Search Documents

By H. Scott

IN a paper read before the Institute of Metals, Rosenhain 1 described a new type of furnace designed primarily for the thermal analysis of metals by the inverse-rate method and used by him in the metallurgical department of the National Physical Laboratory with considerable success. In his discussion of this furnace, Rosenhain pointed out some difficulties met with in its operation, such as uniformity of rate of heating or cooling being inadequate for the degree of accuracy aimed at. To overcome this difficulty, he suggested, in place of motor propulsion, a gravity drive controlled by a"hydraulic cylinder with a relief valve whose width of opening can he regulated to allow of any desired rate of motion." The authors, in constructing a thermal-analysis furnace of Rosenhain's type, have therefore followed this suggestion and also added certain features that increase somewhat the convenience and simplicity of its operation. Requests for information regarding this furnace and the highly satisfactory results obtained from its use, it is believed, justify describing its construction and operation in sufficient detail to make possible its duplication or improvement. Description of Furnace.-The details of the furnace construction are shown in Fig. 1, which is drawn to scale. The heating tube is of /4 in. (6.35 mm.) wall "alundum" heated at the upper end by seventeen turns of 0.52 mm. platinum wire, which is coated with "alundum" cement supplied for this purpose. The cement coating is essential when a high temperature (over 1000° C.) is required, as it prevents hot spots with the resulting burning out of the heater. This platinum-wire winding, unlike "nichrome," is entirely satisfactory for temperatures of at least 1000° C. It has been maintained at that temperature continuously for 2 months and shows no signs of deterioration. This temperature is maintained by a current of 5 amp. drawn from 30 volts potential, so its necessarily continuous operation is quite economical.

Jan 8, 1919

By J. F. Wilkinson

A high degree of accuracy is often required in mine-surveying, in order that expensive mining work may not be misdirected. The making of underground connections by drifts or shafts located as the result of surveys presents a crucial test of correctness not usually involved in any other class of surveying. In view of these considerations, the present notes and description of a survey made in June, 1890, for the San Francisco shaft of the New Almaden quicksilver-mines, may be of interest to members of the Institute who are surveyors. The purpose of this survey was to locate on the surface a vertical 2-compartment shaft (3.5 by 7 ft.), to connect with another vertical shaft, of practically the same size, which had been sunk a number of years before from an adit-level about 240 ft. vertically below the surface, to a deeper, so-called 600-ft. level. It will be seen, of course, that the most important matter was to secure an exact coincidence in vertical line, so that the resulting continuous vertical shaft from the surface should have no offset or irregularity at the point of junction between its two parts. The levels were of less importance; but, as the hoisting-works were to be placed in position and the new shaft permanently timbered from the start, its correct alignment was an essential requirement. The important features of the work, therefore, were the methods used in determining with certainty : 1. That the shaft was located in the right place in a general way; 2. That the ordinary inaccuracies of linear and angular measurements were so reduced as to insure correctness of location within certain defined and allowable limits. Instruments.—Thc instruments used were: a Buff and Berger transit-theodolite, with a 6-in. horizontal plate, reading to 10 seconds; a Heller and Brightly Y-level; a Chestermán steel tape, graduated in tenths and hundredths of a foot; and New York leveling-rods, graduated to thousandths of a foot.

Jan 1, 1901

L. S. Austin, Denver, Colo. (communication to the Secretary) : Mr Hartman says (p. 4 of the pamphlet) that the penetration of air into the crucible of the blast-furnace " is, of course, a function of the diameter of the nozzle." To this I would emphatically take exception. Fig. 1 represents a vertical ideal section of tuyere, cruciblewalls and charge, immediately at the tuyere, in which the currents of air are represented, both in quantity and in direction, by the tortuous black-lines emanating from the nozzle-opening and passing through channels of the least resistance. As an electric current, flowing by various conductors to a common point, is carried in quantity inversely as the resistance of those conductors, so here the air ramifies through the most open cavities or channels, relatively little of it passing where the resistance due to fine materials is great. This figure represents the course of currents in the vertical plane only. As a matter of fact, they pass away in every plane, as opportunity offers. The effect of blocking or decreasing the area of the nozzleopening would certainly only decrease the quantity of air entering by that particular tuyere, without assisting penetration. The large channels (b, b, Fig. 1, for example) would still carry the larger part of the air, while again the smaller channels (a, a, a) would continue small and take no larger percentage of the air than before. These channels momentarily change, however, with the slow descent of the coke. Further on (p. 5), Mr. Hartman describes the dispersive effect of a single lump of fuel. He has only to conceive the entire spaces before the tuyere-nozzles as filled with such lumps, in order to parallel the condition of affairs I have just explained. It is where the large pieces of the charge come down, that the mass is the most open, and the blast passes most freely. On the other hand, wherever the fine ore collects combustion proceeds slowly, because of the smaller supply of air. The

