Search Documents

By C. S. Barrett

THE crystal imperfections known as faults in stacking (stacking disorder) are of importance to both fundamental and applied science and are receiving increasing attention. On the theoretical side there have been recent advances in the analysis of diffraction patterns in terms of stacking faults, and on the experimental side it has been found that certain metals develop a faulted structure on cooling through a phase transformation. Beyond this, little is known of what may be called the physical and mechanical metallurgy of faulting, although there has been no lack of discussion and conjecture as to the presence of faults in metals and the effect of faults on mechanical properties and microstructures. In the close-packed metals the nature of faults can be described very simply. Face-centered cubic (FCC) crystals consist of close-packed layers of atoms, (111) planes, stacked above each other in a definite manner. If one layer is designated as the A layer, the next must be a B or a C layer; that is, every atom of the second layer lies not above the atoms of the A layer, but nestles in the hollows between these, using the hollows designated as the B positions, or the equivalent hollows designated as C. If the sequence of layers is ABCABC...., so that layers three spacings apart are directly over each other, the crystal is FCC; if CBACBA ... it is an FCC crystal that is a twin of the former; if ABAB........or BCBC..it is hexagonal close-packed (HCP). A fault is a break in the sequence, such as ABCABABC .. . which has the effect of inserting an HCP lamella into an FCC crystal. Regularly spaced faults spaced two layers apart would convert an FCC crystal entirely to HCP, or an HCP to FCC. A fault in an FCC crystal is also equivalent to creating an FCC twin of minimum thickness; in fact, the entire crystal would be converted to its twin if faults were introduced regularly. (In HCP crystals, however, twinning does not occur on the basal plane and a fault on this plane is not identical with a thin twin). Faults are one of the possible causes for annealing twins,' for the strain markings that are brought out by etching deformed metal,'," for the altered X ray reflecting power of metal at slip bands that is revealed in X ray reflection micrographs,' for the extinction of Kikuchi lines in electron diffraction patterns, and for the hardening of latent slip planes.' Since other explanations of these effects are also available," there has been no direct proof of faults from deformation; yet it has appeared likely that they would occur. Faults resulting from phase transformations in metals, however, have been clearly revealed by diffraction in cobalt" and lithium. It is to be expected that the faulting tendency is greatest

Jan 1, 1951

By H. J. Ramey

Conventional calculation of total system isothermal compressibility for a system containing a free gas phase involves, among other things, evaluation of the change of oil and gas formation volume factors and the gas in solution with pressure. Preferably, this information should be obtained from laboratory measurements made with particular oils and gases. Often, experimental measurements are not available. In this case, it is necessary to obtain pressure-volume-temperature relationships from general correlations such as those of Standing' for California oils. In order to speed estimates of compressibility, generalized plots have been prepared of the change of both oil formation volume factors and gas in solution, with pressure from Standing's correlations. A generalized plot for estimating the change in the two-phase (oil and gas) formation volume factor with pressure is also presented. Usually, the effect of gas dissolved in reservoir water upon the total system compressibility is neglected for gas saturated systems, due to the low solubility of gas in water. Results of this study indicate that the increase in total system compressibility caused by solution of gas in water is often as large as the compressibility of wafer, and can be magnitudes larger for low pressure systems. Generalized results for estimating the change of gas in solution in water with pressure are presented in tabular and graphical form. INTRODUCTION During the past decade, pressure build-up and drawdown techniques have gained an important place in reservoir engineering. Build-up and drawdown analyses are only two special applications of the broad field of transient fluid-flow theory. All solutions of transient fluid-flow problems contain a parameter called the total system isothermal compressibility. This property of fluids and porous rock is a measure of the change in volume of the fluid content of porous rock with a change in pressure, and it may vary considerably with pressure. Evaluation of total system isothermal compressibility is not difficult, but it is tedious and time-consuming. Often compressibilities are estimated roughly, or transient flow methods are neglected completely. The benefits of using accurate system compressibility in properly-executed build-up or drawdown analyses are: 1. Better planning of pressure build-ups may be achieved to avoid unnecessary loss of revenue due to excessively long shut-in periods, or to shut-in periods too short to yield useable data. 2. Better and more reliable estimates of static formation pressures for reserves estimates and rate performance estimates. 3. Reliable information for evaluation of well completion effectiveness, and planning and interpretation of well stimulation efforts. The purpose of this paper is to clarify the nature of the total system isothermal compressibility, and to present useful methods for estimation of compressibility, particularly for systems containing a gas phase. DEVELOPMENT Numerous publications have presented solutions to transient single-phase flow of slightly compressible fluids, stressing pressure build-up applications. In transient flow, a compressibility* term arises to permit volume content of fluids in porous rock to change as pressure changes. The basic nature of the compressibility term is usually taken for granted. Problems arise in practical applications of transient fluid theory because most published works consider only one flowing fluid—in an ideal porous system containing only one fluid. In 1956, Perrine2 presented an intuitive extension of single-phase flow pressure build-up methods to multiphase flow conditions. Later, Martin- established conditions under which Perrine's multiphase build-up method had a theoretical foundation. Perrine has shown that improper use of single-phase build-up analysis in certain multiphase flow situations can lead to gross errors in estimated static formation pressure, permeability and well condition. It is likely that, much pressure build-up data for oil wells should be analyzed on the basis of multiphase flow. For both single-phase and multiphase build-up analysis, the isothermal compressibility term in dimensionless time groups often should be interpreted as the total system compressibility. All real reservoirs contain one or more compressible fluid phases. In addition, rock compressibility can contribute in an important way to the total system compressibility. The proper total system compressibility expression may contain terms for compressibility of oil, gas, water, reservoir rock and terms for the change of solubility of gas in liquid phases.

