Search Documents

By H. l. Burghoff, A. I. Blank

The state of knowledge bearing on the stability of copper under stress at elevated temperatures is generally known to be in need of revision and extension. The present investigation, dealing with the creep characteristics of a deoxidized copper of low residual phosphorus content, is intended to contribute in some small measure toward this end. The experimental data presented herein have been correlated by methods of evaluation and interpretation familiar to those who are concerned with crecp of metals. In practice it is common, if not requisite, to use structurally stable materials at elevated temperatures. It is frequently desirable, however, to test materials under conditions that produce structural change, in order to determine the extent of such change and its effect on physical properties, thus making it possible to establish accurately the limiting conditions to which such materials may be safely exposed. The creep characteristics of the drawn copper wire of this investigation arc directly associated with its structural instability at elevated temperatures. Complete realization of this fact is essential to the evaluation of its creep resistance under various conditions. Creep results should apply to steady deformation under equilibrium conditions, but these are seldom attained in only one or two thousand hours. It will be shown that steady creep rate for copper at useful stresses does not usually begin until considerably more time has elapsed. A wholly satisfactory substitute or shortcut for extensive creep testing does not appear to be evident in the application of mathematical analyses to limited experimental data. Material A single lot of phosphorized copper wire was drawn down to 0.125-i11. diameter with a final reduction of 84 per cent. After mechanical straightening, a portion of this wire was annealed to an average grain size of 0.013 mm. in a controlled-atmosphere furnace. The composition and initial properties of the copper in these two conditions are listed in Table I. Photomicrographs of the original structure are shown in Fig. I.

Jan 1, 1945

By J. S. Diller

In 1827, chromite was discovered near Baltimore by Isaac Tyson, Jr., who initiated the mining of chrome ore an:! later (1845) .the manufacture of chromium compounds in this country. From 1828 to about 1860 the United States, supplanting Russia, supplied chromite for most of the world. Chrome deposits were found also in California, and the Tyson Company shipped ore to Philadelphia by way of Cape Horn. In 1848, J. Lawrence Smith, an American in the employ of the Porte, discovered large bodies of chromite in Asia Minor. They were developed in 1865 and became the chief source of the world's supply for a number of years. The discovery of the large high-grade bodies in New Caledonia, and later in Rhodesia, with other foreign sources, gives at present an abundant supply for all demands. For a number of years before the great war, the United States produced only a few hundred tons of chromite annually, for local use, but during the war the demand for domestic ore resulted in a production of more than 82,000 long tons of crude ore in 1918, and it was demonstrated that the United States has reserve deposits equal to a war demand of several years' duration. Now that the war is over, the country is conserving its domestic supplies by employing higher-grade but cheaper ore from foreign countries. ChromiUm-bearing Minerals Oxides: Chromite-—chromic iron ore................ FeO.Cr2O3 Picotite—chromic iron ore................. (MgFe)O.(Al,Cr) Chromates: Crocoite—lead chromate................... PbCrO4 Phoenicochroite—basic lead ohromite........ 3PbO.2CrO3 Vauquelinite—phospho-chromate of lead..... 2(PbCu)CrOd.(PbCu)3P2O8 Sulfates: Redingtonite—hydrous chromium sulfate.... Knoxvillitel—hydrous basic sulfate of chromium.............................. Daubreelite-—iron-chromium sulfide (known in meteorites only)...................... FeS.Cr2S3

Jan 1, 1920

By Max Mason

In 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which automatically and continually conveys messages from underneath. We also have available the earth's gravitational field which furnishes us

Jan 1, 1929

BASIC open-hearth slags have no obviously unique features when compared with slags from other metallurgical operations. Open-hearth slags form and exist at temperatures ranging from 2500 to 3100 F (1370 to 1700 C). In the course of an open-hearth heat, the liquid slag changes slowly and continuously in chemical analysis-the changes reflecting changes in temperature, changes in metal analysis, solution of charged materials, solution of feed additions, and solution of refractories. Throughout the process, the slag performs specific primary functions that are responsible for a large measure of the technical and economic importance of basic open-hearth steelmaking. It is intended in this chapter to present the chemical reactions by which the primary functions of basic open-hearth slags are carried out, to describe the physical and chemical principles governing the extent to which these reactions proceed and can be regulated, and finally to indicate the limitations imposed on other features of the process by the fulfillment of the primary functions. Basic open-hearth slags perform three primary functions. First and foremost, the slag provides a means of removing phosphorus from the liquid metal. The ability to remove phosphorus is largely responsible for the widespread use of the basic open-hearth process. Second, the slag serves as a controlling factor in transferring the oxygen required for the other oxidizing reactions. Third, the slag provides a means of eliminating some sulfur from the open-hearth bath. While the extent of sulfur removal is not comparable to that of phosphorus, the ability to remove some sulfur contributes much to the value of the process. The effectiveness with which the slag fulfills its functions varies with temperature and composition. Since operating temperatures are fixed largely by the specified nature of the product and the equipment, .the speed and extent to which the functions of the slag are carried out depend largely on its composition. The necessity for regulating slag composition to accomplish the re-