Jan 1, 1899

By J. B. Austin

IT is now well established, chiefly through the work of Davenport and Bain,1 that the influence of temperature upon the rate of transformation of austenite to ferrite at constant temperature is represented by a curve of the type shown in Fig. 5 of Tech. Pub. 589; and the reasons for this general shape have been discussed by them in a qualitative way. Thus, the upper part, or nose, of the curve is the resultant of two factors of which the rate of change with temperature is not the same, and by analogy with other like cases it is almost certain that these factors are: (1) the chemical potential, or driving force, of the transformation, which is zero at the equilibrium temperature and increases rapidly as the temperature falls below this point; and (2) a factor analogous to viscosity, or resistance of the crystal lattice to a change in structure, which also increases as the temperature is lowered. Just below the equilibrium temperature this virtual "viscosity" of the metal is relatively low-that is, the metal offers little resistance to a change in lattice-but the driving force is also small, and the net result is that the reaction proceeds slowly. As the temperature is lowered the magnitude of both factors increases; but at first the driving force increases more rapidly than the resistance and the reaction is observed to proceed more rapidly. At lower temperatures, however, the resistance begins to increase faster than the driving force, and eventually, at the nose of the curve, overbalances it, causing the reaction to proceed more and more slowly thereafter. This concept is somewhat, though not completely, analogous to that employed in certain electrical cases where the precise factors are known and are separately measurable. The current I (in amperes or coulombs per second) flowing through a given wire is proportional to the impressed potential, or driving force E, and is inversely proportional to the resistance R of the wire; that is, I = E/R. Stated in a slightly different way,

Jan 1, 1935

By Milton Williams

IT is generally recognized that fluid is lost from rotary drilling mud s to permeable strata during normal drilling operations;1,2,3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 . The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable ent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the "tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata.

Jan 1, 1939

By G. S. Brooks, L. G. Duncan

During the past few years, the Mineral Point Zinc Co. has had under consideration the improvement of various types of gas-filtering apparatus used in the removal of dust from crushing and milling plants, in the manufacture of oxide, and on blast-furnace fume and sintering furnaces. The original equipment of the various plants of the company was, of course, along lines of the standard stationary bag house. These houses required large surfaces, hand shaking, and varied only in the manner of the collection of solids and in the distribution of the gas. , Early in 1908, the first trial of a mechanical bag house was made at Nassau Plant at Depue, Ill. The duty of this installation was on dust-laden gas from a fine-crushing mill. The Printz and Rau bag machine was finally adopted and put into operation. This ingenious machine embodied what were then to us two novel features in bag-house practice: 1. An intermittent crinkling and snapping of the filtering fabric to free the meshes of solids. 2. A reversal of gas flow for a short period by a temporary connection with the suction trunk. This equipment worked fairly well except in cold weather, when we ran into condensation troubles. Had we at that time understood more fully some of the limitations of fabric filtering work, these might well have been remedied. We were impressed by this experience, however, with the efficiency of sudden tension on the fabric under suction. After a study had been made of some of the western blast-furnace houses using the reversal-of-flow feature, experiments were started early in 3 914 with a view to developing an automatic equipment along the best lines of our past experience. The objects sought were: 1. Keeping labor out of the houses for hygienic reasons. 2. Reduction of labor costs. 3. Reduction in size of bag houses. 4. Accessibility. 5. Ability to handle relatively hot gases where required.

Jan 1, 1918

By Warren L. Howes

THIS paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. FLOWSHEET The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybdenum-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day. [t] Fig. I shows an abbreviated flowsheet of the grinding section of the mill. PRIMARY BALL MILL A 3-ft. Symons shorthead crusher in open circuit crushed to ¼ -in. maximum one-way dimension the feed to the 5 by 10-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. [ ] In order to clarify the difference in design of the various types of liners used, Fig. 2 shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I.

