Search Documents

By Virgil Miller, F. B. Petermann, S. F. Ravitz

The Cle Elum nickeliferous iron deposit is in Kittitas County, Washington, in a rugged, mountainous region about 23 miles north of the town of Cle Elum. The Biewett Pass deposit, which is similar in character and occurrence, is in Chelan County, about 18 miles east of the Cle Elum deposit. A more or less continuous ore zone may extend between the two deposits, since iron ore is reported to have been discovered at Iron Mountain, which lies directly between them. The ore probably was formed by meta-morphism of laterite resulting from Ieach-ing of serpentine derived from peridotite. It consists largely of magnetite grains distributed through a matrix of limonitic material containing a small amount of hematite and chromite. Many of the chromite grains have shells and inclusions of magnetite. The magnetite grains range in size from 1200-mesh to 1/4-in., the average size being 48 to 65-mesh; the chromite grains range from 20 to 150-mesh. The gangue minerals are olivine and serpentine with a small, amount of chlorite, and appear both as very thin bands in the ore and 's minute fragments in the limonitic matrix. The nickel is present as minUte inclusions of a nickel silicate mineral within the magnetite and gangue par- ticles, varying in size from 1500 to about 280-mesh. Detailed analyses of 3000-lb. lots of Cle Elum and Blewett Pass ore are given in Table I. TABLE i.—Analyses of Ore Samples Per Cent Ore from Constituent cle Elum' Blewett Pass Cr....................... 2.23 2-12 Ni...................... 1.43 0.9s Fe...................... 52.9 41.4 SiOz.................... 5.6 13.4 CaO.................... 0.3 0.8 MgO................... 4-1 7-5 AI2O3................... 7.0 2.g P...................... 0.022 0.034 S....................... O.O1 o.oa Mn..................... I.I 0.4 Ba..................... nil co..................... o.oa 0.02 CU..................... 0.02 0.03 As...................... 0.03 Au..................... nil Ag°..................... O.58 Pt...................... ml Fe++.................... 8.9 5-9 Fe+++.................. 44-0 35-5 « Ounces per ton, 1 sr,cte,so,","&&$ally absent: B, W, M~, T~, V, ~i, Bi, Pb. Sb. Sn. Be, In, Hg. Zn, Zr. Cd. Preliminary Tests Attempts to beneficiate the ore by ore-dressing methods, including various 'cornbinations of sink and float, tabling, jigging, flotation, and magnetic separation, were consistently unsuccessful. A wide variety of roasting and leaching tests were made on both raw and reduced ore, but in most of the tests little or no nickel was extracted, and in none did the extraction exceed 50 Per cent. No nickel could be volatilized as the carbonyl. by treating reduced ore with carbon monoxide. Fairly good sepa-

Jan 1, 1944

By R. E. Ogilvie, N. L. Peterson

DURING the past few years there has been considerable effort devoted to the understanding of radiation effects on materials. The concept of the Frenkel defect and other lattice defects suggests that radiation may alter the rate of many metallurgical phenomena, especially those which are diffusion controlled. In 1953 R. R. Coltman and T. H. ~lewitt' found an appreciable effect on the ordering rate of Cu,Au due to fast neutron bombardment. Since then several rather comprehensive theories have been proposed on radiation enhanced diffusion in solids.2"4 If the energy of the radiation is above the threshold energy for the removal of atoms from their lattice sites, Frenkel defects will be produced. These defects can be produced uniformly throughout a relatively thick specimen by high-energy X-rays permitting bulk property studies without the limitation of sample dimensions. In this work high-purity arsenic containing 30 ppm of impurities was allowed to diffuse from the gase- ous phase at 700°C into single crystals of p-type germanium containing 0.1 ppm of indium. As the arsenic diffuses into the P-type germanium, an n-type layer will form in the diffusion zone. At the p-n junction the concentration ratio of the arsenic to the indium is constant. Experimental Procedures—The germanium specimens, 10 mm by 10 mm by 5 mm, were polished and etched to a mirror finish. The specimens were then sealed off in a vycor glass capsule at 3 x 10"5 mm Hg pressure with a sufficient amount of arsenic powder to produce a one-half atm pressure of arsenic at 700°C. Specimens were annealed at 700°C without radiation. The diffusion coefficient determined from these samples agrees within 8 pct of previous work done by Fuller.' Three specimens were given diffusion anneals at 700°C in a small tube furnace centered beneath the target of a 2-mev Van de Graaff generator. The specimens when in the furnace were 10 cm directly below the target of the generator. These specimens were irradiated continuously during the diffusion run with the Van de Graaff operating at 2 mev with a tube current of 225 to 250 pamp. The intensity of the x-radiation at the surface of the specimen inside the furnace was approximately 4.5 x l05 roentgens per hr. The temperature was controlled within m2°C by a chromel-alumel thermocouple throughout this work with no observed temperature change due to the radiation. By careful lapping, the samples were polished at an angle of 5 deg to the diffusion zone, giving a XI0 increase in the visible diffusion zone. The location

