average of ten million yen ($28,000) annually for damages to the surrounding property caused by the sulphur dioxide in the gas. It was recommended by this survey that the gas be utilized for the production of sulphuric acid by the contact process. Mr. Kurushima visited the United States in May 1950 to investigate the engineering, construction, and operation of a contact acid plant. Any acid produced at Kosaka would necessarily have to be 98 pct H,SO, to prevent corrosion in railroad tank cars transporting it to the point of use. However, the production of 98 pct acid requires constant volume and SO, content of the gas. As the converter gas at Kosaka fluctuates in both volume and quality, it was decided to evaluate the smelting process with relation to other methods of recovery. This evaluation revealed a relatively new type of roaster, the Dorrco FluoSolids reactor, which was reported to be capable of roasting the copper sulphide concentrate in an excess of air with the production of an SO1 gas strong enough for acid production and a water-soluble copper sulphate calcine. The copper sulphate then could be leached from the roasted ore and electrolytic copper recovered from the leach solution in much the same manner as practiced by the Chile Exploration CO. for treating naturally occuring copper sulphate ores. Use of a reactor of this type would eliminate the need for a blast furnace and converter and, in addition, would effect savings in labor and fuel. The Kosaka ore is a microscopically fine mixture of copper, zinc, and lead sulphides. The lead and a small amount of the barite present can be separated by flotation, but any separation of copper and zinc proved extremely difficult. In blast furnace operation at Kosaka, zinc had been slagged off until a stockpile of about 12,000,000 tons containing 5 pct Zn had been accumulated. Mr. Kurushima felt that if any of the zinc in the concentrate was sulphat-ized and leached with the copper, it also could be recovered electrolytically. The Dorr Co., sponsors of fluidization technique in the metallurgical field, suggested that sulphate roasting be tested out on a laboratory scale and that, if successful, a commercial Dorrco FluoSolids system be constructed. They indicated that the results from such laboratory tests could be transposed to a commercial scale without pilot planting the roasting operation. It was therefore decided to send samples of flotation concentrate to the West-port Mill, laboratories of The Dorr Co., for testing. The objective of Mr. Kurushima's visit to the United States thus had changed from investigation of sulphuric acid plants to a fundamental examination of the hydrometallurgy of copper and zinc. Testing Program In February 1951, Mr. Tsunoda went to the United States to witness the application of the FluoSolids system to sulphate roasting at The Dorr

Jan 1, 1956

By H. J. Ramey

A general solution is presented for the transient temperature distribution caused by radial movement of a cylindrical heat source through a homogeneous medium of infinite extent. This problem represents a highly simplified model of the movement of a combustion front during the thermal recovery of oil. Numerical solutions are presented for a heat source moving at a constant velocity, and a velocity inversely proportional to the radial location of the heat source. Numerical solutions are presented for both finite and infinite vertical thickness of the heat source, i.e., with and without vertical heat losses. The numerical solutions are used to estimate the fuel concentration needed to maintain a combustion front during the thermal recovery of oil. The sensible heat carried to the combustion front by the injected gas stream is discussed in regard to the fuel concentration. Numerical solutions for a heat source (combustion front) of finite vertical thickness indicate the field conditions that may be necessary to sustain the temperature of a combustion front above the ignition temperature of the fuel over considerable distances from an injection well. The results also have implications in regard to the quantity of heat required during ignition. The results of this computation apply to a highly idealized model of a thermal recovery process. But the results may be used as a guide in engineering consideration of the thermal recovery process. INTRODUCTIO N The thermal recovery of crude oil has received considerable attention since the publication by Kuhn and Kochl of laboratory and field tests of this method of oil recovery. Other publications2,3,4,5,6, since that time have dealt with various features of the thermal recovery of oil and have illustrated the extremely complex nature of this process. Vogel and Krueger7 described an electric analog computer designed to solve a moving heat source problem which was analogous to movement of a combustion front during the thermal recovery of oil. The heat source was maintained at constant temperature and was a cylindrical source of infinite height (no vertical heat loss) moving radially at either constant velocity, or at a velocity inversely proportional to the radial location of the heat source. Jenkins and Ramey2 presented analytical solutions to a similar heat conduction problem and pointed out the possible importance of vertical heat losses. The following presents a general solution to the transient heat conduction problem introduced by Jenkins and Ramey4 as well as numerical solutions for a wide range of conditions possibly similar to those that might exist during field operation of the analogous thermal recovery process. DESCRIPTION OF PROBLEM The problem considered in this paper is determination of transient temperature distribution caused by a cylindrical heat source of infinite or finite vertical height, moving radially through an isotropic medium of infinite extent. It is further assumed that the heat flux generated at the surface of the moving heat source may be a function of time such that the fuel concentration required may be constant, or permitted to vary, and that heat is generated at the surface of the heat source only. In regard to the thermal recovery of oil the assumption that heat is generated at the surface of the front is equivalent to assuming that the thickness of the combustion zone is infinitely small, or that the reaction rate between fuel and oxidant gas is infinite. The last assumption does not appear stringent. See laboratory information published by Martin, et al3 Under these assumptions the temperature distribution throughout an infinite medium caused by a heat source moving radially with an arbitrary velocity may be described by The heat generation function or heat flux at the surface of the source, +(t), is Note that the fuel concentration may be defined as a function of time. Eq. 1 is derived in the Appendix.

