Search Documents

By Frank Firmstone

It is proposed to consider here only comparisons made between results obtained when the materials employed are precisely the same, two furnaces at the same works for example, or the same furnace under different conditions as respects temperature of blast, method of charging, etc. With this limitation, the most important point in the comparison is the amount of fuel consumed per ton of iron. This, in fact, is the only item in the prime cost of the iron which can properly be said to vary in consequence of changes in the furnace process; for of the other principal items, the ore used per ton of iron, and also the amount of fluxing material, will depend on its richness, which, under the assumed conditions, will be practically invariable when taken over any considerable period; the labor cost also, from its nature, should be very nearly constant when estimated on the ton of iron. Moreover, as it consists principally in handling and moving material, it is greatly affected by circumstances quite independent of

By R. T. Gallagher

FOLLOWING recent precedent, the Mineral Industry Education Division opened its first session on Sunday afternoon at the Columbia University Men's Faculty Club with an unexpectedly large attendance. The first session was presided over by the Division Chairman, A. F. Greaves-Walker. The first paper, a preliminary report on college enrollments in mineral technology curricula, by W. B. Plank, though incomplete, pointed to a general over-all reduction of 38 per cent in enrollment in mineral industry curricula. Following that, A. C. Callen's paper elicited many comments. It presented the results of a survey (no direct questions asked) addressed to officials in the mining industry. J. L. Bray spoke on war production drive methods and results and his slides gave visible evidence (and much laughter) of the success of the drive. C. L. Wilson's able presentation covered not so much present status but the future status of accelerated mineral technology programs after the war. The last paper of the first session by Edward Steidle, was handed out in mimeographed form.

Jan 1, 1943

By J. A. Hren, C. M. Wayman

RECENT investigators have noted anomalous behavior in the electrical resistivity of vanadium below room temperature. Rostoker and Yamamoto1 in studying the vanadium-oxygen system hypothesized that the body-centered-tetragonal phase existing from 15 to 34 at. pet O at approximately 800°K was really a low-temperature allotrope of vanadium that was stabilized by oxygen. In measuring the electrical resistance of cold-swaged vanadium rod over a range of temperatures, a small discontinuity was observed at approximately 240°K, supporting their notion of allotropy. However, the magnitude of the observed discontinuity was extremely small. Loomis and Carlson2 in studying the ductile-brittle transition in vanadium also made resistance measurements and reported a discontinuity near 200°K. More recently, White and Woods3 showed that the electrical resistivity from room temperature to approximately 100 °K was not linear and at variance with the Bloch-Griineisen law. Instead of finding a discontinuity, they observed a deviation from linearity below 200°K. In discussing their results they pointed

Jan 1, 1961

By Clyde Williams

A MAN who is a first-class metallurgist, engineer, and scientist and an outstanding organizer, administrator, and executive and who, at the same time, has an innate ability to "make friends and influence people" everywhere he goes is an exceptional personality at any time. And if such an individual can retain this combination of virtues during a great war despite the fact that the Government loaded him with enough work and responsibility for three such men. he is a most exceptional personality. And if he can keep his head and maintain an unfailing sense of humor during the trying war years and, while dealing with hundreds of jittery metallurgists and metalworkers, with Army and Navy brass, and with red-tape-entangled war agencies by the dozen, he is a rare personality indeed. Such a man is Clyde Williams, director of Battelle Memorial Institute. who will be President of AIME in 1947. The Institute is fortunate in having him as its mentor during what may be a critical and important year.

