Search Documents

By Walter Weeks

CONSIDERABLE difference of opinion seems to exist as to whether the rate of air flow when a fan is placed on a given duct should be determined by the use of static pressure or total pressure characteristics. A little study will show that both methods are correct. Assume that a fan is connected to a duct by an expansion piece as shown in Fig. 1, and that steady flow is established. Considering the atmospheric pressure as zero pressure, let the static head at the outlet of the fan be h and the velocity at this point be v1. The total head at the outlet is then h + v1/2g? The total head at this point must be equal to the total head at the end of the duct plus the losses that have occurred between the two points. Let f be the friction loss in the straight duct, s the shock loss in the dif- fuser, and V2 the velocity at the end of the duct. Then h+ v12/2g=v22/2g + f + s FIG. 1.-FAN ON DUCT. A curve showing the value of the left-hand side of the equation for different rates of flow is the total pressure characteristic of the fan, while a curve showing the value of the right-hand side is the total pressure characteristic of the duct. If these two curves are plotted on the same chart, the intersection indicates the rate of flow when steady flow is established.

Jan 1, 1930

By R. J. Charles

PREVIOUS study' of simple impact systems indicated that energy required for fracture and size reduction of brittle materials is greatly dependent on the type of loading that is employed. In this regard it was postulated that fracture and size reduction of a brittle specimen might be accomplished by a high velocity impact at an energy level at which a low velocity impact would leave the specimen relatively undamaged. The finite time required to propagate energy away from the point of loading of an impacted object to other parts of the object and to its supports may permit a concentration of energy at the point of impact if the rate of loading is high. Localizing of energy at the point of impact could quickly initiate fractures that would propagate through the impacted material along with the traveling stress waves. As the cracks form, the initially absorbed strain energy would be released and portions of it travel ahead of the wack tips as stress waves. These secondary stress waves, combined with the initial stress waves derived from the impact, would produce high localized strain conditions in front of the fracture zone. The fracture zone would propagate and the specimen shatter. High rates of loading are brought about by short impact times, in turn obtained by employing high velocity projectiles that are of small mass compared to the impacted object. In the case of a low velocity impact, at an energy level equal to that of a high velocity impact that causes fracture, loading rate would be relatively

Jan 1, 1957

By Howard R. Hume, Terry R. West, William R. Judd

One of the outcomes of a sector slope design in a large open pit in the western United States has been the scrutiny of the structural domain concept. These domains essentially define the area of influence of particular structural characteristics. In the present instance these structural characteristics are joint discontinuities. One of the major drawbacks of defining a domain is that unless large quantities of discontinuity data are available this process of definition is largely qualitative in nature. Viewed from a discontinuity analysis aspect the orientations of all the major joint sets at a given point are a concise descriptor of the structural geologic regime at that location. This is important to domain boundary definition, this in turn is extremely important for assigning which joint sets to use as input for slope stability analysis in a given discontinuity domain. An attempt has been made to develop a quantitative method for defining these discontinuity domains based on limited amounts of orientation data thereby reducing the subjectivity normally involved in such operations. Subjectivity is not always a problem if large quantities of joint orientation data are available, since the mean and variance of joint clusters always can be compared and then grouped to define these domains. However, even this method suffers from the problem that only a single joint set orientation can be considered at a time during the grouping process. On the other hand a discontinuity domain requires that all joint sets at a point be considered simultaneously to truly define the structural discontinuity character of that point. This provides a far more complete

