Search Documents

By C. D. Stahl, E. E. Templeton, R. F. Nielsen

It has been customary, in predicting saturation changes, to use the Leverett fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's1 statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counter-/low with which to test the theory. A 4-ft sand-packed tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, alter which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. INTRODUCTION The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. field4 and laboratory5 data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. 2-3 It has been customary to use fractional flow rates instead of actual flow rates in displacement calcuIations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et a1,3 and by Fayers and sheldon,2 actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty.

By J. G. Y. Chow, S. B. McRickard

The tensi1e properties of Ferrovac iron have been studied from 4° to 300°K. The stress required for macroscopic yielding was found to he constant below approximately 50°K. The effect of mechanical twinning on this low -temperature stress plateau was investigated. The onset of twinning occurs in this iron between 130° and 150°K and depending on its previous thermal history the twinning-stress curue may drop below or remain above the vield-stress curves as the temperature is lowered. Twinning has been shown to initiate slip in quenclzed iron at low temperatures. In no instances, however, did the onset of twinning alter the continuity of the yield stress -tempwature curve. Our data shows that carbon inhibits twinning and slip at low tem-peratures. This observation nay be used to explain the ductile-to-brittle transition in iron. The effect of fast neutron irradiation on yielding and embrittlement in iron and Fe-C alloys is offered as supporting evidence for this viewpoint. THE mode of yielding in iron at low temperatures was studied in an attempt to find an expression based on a single mechanism to describe the thermal dependence of the yield stress of iron. There are two types of inflections observed in the variation of the yield stress with temperature in iron and Fe-C alloys. The first is associated with ductile behavior and consists of a region extending 50" to 100°K above absolute zero in which the yield stress is independent of temperature. The second is observed in more brittle materials such as Fe-C alloys and irradiated iron and consists of an abrupt discontinuity in the yield curve as the temperature is lowered through a ductile-to-brittle transition point. The temperature dependence of the yield stress for iron with four grain diameters as found in this study is shown in Fig. 1. To varying degrees all the curves appear to flatten or approach an asymptotic value as the temperature is lowered below 50°K. Several other investigators1,2 have observed a plateau in the yield stress of iron and steel at low temperatures and in 1956 Louat3 presented a theory which contained an explanation for this behavior. In a subsequent exchange with Erickson and Low4'5 who attributed the plateau to the onset of mechanical twinning Louat8 showed that twinning first occurs in iron and steel tested in tension at temperatures as high as 140°K which is well above the observed plateau in yield stress. Furthermore he pointed out that both twinning and slip are basically dislocation processes and that with modified parameters his original theory still applied when deformation is initiated by twinning. Variables which affect the ductile-to-brittle transition in iron are test temperature, strain rate, composition and grain size.7 LOW,8 Hahn et al.,9 and Hull10 have provided evidence which links brittle fracture at a given temperature with the specimen grain size and the onset of twinning. In fact, Hull equates the brittle fracture stress to the twinning stress. On the other hand brittle fracture has been observed in the absence of twinning and priestnerl1 has given a fracture criterion which is valid whether or not fracture is preceded by extensive twinning. The data presented here clarify the role of twinning in the low-temperature deformation of iron. Strong evidence is given that the amount and distribution of interstitial impurities such as carbon are of

Jan 1, 1965

By J. T. Norton, N. J. Grant, A. M. Gervais

An investigation of the creep deformation of coarse-grained high-purity aluminum at temperatures approaching the melting point permitted the formulation of a theory of subgrain formation. Subgrain boundaries were found to be formed by two different processes: kinking and polygonization. Polygonization is considered as the main factor in subgrain formation. SINCE "slipless flow" was first discussed in detail by Hanson and Wheeler,' many studies have been undertaken to determine how metals deform at high temperatures. Several types of observations have been reported. Jenkins and Mellor,² working on the creep of mild steels and various grades of commercial irons, found metallographic evidence of a kind of substructure within the grains after deformation at high temperatures. Homes" observed after creep deformation of steel at high temperatures that the original X-ray spots were sharply divided into several small ones. The same phenomenon was reported by Hirst4 from his studies on lead and later by Crussard5 from his work on aluminum. The works of these investigators demonstrated beyond any doubt that the splitting of the X-ray spots was due to the fact that the grains underwent a division into subgrains during deformation at high temperatures. Since then, numerous experiments have been undertaken on aluminum in order to determine the mechanism of formation of subgrains. Research workers can be divided, for the purpose of discussion, into two different groups as regards thinking on subgrain formation. On one hand, based on the work on polygonization by Cahn,6 Guinier and Lacombe,7 Greenough and Smith," Crussard,10,11 and Servi, Norton, and Grant," it was concluded that subgrain formation was a consequence of the simultaneous effects, first, of inhomogeneous deformation which produced bending of the lattice, and second, polygonization. On the other hand, Wood and coworkers13-16 based their work on the results of an earlier report" which dealt with crystallite size and a fragmentation theory. It is interesting to note that while Greenough and Smith8 and Wood et al. performed similar experiments, their conclusions were quite different. Wood et al. did not recognize polygonization as a fundamental mechanism and said that aluminum, at the beginning of the deformation, fragmented immedi- ately into subgrains in order to permit deformation of the metal, the number of these subgrains being a function of strain rate and temperature. They concluded that deformation of grains occurred by flow along the subgrain boundaries. In view of the contradictory conclusions, it would appear that the data were not explicit enough to provide an unambiguous conclusion. It appears that the techniques by which most of the results were obtained, namely, X-ray work, were not enough by themselves to solve the problem. Another approach was needed. In the present research, therefore, an extensive metallographic study was planned to supplement the X-ray work. The importance of revealing the subgrain boundaries metallographically was realized, and this will explain the extensive development and use of etching techniques. In order that subgrains would be considerably larger and therefore more readily visible under a microscope, the creep experiments were performed at very high temperatures approaching the melting point of aluminum. Development of Experimental Technique Creep tests were run at constant load on high purity (99.995 pct) aluminum specimens having a very coarse grain size. None of the specimens was run to fracture. The specimens were originally round (diameter, 0.187 in.; gage length, 1 in.) and had parallel flats milled in the gage section to permit