Jan 1, 1964

By Oliver Halston

THIS paper reports the results of the use of salt in some research work carried on during the past 3 years at the Salt Lake City Station of the Bureau of Mines, which is quartered in the University of Utah, whose Metallurgical Research Department cooperates with the Bureau. Only the work involving the use of salt is described. The authors wish equal credit given to J. F. Cullen, C. L. Larson, C. Y. Proutz, C. E. Sims, H. C. Neeld, R. W. Johnson, F. G. Moses, N. C. Christensen, and G. H. Wigton, who have all in some way contributed toward the success of this work. Lead Metallturgy Popularly Supposed to be Without Problems In bead metallurgy it is difficult at first to find metallurgical problems, as the prevailing conception has been that bead is so easily concentrated in its various ores and so easily reduced to its metallic form that the only progress possible is that involved in cheapening methods of mining and of reduction. Most of the problems usually considered are of minor nature and do not involve radical metallurgical changes. During the 3 years of work of the Salt Lake Station, the following classification of problems in the metallurgy of bend has been made: Those involving Oxidized Ores. 1. Ores containing only bead. s. Ores containing bead and silver or gold. 3. Ores containing bead and zinc, with or without silver. Sulphide Ores. 1. Ores of pyrite carrying some bead. 2. Ores of complex zinc-bead-iron sulphides. 3. Complex sulphides containing in addition precious metals.

Jan 8, 1917

By G. E. McElroy

Much attention has been directed to mine-air flow in recent years, more especially in Great Britian where there is frequent reference to a theory of fluid flow developed by English engineers. Briefly stated, this theory is that for similar passages of the same relative roughness, in which fluid flow occurs, the conditions of flow are exactly the same for W D V equal values of the product where W = density of the fluid, D = diameter of the passage through which flow occurs, V = mean velocity of flow, and p = absolute viscosity of the fluid flowing. This, the "Reynolds Criterion" of fluid flow, had its origin in the work of Reynolds1 more than 40 years ago. Later, Rayleigh2 amplified the theory which has been conclusively proved for small pipes by the experiments of Stanton and Panne13 over a large flow range, and by Lacey4 over a somewhat more limited range. Concordant results on small pipes have also been obtained by numerous other investigators with single fluids over more or less limited ranges of flow. According to this theory, results in one medium, such as water, are immediately applicable to another, such as air; and experimental results on models are (theoretically, at least) applicable to full-scale designs. This is of great importance in aeronautics and can be of considerable value in mine ventilation research. Hodgson, in a recent paper,6 has outlined the application of this theory to mine-air flow and recent English experiments6 on the resistance of a timbered mine airway have been expressed in this form.

Jan 1, 1927

By J. J. Gilman

IT is well established that dislocations exist in crystals and account for crystal plasticity.' However, the origins of the dislocations are not clear. Among the means by which dislocations might originate are: a) through crystal growth accidents, b) by the collapse of condensed sheets of vacancies, or c) by stress-induced nucleation. Theoretical calculations' have indicated that the last means should require very high stresses in order to operate. The purpose of this paper is to show that the stresses around the tips of cracks are large enough to nucleate large numbers of dislocation loops. Specifically, it will be shown that (100) cleavage cracks in LiF crystals nucleate dislocations in regions of the crystals where dislocations did not exist previously. It is believed that the use of LiF for this investigation does not restrict the significance of the 1 results. In fact, it is believed that this complements and extends previous papers by the same author which dealt with metal crystals.10,14 The dislocations were detected by means of the etching techniques that were described in a previous paper by Gilman and Johnston.3 In that paper it

Jan 1, 1958

By Paul G. Raffinot

I. INTRODUCTION We are aware that as a general rule zinc and lead deposits located by the Mediterranean Sea contain important proportions of oxidized ores of lead and zinc (cerussite, anglesite, smithsonite, hemimorphite). Although their economical significance is decreasing in favor of totally sulphurous ores*, la Societe Miniere et Metallurgique de Penarroya and its subsidiaries are still operating four small oxidized ore-bodies in Morocco, Spain, France, and Italy (see Figure 1). Not all of these deposits contain exclusively oxidized lead and zinc ores but also sulphides such as galena, sphalerite, and pyrite. However, the very presence of the oxidized ores gives the treatment methods their characteristics and it is bearing this in mind that we think the description of these four mills worthwhile. Flotation remains the basic process. It uses sulphurization in alkaline medium and long chain xanthate in order to concentrate lead minerals (amylxanthate) and fatty amines (sterarylamine acetate) to concentrate zinc minerals.