By B. H. Caudle, R. L. Slobod, E. R. Brownscombe

An earlier publication has discussed three methods lor obtaining relative permeability data on small core sample-: and the apparatus and technique for the capillary pressure displacement method. This paper describes the apparatus and technique for the solution gas and the dynamic displacement methods and presents a routine procedure for obtaining oil-gas and water-oil relative permeability data. Theoretical and experimental considerations are presented to show that the end effect commonly associated with the dynamic flow mechanism is extremely small where constant rates are employed in the flowing phase. An effect of flow rate on relative permeabilities obtained by the dynamic system is found only when gas is one of the flowing phases and this effect is ascribed to a form of channeling in the capillary system. The apparatus and procedure* used to obtain relative permeability data with three phases flowing are described and some preliminary results of the use of this method are shown. INTRODUCTION In a previous publication from this laboratory there appeared a brief discussion of the concepts behind three basic methods for obtaining relative permeability data.' These three methods were called the capillary pressure displacement method. the solution gas displacement method, and the dy. namic displacement method — the names being suggestive of the type of process used for obtaining the desired saturation prior to making the permeability measurements. In the same publication, the apparatus and technique for the capillary pressure displacement method were described and some typical results obtained by this method were presented. This paper will present: 1. The routine procedure used to obtain complete relative permeabilitv data (In small core samples with two phasec flowing; 2. The experimental techniques for the solution gas and dynamic displacement methods for obtaining relative permeability data; 3. The results of some studies on the mechanism of fluid flow through consolidated porous media; and, 4. The preliminary results on the determination of relative permeability for a system in which three phases are flowing. TECHNIQUE AND APPARATUS FOR THE DETERMINATION OF RELATIVE PERMEABILITY WITH TWO PHASES FLOWING In order to obtain relative permeability data on a small core sample which will describe the various phases of reservoir depletion. it is necessary that the methods used duplicate, as closely as possible, the various mechanisms involved in rescbrvoir depletion. It is important that. in any type of relative permedbility determination. the core be originally at virgin reservoir conditions with respect to the fluids within the pore *paces. (for example. oil used to displace water from core until connate water saturation estahlished). and that the subsequent saturation changes in the core be analagous to tile reservoir depletion mechanism for which the data are to he used. PROCEDURE OF DETERMINING RELATIVE PERMEABILITY DATA WITH TWO PHASES FLOWING A standardized procedure has been set up for obtaining relative permeability data and other information on small core samples. This procedure essentially consists of 11 steps as shown below: 1. Determination of tile capillary pressure curve.'! This information is used to help select samples for relative permeability determinations and to charactrrize. in general. the pore size distribution of the sample. 2. Determination of the specific permeabilities to air, oil. and water. These values are those on which the relative pern~eahility calculations are based. 3. Reduction of the core to connate water by an oil drive using the high speed centrifuge. 1. Determination of the critical gas saturation value and the associated relative permeability to oil by the solution gas drive method. 5. Determination of the relative permeabilities to oil and gab in the region where both phases are flowing by the capillary presqure method. 6. Reduction of the sample to residual oil in the centrifuge by an air drive. and the determination of the relative permeability to gas at this point.

Jan 1, 1951

By J. L. Lytton, T. E. Tietz

The recovery of flour stress of recrylstallized are-cast molyhdenum after 10 pet prestrain at 150°C was studied for recovery temperatures of 725o 801o and 901oC. The yield phenomenon observed after recovery was such that the yield drop diminished and disappeared as recovery proceeded. A fractional flow-stress recovery parameter fr, was developed and it was shown that, independent of recovery ternperatzwe, equal f, values of about 0.16 produced superposition of stress-strain curves except for the initial yield phenomenon. The activation energy for low degrees oj recovery was found to he 32,600 cal per mole, in close agreement with a reported valzie for difjzdsion of carbon in molybdenum. For values of fr greater than about 0.15 where recovery was thought to predominate over strain aging, the activation energy varied from 43,600 to 82,500 cal per mole and increased with increasing recovery and recovery temperature. A 10 pet pre-strain shifted the ductile-brittle transition temperature, as indicated by tensile elongation, from 10°C. to about -22"C. A 100-hr recovery anneal at 801oC was shown to shift the transition temperature to about —5oC, the major shift occurring during the first hour of recovery. ThE recovery of cold-worked metals is accompanied by changes in the arrangement of the dislocations generated during cold work. In recent years, the use of transmission electron microscopy has allowed direct observation of some of the dislocation configurations formed, such as "tangles", networks, cells, subboundaries, and loops. These observations have recently been reviewed by Keh and Weissmann.' Accordingly, some understanding has been gained concerning the nature of the dislocation rearrangements involved. The relationship between recovery and the decrease of mechanical strength, however, has only recently been explored. Previous efforts of the authors were directed toward investigating the decrease of tensile flow stress of aluminum and Al-1 pet Mg during recovery2 and the effects of concurrent elastic and plastic strain on the flow-stress recovery of aluminum.3 In addition, an investigation of the effect of four different solute additions on the tensile flow-stress recovery of aluminum has been made.4 Many important metals, however, have the bee crystal structure, e.g., iron, molybdenum, tungsten, vanadium, columbium, tantalum, and chromium. These metals might be expected to behave differently during recovery from those with other crystal structures for two reasons. First, the previous and present investigations of aluminum and its alloys have shown that tensile flow-stress recovery is strongly affected by foreign atoms in the lattice. In the bee metals, interstitial impurities are usually present and might be expected to have various effects upon both flow behavior and recovery. For example, heterogeneous yielding might occur during prestraining. The diffusion of these interstitials can also relock dislocations during recovery so that a yield point might be obtained upon restraining (strain aging). Second, some of the bee metals (e.g., iron, molybdenum, and tungsten) undergo the familiar structure-sensitive ductility transition and exhibit brittle fracture at suitably low temperatures. It is of considerable interest to determine the effects of recovery on the transition temperature of such metals. The purpose of the present investigation was to extend our knowledge of flow-stress recovery to the bee metals and to study the effects of recovery on the ductile-brittle transition temperature. Unalloyed recrystallized are-cast molybdenum was chosen as a test material, since it exhibits a well-defined ductility transition near room temperature. As in the previous studies, the degree of recovery was measured in terms of the decrease of tensile flow stress. Prestraining and restraining were carried out at 150°C to avoid the possibility of brittle fracture. EXPERIMENTAL PROCEDURE The are-cast molybdenum sheet used in this investigation was obtained from the Climax Molybdenum Co. of Michigan. It was 0.060 in. thick by 10