Jan 1, 1943

CONTENTS PAGE FULTON, CHARLES H., and READ, J. BURNS-A New Roasting Furnace for Zinc Flotation Concentrate. Discussed by Charles H. Fulton, Arthur S. Dwight, B. M. O'Harra, Kurt Stock 1 STOCK, KURT.-Redistillation of Zinc. Discussed by G. E. Dalbey, Kurt Stock.. 3 BEASLEY, F. E.-High Zinc in Lead Blast-furnace Slags. Discussed by R. C. Canby, R. L. Lloyd, C. R. Haywood, G. E. Dalbey, A. S. Dwight, E. P. Mathewson, A. L. Walker, B. M. O'Harra, and C. P. Linville 4 STEELE, E. W.-Application of Pulverized Coal to Copper Refinery Furnaces. Discussed by F. R. Pyne, E. P. Mathewson 11 LINVILLE, C. P.-Recovery of Arsenic and Other Valuable Constituents from Speiss. Discussed by C. R. Hayward, C. P. Linville, G. E. Dalbey, A. S. Dwight, Edward F. Kern, Karl Eilers, E. P. Mathewson 12 A New Roasting Furnace for Zinc Flotation Concentrate Discussion of the paper of CHARLES H. FULTON and J. BURNS READ, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1362-D, with MINING AND METALLURGY,. October, 1924. G. E. DALBEY, East Berlin, Conn. What would be the, effect on the formation of sulfates of an increased water vapor content in the roasting gases? CHARLES H. FULTON.-I cannot answer that from our experience. The question of the formation of sulfate in the roasting of zinc is mainly one of temperature and the concentration of S02 and S03 in the gases. We found we could roast almost completely to sulfate if the concentration was kept at the proper point. We, however, did not care to do this because we wished to make a 5 to 6 per cent. S02 gas for sulfuric-acid work. The sulfating of the zinc oxide in the proper concentration of gases goes on very rapidly. There are certain places in the furnace system such as the Cottrell and in a part of the dust chamber in which the roasted

Jan 6, 1925

By Guy W. Crane

The geology of the Tintie mining district, fully treated, would occupy an elaborate monograph. This less comprehensive paper is devoted primarily to the occurrence and origin of the orebodies of the district, while space is given to those phases of the general geology only which seem necessary to a proper setting of such a discussion. The first geological report on the Tintic district to be issued was that by Tower and Smith, published in 1899, in the form of a paper in Part III of the Nineteenth Annual Report of the U. S. Geological Survey, and also as Folio No. 65, Geologic Atlas of the United States. About four years ago a second investigation was begun by Waldemar Lindgren and G. F. Loughlin, of the U. S. Geological Survey. With the exception of a paper on the oxidized zinc ores of the Tintic district by Mr. Loughlin, the results of their work are still unpublished. The writer's acquaintance with the district began in the fall of 1913, and has extended over a period of about two years. 1. Location The Tintic district lies about 65 miles due south of Salt Lake City, and on the west central slope of the Tintic Mountains, a short range, which forms the connecting link between the Oquirrh Mountains on the north and the Canyon Range on the south—the group constituting the first of the Basin ranges to the west of the Wasatch Mountains. The productive portion of the district embraces an area about 6 miles long and 2 miles wide, which is divided between Juab and Utah Counties. Within this area are the towns of Eureka, Mammoth, Robinson, Silver City, and Knightsville. All these points are tapped by the Denver & Rio Grande and S. P., L. A. & S. L. Railways. 2. Topography As in most of the Basin ranges, topographic relief is strong, dropping rapidly from peaks of 8,100 ft. above sea level to elevations of 5,600 ft. in Tintic Valley on the west and 4,500 ft. in Goshen Valley on the east.