Jan 1, 1954

By J. B. Clark, A. S. Yue

PfANN1 has shown that when a cylinder of molten binary alloy freezes directionally, the solute distribution can be described analytically by cg=k(l-g)k-1 [1] in which Cg is the solute concentration in the solid at the point where a fraction g of the original liquid has frozen and Co is the initial solute concentration. The term k is the effective distribution coefficient of the solute and is defined as the ratio Cx/CL where Cl is the solute concentration in the main body of the liquid. Both the slope and the intercept at -log (1 - g) = 0 of a logarithmic plot of Eq. [I.] provide a measure of k. Under conditions of freezing where diffusion in the solid is negligible and the solute concentration in the liquid is uniform, the effective distribution coefficient k, derived as above, is equal to the equilibrium distribution coefficient taken from the phase diagram. However, under ordinary freezing conditions, even though solid-state diffusion is negligible, the solute rejected from the freezing solid does not have sufficient time to diffuse uniformly throughout the main body of the liquid. A concentration gradient is formed in a boundary layer in front of the advancing solid-liquid interface as pointed out by Rutter and Chalmers.' Thus, under these conditions, the concentration of the freezing liquid in the boundary layer is higher than that predicted from the equilibrium phase diagram and consequently the effective distribution coefficient k, obtained from directional freezing experiments, is larger than the equilibrium distribution coefficient. The symbol k will designate the effective distribution coefficient in the discussion which follows. In this paper, the determination of the effective distribution coefficient is demonstrated for several dilute binary alloys and a polynary magnesium alloy. The effect of freezing rate on the value of the derived k is presented in detail. An example for the calculation of the solidus in a dilute binary solution using the experimentally determined effective distribution coefficient is given. MATERIALS STUDIED Binary magnesium alloys of copper, nickel, and zinc containing approximately 0.10 wt pct solute and a polynary alloy containing approximately 0.10 wt pct each of several elements were selected for study. The spectrographic analyses of these alloys are given in Table I. The analyses are believed accurate to within +5 pct of the stated value. EXPERIMENTAL PROCEDURE Extruded rods of the alloys, 3/8 in. in diam and 11 in. long were used for directional freezing studies. The alloy rods were melted horizontally in a high-purity graphite boat by a Nichrome-wound tube furnace which moved parallel to the length of the rod. The boat was supported inside a Vycor tube suitably connected to provide a protective atmosphere of dry SO2. For an experimental run, the following procedure was used. The alloy rod was cleaned in dilute HNO, and dried. The graphite boat containing the alloy rod was placed within the Vycor tube and the tube connected to the gas train' The 'ystem was purged for 20 min with dry argon and then a flow of dried SO, was maintained for the duration of the run. The movable furnace was positioned and either all or a desired portion of the alloy rod was melted. After attainment of steady-state temperature gradients the molten bar was solidified from one end to the other at a controlled rate by pulling the furnace along the length of the bar at the desired speed. At the conclusion of the run, the directionally frozen alloy rod was analyzed spectrographically at 1 1/4-in. intervals.