Jan 1, 1965

To the American Institute of Mining Engineers: The committee appointed at the February meeting upon Railway Resistances would respectfully report: That one person has been constantly employed in calculating the results of the data taken prior to March 1st, 1876. Also to complete the data taken upon the Lake Shore and Michigan Southern Railway, a diagram was taken upon a through freight train from Cleveland to Chicago, and one from Chicago to Cleveland. So that now we have diagrams from Buffalo to Chicago and return, which, when fully worked up, will give results of the utmost importance in determining the cost of transportation of freight. These data will be of much importance in determining the proper methods of equating grades and curves, which is so essential in the location of new lines. The calculations show that instead of our attempting to formulate results from data obtained on one road, it will be best for the in¬terests of transportation to enlarge the scope of our inquiries, and to extend the experiments so as to include all of the more probable causes which affect the cost of transportation. Were the details of railway equipment constructed alike, much work, which is now necessary, would be saved. It is not uncommon to find upon the same road 10 to 30 different patterns of something in construction to subserve the same purpose, which more or less modifies the friction of the cars. Take the majority of our trunk lines, with this diversity of construction, together with the varying conditions of track and manner of operating, and it will be at once seen that the labor and time to do the work and arrive at correct conclusions will occupy from two to three years. The results already attained in the short time in which they have been carried on, wholly by private enterprise, simply show what may be expected when the aid necessary is given to render them of the highest value to the great industries of the country. That the information may be general and of the greatest importance to our railway interests, the committee deem it advisable to secure, so * The following report, made at the June meeting of the Institute, is inserted in this place as appropriately supplementing the original communication of Mr. Dudley.