Jan 1, 1960

By Robert M. Dreyer

Diamond is the hardest known material. The diamond industry is separated into two major segments: (1) industrial and (2) gem. The major industrial use of diamonds is as a high-grade abrasive in a wide variety of applications for which no effective low-cost substitute is available. Table 15.4C.1 gives data on diamond production and on United States diamond imports. In both gem and industrial diamond production, but especially in the case of gems, the quantity of stones produced is not directly correlated to value, for the determination of value is markedly affected by quality. South Africa long has been the world leader in gem diamond production with an estimated production in 1968 (including South-West Africa) of about 4 million carats, equal to 43% of world production. During the past decade there has been a marked rise in gem diamond production in the USSR, so that nation is now the second-ranking world producer, with Angola (Portuguese West Africa) third. In natural industrial diamonds, the major production comes from Congo-Kinshasa (former Belgian Congo) which had a production of 15 million carats in 1968, equal to 47% of world production. In the past six years, there has been a remarkable increase of industrial diamond production in the USSR, which now ranks second with a production of 6 million carats, equal to about one-fifth of world production. South Africa now ranks third followed by Congo-Brazzaville and Ghana. No natural diamonds are produced in the United States. Since the discovery of an economical method for synthesizing small diamonds, there has been a rapid increase in synthetic production from 4 million carats in 1962 (1 carat equals 200 mg) to 11.5 million carats in 1968. Table 15.4C.1 gives the gradually increasing imports of industrial diamonds and indicates a relatively stable price. In 1968, the imports of industrial diamonds were 13.5 million carats with a value of $59.2 million. Table 15.4C.2 shows the rapidly increasing imports of cut and uncut gem diamonds into the United States. In 1968 the United States imported 2.5 million carats of uncut stones with a value of $166 million and 1.5 million carats of cut stones with a value of $175 million. Diamond marketing is dominated by DeBeers Consolidated Mines, Ltd., which, through subsidiaries, controls many of the major African diamond deposits. More important economically, however, through its Central Selling Organization, DeBeers markets 86% of the non-Communist world's natural diamonds, including most of those derived from deposits outside of corporate control. In 1967 the mines owned by DeBeers produced nearly 8 million carats, and the Central Selling Organization sold over $600 million in gem and industrial diamonds. The dominance of diamond sales by

Jan 1, 1976

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith' and of A. G. H. Andersen .2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford," using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,1,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates h in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

The Carlin gold deposit is located in northeastern Nevada about thirty-five miles by road from the town of Elko. Following the staking of six square miles 'of ground, a drilling program outlined a fine ore body mineable by open pitting. The resulting mine turned out to be the largest open-pit gold operation in the world, until the Rosario Pueblo Viejo operation was started in 1975. Because of the high profitability forecast at the then $35 gold price, construction of a 2000 stpd mill was commenced on a crash program and was completed for Newmont Mining Corporation by Bechtel Corporation in ten months. Production was started in early 1965. The gold mineralization occurs in marine-type sediments, chiefly silt- stones and limey shales, and the ore characteristics make for a difficult materials-handling problem. At 5% to 6% moisture the ore is dusty during crushing, but even a light rain or snowfall virtually turns the material into a slurry. Crushing this sticky ore below 314 in. (19 mm) in the dry season and 1 in. (25.4 m) during the winter is extremely difficult and leads to problems with conveyors, chutes, and fine ore storage. The initial flowsheet for Carlin's crushing plant used a 5 ft by 22 ft (1.52 m by 6. 7 m) vibrating feeder -grizzly under the 60 -ton dump pocket for feeding the 42 in. by 48 in. (1067 mm by 1220 mm) single toggle jaw crusher and a 5 ½ ft (1.52 m) standard cone crusher in closed circuit with a 6 ft by 12 ft (1.83 m by 3.66 m) vibrating double - deck screen. Because continual packing of fines in the vibrating feeder pan would cause frequent plant shut-downs to remove the fines with jack hammers, the decision was made to replace the vibrating unit with an apron feeder and stationary grizzly ahead of the jaw crusher. A dribble belt was also installed under the apron feeder. This installation has greatly improved the feeding of the pit run ore to the .primary jaw crusher. Mining at Carlin is done by a 5 yd shovel and 7 ½ and 10 yd front-end loaders, and ore transport is by several sizes of trucks from 30 to 75 tons capacity. These pit haulage trucks dump onto stockpiles adjacent to the primary crusher. Ore is then fed to the dump hopper by front- end loaders only when the crushing plant is operating. This extra handling procedure is necessary because plant delays caused by problems with wet ore in the secondary crusher resulted in the ore setting up or packing in the dump pocket. Solidified material in the dump pocket would in turn delay truck haulage. The substitution of an