Jan 1, 1961

By D. F. Stoneburner

The thermoelectric power and electrical conductivity of a series of liquid alloys of thallium were determined in order to study the relation of chemical bonding to semiconduction in liquids. The results indicate metallic behavior for the alloys of thallium with arsenic, antimony, and bismuth, while the sulfides, selenides, and tellurides indicate semiconduction. The results are compared with the Properties of the same alloys in the solid state. This work supports the observation that long-range order is not a necessary requirement for semiconduction. PREVIOUS work1,5 has shown that some sulfides and oxides behave as semiconductors in the liquid state. Although the band theory has been of great help in understanding the properties of solid semiconductors, its quantitative application to liquids is difficult. The very existence of liquid electronic semiconductors shows that ascribing the discrete structure of the energy spectrum to strict lattice periodicity, or long-range order, is not always satisfactory. Rather, the short-range order determines the structure of energy levels and the width of the forbidden gap and, consequently, the concentration of free holes and electrons. This is borne out by the analysis of data accumulated by Regel and coworkers.6 The similarity of electronic structure of liquid and solid phases of certain liquid metals was pointed out by Knight et a1.,7 who examined nuclear resonance in solid and liquid Li, Na, Rb, Cs, Mg, Al, Ga, Sn, and Bi. They found noticeable changes in the electronic structure upon melting only in the cases of bismuth and gallium. They concluded that "a liquid metal possesses a band structure which is very like that of the solid, provided the short-range structure is not altered during melting." In semiconductors in which the near-neighbor arrangement remains the same on fusion, the material would be expected to retain its semiconducting properties. The quantum theory of semiconductors, with its band structure of energy levels, is linked exclusively to long-range order. Furthermore, it has limited usefulness in predicting new semiconductors. Many sulfide8-12 have made comparisons of properties on the basis of crystal structure or the position in the periodic table, both methods involving the same factors as chemical bonding. Mooser and Pearson8"10 have pointed out that crystal structure depends on chemical bonding, and that this bonding is a property of the atoms themselves. As the periodic arrangement of the atoms offers an easy comparison of such factors as atomic weight and number of valence electrons it provides clues to expected similarities of bonding for various elements or groups of elements. This approach has led Mooser and Pearson to formulate their valence-bond theory of semiconduction, in which they define a semiconducting bond. These authors state that "semiconductivity is the result of the presence in a solid of predominantly covalent bonds. These lead, through the process of electron sharing, to completely filled s and p orbi-tals in the valence shells of all atoms of elemental semiconductors while in semiconducting compounds only one atom of any two bonded together need acquire closed s and p orbitals. The presence of empty 'metallic' orbitals in some atoms of a compound does not destroy the semiconductivity provided that these atoms are not bonded together; it may, however, give rise to pivoting resonance in

Jan 1, 1965

By F. E. Jaumot, A. Sawatzky

IT as long been recognized that there is a need for accurate systematic data on diffusion in solids. Originally, such data were needed to check existing theories but, more recently, it would appear that it could be used most advantageously as a guide to, or a check for, much needed extensions of the theory of diffusion. The awareness of the conditions which are important to experimental accuracy, the availability of the materials for accurate experiments, and the techniques have improved to the extent that it would now seem to an experimentalist that, unless extensions of the theory are made which take into account the fundamental parameters of the atoms, the electrons, and the lattice in some detail, the field of diffusion will rapidly become an empirical or semi-empirical field. The present series of experiments was designed to provide accurate data on the diffusion of the elements of the IB and IIB subgroups in silver; that is, to provide data on the diffusion in silver of three face-centered-cubic elements with roughly similar chemical properties, but with different atomic or ionic sizes and, similarly, for three noncubic elements. The elements of these two subgroups have different valences, so that the data will not give any significant information on differences due to the crystal structure of the solute. The present paper reports data on the diffusion of copper and mercury in single crystals of silver; the data for the other elements of the IB and IIB subgroups were reported previously by the authors1'2 and by Tomizuka and Slifkin.8 Experiment The general technique used was identical to that previously described1,2 and will not be repeated here. In all cases, the sectioning technique and high specific activity isotopes" were used. The short half-life of Cu64 made decay corrections more important than for the other isotopes, and necessitated around the clock shifts while data were being taken. Each section was counted at least twice (as was true for all longer half-life isotopes) and a monitor was counted along with each sample. Data for the diffusion of mercury in silver are presented at a greater number of temperatures than for the other solutes. This is a result of two circumstances. First, six (of 30) samples had to be discarded because of pitting or recrystallization which occurred during the diffusion runs, even though the samples had sustained high temperature prediffusion anneals. Either of these was a very rare phenomenon in the other experiments, and their occurrence in this case is considered in more detail below. Second, the curves of the logarithm of the activity of the sections vs the square of the penetration deptht were, in general, quite good, but frequently seemed to show one point to have high activity and the next point to have slightly low activity in terms of the best straight line. When this occurred, there was remarkable regularity of the high-low sequence. In any event, the results, as far as diffusion coefficients are concerned, were not affected by this amalgam effect. In fact, the mercury data had the highest internal consistency of any of the data. Results Diffusion of Copper in Silver—-Diffusion runs were made at eight temperatures In the temperature range from 700° to 950°C, for times ranging from 5 to 45 hr. A linear curve of the logarithm or the activity vs the square of the penetration depth was obtained for all samples. Table I summarizes the results for individual samples and Fig. 1 gives a plot 02 the logarithm of the diffusion coefficients as

Jan 1, 1958

By H. R. Stahi

THE ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classifiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9 1/2 -in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3 ½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 5 2 ¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1 3/4in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges are renovated occasionally, broken pieces being removed and the charge brought up