Jan 1, 1916

By Nico Van Wingen

Experiments performed with distilled water, unconsolidated sand and dead oil for the purpose of determining the influence of oil flow on the water content of sands were described. While results found are not necessarily, therefore, identical with those that would be obtained under natural petroleum reservoir conditions, the following conclusions were drawn. 1. When oil under constant head is flowed through an unconsolidated sand, the amount of water retained in the core is inversely proportional to the specific permeability of the core. This corroborates the view that the degree to which oil displaces water out of the pore space is limited by the size of the pores. 2. For the range investigated, the displacing action of a more viscous oil of higher specific gravity was found to be the same as a less viscous oil, or lower specific gravity. 3. The amount of interstitial water retained in the sand bears an inverse relationship to the pressure head of the displacing liquid. 4. The degree of retained water saturation of the sand appears to approach 100 per cent as the specific permeability approaches zero. 5. For the higher values of specific permeability and for the pressure range investigated the remaining amount of water in the sand occupies approximately 10 per cent of the pore space. This, together with the fact that the limiting oil velocity curve approaches approximately 10 per cent water saturation as an asymptote, indicates that beyond this point removal of water is achieved only by a stripping of the grains requiring considerable pressure drops across the sands; or by a balancing of the molecular forces. 6. As the water saturation of the sand exceeds approximately 15 per cent of the pore volume, the permeability of the sand to oil decreases rapidly. 7. Sands with water saturations as high as 40 per cent were found to produce 100 per cent oil.

Jan 1, 1939

By T. J. Woodside

A. E. LEE*—One question of the flue leading to the tube coolers. What gas velocity is maintained to prevent settling of the finely divided fume ? T. J. WOODSIDE (author's reply)— 30 fps. Of course some fume settles out, but is immediately carried away by the screw conveyors. H. R. BIANCO —How effective are the soot blowers ? Do you have to use any hand lancing? T. J. WOODSIDE Only one point, which is right at the top of the economizer and which the soot blowers do not reach, we occasionally hand lance. But everywhere else the soot blowers have been very effective and no hand lancing has been done. L. V. DAVIDSON*—Do you have considerable variation in the lead content of the fume collected if the lead is higher, and is there greater tendency for the fume to stick on the boiler tubes ? T. J. WOODSIDE—There is very little variation in the lead content. From 5 to 7 pct is the widest range variation we have had and we have noticed no difference in the behavior of the fume. C. R. KUZELL—Mr. Woodside has been quite generous with data pertaining to metal and fuel economics. I think he stated that the coal consumption of the furnace was 21/10 21/10 for a pound of zinc recovered. I take it that that is the gross coal input to the furnace. I wonder what the net fuel consumption in terms of coal might be after crediting the fuel equivalent of the waste heat steam recovered? T. J. WOODSIDE—The fuel value of the waste heat steam is approximately 42 pct of the heat input to the furnace. A very large part of the heat, of course, goes out in jacket water—44 pct. A. D. TERRELL*—I would like to know how much lead is in the deleaded material. T. J. WOODSIDE—It is a little less than 2 pct now.

Jan 1, 1950

By Nico Van Wingen

Experiments performed with distilled water, unconsolidated sand and dead oil for the purpose of determining the influence of oil flow on the water content of sands were described. While results found are not necessarily, therefore, identical with those that would be obtained under natural petroleum reservoir conditions, the following conclusions were drawn. 1. When oil under constant head is flowed through an unconsolidated sand, the amount of water retained in the core is inversely proportional to the specific permeability of the core. This corroborates the view that the degree to which oil displaces water out of the pore space is limited by the size of the pores. 2. For the range investigated, the displacing action of a more viscous oil of higher specific gravity was found to be the same as a less viscous oil, or lower specific gravity. 3. The amount of interstitial water retained in the sand bears an inverse relationship to the pressure head of the displacing liquid. 4. The degree of retained water saturation of the sand appears to approach 100 per cent as the specific permeability approaches zero. 5. For the higher values of specific permeability and for the pressure range investigated the remaining amount of water in the sand occupies approximately 10 per cent of the pore space. This, together with the fact that the limiting oil velocity curve approaches approximately 10 per cent water saturation as an asymptote, indicates that beyond this point removal of water is achieved only by a stripping of the grains requiring considerable pressure drops across the sands; or by a balancing of the molecular forces. 6. As the water saturation of the sand exceeds approximately 15 per cent of the pore volume, the permeability of the sand to oil decreases rapidly. 7. Sands with water saturations as high as 40 per cent were found to produce 100 per cent oil.