Jan 1, 1970

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By Y. C. Liu

An analysis is presented to show that the formation of rolling textures in fcc metals can be rationalized in terms of flow mechanisms operative during the rolling process. First, a general approach used by Calnan is followed, where the rolling process is approximated on the basis of two axes, p and Q. In this treatement there are two separate sets of slip systems, one for each axis, and it is shown that a homogeneous rotation can he achieved by restricting the slip systems for the two axes to share common slip directions Then, two criteria are used to select the active slip systems for the axis P: they must have relatively high resoloed shear stresses, and dislocations on these slip systems must interact attractively in order to lower total energy content Finally, a method of analysis is introduced to locate the end position of an axis by knowing its acti7.e slip systems. The result of the analysis indi- cates that two main flow mechanisms operate in fcc metals. The ideal orientation derived from one oj-them is (8 13 21) (21 8 13) which is very close to the (358) (523) orientation observed experimentally on the rolling texture of copper. This flow mechanism should only he operative in metals containing dislocations extended into partials separated by less than five times their lattice parameter. The ideal orientations derived from the other flow mechanism are a combination of (1 10} (112) and a spread of orientations with (110) parallel to the rolling plane. This type of ideal orientations corresponds to those observed in the rolling texture of silver 30:70 brass, and binary alloys with high alloying content. This flow mechanism should be operative in any fcc metal regardless of its stacking-fauIt energy. When a polycrystalline metal is subjected to a large amount of plastic deformation, it is generally observed that grain orientations alter and align themselves towards certain positions, eventually reach-

Jan 1, 1964

The early history of coal in West Virginia is all included with that of Virginia in the few records available but for present-day readers it is much more convenient that the account of this area prior to the Civil War be grouped with that since then. West Virginia shares with Maryland in the first record of coal noted in the Appalachian fields. This was along the upper Potomac River, in the fall of 1736, and the data about it are given under Maryland, as most' of the development of the area was in that state. The next record of coal was left by John Peter Salley in his account of the expedition he made with Howard and others in 1742. (See p. 17.) The next reference found is that of Dr. Thomas Walker, in 1750, when he passed through the Pocahontas coal field. This has been described on page 18. Six years later, in March 1756, Capt. William Preston, who was with Major Lewis in his expedition down Big Sandy River, wrote in his journal: "Tuesday 2.... Moved down the branch and- came to the main creek where we camped. Put on half rations. Came into the Cole land; crossed the river 8 times."1 The party crossed from the head of Clinch River to Horse Pen Creek, then to Jacob's Fork and down it to Dry Fork of Tug River; the coal was seen in what is now McDowell County. The early settlers must have known of the presence of the great Pittsburgh bed in the northern part of the state, both along the Monongahela River and elsewhere, because the outcrops could easily be seen along streams in many. places. The report of the Commissioners for Adjusting Claims to Unpatented Lands, made in 1789, contains several references to coal in the names of streams, made years earlier. The earliest is one for 1,000 acres to James Walker, in Monongalia County, "adjoining his settlement on a branch of the right hand fork of Pappaw known by the name of the Stone Cole Lick made in the year 1773."2 Another of 400 acres in the same locality was settled upon in 1777.2 A third spoke of a tract "on the left hand fork of Stone Cole about three miles from the mouth," in 1783.1 Monongalia County then covered all of the northern

Jan 1, 1942

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min. is required to drain and dress the furnace hearth, make up the tap hole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays, because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of' charge. Such general considerations are dealt with first. GENERAL CHARGING PRACTICE Charge materials are discussed in detail in Chapter IV; the present chapter is concerned with the charging, melting, and proportioning of the raw materials in the various types of furnace practice. Charging Equipment and Stock Handling. The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment described in Chapter I (see also Fig. 18, page 33). It is generally desirable to charge the scrap about as fast as the physical volume can be got into the furnace. A limiting factor may be the height to which the scrap may be piled in the furnace without deflecting the flame to such an extent that it will impinge on the roof or walls and thus damage the refractories, but light scrap may often be piled up near the roof since the flame usually "cuts it down" rapidly before impingement on any roof area can persist long enough to do appreciable harm. When the nature of the scrap and the handling facilities are adequate to meet the aim of rapid charging, little thought is given to this feature of operation. Unfortunately, at times