Jan 1, 1945

By C. R. Van Hise

Introduction.............29 The Three Zones of the Lithosphere ..30 Zone of fracture............31 Zone of flowage............ 31 Factors influencing depth at which flowage occurs.. 32 Zone of combined fracture and flowage.. 33 The Water-Content and Openings in Rocks....36 Condition of rater in the zone of fracture.. 36 The openings in rocks...........38 Size and number of openings..... 40 Ore-deposits derived from zone of fracture..45 The source of underground water......... . 47 The cause of the flowage of underground water..47 Belts of underground circulation.. 51 Upper belt of underground circulation.. 51 Lower belt of underground circulation.. .... .52 Capacity of water for work in the lower belt of underground circulation........... 53 Movementsof water in the lower belt of underground circulation. 54 The preferential use by water of large channels.. 60 Physico-Chemical Principles Controlling the Work of Under ground Waters..........62 Chemical action............63 Underground aqueous solutions..64 The relations of solution and temperature..... 65 The relations of solution and pressure..66 Precipitation........... 67 Precipitation by change in temperature..68 Precipitation by change in pressure..69 Precipitation by reactions between aqueous solutions.. . 69 Precipitation by reactions between liquid solutions and solids. 70 Precipitation by reactions between gases and solutions. and solids............71 The General Geological work of Underground Waters.. . 71 Division of the zone of fracture into a belt of weathering and a belt of cementation............72

Jan 1, 1901

By W. Hurst

What is entailed here is the extension of the sinzplified material balance formulas to encompass interference between oil fields. As previously reported, the ex-plicitness as so revealed for the cunzulative pressure drop as a function of all factors contributing to its change in the material balance equation, is now transcribed through the inter-conzmunicating aquifer to effect an increased pressure drop on an adjoining field by interference. Such is performed by mathematical analyses and the application of the Laplace transformations. What is accomplished is that the reiteration problems previously associated with interference studies are nullified, since volumetric changes for the fluids in situ are automatically adjusted by the explicitness so expressed, and what pertains to the superposition principle applies only to the impeded water drive upon a su.bject field, which is likewise incorporated in the over-all pressure drop that results. The mathematics treats with the rigorous solution of the problem, as well as with methods easily amenable to numerical interpretation by the practicing engineer. In all cases, however, what is deduced for areal extents, reveal interference between wells when time becomes large that further substantiate the analyses. Probably of equal significance, all variables and for/nation characteristics are accounted for. This applies to the differences in PVT analyses that occur from field to field and the physical parameters associated with the lithology of the reservoirs. The latter is deduced from a rigorous interpretation of the unsteady-state flow problem for sands of different permeabilities in series. Thus, what purports to be a trial-and-error calculation to include variations in sand conditions within the intercommunicating aquifer to define water drive has little importance compared to the designation of such paranzeters at the reservoir to constitute the essential criteria. INTRODUCTION In a recent publication, the reader has been introduced to the simplified material balance formulas,' It has been shown that the complexities formerly associated for identifying and determining reservoir pressure in the material balance relationship can be resolved by treating with the Laplace transformations, the inversion of which reveals pressure as an explicit function of all factors contributing to its change. For an under saturated oil reservoir, this constitutes an integrated effect from the inception of production; and for a saturated oil reservoir, such represents a survey traverse. However, what is most important, for the first time we are able to express the pressure change in a reservoir directly to the oil, gas and water produced, and to the physical parameters of the formation, in the same manner that reservoir pressure has served in the past to define well interference — which opens up this avenue of endeavor for investigating interference between oil fields. The occurrence of interference is by virtue of the juxtaposition of two or more oil reservoirs producing in the same aquifer. Thus, in any one field, the extended production so incurred creates a pressure lowering in the field, as well as in the aquifer, which can now be transcribed by these simplified material balance formulas to the adjoining reservoir to observe the increased pressure change so induced. These effects are retroactive from field to field, to reveal a pressure drop far in excess of normal depletion to evidence the interference pattern that can result. Such is the purpose for the present undertaking — to develop the mathematical physics treating with this phenomenon of interference between oil fields, employing the simplified material balance formulas. Since Ref. 1 often will be referred to in the text, it is identified as "The Simplification", in the same connotation that another paper has been referred to as the "Laplace Trans-formation. However, the amount of material to be covered in these passages is substantial; therefore, the total emphasis will be placed upon developing these fundamental ideas treating with interference rather than attempting to offer work curves, which always can be prepared. For the practical application of these simplified material balance formulas that form the framework of the present development, the reader will find a comprehensive treatment in the Appendix of Ref. 1, illustrating a factual field example. In essence, what is proposed by this presentation is to make available to the practicing engineer a simplified means to treat with interference between oil fields, independent of the complex machine computations that have attended such undertakings in the past. As the problem unfolds, a common pattern will be discernible, whereby the many reiteration processes that previously required computing devices are eliminated.

By Henry Rawdon

THE RELATION between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An intercrystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows.