Jan 1, 1939

By Arthur C. Simmons

Oil production and activity in northern and central Pennsylvania was slightly less in 1939 than in the previous year, but owing to higher average prices 1939 was undoubtedly a better business year. The last quarter showed markedly increased activities throughout all of the Pennsylvania fields. Production, Stocks and Price Storage of Pennsylvania crude oil at pipe lines and refineries totaled 5,413,000 bbl. on Dec. 31, 1938, and declined during the year 1,124,000 bbl. to a total of 4,319,000 bbl. at the end of 1939. The stocks of crude at the end of the year represent the lowest point reached in Pennsylvania-grade crude storage in recent years. Stocks increased slightly during April, May and June, but decreased during all other months of 1939. The Bradford field production within the state of Pennsylvania averaged 35,340 bbl. per day throughout 1939, which represents a decrease of 1419 bbl. a day from the 1938 average. The production in central and southern Pennsylvania increased 1176 bbl. per day, averaging 12,159 bbl. throughout 1939. Table 1 includes annual production for the part of Bradford field situated within the state of Pennsylvania, for central and southern Pennsylvania, and for the entire state of Pennsylvania. A definite segregation of production between the Bradford field and central and southern Pennsylvania is slightly ambiguous because a portion of the oil from the newly discovered Music Mountain pool is included statistically in each area. In all probability the entire increase and some small addition to the production from southern Pennsylvania can be attributed to oil produced from the Music Mountain pool. Within the Bradford field, six price changes occurred throughout the year. At the beginning of 1939 the price of Bradford crude oil was $1.80 per barrel, whereas by the end of the year it had risen to $2.50. The weighted average price for Bradford crude during 1939 was $2.059 per barrel.

Jan 1, 1940

By E. A. Stephenson

In spite of tremendous handicaps notable advances in production engineering have been achieved during 1932. The technique of deep well drilling has continued to progress, notably in California and at Big Lake, Texas. In the latter field a method has been devised by which two grades of oil in contact with each other are produced without intermingling. In rig design many improvements have been made whose objective is to facilitate deep drilling with reduced power losses and increased life of the equipment. Flush joint casing and drill pipe have been improved further, careful tests indicating that the drilling time can be reduced by from 5 to 20 per cent where flush-joint pipe is used. Slow-speed pumping has come into wider use, with further increases in over-all efficiencies. A number of improved well pumps also have been developed and are being tested. One of the most important of these is a positive displacement pump of the rotary type, directly connected to an electric motor placed in the bottom of the hole, and adaptable to various sizes of tubing and casing. In some localities the trend is towards the replacement of electric motors and large-cylinder engines by multiple-cylinder gas engines. Experiments have been conducted and critical analyses made of flow conditions in wells equipped with various styles of tubing which give promise that tubing may be designed to fit individual well conditions. In those wells producing at less than maximum capacity, the gas-oil ratio has been shown to depend on the rate rather than on the method of production, or the design of equipment. Important factors in the design of screened pipe have been carefully analyzed and made the basis of a method for determining the required mesh. Remarkable progress has been made in the use of subsurface pressure data. In East Texas particularly, use of such data is providing a means for the control and equalization of water encroachment and is also pointing the way to a sound means of allocating to individual tracts an

Jan 1, 1933

By C. G. Dunn, F. Lionetti

W. G. BURGERS*—It seems almost certain that this investigation shows the way which finally, when more analogous data have been obtained, must lead to the understanding of many features of preferential growth-directions of crystals and of the occurrence of recrystallization textures. In this connection I should like to mention that Mr. Tiedema in my laboratory succeeded in developing an analogous method for preparing crystals in aluminum plates with a chosen crystal-lographic plane and direction parallel to the surface of the plate (to be published in Cryst. Ada). If such crystals were grown in high purity aluminum and test-pieces containing a few crystals such as the authors describe were prepared for this metal, it might be possible that due to the absence of growth obstructing particles, even in this low-melting point metal boundary displacements approaching equilibrium positions might be realized. With regard to the apparently marked drop in surface energy for orientation differences approaching zero degree, and orientation differences approaching those existing between twins, it seems of interest to remark that in aluminum a crystal growing at the expense of fine grained material cannot (or can only very reluctantly) absorb grains in either ap- proximately (within 5—10°) parallel or spinel twin orientation (May, Tiedema and Burgers, Nature (1948) 162, 740 and Cryst. Ada in press). Consequently with aluminum the method of preparing a crystal with a definite orientation does not succeed when the new crystal has to absorb its own texture; for example it is not possible to grow in a polycrystalline wire with a [lll]-texture a crystal with a [11 Indirection parallel to the wire axis (Tiedema: Cryst. Ada, in press). Finally I should like to mention the well-known fact (Burgers: Proc. Acad. Amsterdam (1947) 50, 723) that prolonged annealing of recrystallized nickel-iron sheet with cube-texture never succeeds in transforming this into one single crystal of the same orientation; if, by "secondary re-crystallization," large crystals are formed