Jan 1, 1978

DeLamar, the largest silver mine in the United States outside the Coeur d’Alene District in Idaho, came into production in April 1977. It is a joint venture of Earth Resources Company and Canadian Superior Oil Co., with Earth Resources being the operator. The property is a consolidation of several old operations dating back to the 1800s; the better known of these are the DeLamar and Sommer-camp mines. DeLamar is situated in southwestern Idaho near the Oregon border in the Owyhee Mountains, 88 km (55 miles) southwest of Boise, Idaho. Heavy snowfalls and very low temperatures are common in the wintertime. Planned production was 77,500 kg (2.5, million oz) of silver and 5 13 kg (16,500 oz) of gold per year. Expected life at a milling rate of 1,540 mtpd (1,700 stpd) was 20 years, with an ore grade of 144 g Ag and 1.58 g Au per mt (4.2 oz Ag and 0.046 oz Au per st). Present production is at the rate of 1,900 mtpd (2,100 .stpd). The total cost to bring the mine into production was reported to be approximately $22 million, and the mill was reported to have cost about $10,000 per daily ton of design capacity. At DeLamar, naurnanite (Ag2Se) is the principal silver .mineral occurring with acanthite (Ag2S) disseminated through quartz veins and a silicified rhyolitic ash-flow tuff of Miocene age. The mineralization is relatively iron and manganese free and is readily amenable to cyanidation giving recoveries of 85% silver and 92% gold, which occurs free. When the plant was started, considerable difficulties were encountered in handling the wet sticky ore because of the high clay content. Following primary crushing, the ore is stockpiled. Due to the sticky nature of the ore, the vibrating feeders initially installed under the stockpile were replaced by a reclaim hopper and an apron feeder which was fed 24 hours a day by a front-end loader. The minus 200 mm (8 in.) ore is fed to a 5.5 m by 2.75 m (18 ft by 9 ft) autogenous mill followed by a 2.75 m by 4.57 m (9 ft by 15 ft) ball mill and cyclones. The mills are equipped with 750 kw and 520 kw (1,000 hp and 700 hp) motors. Both mills discharge to the same cyclone feed sump and a portion of the cyclone underflow is returned to the autogenous mill. Cyclone overflow, which is 20% plus 74 microns (200 mesh), is leached in four agitators in series for 72 hours (45 hours at the 2,100

Jan 1, 1981

By AIME AIME

THE outstanding event of the past month has been the conference in Washington of the representatives of about seventy-five of the leading national, regional and local engineering and allied technical organizations." Editorial-July Journal-The American Society of Mechanical Engineers. ?Prominent engineers from all parts of the country, representing more than 75 engineering societies, with an aggregate membership of more than 125,000, participated in the organization.? Editorial-July Journal-American Institute of Mining and Metallurgical Engineers. ?Civil, mechanical, electrical, mining, heating, sanitary, chemical, agricultural, marine, refrigerating, radio, fire protection, automotive, industrial and military engineers, as well as some architects and geologists assembled at Washington, D. C. to consider the advisability of organizing a national federation capable of bringing the united efforts of the entire membership to a focus on any problem of mutual interest." American Architect, June 23, 1920. ?"the object sought places it above any engineering gathering ever held." Editorial-American Machinist, June 17, 1920. "The youngest. profession has voluntarily accepted its responsibility in human affairs and is now reaching forward to a career of essential service." "This is .unmistakably the meaning of the Organizing Conference " Editorial-Industrial Management, July; 1920.