Jan 1, 1947

In traversing lately the Sierra Madre, west of Sail Pedro and Guanacevi, I estimated the topographic summit at several points, by aneroid barometer, at about 8,500 ft. Mr. Weed's measurements, 40 miles further north, are from 9,000 to 9,500 ft., and indicate the correctness of the impression I obtained at the time, namely, that the greatest movement in the elevation of the Sierra was between Guanacevi and Guadaloupe y Calvo. This is suggested also by the course of the headwaters of the Rio Conchas and of the Nazas, and by the relative corrasion of the branches of the two streams. Mr. Weed's statements as to the unevenness and great relief of the andesite floor underlying the later dacites and rhyolites are very interesting, and lead me to add that the floor of the andesite breccias and flows is uncovered for several square miles east of Guanacevi. This floor is of reddish, bluish and gray shales, lying horizontal or dipping slightly east. Their age is unknown; but from the interbedded occurrence of copper sulphides, I took it to be Triassic,

Jan 1, 1903

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.' It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method' of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author's results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By COREY C. BRAYTON

PACIFIC COAST steel and iron industries can now take care of all the western and export demands except for heavy structural shapes, thick plates, rails, alloy tool steels, and a few other items. In. 1902 all of our steel came from St. Louis and Milwaukee and points still farther east. A small quantity at that time came from foreign countries. Early mining in the West was, broadly speaking, prior to the steel age. 'Wood for structures and iron for castings were almost exclusively used. Forgings were made of rolled iron that came from the East and foreign countries. San Francisco was, from the early days of mining, the manufacturing center for mining and milling machinery of all types and held that position until the .nineties, when eastern competition began to be felt. Even today in the old mining camps of the West, and many abroad, you will find machines and equipment with familiar San Francisco manufacturers' names. ..Iron, either rolled or cast, entered into their manufacture, for steel castings did not come into general use :until the nineties.

Jan 1, 1929

By Chester Lee

Introduction THE Atlin Mining District is in the northwest corner of the Province of British Columbia. Ruby Creek, where the operation to be described is situated, is 17 miles east of the town of Atlin and about 18 miles south of the south line of Yukon Territory (Fig. 1). Gold was discovered in the district in January, 1898, and the production to date from placer mines has been $4,518,000, according to the reports of the Minister of Mines for-the province. Geology The essential points in the regional geology are given in the following paragraphs. Long erosion produced a plane-like surface slightly above sea level with a few peaks and ridges.1 A gradual uplift followed and. erosion increased, the streams cut deeper, the cuts so made being afterward increased by glaciation. The ice straightened and planed the slopes of the main valleys and widened and lowered their floors, in some cases flooring the valleys with silt, sand, gravel, and clay. As the glaciers rapidly retreated, lakes were formed.

Jan 5, 1916

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960

By Hsun Hu

C. G. Dunn (Geneva1 Electvic Reseavclz Labo,vatory)-Dr. Hu16 has obtained a number of rolling and annealing texture results that partly agree with those of Dunn17 and Dunn and Kohl8 for experiments of a similar nature. I would like to discuss some of the points of agreement as well as some of disagreement and then present some unpublished data as a contribution to the work on textures. Firstly, there is agreement on the components produced during a 70 pct cold-rolling reduction of a (110) [001 ] single crystal; there is agreement on the forma- tion of a (110) [001] recrystallization texture provided recrystallization occurs at 800°C or higher; and there is agreement on the formation of (120) [001] components provided recrystallization occurs below 600°C. There is some disagreement on the low-temperature recrystallization since I also obtained a substantial amount of a (110) [001] component while the author obtained only (120) [001] components. I also discussed the differences between low- and high-temperature recrystallization (which included further annealing changes in the samples on long

Jan 1, 1962

Discussion of the paper of E.. C. LEE, presented at the St. Louis meeting, October, 1917, and printed in Bulletin-No. 130, October, 1917, pp. 1825 to 1832. H. M. WILSON, Pittsburgh, Pa.-The statement ill the paper of T. T. Read, "Increasing Dividends Through Personnel Work;" that the offering of substantial money rewards for avoidance of accidents is much more effective than mere propaganda or education respecting accident prevention, is a, point fully substantiated in the experience of insurance inspection under workmen's compensation acts. The first year under the Workmen's Compensation Law in Pennsylvania, during which over 2000 mines were tinder the observation and protection of the inspectors of the insurance companies, has resulted in several inspections of each mine, a splendid cooperation .between the operators, the State mine inspectors and the insurance inspectors, and an average reduction in premium rate for insurance from $3.83 to $2.77, a reduction of more than $1 per $100 of payroll, on an average payroll of nearly $100,000,000, In other words, the insurance companies have