Jan 1, 1876

By D. G. Russell

Two techniques have been developed with which the applicability of pressure build-up analyses can be extended to include pressure data which previously have been considered virtually unusable. One of the interpretation methods makes possible the analysis of pressure build-up performance during the wellbore fill-up or after production period which occurs soon after a well is closed in. The other technique is an extension of a method for analyzing pressure build-up performance during the late-time portion of the pressure build-up which occurs after boundary eflects first begin to alter the shape of a conventional pressure build-up curve. With both of these methods it is possible to obtain estitnates of the kh product, the skin factor and the reservoir pressure. In addition, with the late-time analysis technique it is possible to obtain an estimate of the contributory drainage volume of the well being tested. This means that in some cases a check on reservoir limit test and (or) material-balance calculations can now be obtained from pressure build-ups. Both methods are slightly more time-consuming than conventional pressure build-up analysis methods because trial-and-error plots of pressure data must be made. The late-time method for analysis of pressure build-ups is in principle applicable to the late-time portion of a two-rate flow test or a pressure drawdown test. The interpretation formulas and procedures for these types of tests are also outlined. In these cases, as with pressure build-ups, it is significant that an estimate of the contributory pore volume is also obtained. On the basis of limited experience with the new techniques, it appears that satisfactory estimates of the kh product, skin factor, reservoir pressure and, for late-time analysis, contributory drainage volume can be obtained. INTRODUCTION The analysis of bottom-hole pressure build-up behavior in closed-in wells has been a a subject of interest in petroleum engineering circles for many years. In fact, few other subjects have received as much attention as pressure buildup analysis methods have. The cause for this interest is essentially twofold in nature. First, the pressure behavior of a well can normally be measured with a reasonably high degree of accuracy so that good data for analysis can be obtained. Secondly, over a fairly wide range of operating conditions, valuable information as to the quality of the reservoir rock and completion efficiency of the well can be obtained at a nominal cost. In recent years, numerous papers have been prepared on the effects of various operating conditions and reservoir heterogeneities on pressure buildup behavior. Very little work has been done, however, on extension of pressure build-up analysis methods to those pressure data which are not amenable to analysis by the present methods. The theory upon which the analysis of shut-in bottom-hole pressure build-up data is based is derived from the solution of the radial flow equation for a slightly compressible fluid for constant-rate conditions. It requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed bottom-hole pressure vs log (t + ?t)/ ?t (where At is shut-in time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the formation permeability, the well damage or skin factor, and the reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. The successful application of this procedure depends on being able to recognize the straight-line section on the basic pressure build-up plot. The presently used pressure build-up interpretation theory also assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing-in to the formation. This adjustment period is commonly referred to as the "afterproduction" or "fill-up" portion of the pressure build-up. During the period that the well fill-up effect is most pronounced, the basic pressure build-up plot is nonlinear. At later shut-in times after the effects of a drainage boundary have been felt at the well, deviation from the straight-line behavior of the pressure build-up plot also results. In many cases either of these effects or a combination of both can make the straight-line portion on the pressure build-up plot difficult to recognize. Obviously, an extension of pressure build-up analysis methods to include the afterproduction period and the period in which boundary effects are being felt would be desirable and might render valuable pressure data which for years have been considered virtually unusable. The principal reference of note concerning pressure buildup analysis during the afterproduction period is a paper by Gladfelter, Tracy and Wilsey.1 In the approach of these authors it is necessary to measure the rate of influx into the well during the afterproduction period. This is done through sonic measurements or through measurement of tubing-head and casing-head pressures simultaneously with

Jan 1, 1967

By D. E. Swets, R. C. Frank

It is well known that hydrogen is introduced into iron or steel as a result of many chemical processes (acid pickling, electrolytic cleaning, plating, etc.). One of the reactions that has been of recent interest1 is the reaction between an iron surface and water vapor. It was shown a few years ago2-4 that hydrogen can be introduced into steel at an accelerated rate during abrasion as a result of this reaction. Grun-berg and Scott have also observed that water in mineral oil lubricants increases pitting failure in ball bearings5 and they have suggested that hydrogen from the water is the primary cause of this effect.' In this laboratory, the question was raised as to whether or not hydrogen is also introduced into the metal surface of a bearing as a result of the decomposition of the hydrocarbon lubricant itself, and an experiment was performed to try to find a satisfactory answer. All steel parts contain some residual hydrogen. Therefore, it appeared that the best way to carry out this experiment without the need for highly accurate quantitative analyses was to use deuterium as a tracer. The natural abundance of deuterium in H2 is only 0.015 pct. The tracer was obtained in the form of deuteroparaffin (CD,(CDJ, CD,) and 0.25 g were dissolved in 20 cc of mineral oil to form the lubricant to be used in the tests. The bearings used were New Departure Type QOLOO ball bearings with a ball diam of 0.187 in. Prior to adding the mineral oil-deuteroparaffin lubricant, the bearings were cleaned in warm trichloroethylene to remove the packing grease. After packing with the new deuterated lubricant, the bearings were operated in a bearing fatigue test machine under a radial load of 190 lb and a thrust load of 190 lb at a speed of 3800 rpm. The expected life under these conditions is about 500 hr. Two tests were made; one for a period of 27 hr and the other for a period of 102 hr. The bearings achieved a temperature of 120o F during the tests. When the tests were stopped the balls were mechanically removed from the bearings and were immediately placed in liquid nitrogen to reduce degassing until the analysis for deuterium could be made. Before analyzing, the balls were warmed to room temperature and scrubbed with several degreasing agents to remove all traces of the deuteroparaffin mixture. This cleaning procedure was shown to be satisfactory by running a control test in which one ball bearing was subjected to all parts of the test except running in the fatigue machine. The hydrogen and deuterium were removed from the balls using a hot extraction apparatus attached to a mass spectrometer. Four balls from each bearing were analyzed. Each one was analyzed separately by removing it from a cold storage volume of the hot extraction apparatus and transferring it to the oven tube with a magnet. As the gases were evolved they were analyzed with the mass spectrometer. Since the hydrogen and deuterium pass through steel in the atomic form and since there are many more hydrogen atoms than deuterium atoms in the sample, the probability of forming an HD molecule is greater than forming a D2 molecule. For this reason the evolution of HD and H was followed as each ball was placed in the oven. The results showed that as each ball from the test bearing was dropped into the oven, the mass spectrometer recording of the HD evolution increased by about ten divisions. When balls from the control test bearing were dropped into the oven, the increase was about one division or less. The hydrocarbon background in the mass spectrometer was also monitored to see if hydrocarbons or deuterocarbons were given off when the balls were dropped into the oven, but no change in the hydrocarbon peaks was observed. Since the balls contained a fair amount of residual hydrogen, isotope ratio measurements were made on the gas obtained from each ball. The D/H value found for those balls which had been operated in the fatigue testing machine was consistently about 0.3