Jan 1, 1964

By R. L. Slobod, B. H. Caudle, E. R. Brownscombe

An earlier publication has discussed three methods lor obtaining relative permeability data on small core sample-: and the apparatus and technique for the capillary pressure displacement method. This paper describes the apparatus and technique for the solution gas and the dynamic displacement methods and presents a routine procedure for obtaining oil-gas and water-oil relative permeability data. Theoretical and experimental considerations are presented to show that the end effect commonly associated with the dynamic flow mechanism is extremely small where constant rates are employed in the flowing phase. An effect of flow rate on relative permeabilities obtained by the dynamic system is found only when gas is one of the flowing phases and this effect is ascribed to a form of channeling in the capillary system. The apparatus and procedure* used to obtain relative permeability data with three phases flowing are described and some preliminary results of the use of this method are shown. INTRODUCTION In a previous publication from this laboratory there appeared a brief discussion of the concepts behind three basic methods for obtaining relative permeability data.' These three methods were called the capillary pressure displacement method. the solution gas displacement method, and the dy. namic displacement method — the names being suggestive of the type of process used for obtaining the desired saturation prior to making the permeability measurements. In the same publication, the apparatus and technique for the capillary pressure displacement method were described and some typical results obtained by this method were presented. This paper will present: 1. The routine procedure used to obtain complete relative permeabilitv data (In small core samples with two phasec flowing; 2. The experimental techniques for the solution gas and dynamic displacement methods for obtaining relative permeability data; 3. The results of some studies on the mechanism of fluid flow through consolidated porous media; and, 4. The preliminary results on the determination of relative permeability for a system in which three phases are flowing. TECHNIQUE AND APPARATUS FOR THE DETERMINATION OF RELATIVE PERMEABILITY WITH TWO PHASES FLOWING In order to obtain relative permeability data on a small core sample which will describe the various phases of reservoir depletion. it is necessary that the methods used duplicate, as closely as possible, the various mechanisms involved in rescbrvoir depletion. It is important that. in any type of relative permedbility determination. the core be originally at virgin reservoir conditions with respect to the fluids within the pore *paces. (for example. oil used to displace water from core until connate water saturation estahlished). and that the subsequent saturation changes in the core be analagous to tile reservoir depletion mechanism for which the data are to he used. PROCEDURE OF DETERMINING RELATIVE PERMEABILITY DATA WITH TWO PHASES FLOWING A standardized procedure has been set up for obtaining relative permeability data and other information on small core samples. This procedure essentially consists of 11 steps as shown below: 1. Determination of tile capillary pressure curve.'! This information is used to help select samples for relative permeability determinations and to charactrrize. in general. the pore size distribution of the sample. 2. Determination of the specific permeabilities to air, oil. and water. These values are those on which the relative pern~eahility calculations are based. 3. Reduction of the core to connate water by an oil drive using the high speed centrifuge. 1. Determination of the critical gas saturation value and the associated relative permeability to oil by the solution gas drive method. 5. Determination of the relative permeabilities to oil and gab in the region where both phases are flowing by the capillary presqure method. 6. Reduction of the sample to residual oil in the centrifuge by an air drive. and the determination of the relative permeability to gas at this point.