Jan 1, 1944

By Irving A. Palmer

During the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part, no doubt, to the scarcity of papers written on the subject. 'There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 1, 1915

By Leonard C. Grimshaw

Diffusion of carbon from gases into iron has been the object of much research, because of its long recognized importance in carburizing processes, but the direct diffusion of carbon from steel into iron has received relatively little attention. Because of the increasing use of clad metals in industry, direct diffusion from steel into iron is becoming of practical importance. Therefore, the object of this investigation was to study the diffusion of carbon from several different kinds of steel directly into relatively pure iron, realizing that elements in the steels other than carbon might influence the rate of carbon diffusion. The previous work on diffusion of carbon into iron has been considerable, and includes many reports in foreign languages. This work has recently been well reviewed by Mehll and Krynitsky12 and the reader is referred to their excellent bibliographies. Methods of Study There are two main methods by which the direct diffusion of carbon from steel into iron may be studied. In one method, steel is first decar-burized in part, and diffusion of carbon then allowed to take place from the steel into the decarburized steel. This method is open to two serious objections: (1) the decarburized steel is not iron, but contains elements such as manganese, silicon, chromium or tungsten, which may be an essential part of the steel under study, and which may seriously influence the diffusion of carbon into the decarburized area; (2) there is from the start of diffusion an unknown carbon-concentration gradient between the steel and the decarburized area. Another method, which possesses neither of these disadvantages, is to study diffusion from steel into a thick plating of electrolytic iron. Herc the chief difficulty is to secure an electrolytic deposit of iron upon steel without introducing an oxide film at the interface that will interfere with diffusion. The author is able to deposit iron upon any kind of steel without introducing an oxide film at the interface, so that diffusion of elements from the steel into the iron is free to proceed unhindered.

Jan 1, 1938

By Leonard C. Grimshaw

Diffusion of carbon from gases into iron has been the object of much research, because of its long recognized importance in carburizing processes, but the direct diffusion of carbon from steel into iron has received relatively little attention. Because of the increasing use of clad metals in industry, direct diffusion from steel into iron is becoming of practical importance. Therefore, the object of this investigation was to study the diffusion of carbon from several different kinds of steel directly into relatively pure iron, realizing that elements in the steels other than carbon might influence the rate of carbon diffusion. The previous work on diffusion of carbon into iron has been considerable, and includes many reports in foreign languages. This work has recently been well reviewed by Mehll and Krynitsky12 and the reader is referred to their excellent bibliographies. Methods of Study There are two main methods by which the direct diffusion of carbon from steel into iron may be studied. In one method, steel is first decar-burized in part, and diffusion of carbon then allowed to take place from the steel into the decarburized steel. This method is open to two serious objections: (1) the decarburized steel is not iron, but contains elements such as manganese, silicon, chromium or tungsten, which may be an essential part of the steel under study, and which may seriously influence the diffusion of carbon into the decarburized area; (2) there is from the start of diffusion an unknown carbon-concentration gradient between the steel and the decarburized area. Another method, which possesses neither of these disadvantages, is to study diffusion from steel into a thick plating of electrolytic iron. Herc the chief difficulty is to secure an electrolytic deposit of iron upon steel without introducing an oxide film at the interface that will interfere with diffusion. The author is able to deposit iron upon any kind of steel without introducing an oxide film at the interface, so that diffusion of elements from the steel into the iron is free to proceed unhindered.

Jan 1, 1938

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

By H. M. Chance

Adequate treatment of the difficulties surrounding the valuation of mineral lands requires that agreement be first reached defining value as understood for the purpose of appraisal. To define value as the price of a product is not sufficient, and does not assist us in using the factors that cause variations in values and in relative values. The real value of any product depends primarily upon its relation to the necessities, comforts and pleasures of mankind. As the necessities, comforts and pleasures of the civilized races differ from those of more primitive man, the value of products varies with the degree of civilization and the environment of the consumer. Coal has no value to the savages of warm climates, and arrow-head flint none to the residents of New York. It has long been recognized that what has been termed " intrinsic value " must be limited to materials that are essential to existence—air, water, food. But " intriusic value" cannot be measured in monetary terms. The intrinsic value of a bushel of wheat is due to the fact that it will support the life of an individual for a certain definite time, but this fact does not enable us to measure or to express that value in monetary terms. It has often been proposed to adopt as a measure of the value of any product the quantity of labor necessary to produce it, but this method is of limited application, and will not apply to what may be termed " intrinsic values." For many reasons it might be well, while assenting to the fact that any material may be intrinsically valuable, to abandon the use of the term " intrinsic value." One of these reasons is the tendency to confuse the idea of intrinsic value with a value that is conferred by economic conditions, that is purely artificial and that may be permanent or evanescent. Intrinsic value must from its nature be permanent and unchangeable. Possibly for present purposes the value of any material may be considered as having a dual origin: First, that due to economic