Jan 1, 1920

By NATHANIEI HERZ

(Cleveland Meeting, October, 1912.) THE formula very frequently used for computing the economical size of pipe to transmit compressed air is that of D'Arcy, as follows: d5(p1-p2)/w1l D-c w11 Where, D = the volume of compressed air delivered in cubic feet per minute,-at the final pressure. c = an experimental coefficient determined for the various sizes of pipe. d = the diameter of the pipe in inches. 1 = the length of the pipe in feet. P1 = the initial gauge-pressure in pounds per square inch. p2= the final gauge-pressure in pounds per square inch. W1 = the density of the air, or the weight in pounds per cubic foot at the initial pressure, p,. The most common case is that in which the given quantities are: the quantity of air required, the length of the pipe, and the initial pressure. The method of solution is to assume a pressure-loss and to compute the remaining factor, c/d5, thus giving the size of pipe corresponding to the assumed loss of pressure. It is always desirable to try two or more pressure-drops, in order to find the combination that is most satisfactory, since often a small change in the size of pipe will reduce or increase the loss of pressure several pounds. An alternative method is to assume a size of pipe and calculate the corresponding pressure-drop. Each method involves a series of tedious calculations to arrive at the most economical solution, and also requires the use of tables giving the constant, c, the actual diameters corresponding to the nominal pipe-sizes, the density of the air, w1, and often, for convenience, a table giving the

Dec 1, 1912

By Charles E. Lundin, Albert S. Yamamoto

The phase eqrtilibria of the binavy system, Nb-Al, weye established by metallographic, X-ray diffraction, hardness, and thermal-analysis techniques. Three intermediate phases were identijied, Nb3.41, Nb2Al, and NbAl,. The N6,Al and NbAl phases have extensiue ranges of solubility. The maximum solubility of aluminum in niobiuitz is 23.0 i0.5 at. pct (8.0 wt pct) A1 clt 1960" i 10°C. The maximumt solinbility oj niobiunz in alunzinutz is less than 0.3 i0.1 at. pct (1.0 tut pct) fib. The A'h,Al and Nbgl interinediate phases forr peritectically at 1960° 1UcC and 1870" i 1U9C, respectively, zuhereas the NbAl, phase fornts congvuently fio11t the melt at 1605" 10°C. A eutectic reaction oc- The intent of an over-all research program was to develop niobium-aluminide-base coatings for refractory metals since these coatings exhibit useful high- curs at 57.8 i 0.5 at. pct (28.5 wt pet) A1 and 1500" 10°C between NbAl and NbAl3. The aluminum-rich region of the system has a peritectic reaction where liquid reacts with NbAL, to form aluminum solid solution. Structural and lattice -pavarneter data /or the intermediate phases were determined by X-ray diffraction analyses. An unusual transfov?nation having charactevistics of nucleation-growth and martensitic nleclanisils occurs on cooling the niobium solid solution in the region from 18 at. pct (6 wt pct) Al to 23 at. pct (8 wt pct) Al. The transfornzed product on rapid quenchirzg is an acicular NhAl. temperature resistance to oxidation. As a prerequisite, the phase equilibria of the system, Nb-A1, were necessary. A literature survey revealed that the phase-equilibria data reported by various investigators were rather incomplete and conflicting. Therefore a complete determination of the system was undertaken by the authors from 0 to 100 pct of solute addition.' In 1959 Savitskiyz presented a tentative diagram which

Jan 1, 1967

By Arthur F. Daily

8.5-1. Bucket Line Dredge. INTRODUCTION. The modern bucket-line dredge for mining placer deposits is a combined floating excavating machine and a gravity concentration system. Material is excavated at the forward end by the buckets, elevated, washed and screened, concentrated for recovery of valuable mineral, and discharged off the stern as coarse and small fractions. The end product is a concentrate consisting either of the valuable mineral(s) and associated heavy minerals, which are taken to a treatment plant on shore; or in the case of gold, a clean amalgam ready for retorting. The bucket-line dredge may be adapted for purposes other than mining for valuable mineral by installing, in lieu of a concentrating system, machinery for pumping all of the solids ashore in a pulp, or for producing washed gravel in selected size fractions of which all or a selected fraction is pumped to disposal areas on shore or into side barges. The two principal types of bucket-line dredges designed for mining are: 1) those having an inclined belt conveyor stacker to discharge the coarse fraction of washed tailing well astern of the hull, and sluices to discharge the sand fraction (Fig. 8.5-1), and 2) those having only sluices for discharge of all tailing astern. Use of the latter type has been confined, with few exceptions, to mining cassiterite-bearing deposits in Malaysia and at sea off Indonesia. Small dredges having only flumes for washing and concentrating all material dug by the buckets have been used for mining shallow stream valley deposits. GENERAL ARRANGEMENT. The general arrangement of a modern bucket-line dredge for mining tin, with a primary concentrating plant on board, is shown in Fig. 8.5-2. The hull and superstructure of most dredges are fabricated of structural steel; wood also has been used for both small and large dredges with complete satisfaction. All-riveted or partially welded unit hulls have been widely used and are desirable for exceptionally severe service. The hull