Jan 2, 1920

By J. D. Ridge

The geologic setting and mineral relationships of seven European massive sulfide deposits that more or less conform to the bedding of the largely noncal-careous sedimentary rocks and/or bedded volcanics in which they are found are considered here. These orebodies consist largely of massive beds or lenses of sulfides usually surrounded by halos of disseminated sulfides and distorted by tectonic activity. The formations containing these deposits have been metamorphosed in varying degrees at times subsequent to their lithification. The ore-forming process is thought to be essentially volcanic, with the ore constituents being brought to the shallow-water site of deposition through tectonic fissures from magma chambers at depth as gases or relatively concentrated hydrother-mal solutions. Certain European ore deposits of base metal sulfide have previously been considered to be of hydro-thermal or magmatic origin, but today a number of European mining geologists consider them to be syngenetically produced. In an effort to provide American geologists with some idea of the reasons behind this change in thought, the geological settings of seven of these deposits have been studied. These are: Ldkken, Meggen, Rammelsberg, Ergani-Maden, Outokumpu, Boliden and Roros. These deposits lie in bedded rocks that have undergone metamorphism from causes not universally agreed upon; most of the formations were originally shales, and may have been intercalated with limey and occasionally quartzitic beds, volcanic tuff, agglomerate, extrusive lavas and usually basic intrusives. Deposits of the conformable type, however, are not confined to these rock types but may be in calcareous and associated igneous rocks or almost entirely in volcanics. These deposits may be closely associated in space with igneous rocks that, again, are usually basic types. Although the ages of the enclosing rocks range from mid-Precambrian (Boliden and Outokumpu) to Eocene (Ergani-Maden), the bulk of them are Paleozoic, with two (Meggen, and eammelsberg) being upper middle Devonian and two (LØkken and RØros) being Cambro-Ordovician. Geographically, two are in West Germany, four in Scandanavia and one in Turkey. Of the seven deposits, six are mined for copper, with three of these also producing zinc, and two lead; one is mined for zinc and minor lead. In the discussions of the seven conformable deposits that follow, I have attempted to present as uniform a treatment as their varying characters will permit. For each deposit, I have considered the stratigraphy of the area, its major structural characteristics, the form of the orebodies, their mineral content, and the origin of the ore. In the last of these subdivisions, I have presented only the viewpoint of those who believe the ores to have been formed by syngenetic processes, processes that went on at the same time as those which produced the beds that enclose the ores but that are not, in the deposits in question, thought to have been sedimentary in the strict sense of the term. The materials of which these orebodies are composed, it is suggested, did actually collect by falling through sea water to the floor of that portion of the sea in which they accumulated. The ore constituents, however, are believed by a considerable number of European geologists to have been added to the sea water from intratelluric sources, probably igneous magma chambers, as exhalations — hydrothermal solutions or volcanic gases. The effect of the encounter with sea water on these ejected gases or water-rich vapors was to precipitate their potentially solid constituents with great rapidity; they were deposited so quickly, in fact, that the amounj of normally accumulated mechanical or chemical sediment deposited over the same period of time was essentially negligible. The ores formed in this manner, however, are generally interbedded with normal sediments or with lava flows, or with any combination of these two types of rock-forming materials. Such departures as these deposits may have from their original mineral content and attitude are thought to be directly related to the degree of dynamic or static metamorphism that they may have undergone after their accumulation. I have not attempted here to present alternate hypotheses to that of so-called exhalative sedimentation although, of course, such exist and, in my