Jan 1, 1962

By H. M. St. John

MAINTAINING a satisfactory structure in brass and bronze castings has always been a foundry problem of great practical importance. While metallurgists and scientific investigators have not entirely ignored this matter, it has received less of their attention than has been given to iron, steel and the wrought copper and aluminum alloys. Investigation in this field has probably been discouraged to some extent by the complicated nature of the alloys involved. Hundreds of alloys are in more or less common use, most of them containing copper, zinc, lead and tin in-widely varying proportions. They also contain appreciable percentages of iron and antimony as impurities, and often phosphorus, which has been added as a deoxidizer and fluidifier. Small amounts of sulfur are usually present. It is not uncommon to find nickel, sometimes in rather substantial quantities. Traces of other metals are frequently present. So complicated and variable a mixture obviously offers difficulties in. any investigation of the various factors that influence the structure and other properties of the casting.

Jan 1, 1930

By J. H. Klepinger, C. W. Goodale

I. Introduction....................567 II. Character oF the OrE................568 III. Old FluE System..................572 IV. Tests on Old FLUE System..............575 1. Aspiration Tests................. 575 2. Tests with Steel Settling Chamber........... 575 3. Test with Experimental Brick Flue........... 583 4. Testa on Blast Furnace Geses............. 591 V. Design of New FluE System.............. 597 VI. Main Dust Chamber................. 605 VII. Some DetailS of Construction ............. 609 VIII. THE Chimney.................... 616 IX. Operation of New FluE System............. 624 X. Temperatures and DraFTS............... 630 XI. Velocities and Volumes................ 632 XII. TeStS on the New FluE System............. 637 XIII. Conclusion..................... 643 I. Introduction. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and as this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 1, 1914

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By James F. Kemp

In earlier gears, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections and maps prepared forty or more years ago for the Second Geological Survey of P ennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.' So far as I can discover faults fail in the charts, except in one small case in the Henry colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barr, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a numbcr of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer's surveys, possess great scientific and practical interest, bearing as they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due. The illustrations are taken from all four of the main basins, but are chiefly from the portions nearest Wilkes-Barre. The first are in the