Jan 1, 1968

By Robert Ammon

THE milling practice at Mascot, at present, consists of dry crushing to 5/8 in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per. cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. are made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads 3.55 Jig concentrates 61.30 Jig tails 0.80 Flotation concentrates 60.60 Flotation tails 0.09 Extraction 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows:

Jan 9, 1924

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By H. l. Burghoff, D. E. Lawson

The presence of tellurium in copper and, by inference, in copper alloys, has been considered seriously detrimental and has been avoided. In particular, very small amounts of tellurium have been found to produce red-shortness, although the effects on cold-working and ordinary physical and mechanical properties have not been known so definitely. References in the literature are few, but as long ago as 1881, Eglestonl reported that 0.083 per cent tellurium in fire-refined copper rendered the copper red-short and therefore worthless for hot-rolling. In hot-rolling copper cakes containing this amount of tellurium, he found that fine cracks appeared in the cakes on the first pass through the rolls, the cracks opening further in successive passes. When cold, the metal was said to be tough and malleable. A few years ago, during the course of an investigation in our laboratory on copper-base alloys, it was found that tellurium-bearing alloys could be machined much more freely than similar alloys not containing tellurium. The study was pursued further in this direction, and considerable data were obtained, which indicated that certain tellurium-bearing alloys might have properties of commercial interest. The work eventually led to patent protection,2 a wide range of tellurium-bearing copper-base alloys being covered. This article presents results obtained on the effect of tellurium on the mechanical properties of three copper-base alloys: commercial bronze (90 Cu, 10 Zn), 1.5 per cent tin bronze (98.5 Cu, 1.5 Sn), and silicon bronze (96 Cu, 3Si, 1 Zn). Several alloys were cast in each series, with tellurium content ranging from 0 up to about 1 per cent. The alloys were melted under charcoal in a clay-graphite crucible, using a high-frequency induction furnace, and were cast without undue difficulty in rod form, 15/8 in. in diameter. Charges for the zinc and tin series were made up from the following materials: cathode copper, electrolytic zinc, tin, and tellurium in slab

Jan 1, 1938

By R. P. Rothwell

The milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I hare thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value arid interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a met stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulplides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is managed in a skilful and economical manner, though the necessity for

Jan 1, 1880

By Robert Franke

(Butte Meeting, August, 1913.) IN view of the prominence which the conical mill has attained in the fine-crushing field .within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. . Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each. liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which. follow rolls crushing to 0.5 in.

Jan 7, 1913

By H. l. Burghoff, D. E. Lawson

The presence of tellurium in copper and, by inference, in copper alloys, has been considered seriously detrimental and has been avoided. In particular, very small amounts of tellurium have been found to produce red-shortness, although the effects on cold-working and ordinary physical and mechanical properties have not been known so definitely. References in the literature are few, but as long ago as 1881, Eglestonl reported that 0.083 per cent tellurium in fire-refined copper rendered the copper red-short and therefore worthless for hot-rolling. In hot-rolling copper cakes containing this amount of tellurium, he found that fine cracks appeared in the cakes on the first pass through the rolls, the cracks opening further in successive passes. When cold, the metal was said to be tough and malleable. A few years ago, during the course of an investigation in our laboratory on copper-base alloys, it was found that tellurium-bearing alloys could be machined much more freely than similar alloys not containing tellurium. The study was pursued further in this direction, and considerable data were obtained, which indicated that certain tellurium-bearing alloys might have properties of commercial interest. The work eventually led to patent protection,2 a wide range of tellurium-bearing copper-base alloys being covered. This article presents results obtained on the effect of tellurium on the mechanical properties of three copper-base alloys: commercial bronze (90 Cu, 10 Zn), 1.5 per cent tin bronze (98.5 Cu, 1.5 Sn), and silicon bronze (96 Cu, 3Si, 1 Zn). Several alloys were cast in each series, with tellurium content ranging from 0 up to about 1 per cent. The alloys were melted under charcoal in a clay-graphite crucible, using a high-frequency induction furnace, and were cast without undue difficulty in rod form, 15/8 in. in diameter. Charges for the zinc and tin series were made up from the following materials: cathode copper, electrolytic zinc, tin, and tellurium in slab