Jan 1, 1963

By L. L. Melton, W. T. Malone

Fluid mechanics research conducted with non-Newtonian fluid systems now permits prediction of the behavior of these fluid systems in both laminar and turbulent modes of flow through circular pipes. Present work concerns non-Newtonian fluid systems currently used in the hydraulic fracturing process. During fracturing treatments, an unsteady-state condition may frequently be encountered arising from. the reaction rate of a chemical additive. This condition must be evaluated in order to predict the actual behavior of a particular fluid during field application. Design and operation of the apparatus used to determine fluid-flow behavior permit obtaining data under such non-equilibrium conditions. This paper shows methods used to obtain rheology measurements, develop hydraulic relationships and evaluate chemical reactions producing unsteady-state conditions. Engineering application of this research is illustrated by employing measured rheological values and developed hydraulic retationships to produce frictional pressure loss (psi/100 ft) us flow rate (bbl/min) charts of common tubing and casing sizes for an example fracturing fluid. How these charts and chemical reaction rate information are then combined to predict actual turbulent hydraulic behavior during unsteady-state field conditions is also discussed INTRODUCTION Many fluids used in hydraulic fracturing contain chemical additives which impart non-Newtonian fluid properties that may drastically alter their hydraulic behavior. Equally drastic alteration in wellhead pressure, injection rate and hydraulic horsepower requirement may result from these fluid properties. Prior research conducted to relate non-Newtonian fluid properties with hydraulic behavior has not as yet produced a universal relationship, particularly for the turbulent flow region. which of the many Possible non-Newtonian fluid properties is responsible has not been conclusively established. A systematic description, suggested by Metzner, of the many possible non-Newtonian fluid properties exhibited by real-fluid behavior, and a current discussion of theoretical and applied aspects of non-Newtonian fluid technoloy can be found in Handbook of Fluid Dynamics. f Little or no research has previously been attempted with fluids exhibiting time - dependent properties. Addition of chemicals during a fracturing treatment is often accomplished by continuously mixing and displacing the fluid. This produces a time-dependent effect or unsteady-state condition while the fluid is progressing through surface and wellbore conductors. This condition is due to solution or chemical reaction of the additive. Considerable departure from conventional methods of obtaining and interpreting data was found necessary to consider these conditions. Therefore methods were developed to obtain hydraulic behavior information under these complex, unsteady-state conditions. Relationships presented in this paper to predict hydraulic behavior of non-Newtonian fluids in circular pipes were obtained by constructing and operating a small pipeline apparatus in the manner of a pilot-plant study. These relationships are suggested as scaleup equations and are not proposed as fundamental rheological parameters. While perhaps deficient from a fundamental research viewpoint, a pilot-plant study does permit the determination and convenient evaluation of variables pertinent to a process. A pilot-plant study can result in a valid engineering application procedure even when fundamental relationships are still undefined. An excellent series of articles by Bowen has appeared in the chemical engineering literature.2-8 These give a thorough review of proposed hydraulic relationships and their limitations for non-Newtonian fluid behavior in circular pipes. A graphical method is presented to scale up data for a fluid exhibiting an anomalous hydrau1ic behavior in the turbulent flow region. Considerable assistance has been obtained from these articles to interpret the anomalous behavior noted during this investigation. These articles also provided assurance that a pilot plant is a practical approach to evaluate the hydraulic behavior of non-Newtonian fracturing fluids. _____________

Jan 1, 1965

By J. B. Clemmer, P. E. Churchward, C. Rampacek

A cyclic method for processing manganese ores using sodium sulphate as the basic reagent is described. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte-containing agentisdescribed.Sodiumsulphuric acid and a catholyte-containing iselectrolyzedincaustic soda, a part of which is carbonated in a cyclic manner to form soda ash. The reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant todissolvethemanganeseandtheimpuritiessolution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate gives a high grade product and the carbon dioxide is returned to the carbonation step. The results of laboratory tests using cells equipped with synthetic-fiber diaphragms and permselective membranes, which permit transfer of anions or cations during electrolysis, are described. A METHOD which has been considered for pro-cessing manganese ores under emergency conditions to recover a product suitable for smelting to ferromanganese involves reductive roasting of the ore for leaching with dilute sulphuric acid followed by precipitation of the manganese from the purified pregnant solution with sodium carbonate. Although the process is operable and involves no novel or untried steps, it is noncyclic in regard to reagents. Research seemed warranted to determine if a cyclic process could be developed by electrolyzing the sodium sulphate formed during precipitation of the manganese with soda ash to regenerate sulphuric acid and sodium hydroxide. Reduced ore would be leached with acid anolyte to dissolve the manganese. The iron, alumina, and other dissolved impurities would be precipitated with the caustic catholyte, and the manganese in the purified pregnant solution would be precipitated as artificial rhodochrosite with carbonated catholyte to regenerate simultaneously sodium sulphate for electrolysis. Waste boiler gas and CO, from calcining the manganese precipitate would be recycled for carbonation of the caustic catholyte. There is a surprising lack of data in the technical literature on diaphragm electrolysis of sodium sulphate. One of the more comprehensive papers, by Atwell and Fuwa, describes the problem involved in electrolyzing byproduct sodium sulphate from the viscose process with particular regard to the design and operation of asbestos diaphragm cells. Frisk' also investigated electrolysis of sodium sulphate from viscose-spinning baths to recover caustic soda and sulphuric acid. The objective in these investigations was to produce, by electrolysis and evaporation, a concentrated caustic-soda solution and a sulphuric-acid solution low in sodium sulphate. Because of these requirements, the process was not too attractive despite a favorable yield of caustic and acid with a reasonable power consumption. Because strong acid and base are not required for processing manganese ores and nonelectrolyzed sodium sulphate is not objectionable in either reagent, the present problem was somewhat simpler than that of these investigators. The purpose of this report is to summarize briefly the results of laboratory electrolysis of commercial sodium sulphate in diaphragm cells of different types and the application of the acid and caustic for processing manganese ores in a cyclic manner. Electrolysis in Permeable Diaphragm Cells The principal problem in electrolyzing sodium sulphate in a permeable diaphragm cell is to prevent mixing of the acid and base formed in the anode and cathode compartments. It is not enough to separate the anolyte and catholyte by a single diaphragm. A three-compartment cell in which the sodium-sulphate solution is fed to the center compartment and flows through the permeable diaphragms to the anode and cathode compartments is more efficient electrically. Diaphragms should be porous enough to allow flow of solution to outer compartments but tight enough to prevent gross mixing of the anolyte and catholyte. In addition to being resistant to acid and alkali, the diaphragms should offer minimum resistance to the flow of current. It is also important that the electrolyte contain a high concentration of sodium sulphate to furnish an abundance of sodium and sulphate ions and thereby decrease the current carried by hydrogen and hydroxyl ions. A practical limitation of sodium-sulphate concentration is imposed by the decreased solubility of sodium sulphate with decreasing temperature. At 20°C, a concentration of 200 g per liter sodium sulphate can be maintained. Little is gained in conductivity by using a concentration greater than 200 g per liter. The small-scale continuous electrolysis tests were made in a 12x12 in. open-top bakelite cell equipped