Jan 1, 1918

By J. Price Wetherill

The coal-seams that are worked vary from 3 1/2 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the general system pursued is to reach with a permanent outlet such a point in the seam as will

By Helmer Hedstrom

THE purpose of this paper is to direct attention to the importance and the usefulness of phase measurements in electrical prospecting for ore, a subject about which virtually nothing has been published. The paper describes a new field method for ore prospecting, the "Turam" method, which makes use of phase measurements, and which has been used with great success for five years. Of the principal geophysical prospecting methods, the gravimetric and magnetic methods determine the direction and strength of the static fields of force of the earth. By seismic and electrical methods, fields of force are applied to the block of ground under investigation. By these methods a third parameter can be measured, besides the direction and strength of the field; namely, the time of arrival of the applied field at the different observation points. This time of arrival has been practically the only parameter measured in seismic work, while in electrical pros-pecting it has generally not been considered, the measurements having been limited to determination of direction and strength of the applied field.

Jan 1, 1937

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1916 to Dec. 31, 1916. BOWMAN, Joseph V., Chem., Andes Copper Mining Co., Chanaral, Chile, South America. CALDER, NORMAN L., Min. Geol., Cia. Minera y de Fomento, Watkins, Fomento Prov. de Santa Clara., Cuba. CONRADS, RALPH A., Met. Engr., Magna Plant, Utah Copper Co., Garfield, Utah. FARR, T. H. POWERS, JR. Asst. Assayer, Argonaut Mining Coy Jackson, Cal HAURY, PETER S., Min. Engr ...Alta Loma, Cal. HOULE, ARTHUR, Supt., Shattuck-Arizona Copper Co., Box 2009, Bisbee, Ariz. LEIB, VICTOR E?, Min. Engr 4204 Ave. D, Austin, Tex. LINDSLEY, THAYER, Min. Engr 82 Beaver St.,. New York, N. Y. POTTER, OCHA Supt., Superior Copper Co., Houghton, Mich. ROCCA, BERNARD T.; Engr., Bluebell Mine, Cons. Arizona Smelting Co., Mayer, Ariz. SAFFOLD, RAY P P.'0. Box 436, Douglas, Ariz. THOMS, JAMES EZRA, Asst. Chief, Milling, -Roasting, Acid Depts., Mineral Point Zinc. Co., Depue, Ill. TOMITA, HARUYOSHI, Met. Engr., Mitsubishi Co., Osaruzawa Mine, Akita-ken, Japan.

Jan 2, 1917

By Robert Glass Cleland

THE CONNECTING link between Phelps Dodge and the copper mines at Bisbee and Morenci was a Canadian-born mining engineer and metallurgist named James Douglas. Judged by almost any standard, Douglas was an extraordinary man. Like John Muir of the California red- woods, he had in his blood "the heather and bog juices of Scotland," and the rugged virtues of a singularly great race. His father, for whom he was named, was a graduate of Edinburgh University, a member of the Royal College of Surgeons in London, and a man of rash and adventurous spirit. Extremely catholic in his intellectual interests and attainments, he was unusually skilled in his profession, certain-sometimes to the point of disastrous stubbornness--of his own judgments and decisions, careless of life or fortune where duty or moral issues were involved, and always deeply moved by the sufferings and misfortunes of his fellow men. The career of the senior Douglas included a curious medley of novel and adventurous experiences-prolonged hunger and cold while acting as surgeon on a Greenland