Jan 1, 1950

By Arthur C. Simmons

Oil production and activity in northern and central Pennsylvania was slightly less in 1939 than in the previous year, but owing to higher average prices 1939 was undoubtedly a better business year. The last quarter showed markedly increased activities throughout all of the Pennsylvania fields. Production, Stocks and Price Storage of Pennsylvania crude oil at pipe lines and refineries totaled 5,413,000 bbl. on Dec. 31, 1938, and declined during the year 1,124,000 bbl. to a total of 4,319,000 bbl. at the end of 1939. The stocks of crude at the end of the year represent the lowest point reached in Pennsylvania-grade crude storage in recent years. Stocks increased slightly during April, May and June, but decreased during all other months of 1939. The Bradford field production within the state of Pennsylvania averaged 35,340 bbl. per day throughout 1939, which represents a decrease of 1419 bbl. a day from the 1938 average. The production in central and southern Pennsylvania increased 1176 bbl. per day, averaging 12,159 bbl. throughout 1939. Table 1 includes annual production for the part of Bradford field situated within the state of Pennsylvania, for central and southern Pennsylvania, and for the entire state of Pennsylvania. A definite segregation of production between the Bradford field and central and southern Pennsylvania is slightly ambiguous because a portion of the oil from the newly discovered Music Mountain pool is included statistically in each area. In all probability the entire increase and some small addition to the production from southern Pennsylvania can be attributed to oil produced from the Music Mountain pool. Within the Bradford field, six price changes occurred throughout the year. At the beginning of 1939 the price of Bradford crude oil was $1.80 per barrel, whereas by the end of the year it had risen to $2.50. The weighted average price for Bradford crude during 1939 was $2.059 per barrel.

Jan 1, 1940

By William P. Blake

In my short " Contribution to the Early History of the Industry of Phosphate of Lime in the United States,"* mention is made of the erection by Dr. Emmons and myself of a magnetic machine for the removal of iron-ore from the so-called "red sand," a granular form of apatite. At the time of writing, it was not possible to refer to my diary and notes, and the general statements were made from recollection. The subject seems to have special interest at this time, by reason of the many forms of machines now being introduced and patented for similar purposes; and, having received letters of in quiry for further details, I have availed myself of the opportunity, when recently at home for a few days, to refer to the original notes and records made by me in 1852, when living at Crown Point and Moriah, on Lake Champlain. The machine mentioned in my former communication mas pur chased of Ransom Cook, of Vermont. It arrived, and was un loaded from the boat and taken part way up to the nine, on October 18,1852. The weight was 1400 pounds and the cost $1200. It was constructed, not with permanent magnets but with electro-mag nets. It was set up and first turned by hand on October 28th, using twelve battery-cups or cells, the connections being made with wires in small cups of quicksilver. The magnets were not sufficiently strong, and the machine did not work well. More batteries were sent for, arid the machine was started with steam-power on Novem ber 6th. The ore was dried in kilns, then put through a coffee-mill crusher or grinder, and then fed upon the leather belt which carried it under the magnets. Many experimental runs were made, and some diffi culties were overcome, before December 21st, when the record states that the machine was working pretty well, using 24 cells and giving a product of from 3 to 5 tons a day of granular phosphate. The ori-