Jan 1, 1922

By A. J. Boyer, T. R. Meadowcroft

An experimental determination has been made of the efject of surface diffusion on the vapor pressure obtained in a Kwudsen cell. The results show that a knife-edge orifice in a molybdenum lid may give erroneous results for the vapor pressure of silver. when a correction suggested by winterbottom and Hirth is made, the results become meaningful. Experimental work with cylindrical orifices in molyhdenz~m lids and knife-edge orifices in ceramic lids shows that good vapor-pressure results may he obtained when the orifice is designed so that ejfusion is the only significant source of weight loss. THE Knudsen effusion cell technique has been used by many investigators to study relative and absolute vapor pressures over metals and alloys at elevated temperatures. As a result of this interest, some theoretical studies have been made of geometric factors affecting effusion from the orifice of a Knudsen cell. A review of these studies has been made by Margrave.1 Recently, Winterbottom and Hirth2 have suggested that a physical effect, that of condensation, surface diffusion, and re-evaporation, may seriously affect Knudsen cell measurements, especially when a knife-edge orifice is used. Inasmuch as many of the present vapor-pressure data have been obtained using knife-edge orifices. it was felt that an experimental evaluation of the effect of surface diffusion on Knudsen cell measurements would be of value both in the design of the cell orifice and in establishing realistic estimates of the limits of error for existing data. The experimental program was in two sections. Firstly, measurements of the vapor pressure of silver were made in cells with cylindrical and conical orifices in which the surface-diffusion contribution to the weight loss should be negligible. These results were correlated with existing data to give a reliable measure of the real vapor pressure of silver. Secondly, measurements made using knife-edge orifices were corrected using the surface-diffusion theory of Winterbottom and Hirth2 and were then compared to the real values. The experimental arrangement is shown in Fig. 1. The balance was an Ainsworth RV-AU-1 automatic recording microbalance capable of measuring weight changes of ±0.02 mg on a total load of up to 100 g. The temperature was measured by an optical pyrometer signted on the bottom of the suspended crucible. The temperature readings were calibrated in a separate experiment in which pyrometer measurements were made while at the same time thermocouple readings were taken of the temperature at the inside top and bottom of the crucible. The range of reproducibility with this technique was ±4°C. A constant voltage source maintained a temperature of ±2°C at 1200°C over 10 hr. Silver of 99.99 pct purity was used in nonporous alumina crucibles. Lids of molybdenum, tantalum, or magnesia were cemented to the crucible using a sodium silicate cement. Table I shows the characteristics of the lids used. The vapor pressure is obtained using the basic Knudsen formula:

Jan 1, 1965

By Paul Giesecke

SINCE most modem metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. PRINCIPLES OF SPECTROCHEMICAL ANALYSIS In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1944

By R. E. Ogilvie, J. I. Goldstein, R. E. Hanneman

The interdiffusion coefficients for the Fe-Ni system were determined as a function of composition in both the a and y phases at 1 atm pressure. The inter diffusion coefficients were also determined in the y phase at 40 kbar pressure. The concentration gradients were measured with an electron probe, and the diffusion coefficients were calculated by the Matano analysis. At 1 atm, Ey increases with nickel content up to 65 at. pct Ni. The relationship of Dy with temperature and nickel concentration, up to 50 at. pct Ni, is given by the equation DY-l atm = exp(.0519 CN~ +1.15) MANY of the transformations that occur in the solid state are diffusion-controlled, especially those involving precipitate growth in most metallurgical systems. Multicomponent diffusion is usually expressed in terms of a chemical or an inter diffusion The activation energy Q at 1 atm decreases from pure iron to 60 to 70 at. pct Ni and decreases from pztre nickel to 60 to 70 at. pct Ni. The Kirkendall marker movement indicates that DFe is greater than DNi zcp to about 60 at. pct Ni. Above 60 at. pct Ni, however, DNi becomes peater than DFe The inter diffusion coefficients were also compared with those calculated from self-diffusion data. A comparison between calculated and measured coefficients shows only rough agreement. The effect of 40 kbar pressure is to decrease DyPl atm by an order of magnitude. The activation volumes for high-pressure diffusion are in favorable agreement with theoretical models developed for self-diffusion. coefficient which determines the rate at which material is transferred from the matrix phase to the precipitate and hence determines the growth rate of the precipitate. Since the numerical values of the diffusion coefficients differ widely as a function of the metallic system, temperature, and pressure, the diffusion coefficients must be determined for each particular environmental condition. Of long-standing interest is the growth of the classic Widmanstatten pattern in metallic (Fe-Ni) meteorites. The growth rate of the pattern is controlled by the diffusion coefficients in the Fe-Ni system. Since these coefficients are essential to calculating the growth rate of the pattern, we found it necessary to determine the diffusion coefficients