Jan 1, 1951

By R. L. Schmidt, J. D. Verhoeven

The diffusion coefficients and electrotralzsport mobilities of aluminum, gallium, and arsenic have been determined in molten germanium with the capillary reservoir technique. The diffusion coefficients are slightly higher than those determined by the solidification technique of Brirton et a1.1 It was found that aluminium and gallium migrate to the cathode in molten germanium) whereas arsenic migrates to the anode under an electric field. A possible technique for producing p-n junctions by means of electric field freezing is discussed in view of the experimental data. In the past decade or so the literature has abounded with articles concerning the solid-state properties of the semiconducting elements germanium and silicon. It is surprising by comparison how little has been published concerning the liquid-state properties of these materials. In the production of doped germanium or silicon the diffusion coefficient of the dopant in liquid germanium or silicon is an important quantity. Yet, to the best of our knowledge, no one has ever made a direct measurement of the diffusion coefficient of solutes in either molten germanium or silicon. A number of authors'-4 have determined some diffusion coefficients by the indirect technique developed by Burton et al.1 This technique appears to give numbers of the correct order of magnitude but it does depend upon a number of assumptions in the analysis and also requires prior knowledge of the viscosity of the melt. In the present work a more direct measure of the diffusion coefficients of arsenic, gallium: and aluminum in molten germanium has been made. It has been shown independently by two groups of authors5, 6 that, when an electric current is passed through the interface of a solidifying metal containing an impurity, the resulting electrotransport in the liquid boundary layer at the interface offers a mechanism for control over the redistribution of the impurity accompanying the solidification. These authors show that the degree of control is proportional to the mobility, U of the impurity atoms in the liquid boundary layer, where the mobility is defined as the drift velocity relative to the solvent per unit electric field. In principle the results apply to the solidification of a doped semiconductor and offer an interesting technique for control of the doping of a semiconductor. In the present work the mobilities of aluminum, gallium, and arsenic were determined in molten germanium in order to evaluate the potential usefulness of electro-transport as a technique for solute control when applied to the solidification of doped germanium. EXPERIMENTAL PROCEDURE Both the diffusion coefficients and the mobilities were measured using high-purity alumina capillaries and a resistivity technique for analysis. A schematic diagram of the electrotransport apparatus is shown in Fig. 1 and the details of the cell design are shown in Fig. 2. For the mobility experiments electrical contact with the bottom of the capillary was made with graphite, as shown in Fig. 2. In order to prevent electrical contact with the melt the graphite was coated with a thin layer of alumina using a plasma spray torch. The cell assembly, a graphite electrode, and another assembly containing two blank capillaries were fastened to the lavite disk shown in Fig. 1. To make a run the system was evacuated and the doped germanium was outgassed at the operating temperature of 1030°C. The cell and blank capillaries were then submerged beneath the melt and a slightly positive pressure of helium was introduced to fill them. After passing current through the cell for a given time the cell and blank capillaries were raised from the melt and the furnace was shut off. The temperature of the cells dropped below the freezing point of germanium within 1 to 2 min after the furnace was shut off.

Jan 1, 1968

By Charles Stein

The effects of several different prior treatments an the creep behavior of 99.9995 pct aluminum at 260°C and 1000 psi canstant stress are compared with annealed specimens. Quenching from 538oC, irradiation with 2 mev electrons, and tension-compression room temperature fatigue damage were used to change the substructure of the specimens prior to their creep testing. The quenched and the irradiated specimens showed a larger primary and transient stage contribution to the creep curve than those specimens which were only annealed prim to creep testing. The specimen receiving prior fatigue damage at room temperature showed no first stage or transient creep when tested under identical conditions as the above specimens and had an average creep rate seven orders of magnitude lower than that of either the annealed, the quenched or the irradiated creep specimens. In a previous electron transmission microscopy investigationl of the substructure developed during the creep of pure aluminum at 0.57 Tm, it was noted that a large concentration of vacancy loops and dislocation loops were present in and near the subboundaries while the interior of the subgrains contained few of these defects and had a low dislocation density, see Fig. 1. Yim and Grant2 and Hazlett3 have shown that the presence in nickel of a substructure developed by prior cold work effectively reduces the primary and transient contributions to the creep curve. Hultgren,4 McLean,5 Gervais, Norton, and Grant,6 Chang and Grant,7 and others have shown the same effect with the higher stacking fault energy material, aluminum. However, the specific defect responsible for the change in the creep behavior developed by the prior cold work was not established. Specifically, what effectively interfered with dislocation motion in these materials at elevated temperatures? Was it jogs on dislocations produced by their interaction with other dislocations or with vacancy or dipole loops, see Fig. 1, or did the subgrain walls determine the mean free path for glissile dislocations? This would be a realistic possibility only if subgrain boundaries are effective barriers to dislocation motion. The ability of a subgrain boundary to act effectively against glissile dislocations depends on the number and the arrangement of dislocations in the subboundary,8 which in turn is a function of the creep strain.' This paper compares the creep rate of specimens possessing a large vacancy concentration to that of annealed specimens and with specimens having a stable subboundary wall containing Lomer locks produced by prior fatigue damage. EXPERIMENTAL PROCEDURE Vacancy Loops. Aluminum creep specimens, 99.9995 pct pure, were machined from zone refined rod to a 2-in. gage length and a cross-sectional area of 0.025 in. These specimens were annealed at 538oC, 1000°F, for 10 min and quenched into ice water. They were then reheated to the creep test temperature of 260°C, 500°F, and held at this temperature for 18 min to al-low for vacancy condensation and loop formation. The specimens were subsequently creep tested at 1000 psi constant stress at 260°C. The temperature along the gage length was monitored by three Pt-Pt, 13 pct Rh thermocouples, two embedded in the upper and lower shoulders of the specimen and one attached to the mid-point of the gage length- The temperature gradient was held to ± l°C or less throughout the Creep test. Elongations were measured by two LVDT's 'connected in an averaging 'On-figuration, with quartz extension arms placed against the specimen at the extremes of the 2-in. gage length. i K 3J?--' * *H - >^> - ' ^L r 77 . *y J OJL, J Fig. 1—Transmission electron micrograph of pure aluminum strained 8.2 pct at 260°C and 1000 psi constant stress. Note the presence of numerous loops near the light dislocation tangle