Jan 1, 1893

By J. Stubbins

1 1.4-1. Source of Water. Precipitation in the form of rain or snow is the original source of water that enters most surface mines. The precipitation, which does not escape to the atmosphere, either becomes surface run- off or infiltrates into the ground to become ground water (3,4). Evaporation and surface run-off can be measured. The water that infiltrates the ground disappears from view and is more difficult to evaluate. In general, it moves in a pattern similar to the surface run-off, but at a much slower rate, since its progress is impeded by many subsurface conditions. The infiltrating water descends through the soil and rock by whatever passageways permit flow until the water table or top of the zone of saturation is reached. Though usually pictured as a level surface, it is dependent upon the topography and the permeability of the enclosing material, and therefore it can be as erratic and unpredictable as the subsurface geology. Ground water may become surface run-off again at a lower point, and likewise, surface run-off of lakes and streams can infiltrate to become ground water. Should the ground water be confined to a permeable zone overlain by an impermeable barrier, a pressure is created. Such water is said to be artesian if the pressure head is sufficient to raise the confined water to the surface. These conditions are more commonly found in relatively flat-lying bedded formations. 11.4-2. Recognition and Estimation of Water. Dewatering and flood control should be considered by the design engineer at an early stage in all surface mine planning. Recognition of the possible problems, and making allowance for their solution, is an inexpensive precaution. Circumstances which should lead to investigation are: 1. High rainfall 2. Experience of other mines in the area 3. Evidence of water and caving in drill holes 4. Presence of springs and artesian wells 5. Geological evidence of aquifers.

Jan 1, 1968

By Norman F. Patton

The subject assigned is so broad that thorough discussion is well-nigh impossible within the space allotted, and further, few specific data are available upon which to predicate conclusions concerning the efficiency of present methods of distributing anthracite. This paper treats briefly the various agencies through which both primary and secondary distribution are effected, the methods of transportation and the general interrelation of production, demand, inventories and price. Avenues of Distribution Three distinct types of primary distribution are common in the marketing of anthracite. First, though not most important, is the sale by the producer, or operator, direct to the consumer. These sales, other than to employees and the local trade, are generally confined to steam sizes for industrial uses, and are consigned to the sidings or docks of the consumer. Sales of this type often are so closely priced to compete with oil and bituminous that the addition of even a small dealer's margin is sufficient to increase the cost to the point where the business might be lost. Second, the operator sells to a wholesaler or broker for subsequent resale, either to a retail dealer for clearance through his yard or direct to large consumers. Usually this method of distribution is employed by the smaller operators, who do not find it economically feasible to maintain extensive sales organizations. In most instances, the wholesaler retains some 5 per cent for his services, paid, of course, by the producing company whose anthracite he handles. He may, and frequently does, handle the output of several different companies, suited to the varying needs of the different communities he serves. His business includes all sizes of anthracite. The third, and by far the most general method, consists in selling to retail dealers, shipments being made direct from the breakers to the yards of the dealers. In large consuming areas, such as the metropolitan districts of New York or Philadelphia, one operator may sell to several

Jan 1, 1936

By Norman F. Patton

The subject assigned is so broad that thorough discussion is well-nigh impossible within the space allotted, and further, few specific data are available upon which to predicate conclusions concerning the efficiency of present methods of distributing anthracite. This paper treats briefly the various agencies through which both primary and secondary distribution are effected, the methods of transportation and the general interrelation of production, demand, inventories and price. Avenues of Distribution Three distinct types of primary distribution are common in the marketing of anthracite. First, though not most important, is the sale by the producer, or operator, direct to the consumer. These sales, other than to employees and the local trade, are generally confined to steam sizes for industrial uses, and are consigned to the sidings or docks of the consumer. Sales of this type often are so closely priced to compete with oil and bituminous that the addition of even a small dealer's margin is sufficient to increase the cost to the point where the business might be lost. Second, the operator sells to a wholesaler or broker for subsequent resale, either to a retail dealer for clearance through his yard or direct to large consumers. Usually this method of distribution is employed by the smaller operators, who do not find it economically feasible to maintain extensive sales organizations. In most instances, the wholesaler retains some 5 per cent for his services, paid, of course, by the producing company whose anthracite he handles. He may, and frequently does, handle the output of several different companies, suited to the varying needs of the different communities he serves. His business includes all sizes of anthracite. The third, and by far the most general method, consists in selling to retail dealers, shipments being made direct from the breakers to the yards of the dealers. In large consuming areas, such as the metropolitan districts of New York or Philadelphia, one operator may sell to several

Jan 1, 1936