Jan 1, 1965

By Om P. Garg

During the period between 1970 and 1974 the Iron Ore Company of Canada had embarked on a detailed program to evaluate all aspects of mine design work for its open pit mines around Schefferville, located both in Quebec and Labrador, Newfoundland, Canada. One of the main conclusions was that the majority of the slope angles for the ultimate pit walls could be steeped. During the period 1975 and 1976,five (5) open pit iron ore mines were redesigned using the steeper slope angles up to 55 degrees. Initially these pits were designed at slope angles varying between 37 degrees and 45 degrees due to the generally fractured and leached nature of rocks in the area. During the active mining phase between 1976 and 1979, the stability of the steeper ultimate pit walls was monitored. The mining of ore was successfully completed in 1978 and 1979 in three pits. This of course, resulted in a significant savings due to a reduction in the quantity of waste that had to be removed. The successful pit slope redesign project was a co-operative effort between the Federal Government, Universities and the Iron Ore Company of Canada.

Jan 1, 1983

By L. W. Legerwood

During the past three decades, the oil industry has expended increasing eflorts seeking improved drilling tools or systems to reduce drilling costs. The total cost of these efforts is unknown, but it certainly amounts 10 tens of millions of dollars. Most of the "new" system that past and present investigators have sought to develop actually are old public information. In seeking to implement new-systern concepts, investigators have tested the following: impact at frequencies ranging from 6 to 300 cycles per second; electrical, mechanical and hydraulic meam of actuating percussors; bit rotary speeds up to 2,000 rpm; electric and hydraulic bottom-hole means of rotating bits; bottom-hole machines with power outputs up to 400 hp; shock waves; explosives; high-velocity pellets; flame; arc; grinding wheels; abrasive jets; erosion by high-velocity gases; chemical attack; electric current; magnetic waves; retractable rock bits; reelable drill pipe; continuous coring with reverse circulation; and automation of drilling rigs. Table I shows how these investigations are grouped for discussion purposes in this paper. In spite of these efforts to discover new and improved systems, rotary drilling main;aim its economic leadership. Undoubtedly, rotary drilling costs will continue to be reduced by rigid application of the best available technology and by development of new rotary technology. In view of the extensive past development programs, however, significant long-range improvement appears to be a research, not a development problem. Research must postulate and prove theories and principles governing variour subsurface rock-failure processes pertinent to both rotary and new systems. Ah, research must produce physical and engineering data relative to these processes. When such information is available, earth boring will graduate from an art to a science. Major improvements in rotary drilling can then be expected, and the systematic evolution of an improved drilling method can be initiated—with a strong probability for success. Development of drilling methods other than rotary drilling has been one approach investigated by the industry as a means for reducing drilling costs. Major cost-reduction efforts, however, have been centered on engineering development work aimed at incremental improvements in rotary drilling. A relatively minor effort has been expended to establish basic physical principles and engineering data pertaining to the earth-boring process which can serve as a foundation for the development of cost-cutting drilling hardware. Current oil-industry economic trends have added impetus to the need for effective programs to reduce drilling costs. However, areas for expanded future efforts should be selected only after careful study of past investigations. It is the purpose of this paper to review past and Dresent industry efforts to develop new drilling tools or systems and to suggest areas where additional science is needed. Past reviews of drilling methods have been limited to a few processes prominent at the time the reviews were made. This paper seeks to present a concise, well organized review of all methods that have received actual development or test work. The preparation of a paper seeking to review all past developments is fraught with many difficulties, not the least of which are errors in or obsolesence of printed matter used as source material and the lack of data on industry developments which have not been published. Since de-

By E. M. Wise

IN a previous communications the improvement in strength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are pre-sented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for deter-mining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a, novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum.