Jan 1, 1952

By C. W. Hill

IN a previous article preliminary experiments were described, indicating the possibilities of a quantitative spectroscopic method for the determination of small amounts of lead in copper, which would be accurate and rapid, and could be carried out in the refining plant by one not skilled in chemical analysis. The present paper deals with the development of the method in the factory, giving the details of apparatus and its standardization, and presenting a comparison of the accuracy of the method with that of the standard electrolytic determination. (For variations and other applications of the method, the reader is referred to the first article.) FIG. 1.-STEPS IN THE ELIMINATION OF LEAD. (The lead line, at point 105.8 in the violet portion of the spectrum, is seen between the two copper Lines,-102.29 and -106.29, lying close to the latter. The crowded faint lines are due to the carbon are.) 1. OUTLINE OF METHOD A carefully weighed sample (0.4 gm.) of the copper to be tested is placed in a cavity in a graphite positive electrode. An arc capable of

Jan 10, 1918

By Ernst A. Hauser

A few years ago an Indian native of British Columbia drew the attention of white men,' to a deposit of a claylike material on King Island, at the mouth of Dean River just opposite Hunter Island in the Pacific Ocean (Fig 1 ) . The native claimed that this natural product, which is found not in solid form but either as a paste or as a thick, viscous liquid, exhibited exceptional healing properties not only for various types of skin irritation but also for internal ailments. He pointed out that the natives had been using this material very successfully for generations. Since then, systematic surveys have revealed that the deposit, covered by a humus layer of varying thickness, is far more extensive than had originally been assumed. The product as mined today is of puttylike consistency and of greenish color. If exposed to air it dries rapidly, forming a slightly gray, rather brittle product, which does not permit redispersion to its original consistency. When the natural product is rubbed on the skin, however, the presence of coarse, sandy material is revealed.

Jan 1, 1952

By S. F. Emmons

The first paper which appears in the published Transactions of our Institute is that read by our respected Secretary at its first meeting in Wilkes-Barre in May, 1871. It is entitled " The Geographical Distribution of Mining Districts in the United States," and presents a brief but masterly review of what was known of the distribution of our deposits of useful minerals, particularly the metals, not only from a geographical but from a geological stand-point. At the request of Dr. Raymond I agreed, somewhat hastily, perhaps, to write for this occasion a brief sketch of the geological distribution of the deposits of the useful metals in this country, in the light of the increased knowledge of the present day. In the time given no personal investigation was possible, and as it was therefore out of the question to attempt to make anything that could be considered an original contribution to the history of our ore-deposits, I have been obliged to limit myself to an examination of such pub-

Jan 1, 1894

By F. L. Ransome

The dike here described is exposed in the workings of the Wedge and Bachelor mines, on the southern side of Red Canon, north of the town of Ouray, Colorado. Its course is north 80° east, or nearly east and west, and it hades to the north about 10°. It rarely outcrops, and was nowhere seen at the surface near the mines. A specimen collected by Dr. A. C. Spencer about two miles to the westward, near the mouth of Red Creek, indicates, however, a probable exposure of the dike near this point. The Wedge and Bachelor mines lie in a nearly horizontal series of fine-grained, light-grey sandstones, alternating with beds of very fine-grained shale of the same color. The shale as encountered underground is unusually compact and massive, but weathers readily on exposure, and splits much after the manner of ordinary shale. When fresh it closely resembles some finely arenaceous limestones, but it does not effervesce with acids, and is eseentially a fine, indurated, siliceous silt. Near the surface, and near the top of the sedimentary series as

Jan 1, 1901

By Francis J. Dennis

Many factors govern the value of dredging-ground, and much capital can be wasted by the mistaken policy of contracting for the purchase of property arid the installation of machinery before a thorough examination has been made. To the uninitiated investor the presence of gold is generally the criterion, and very superficial evidence is necessary to satisfy him as to this point. he couuiclers the comprehensive report of a competent engineer as a wasteful extravagance, aild cannot understand why the engineer requires so much time and money to ascertain the information on which to base his conalusions, when the promoter can furnish him such pleaaing and satisfactory data with but little expenditure of time aud money. The uninitiated investor will often optimistically risk capital for purchase and equipment, and riot uiitil the veuture comes to grief does he learn that the condition8 are wholly unsuited for dredging. In many instances, a short preliminary examination by a competent engineer would have disclosed these facts. The mere presence of gold is by no means suficient; sonie of

Jan 1, 1912