Jan 1, 1956

By H. Y. Bassett

THIS paper attempts to show the various major operations used in nonferrous tube mills and does not necessarily represent the current practices at the two plants of the Wolverine Tube Div., of Calumet and Hecla Consolidated Copper Co. Inc. The operations now utilized in the production of tubing are quite varied and show the continual interest and advance metallurgically and mechanically to produce the best quality at the lowest cost. Naturally, any advance or lowering of cost is dependent on large production runs, which mean longer machine running time with maximum worker productivity. Standardization of tube sizes and elimination of unnecessary alloys are therefore very necessary, otherwise the development of costly new production machines would be of little benefit to the consumer as a whole. It should be noted that in such a short presentation it is impossible to describe in any detail the major operations. The short descriptions, it is hoped, will enable all who are interested to obtain a general idea of present, day practices in the copper tube producing field. Fig. I is a flowchart or sequence of operations showing the steps usually employed in tube production. RAW MATERIALS Quality starts with the raw material, and it is absolutely necessary that raw material be controlled and held to rigid specifications. Little need be said, however, regarding the raw materials for the casting of bars or billets, as the material always is purchased and checked against the various governing A.S.T.M. specifications. CASTING Casting, as is indicated in Fig. I, is quite varied and for convenience can be classified into two groups: The casting of solid billets, and the casting of hollow tubes, each of which is the base for subsequent operations. In the melting of the raw materials various types of furnaces are used, and the selection of any one is dependent on many factors outside the scope of this paper. However, as of general interest, a short description will be made of each. Induction Furnace (Low Frequency) This is popular in the melting of copper-base alloys, Fig. 2. In the induction furnace the principle of an inefficient transformer is used for the production of the necessary melting heat. The primary coil is.arranged around a transformer core made of high permeability silicon steel sheet. The secondary circuit is through a melting channel around the primary coil and opens into a hearth which contains the main charge. The heat is generated only in the melting channel, but because of the stirring action there is a constant flow of metal around the channel, which when mixing with the charge causes very rapid melting. The volatilization losses are very low as the furnace atmosphere above the charge is heated only by the heat from the melting metal. The stirring action, however, makes the use of any slag cover difficult. Such furnaces- must be started with molten

Jan 1, 1951

W. 0. HOTCHKISS, * Madison, Wis.-It was fortunate, in a way, that this subject of income taxation came up during the war when the government could appeal, on the basis of patriotism, to men of large, business experience to undertake the work of formulating this matter and practically donate their services. At any other time the government would have been unable to secure the necessary number of men of like ability. There is one thing that must not be forgotten. In all cases, except the very largest and most important, the application of this income tax law to a mine is going to be made by clerks whose salaries are fixed by a Congress that appropriated a half billion of dollars for a war purpose and provided that $4000 should be the highest salary paid in the adminis-tration of that great sum. The Congress of the United States unfor-tunately seems almost entirely unaware of the fact that men of ability and experience are worth money and must be paid adequately if proper public service is to be secured. While the formulation of the broad plans for administering the law have been in the hands of. men of unusual ability, we have the future to guard, and, if possible, the mining industry should see to it that the Internal Revenue Department is permitted by Congress to pay salaries that will enable it to secure men of the ability and experience necessary to insure proper consideration of the industry. Another fact to which I would call attention is the difference between the business and the economic, or economists', points of view as to what a mine is. The economists have properly, from their point of view, classed a mine as a wasting asset, but the average metal mine is not a wasting asset if it is a real mine. The economists are correct in a broad sense in that every ton of ore taken out diminishes the orebody by that amount. When it comes to the consideration of an individual mine from the business standpoint, the future of that mine rests on unfore-seeable events-the discovery of new orebodies or the development of old bodies beyond the point of probable expectations. Every going mine must develop new ore each year to replace that extracted, and, .during all but the last one or two years of its activity, actually does so. Instead of being a "wasting asset" such a mine, from the practical stand-point which must control valuation, is an "increasing asset." From