Jan 1, 1982

By E. Buehler, J. E. Kunzler

High-pu.1-ity molybdenum has been heat treated, melted, and zone refined and the physical and chemical changes that are produced by these processes have been studied by making resistance ratio measurements. Pronounced effects are observed that are associated with recrystalliza-tion at about 1200°C and with melting. Melting alone is found to result in a substantial purification by the evaporation of impurities such as iron. Zone refining is found to be reasonably effective with four passes producing a three-fold decrease in resistance ratio and a minimum ratio of 0.0003. With the aid of low temperature measurenzents, it has been shown that the build-up of a deposit of the material being zone refined on the radio frequency coil used for heating can lead to contamination of the sample. CONSIDERABLE interest in high-purity refractory metals for the study of mechanical properties has developed during recent years. Also the need for highly pure metals in certain fundamental studies, such as electronic band structure, has become quite widely appreciated. Molybdenum can now be produced with sufficiently high purity to make it attractive for such investigations. The most suitable measure of chemical purity of metals used for many of these studies is its resistance ratio, R,.,o,/Ro, During the purification of molybdenum by zone refining and its subsequent evaluation by this technique, a number of informative observations were made. These observations concern the effectiveness of zone refining, the volatilization of impurities at the melting point, and the recrystallization of molybdenum and appear to be pertinent to other refractory metals. Also, the usefulness of low-temperature resistance measurements as an analytical tool for evaluating the presence of chemical impurities and physical defects in metals is again illustrated. Samples of high-purity molybdenum of known mechanical history were heated to various temperatures between 800°c and their melting point. Resistance ratios of the samples were measured after they had been given a specified treatment. The data were used, along with mass spectrographic analysis, as an aid in interpreting the nature of the processes that occurred in conjunction with each treatment. Changes in the concentrations of chemical impurities and physical defects are typical of things that effect the low-temperature resistivity. SAMPLES The starting material was obtained from Westing-house Corp., Bloomfield, N.J. It was in the form of molybdenum rods, usually 1/8 or 3/16 in. in diameter. These had been previously processed from bars, 5/8 in, in diameter, originally reduced from 4 in. diam arc-cast ingots, by hot swaging at about 1300°c. In the final step, the temperature was lowered to about l lOO°C which resulted in the production of elongated grains. Typical grains were about 0.03 mm thick and 0.6 mm long. The molybdenum was quite pure as is indicated by the results of mass spectro-scopic analysis1 given in Column 2 of Table I. Other nongaseous elements not listed in the table were not detected. ZONE REFINING AND THERMAL TREATMENT OF SAMPLES Several sample rods, 8 to 10 in. long, were zone refined or were heat treated at several temperatures. Both types of operations were performed using 3 me-

Jan 1, 1962

By C. G. Dunn, F. W. Daniels, M. J. Bolton

IN recent papers on interface energies in metals¹,² the concept of an equilibrium of forces has been used in the measurement of interfacial tensions. Mathematically the equilibrium of three forces is given by the relations: where the 2's are the interfacial tensions (interface energies per unit area of interface) of three phases or grains meeting at angles 21 22 and 23 (212 relates to the 1-2 boundary formed by grains 1 and 2;223 to the 2-3 boundary, etc.). If these relationships are valid, one can calculate relative values of the interface energies from measured boundary angles on specimens which have been brought to equilibrium. Since Eq 1 may be derived through a mathematical process of minimizing the grain boundary energy under the restriction that the ?'s be independent of boundary orientation: the concepts of surface tensions and equilibrium of forces are not particularly essential. To deal with the general case involving dependence of boundary energy on boundary orientation, it becomes desirable to drop certain concepts formerly held (namely that energy per unit area is identical with force per unit length or surface tension) and to use the energy concept alone. It is appropriate, therefore, to use E in place of ? in deriving and using the more general equations that express the anisotropic nature of the grain boundary energy. Herring3# ' recently has derived the required general equations using the principle of minimization of energy. Specifying the boundary orientations in terms of angles (4) measured with reference to crystal axes within the grains, Herring's equations take the form E23 + E21 cos?8 + E12 cos?2 — sin ?12 + sin?2-?E12/?12 =O [2] where the partial derivatives are measured in the direction of counterclockwise rotation of the boundaries. Eq 2 implies that an infinitesimal displacement of the triple point along the 2-3 boundary produces no change in the boundary energy. Similar equations apply for infinitesimal displacements along each of the other two boundaries. From such equations Herring obtains the following general relationship (1 + E1 E2) sin?8 + (E2 — E1) cos?3 ________ E38______________ = (1+ E2 E8) sin ?1+ (E3— E2) cos ?1 __________^5____________[3] (1 + E sin ?2, + (E1 — E8,) COS ?2 1 E28 where E1 = 1/E23- E25 and PC and c8 have similar expressions. It is apparent that Eq 3 reduces to Eq 1 when the c's vanish. Eq 3 also reduces to Eq 1 when the E'S are all equal. Shockley and Read' have pointed out one limitation to these equations. When E plotted versus 4 appears as an energy cusp, as their theory requires, for example, for the energy near a twin boundary position, then Eq 3 (and therefore Eq 1 also) no longer applies if one boundary is in the minimum energy position. One of the equations of form Eq 2, however, applies if the infinitesimal displacement is along the boundary associated with the energy cusp. From the foregoing treatment it will be apparent that equilibrium angles alone are not sufficient in general for calculating relative interface energies.