Jan 1, 1970

By D. C. Jillson

WORK in recent years1-' has indicated a complexity of the processes of deformation of metal crystals not previously appreciated and not fully accounted for by any hypothesis so far advanced. Furthermore, the nature and mechanism of formation of nuclei of recrystallization have not been determined precisely. The deformation of single crystals of zinc has been studied frequently, but the purity of the zinc and the perfection of the specimens sometimes have been given little consideration. Methods have been developed recently that readily yield zinc single-crystal specimens of high quality.5 In the present work, such specimens were deformed in various ways under various conditions, and deformed specimens were annealed to obtain information regarding recovery, recrystallization, and grain growth. The paper attempts to correlate and evaluate previous data, as well as to present new data, in order to determine areas in which more detailed work might be done most profitably. Tests at temperatures from the freezing point (419.46°C) to room temperature revealed glide only on basal planes in a close-packed direction (100)*, as reported by Mark, Polanyi, and Schmid6 and others. Markings probably similar to those observed by Kolesnikov7 and Boas and Schmid8 were noted in specimens stretched at elevated temperatures, but it seemed clear that these were not caused by prismatic or pyramidal slip (see second paragraph of section on Phenomena Involving Bending of the Basal Plane). Twinning Twinning on the octahedral plane of a face-centered cubic metal has been pictured as a process of simple homogeneous shearing along that plane in a [112] direction. It was recognized by Mathewson and Phillipsv and others""" that the (102) twinning of zinc required a somewhat more complex mechanism and might be considered as a homogeneous shearing of (102) planes in a [211] direction plus slight adjustments of atoms to positions of greater stability or lower energy, or as a single movement of each of the atoms in the same sense into the final positions. Gough and Cox" modified Mathewson's mechanism to obtain a more stable lattice configuration, but it is not clear that they succeeded, and their mechanism requires movement of some of the atoms in a sense opposite to that of the overall twinning movement. They also suggested that twinning may occur as a result of previous basal slip. This conclusion was based on the observation that twinning caused by alternating torsion was clearest and most profuse at positions for maximum basal slip rather than for maximum stress on (102) planes in the close-packed direction (not the twinning direction), and no mechanism was described. It might be wondered whether resolution of stresses on the twinning plane in the twinning direction would have afforded a simpler explanation. If twinning is essentially a simple homogeneous shearing along the twinning plane, it would seem that twins should grow by a smooth, continuous mechanism, and, indeed, that a simple reversal of stresses should reverse the shearing and de-twin the crystal. Cylindrical tablets 1/8 to 1/4 in. thick were cleaved from singlle-crystal specimens and were squeezed, perpendicular to a second-order prism plane, to give a tensile stress perpendicular to a first-order prism plane. A "click" was heard and a thin, needle-like twin appeared on the basal cleavage face. If squeezing was continued smoothly, the twin, viewed at magnifications up to X500, grew smoothly and quietly (fig. 1). X-ray examination verified that the twinning was of the (102) type. Rotating the compression axis 90" to reverse the stress then caused a smooth, continuous shrinkage and ultimate disappearance of the twin (fig. 2). The squeezing also caused a rumpling of the basal

Jan 1, 1951

By C. Cronquist

Since April, 1962, Shell Oil Co. has operated a peripheral line-drive waterflood of the 10.750-ft lower Tuscaloosa (Cretaceous) Denkman sand in the Little Creek field. Located in southwestern Mississippi in the lower Tuscaloosa trend, the field was discovered by Shell in Jan., 1958. Among the largest in the trend, the accumulation is controlled stratigraphically and occurs in an extensive series of alluvial-point bar deposits across a nose that dips gently to the south. The crude oil is 39" API gravity and was highly undersaturated at initial conditions. Early production behavior indicated a depletion drive with slight water influx; primary recovery wm estimated to be 25 million bbl, or 24.5 percent of stock-tank oil originally in place. A.s a result of a favorable mobility ratio and remarkably uniform rock properties, the volumetric sweep eficiency in the waterflood has exceeded 90 percent. Despite the high connate water saturation (56 percent), the displacement efficiency by water injection has been quite efficient, contrary to traditional concepts. Based on observed field flood-out performance, ultimate recovery is calculated to be 46 million bbl. As anticipated, the production rate began declining during 1964 due to a continu ing reducrion in the number of producing wells as flood fronts advanced across the field. Cumulative recovery as of Jan., 1968, was 44.8 million bbl; waterflood operations ~hould be complete by 1970. Introduction Most waterfloods described in reservoir engineering literature involve pattern operations, the most common of which is the five-spot pattern. Only occasiona'lly are linear drives described, even though there probably are increasing numbers being put into operation. Increasing use of linear floods may reflect the accelerating trend towards early application of fluid-injection programs when linear drives are more efficient, as was the case at Little Creek. However. the Little Creek operation is unusual in several respects. It is one of a few successful waterfloods conducted in sands with connate water saturations approaching 60 percent, and it is among the deepest successful water-floods being operated anywhere. Development The Little Creek field was discovered in Jan., 1958, in the lower Tuscaloosa trend in southwestern Mississippi (Fig. 1). The discovery well, Shell-Lemann No. 1, was drilled on a seismic closure about 2 miles southeast of lower Tuscaloosa production at Sweetwater. The well was completed in the Denkman sand at 10,752 ft, and on initial potential it flowed 588 BOPD of 39" API crude on a %+-in. choke; psi was 730 and GOR was 442:l. Development proceeded rapidly on 40-acre spacing, and by the end of 1958 the field was producing approximately 9,100 B/D from 56 wells. Almost all this production came from the northern half of the field. The southern part was discovered in Nov., 1958, at a location almost 2 miles from previously established production. Subsequent drilling established an apparent conneotion about half a mile wide between the twd areas. Development of the field was practically complete by 1961 with the drilling of 155 producers and 35 dry holes. Some early wells were completed open hole but moslt are completed with casing cemented through the productive interval and perforated for production. Geology The lower Tuscaloosa structure in this area is a north-south nose with maximum dips of about 2" on the flanks. There is no discernible faulting at the producing horizon. Productive limits of the field are shown in Fig. 2, which is contoured on a marker just above the main productive zone. A common water level at 10,415 ft subsea was logged at both the northwest and southeast ends of the field. There is a gross oil column of nearly 100 ft (Fig. 2). Since there is less than 40 ft of closure, it is apparent that bhe accumubtion is controlled stratigraphically, being limited by a sand pinch-out across the creslt of the nose. The total produc-