Jan 12, 1919

By C. D. Demond

IN reverberatory smelting, fuel is the chief item of expense, as it commonly is in processes using large percentages of it. Hence the most suitable supply is eagerly sought; that is, the supply which, in the end, yields the greatest net profit. The better grades are not infrequently bought, even at an advanced price, because they are apt to be decidedly more economical. High price, of itself, however, is no merit, for freight is generally the largest part of the cost of fuel, and the nearby supply may yield as high efficiency as that from a greater distance. If a poorer grade is reasonably good, and if its cost is low enough to more than offset the decreased technical efficiency, it is of course the more suitable. Any smelting, operation depends for both efficiency and economy on raising the furnace atmosphere considerably above the "critical" temperature; that is, above the temperature at which smelting is completed. If this temperature is not exceeded, smelting stops, no matter how much coal is burned; and the real value of a fuel depends on the number of degrees that the temperature is continuously kept above this point. For example, if one fuel maintains 2,500° F. and another only 2,100° F., while the "critical" temperature is 2,000° F., the first is worth at least five times as much as the second, although the increase above atmospheric temperature is only one-fifth more in one case than in the other. This "margin of temperature" above the smelting point is much more significant than the total number of heat units developed from the fuel. The case is parallel to that of water flowing from a pipe. The reservoir may contain a billion gallons of water; but, even though the fluid has come to the nozzle, not a drop will run out, where it can be of practical use, unless the level in the reservoir is higher than the nozzle; and the speed and volume of flow depend on how much higher the level is in the reservoir than at this point. If the temperature inn a furnace is not above the critical level there will be no slag to flow over the skimming plate, even though there are enough heat units to bring an unlimited quantity of charge up to the point of slag formation; and just as the value of a water supply for the purpose of putting out a fire depends largely on the effective head, so the difficulties of furnace management

Jan 8, 1914

By F. Kurata, P. C. Davis, T. L. Gore

An experimental method and apparatus for the study of the low-temperature phase and volumetric behavior of volatile mixtures are described. The phase diagrams, including the critical points, and the volumetric behavior of a natural gas and a mixture of the natural gas with methane at temperatures from -40°F to -200°F and pressures to 1.200 11si are givrn. INTRODUCTION Knowledge of the phase and volumetric behavior of mixtures of the light hydrocarbons at low temperatures is becoming increasingly important as interest in low-temperature separation processes increases. Distillation at low-lemperatures has been used for some time to recover ethane and ethylene from natural gas and refinery gas for petrochemical uses. Removal of excess nitrogen from natural gas by distillation has been proposed as a means of increasing the capacity of gas transmission lines and of improving the marketability of the gas.1,2 Evaluation of the latter process has been hampered, however, by the scarcity of data from which the phase behavior of natural gases at low temperatures might be predicted. While existing correlations of vaporization equilibrium constants may be used to predict the behavior of such mixtures at lower pressures, high-pressure computations often require knowledge of the location of the critical point of the system involved. Although correlations have been developed for the prediction of the critical temperature and pressure of certain types of hydrocar-bon systems, they do not apply to very volatile systems such as nitrogen-bear-ing natural gases. This paper describes the initial stages of an investigation of the low-temperature behavior of a numher of natural gases and other gases of commercial interest. The experimental method and apparatus are described. and the phase and volumetric behavior of a natural gas and a mixture of the natural gas with methane are presented. PREVIOUS WORK The published low-temperature vapor-liquid equilibrium data for hydrocarbons and mixtures of hydrocarbons with nitrogen and helium are listed in Table I. Most of these data are for binary systems, and the data of Stutz-man and Brown" at 100 psi are the only data on a natural gas. The data of Bloomer and Parent3 on the methafie-nitrogen system, which have been phblished since this study was completed, are a valuable addition to the knowledge in this field. Prior to the publication of these data the only published critical point data on systems having critical temperatures below the ice point were those of Ruhemann.1 on the methane-

Jan 1, 1952

By Norman Goss

IT is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.1-8 The broadening of the K. lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the dif-fraction lines are broadened and the K a doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolu-tion of the doublet is lost when a metal is cold-worked and the Lane spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attrib-uted the hardening to fragmentation of the grains into smaller units.

Jan 1, 1940

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By J. D. Forrester

Many have been prone to credit the decline of professional interest in some branches of mineral industry education to the industrialists and other agencies who use our graduates. We hear the cry that industrial salaries are too low, opportunities for advancement do not exist, and the mineral industry specifically and generally is not interested in the engineer's efforts. Perhaps the time now has come when we should "dress-ranks," examine our practices, and publicize and encourage advanced technical training instead of laying all our troubles elsewhere. There can be no doubt but that industry is interested and stands ready and willing to co-operate. This is demonstrated by the numerous grants-in-aid and co-operative industrial projects which have been made available to those relatively few schools which have been encouraging graduate study and research. There is no dearth of research problems in any of the mineral industry fields and the sooner we realize the great opportunities for constructive, technical research in all areas of our profession the sooner we will reap the benefits of our engineering enterprises by closer liaison and broader understanding with industry. An analysis is offered here of the status of graduate work and research in various phases of mineral industry education in the United States. It is

Jan 1, 1949