Jan 1, 1933

September 1 to 6, 1918 COMMITTEE IN CHARGE Spencer Penrose, Chairman. George M. Taylor, Vice-Chairman. A. E. Carlton, Chairman. Finance Committee J. Dawson Hawkins, Secretary DENVER COLORADO SPRINGS CRIPPLE CREEK Finance Finance Thomas B. Crowe T. B. Stearns A. E. Canton , E. P. Arthur, Jr. Richard A. Parker Spencer Penrose N. S. Greensfelder T. B. Burbridge George M. Taylor A. E. Carlton. A. L. Blomfield, Treasurer B. F. Hill Arrangement I F. G. Willis Dave G. Miller Registration Norris E. Eads Frank Bulkley Loren C. Lennox 1V. E. Ryan Geo. E. Collins Horace F. Lunt Fred Jones .1. M. Tippett F. D. Smale Entertainment J. H. Haynes F. H. Bostwick Arrangement and Entertainment L. W. Lennox F. E. Shepard George M. Taylor A. L. Blomfield M. R.. Valentine Howland Bancroft J. D. Hawkins Thomas B. Crowe B. P. Morse A. E. Carlton E. P. Arthur J. G. Perry G. H. Clevenger Etienne A. Ritter Ladies Ladies , PUEBLO Mrs. T. B. Stearns, Mrs. C. M. Taylor, Mrs. C. H. Clevenger J. F. Welborn Chairman. Chairman H. B. Carpenter Mrs. C. Loughridge Mrs. S.-Penrose Mrs. A. E. Carlton L. B. Eames Mrs. H. Bancroft Mrs. J. D. Hawkins Mrs. A. L. Blomfield F. Robinson Mrs. G. Bancroft Mrs. L. C. Lennox Mrs. J. M. Tippett . Mrs. W. D. Leonard Mrs. H. F. Lunt -Mrs. E. C. van Diest Mrs. C. Chase Mrs. E. A. Ritter Mrs. AV. Strieby Mrs. F. H. Bostwick Mrs. L. S. Harner Mrs. C. L. Bailey Mrs. F. Bulkley Miss F. Dickerman Mrs. E. P. Shove Mrs. C. L. Tutt Mrs. F. C. Peck Mrs. F. D. Pastorius

Jan 10, 1918

By Fred C. Bond

THEM is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determinations of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

By Roland D. Parks

Corundum, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to Our allies. Optical elements Of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some Of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any Of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mobs' scale index of 9, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent Of this paper to deal Only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. Ore Production and Consumption For the past two decades, south Africa has been the world's sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world's principal consumer of corundum ore; imports lor the period 1934 through 1940 averaging 3000 Short tons per year, The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 Short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the united States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918 Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912

Jan 1, 1948

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

By R. J. Wasilewski

THERMAL expansion of rhenium data have been reported by Agte et al.,&apos; and Medoff and cadoff,&apos; respectively, while the linear expansion coefficient was determined by Sims et Al.3 Denoting expansion coefficients parallel and at right angle to c axis by all and Al respectively, their weighted mean should be equal to dilatometric linear coefficient of a random polycrystalline specimen. The values reported for these coefficients are tabulated below: Since these values are in poor agreement, and because of anomalous expansion behavior observed in titanium 4 and chromium, a rede termination of the axial expansion was carried out. A Unicam 19-cm-diam high-temperature camera was used, with unfiltered CuK radiation. Camera calibration was carried out using at Pt wire standarde at temperatures up to 1100oC, the variation between indicated and true temperature being within the experimental error (estimated at <3oC) above 750o C. Rhenium Johnson Matthey spectrographic standard) was vacuum annealed at 1000 oC prior to X-ray diffraction experiments. Lattice parameters were obtained by least-squares solution using the reflec- tions (1232), (1015), (2024), and (3030) for all the patterns, and the additional reflection (2133) for higher temperature (400°C and above) patterns. The relative expansion data obtained are shown in Fig. 1, lengths of the vertical bars indicating the spread in the parameter values obtained by using various combinations of three spacings from the four or five measured. The data calculated from the equation of Ref. 2 are included for comparison purposes. Several specimens were used to obtain the above data, neither of them showing a significant parameter change after completion of the high temperature runs. Some parameter data and the corresponding expansion coefficients between 25 oC and the measurement temperature are tabulated below. The comparison of the present data with those previously reported shows reasonable agreement with the results of Medoff and cadoff2 within the temperature range covered by them (up to 1000 oC). The a values are appreciably higher throughout most of the investigated temperature range. The basal expansion is—in agreement with their findings—appreciably higher than that in the direction of hexagonal axis. The expansion coefficient, al, however, decreases rather more slowly with temperature than previously reported. The expansion along the c axis up to nearly 1000°C appears in excellent agreement. However, at higher temperatures there is a marked deviation towards higher expansion, reproducible between different specimens. Furthermore, there seems to be some irregularity in the variation of all with temperature, the apparent local minimum and maximum values at 510o and 1024o C, Table II, being well outside the experimental error limits. It must be stressed that the apparent discontinuity in the c parameter expansion is still insufficient to account for the expansion value reported by Agte et al.&apos; since a total expansion of close to 2 pct would

Jan 1, 1962