Jan 1, 1969

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By T. J. Whalen, M. Humenik

The liquid surface tension of copper-nickel ad copper-nickel-titanium-carbon alloys and the wettability of titanium caybyde by these alloys have been measuhed. It was found that the surface tensions of the binary copper-nickel alloys Lie on a smooth curve between the end members, copper and nickel. The addition of small amounts of titanium and carbon has nO effect on the surface tensions of copper-nickel alloys. Small additions of nickel to copper significantly reduce the contact angle of Ike alloy with titanium carbide. From a Gibbs treatment, nickel is shown to be adsorbed at the titanium carbide-alloy interface. X HE microstructure of two-phase materials has been shown to be influenced largely by the interfacial energies between the phases present.' , In systems prepared by powder metallurgy techniques and densi-fied in the presence of liquid phase, a precise analysis of microstructure and interfacial energy relationships requires a knowledge of the solid-solid interface energies and liquid-solid interface energies. However, marly metal-nonmetal systems are characterized by the "sweating" of the liquid during sintering, and in these systems wettability is a principal consideration. The wetting in turn is dictated by the various interface energies of the system, as shown in Fig. 1 for a liquid drop formed on a solid substrate. The equation which expresses the vectorial balance of surface forces in the horizontal plane, at the point of contact, A, is given by: where ssv = solid-vapor interface energy sSL = solid-liquid interface energy sLV= liquid-vapor interface energy 6 = contact angle measured through the liquid phase. The angle and the surface tension, slv, can be measured accurately by the sessile drop method.3, The absolute value of the surface energy of the solid cannot be determined by this method, but with reasonable changes in the composition of the liquid only, the value of ssv can be considered constant. The changes in contact angle, then, can be attributed to changes in sSL and sLV and since sLV can be measured, the changes in sSL can be determined. Several studies have indicated that the surface and bulk properties of solid alloys can be correlated with electronic structure. The catalytic activity of copper-nickel alloys was reported to follow the dband vacancies in these alloys.5 Nickel has been considered to have 0.6 holes per atom in the d-band. The addition of copper to nickel is thought to bring about a filling of the d-band of nickel, since each copper atom contributes one electron. Thus, at an atomic concentration of 60 Cu-40 Ni (62 wt pct Cu-38 wt pct Ni) the d-band is believed to be full, and magnetic measurements support this view.6 If the electronic structure is influencing a property of the alloy, this property should show some sort of discontinuity as the composition changes from one side of the 60 Cu-40 Ni composition to the other. Since the catalytic activity can be considered as a surface property of the alloy, it is logical to assume that other surface properties, such as surface tension, may also be influenced by electronic structure. The suggestion has been made that there is a correlation between the solid titanium carbide-liquid Cu-Ni alloy interfacial energy and d-band filling.7 One purpose of this investigation was to determine if the changes taking place in the electronic structure with compositional changes in the solid copper-nickel alloys were reflected in the surface tension values of the liquid alloys. Such a change, if present, would lend support to the suggestion that one can refer to discrete energy bands in the liquid state. Other purposes of the present study were to investigate in detail the wettability in the system copper-nickel-titanium carbide, and to discuss the possible processes which take place during wetting in this system.

Jan 1, 1961

By J. W. Downey, R. A. Morris, M. V. Nevitt

An experimental survey has determined the occurrence of Ti2 Ni-type phases in binary and ternary alloys of Ti, Zr, or Hf with first, second, or third long-period transition metals and also in ternary systems in which 0 is the third component. The existence of eleven previously unreported isomorphs is cited and some approximate phase boundaries are given. Lattice parameters are reported for the new phases. The periodic table relationships involved in the occurrence of the phase are discussed. A previous paper' reported the occurrence of a group of Ti2Ni-type phases (structure-type E93) containing Zr in combination with Rh, Ir, and Pt, and Hf in combination with Rh, Pd, Ir, and Pt, and cited evidence to show that all of the Zr phases and the Hf-Pd phase are not binary phases but occur only when 0 is present. More recently one of the present authors found that in the ternary systems of Ti and 0 with Cr, Mn, Fe, Co, and Ni the occurrence of the Ti2Ni-type phase could be correlated qualitatively with valency electron concentration, and that the role of 0 appeared to be that of an electron acceptor.' This paper describes the results of a broader investigation of the occurrence of Ti2Ni-type phases in binary and ternary systems containing Ti, Zr, or Hf. EXPERIMENTAL PROCEDURE Alloys were prepared by arc melting. The purity of the metals Zr, Rh, Hf, Ir, Pd, and Pt was given in the previous paper.' The additional materials used for this work were metals with a minimum purity of 99.9 pct and reagent grade ZrO2, TiO2, Cr2O3, and NiO. Chemical analysis of several alloys in each system indicated good agreement between intended compositions and cast-button compositions. For the heat treatment precautions were taken to avoid oxygen contamination. The specimens were wrapped in Mo foil and sealed in fused quartz tubes at a room temperature pressure of 1 x mm of Hg. These capsules were then annealed in a vacuum furnace at an external pressure of 5 X mm of Hg. Since the major constituent in most of the alloys studied was the brittle Ti2Ni-type phase, Debye-Scherrer patterns with sharp lines could be obtained with powder crushed from the annealed solid samples without being reannealed. Metallographic, X-ray diffraction, and density determination techniques previously described1, 2 were used. RESULTS AND DISCUSSION Zr-Rh-O, Zr-Ir-Oand Zr-Pt-O Systems-Figs. 1 through 3 show the approximate boundaries of the Ti2Ni-type phase fields at the temperatures indicated in the ternary systems Zr-Rh-O, Zr-Ir-O and Zr-Pt-0. In each isothermal section the Ti2Ni-type phase field is labeled E and the unidentified binary phase found in the previous work' is labeled ?. The dotted lines, which are not phase boundaries, correspond to the composition (Zr2 B)1-xOx. In each system the Ti2Ni-type phase field is displaced to the high-Zr side of this composition line. However, the departures from Zr2B stoichiometry for the metal components are not as high as Zr3B, as was inferred from the previous work. Lattice parameters of the Ti2Ni-type phases in the alloys shown as triangular data points in Figs. 1 through 3 are given in Table IA. The probable compositions of the Ti2Ni-type phases have been estimated from the isothermal sections. Although there are a few exceptions that probably result from uncertainties in phase boundary location and from the effect of variation of oxygen content, the generalization can be