Jan 1, 1914

By Victor Homerberg

A STUDY of the correlation of the mechanical properties, and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the manufacturer. The results obtained by Babson and Buhler,1 Bengough and Hudson,2 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470° C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200° C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a ¾ -in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 3, 1924

By A. R. Troiano, A. B. Greninger

There is need for an adequate working hypothesis that would describe at least qualitatively the crystallographic mechanism for the transformation from austenite to martensite in steel. A general theory would not only be of great assistance in the correlation of existing data and in planning future experimentation, but would also form the basis for an eventual explanation of the property changes that accompany lattice transformations. The mechanism of martensite formation described in the following pages is the outcome of two new experimental determinations: (1) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite, and (2) the measurement and analysis of the change in position that a volume of austenite undergoes when it transforms into a crystal of martensite. For this latter study, the stereographic analysis of shear was employed; this method greatly simplifies the solution of lattice-shear problems, and some space is devoted to its description. Lattiice Relationships and Habits PREVIOUS WORK The lattice relationships between austenite and martensite in carbon steels have been studied by Kurdjurnow-and Sachs,' and by Wassermann;2 and in iron-nickel alloys by Nishiyama.3 Wassermann,2 and Mehl and Derge.4 The studies by Kurdjumow and Sachs and by Wassermann were made on single (austenite) crystals of quenched 1.4 pct carbon steel, and the results of these two independent studies agree closely with the postulated lattice relationships: (III)r||(0ll)a [101]r [111]a [1] Both Nishiyama and Wassermann worked with an alloy of iron plus 30 pct nickel (all austenite at room temperature), and "martensitic alpha" was formed by cooling in liquid air. They agree that the lattice relationships for these conditions are: (lll)r||(011)a [112]r[011]a [2] Mehl and Derge worked with a range of iron-nickel alloy compositions centered about 30 pct nickel. They concluded that when the transformation takes place near room temperature or above, relationship [l] holds, but if the same specimen is made to transform at -195°C, relationship [2] obtains;intermediate temperatures evidently produced a combination of these two relationships. Sachs and co-worker~,1,7 as well as Nishiyama,3 have proposed transformation mechanisms for martensite formation.* Both of the mechanisms picture the transformation as initiated by shearing movements along the octahedral [Ill] plane of austenite, followed by suitable expansion and contraction to complete the transformation. These mechanisms have been described and commented upon by Mehl, Barrett, and Smith,8 Mehl and Derge,4 Wassermann,2 and others, and generally accepted by investigators in this field. Greninger and Troiano9 have recently published the results of a detailed study of the shapes and orientation habits of martensite crystals in plain-carbon and nickel steels. They found that, contrary to previous assumptions, martensite plates form not along the octahedral planes but along austenite planes of very high indices; these results were in line with those of previous studies of martensite reactions in nonferrous alloy systems by Greninger and coworkers.6,10 Greninger and Troiano concluded that the transformation theories of Kurdjumow and Sachsl and of Nishiyama3 are untenable. Phragmén11 reached a similar conclusion. EXPERlMENTAL METHODS The object of this particular study was the evaluation of (1) lattice relationship between austenite and martensite, and (2) relationship between the martensite lattice and the martensite plate. The technique used for solving these problems was similar to that used by Greninger6 on martensitic structures in 8 copper-aluminum alloys. Briefly, the method consists of grinding and polishing a specimen on a surface parallel to an individual martensite plate and thus exposing a single martensite crystal for an area of l to 3 mm. The orientation of this exposed martensite crystal is then determined by means of a back-reflection Laue X ray pattern.12 Another pattern is obtained from the matrix crystal, and a stereo-graphic plot of data from these two patterns then provides the solution to the problem. It is necessary to repeat this process on several crystals in order to determine whether or not the solution is unique.

Jan 1, 1950

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleys1 and Gathmann,2- who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1964