Jan 1, 1938

THE CHALRYAN.--I think that we have set the stage for the balance of the sym- posium. Most of the emphasis has been placed on the immediate value of every- thing we can do and everything we can learn for the furtherance of the war effort. I believe that ought to be first, but I also believe that this is the time for us to con- sider very seriously not only what these improved methods and techniques do to form a closer approach to ideal segregation but what effect these great quantities of scrap metals and alloys that are going to be produced this year and next, are going to have-what their impact will be-on post- war industry in general and in particular ,, on the primary metals fields. In some cases we have been hearing in the last month or two of the law of diminishing returns coming to the fore. We find alloy simplification growing and certain alloys being produced in great quantities, which will perhaps drop out of the picture some- what as the war ends but never to the lower ( stage they had before. We have I think a pretty good cross- section of the producers, the refiners, the reclaimers and ingot makers, the ultimate users here, and there ought to be some good and helpful discussion. The papers are open for discussion. Mr. Beattie, do you want to make any 1 comment? H. J. BEATTIE.*-To start the discussion I might ask Mr. Deitz what they do with manganese bronze turnings? We segregate the manganese bronze turnings from the other bronze turnings. The value of it seems to be much out of line with the price of ingot, that is, as compared to some of the other alloys like 88-10-2 or 85-5-5-5. I assume it is because they can only use a

Jan 1, 1943

By Glenn A. Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation's pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant. Cerro de Pasco Ores The ores of the Cerro de Pasco Copper Corpn. at Cerro de Pasco, Peru, are situated at an altitude of 14,000 ft. The town and mines are served by the Cerro de Pasco Railroad, which operates between Cerro de Pasco and Oroya, the site of the company's copper and lead smelters. Table 1.—Average Analysis of Cerro de Pasco Ores Pacos Ore Pykite Ore Silver, oz............................................... 10.3 12.0 Gold, oz................................................ 0.007 0.01 Lead, per cent........................................... 1.7 1.8 Copper, per cent......................................... 0.19 0.27 Zinc, per. cent........................................... 1.4 1.02 Iron, per cent........................................... 13.4 34.45 Silica, percent.......................................... 61.8 24.5 Alumina, per cent....................................... 2.5 0.62 Lime, per cent........................................... 1.5 0.20 Manganese, per cent..................................... 0.42 0.09 Sulfur, per cent,.......................................... 1.1 34.2

Jan 1, 1929

By Dale E. Walker

The Captain mine came into being under the following circumstances: 1) Commonwealth Edison had need for fuel for the generation of electricity in their Chicago service area. 2) Southwestern Illinois Coal Corp. had an ample supply of coal in the Illinois No. 6 and No. 5 seams. 3) The Gulf, Mobile & Ohio R.R. had a one-line transportation system with the capability of transporting coal from the Captain mine to Commonwealth Edison. These fortuitous conditions permitted an effective three-way partner- ship to develop. Commonwealth Edison had built a new generating station at Joliet, Ill., across the Illinois River from the existing station, to supplement their power-generating capacity for the Chicago area (Fig. 1). The annual requirement of the Joliet station is approximately 4.5 million tons of coal. From large reserves of coal in the No. 6 and No. 5 seams, Southwestern Illinois Coal Corp. contracted to supply Commonwealth Edison with approximately 6 million tons annually from its Captain mine. The logical carrier was Gulf, Mobile & Ohio, whose mainline travels through this coal field and also passes by the Joliet station on its way to Chicago. This railroad has been moving Southwestern's coal from the Streamline mine for more than 30 years. The basic ingredients of timing, scheduling, moving, and handling were adopted by the three parties, the precise details being worked out jointly. To do this, each group had to know its requirements exactly. The initial schedule was drawn up and tentatively approved, with each party taking a hard look at its own requirements and commitments to make certain that the schedule could be met on a normal daily basis. With only minor changes, the final schedule was adopted, each participant feeling that it had a sufficient factor of safety to maintain steady operation. Each party agreed to help the other in time of emergency. When a delay occurs in any part of the operation, the other

Jan 1, 1969