Jan 1, 1961

By Arthur L. Crawford

PLAGER gold is perhaps the most difficult of the common mineral deposits to evaluate. Not only are the erratic pay streaks a source of never-ending uncertainty, but the spotty distribution of the gold in iso¬lated nuggets is a perpetual source of error and disappointment to the sampler. Experienced engineers have long realized this difficulty and have been wary in predicting assay values except in the most general terms, and then only after extensive and usually expensive sampling. During the past year I have had the opportunity of checking a number of gold placers, and from the results obtained I believe that the microscope may be employed to advantage in placer sampling.

Jan 1, 1933

By L. N. Cosner, C. F. Austin, J. K. Pringle

Shock wave attenuation studies with three igneous rocks are reported: a spessartite elastic to low intensity stress waves, a diorite which is anelastic, and a porous scoria. The level of shock passing through a given thickness of rock has been determined by donor-receptor methods using high speed streak cameras. Test results include shock propagation velocities adjacent to the explosive, the dependence of test results upon test geometry, and the variation in shock wave attenuation in these three common igneous rock fabrics. The utilization of explosives in rock mediums involves a series of interrelated phenomena. These are the detonation process within the explosive, the transfer of energy from the explosion products to the surrounding rock medium in the form of sound or shock waves, and the transmission of the resulting waves through the rock medium to create damage in the rock mass. The subject of this paper is the investigation of the close-in phenomena that occur in the intensely shocked rock immediately adjacent to a detonating explosive charge. The specific aspects studied include propagation velocities, free surface velocities, pulse attenuations and the determination of the equations of state for the test rocks employed. In addition, a series of tests was conducted to indicate the dependence of the test results on the charge diameter utilized. The equations of state for rock materials have been investigated by a number of authors. Lombard, ',' Grine and Fowles,3,4 Zharkov, 5 Hughes and McQueen,6 Chabai,7,8 and Bass9 have published equation of state data on rock materials similar in structure or composition to those investigated in the study. Rinehart10 has prepared a voluminous tabulation of the available equation of state data from these publications and in addition has included data on many other rock and earth materials in his compilation. The reader is referred to the extensive tabulations and bibliography of Rinehart for classical studies involving the equations of state of metals and other solids and liquids. The problems of sympathetic detonation between drill holes in hard rock environments has received the attention of various authors as have the problems of explosive rock coupling close-in stress wave attenuation and explosive diameter effects. 11 to 18 In particular, the don or-receptor geometry of this report is very similar to the geometry of adjacent drill holes in rock. Most published pulse velocity and attenuation work in rock has been devoted to velocities at much lower amplitudes than those associated with close-in explosives phenomena and most attenuation studies involve transmission and attenuation across large spans of material. Excellent work in these areas has been published by the U. S. Bureau of Mines and by many individuals and groups engaged in geophysical research. SELECTION OF TEST MATERIALS A series of rock materials was desired for this test program that would be meaningful industrially, and that would also yield comparative results from a research viewpoint. Based on the availability of a series of related petro-fabrics, for which there is an abundance of physical and shock response data, three igneous rocks were selected as the test series. The applicability of shock wave studies in igneous rocks to industrial problems is readily demonstrated. Hardrock tunneling, quarrying and mining take place in igneous rocks throughout the world. From a research point of view, igneous rocks exhibit a wide variety of grain sizes and considerable diversity in composition, yet the common igneous rocks have a general similarity in their constituent mineral structures and in their grain-to-grain bonding mechanisms. The latter is based on the concept of rock formation through magma cooling and crystallization, though the degree of liquefaction in granitic plutonic masses is indeed a moot question. Three specific types of igneous rock were chosen for study. A coarse-grained granitic textured rock was desired that would serve as a representative of the widely abundant intrusive rocks of the world and

Jan 1, 1967

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. [ ] Development of the new units was prompted by a desire for solution of the following problems: 1-The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pet of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be provided in the event that air lines were no longer available. 2-Drill performance has increased beyond the capacity of present 3 ½ -in. drifter machines. 3-The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4-Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5-Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6-In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1-It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1952

By W. O. Philbrook, K. M. Goldman, G. Derge

THIS is the third in a series of papers from the Metals Research Laboratory dealing with the transfer of sulphur across the iron-slag interface in a carbon-saturated system. The first paper' showed that the transfer obeyed first-order kinetics. The second' presented detailed evidence in support of the three-stage mechanism: FeS(Fe) FeS(slag) FeS(slag) + CaO(sing) ? CaS(slag) + FeO(slag) FeO(slag) + C ? Fe + CO. This emphasized the role of an iron-sulphur complex as the transfer agent across the interface and as an essential intermediate in the overall process. The present paper shows the influence on the process of the individual elements, carbon, silicon, manganese, and phosphorus, the alloying elements normally present and of interest in commercial blast furnace operations, aluminum, which has a pronounced accelerating influence, and nickel and copper, which are common minor impurities in the raw materials. The experimental methods and procedures for interpretation of data are the same as described earlier.1,2 Induction heated, graphite crucibles were used, and sulphur-free slag was added to the molten iron containing sulphur and the selected alloy. Slag samples were taken at regular time intervals and analyzed for sulphur and other components of interest. The authors wish to state specifically that these experiments were not intended to simulate industrial blast furnace operations. However, they do represent a study of the kinetics and mechanism of sulphur transfer at the slag-metal interface under specified laboratory control of the major variables in the system. It is believed that the results can be usefully applied to the blast furnace if consideration is given to the differences which are known to exist between the two conditions. A rigorous evaluation of the accuracy of rate studies is difficult. Recognized sources of error include sampling and analysis of both slag and metal, temperature measurement and control, selection of zero time, composition of the gaseous atmosphere over the reaction system, and extraneous sources of sulphur from the graphite crucible and reagent materials. In this study carefully standardized procedures were followed consistently in order to minimize the errors. It is believed that the reproducibil-ity of duplicate runs indicates that errors have been rendered negligible relative to the observed effects from intentional variables. For example, original experimental points for duplicate runs are shown in Figs. 1, 2, 7, etc. In most cases in this paper the drawn curves represent an average of at least two heats. The spread in sulphur values at a given time ranges from 0.02 to 0.08 pct, which is a small frac-tioi of the total values ranging up to 2 pct S in slag. In the systematic study of the influence of alloy additions, each element was added over a range of concentrations. The two slags used in this study were designated as "acid" or 1530 and "basic" or 1545. They had the nominal compositions given in Table I. Rates were measured in the temperature range 1500" to 1650°C. Data will now be presented to illustrate the various features of the study. Silicon The first alloying element examined was silicon, because its presence is unavoidable in any silicate slag system through the reaction y/2SiO2(slag) + xM?y/2Si(liq.Fe) + MxOy where M is any reducing agent such as iron or carbon. It is known that the attainment of equilibrium by this reaction is extremely slow and probably not reached in the blast furnace." The influence of silicon on the final stages of the sulphur reaction has also been studied.' It has been shown5 hat silicon increases the activity of sulphur in iron. For such reasons silicon may also be expected to influence the kinetics of the reaction. The observed effects will now be described. The general procedure was to melt 530 grams of ingot iron in a graphite crucible, 3 in. OD, 2 1/4 in.

Jan 1, 1955

By C. C. Martin, M. C. Fuerstenau, R. B. Bhappu

Experiments revealed that quartz could not be floated in conductivity water at any pH with a long-chained sulfonate as collector. Various cations, Fe+++, Al+++, Pb++, Mn++, Mg++, Ca++, are shown to function as activators when the pH is such that the cation hydrolyzes. As the solubility product of the various cation-sulfonates was exceeded at the concentrations involved, precipitated cation-hydroxy-sulfonates, e.g. Fe (RSO3)2OH must be functioning as the collector in these systems. A number of interesting and important phenomena were revealed during a study of the response of beryl to sulfonate flotation.' Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH 3.0, about three ppm Fe+++ increased recovery of leached beryl from about 60 pct to 100 pct, whereas about four ppm Ca+ + reduced the recovery from 60 pct to 2 pct. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper Sulfonate Flotation of Beryl,' even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation-sulfonates are precipitated immediately in solution. That is, blueish-white clouds were noted to form after given additions of salts to known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe(RCO3)2OH and that bonding to the surface occurs through the hydrogen of the hy-droxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems in the presence of various cations at various values of pH. EXPERIMENTAL MATERIALS AND METHOD Sodium alkyl aryl sulfonate was chosen as the collector for the experimental work. The reagent, sup plied as a courtesy sample by the Shell Chemical Co., has the following physical properties: Physical form Solid — Finely ground Sulfonate content, pct wt 95 to 97 Molecular Weight 450 to 470 Number of carbon atoms in hydrocarbon chain 25 to 30 Melting Point, OF 250 to 260 Solubility Soluble in water with gel formation at concentrations higher than 25 pct by weight sulfonate This particular reagent was chosen because of its high active sulfonate content, long-chain length, and solid form. With the exception of the frother and sulfonate, all other chemicals were of reagent grade quality. Conductivity water was used in the experimental work. This water, made by passing distilled water through an ion exchange column, had an average measured conductivity of one micromho. Experiments were conducted at room temperature in a small glass flotation cell with the following procedure: 1) A redetermined amount of water and salt solution (e.g. CaC12 . 2H2O) were combined and the pH adjusted to a given value. 2) A given amount of sulfonate was added so that final solution volume was 130 cc. 3) One drop of Dow 250 frother was added. 4) Five g of quartz were added and the system conditioned for five minutes. 5) The pH of the system was measured (termed flotation pH).

Jan 1, 1963