Jan 1, 1951

By M. E. Wadsworth, J. S. Cho

Colloidal silica dissolved in aqueous suspensions of high surface area thoria was permitted to adsorb on the thoria surface. Silica in three forms was identified by means of infrared spectroscopy and characterized by Si-O vibrational modes in the 9.0 to 10.5 region. A band at 9. 1 was attributed to free unad-sorbed silica, while adsorbed silica resulted in bands of greatest absorbency at 9.4 or 10.3p, depending upon the character of the surface bonding. Size considerations, the amount of silica adsorbed, and the character of the infrared spectrum for strongly adsorbed silica has been interpreted as evidence of formation of chain or layer silica linkages on the thoria surface. Infrared spectroscopy has been used successfully in recent years for the identification of minerals and synthetic inorganic substances. Unfortunately, infrared studies of silicate minerals have not proceeded to the point that unambiguous assignments may be made for Si-O vibrational modes as affected by lattice substitutions and structures. Several investigators have presented infrared spectra of silicate minerals, 1,7 and their work has pointed to the potential value of infrared to identify minerals as well as to note the sensitivity of various Si-O modes to structural and substitutional environments. The strong infrared absorption of various Si-O vibrational modes makes the infrared method a very useful tool for the study of silica adsorbed on the surface of solids of high surface area. Spaepen et a18 studied the adsorption of silica on thoria surfaces from aqueous solutions of silicic acid up to 300°C. A general review of the application of the infrared method to the study of surface adsorption has been presented by Pliskin and Eischens.9 EXPERIMENTAL Du Pont colloidal silica, Ludox SM (16.36% SiO2) and Ludox HS (30.25% SiO2) in aqueous suspensions were used as the sources of silica for the adsorption studies. The thoria used for this study was supplied by Union Carbide Nuclear Co.* under the preparation *Chemical Technology Div., Union Carbide Nuclear Co., Oak Ridge, Tenn. . number D-16-650. It was fired from the oxalate at 650°C and had a surface area of 32.4 ± 0.6 m2 per g measured by nitrogen adsorption. The chemical analysis of the D-16 thoria in ppm was: CO3= (5500), NO3- (< 4), so4±PO4 (100), and Si (20). The Ludox silica was placed in contact with the thoria in a two-liter autoclave10 between room temperature and 250°C. Slurries were made by placing 1 g of thoria in one liter of distilled water containing various additions of the silica sol. Samples were removed from the autoclave by opening a small stainless steel valve. Extracted samples were centrifuged for 10 min and excess solution was decanted. The sample was then dried for several hours at 80°C. Infrared samples were prepared by thoroughly mixing 10 mg of the thoria with 400 mg KBr in polystyrene vials on a "Wig-L-Bug" amalgamator. Pellets were pressed under vacuum and had final dimensions of 1.2 cm diam and 1.2 mm thick. Infrared spectra were

Jan 1, 1963

By O. D. Gonzalez

ThIS communication presents the results of a determination of the permeabilities of hydrogen and deuterium in a iron from 360° to 560°C. Recently Heu-mann and primas&apos; have given values of the diffusivity and solubility in a iron of the two isotopes from which the permeability can be calculated. The work reported in the present communication, however, is a direct measurement of the rate of permeation of the isotopes through an identical iron specimen under the same conditions, so that systematic errors can be minimized in the calculation of the ratio of the permeabilities—the value which is usually of main importance in establishing limits for isotopic differences in diffusive processes. Experimentally the procedure used was the usual one: a steady-state flow of gas produced by a pressure difference across an iron membrane was observed as the pressure rise with time in a previously evacuated, calibrated volume connected to the outlet side of the membrane, while a constant pressure of gas was maintained on the opposite inlet side. The membrane was a cylindrical tube 9.38 cm long, 0.730 cm inside diam, 0.187 cm wall thickness, fabricated of 99.95 pct vacuum-melted National Research Corp. iron (less than 0.003 pct C). One end was sealed by a heliarc-welded iron (99.95 pctj lid of 0.147 cm thickness; the other end of the tube was welded to a 304 stainless-steel tube (0.318 cm ID and 0.318 cm wall) which connects to a vacuum system and to the calibrated volume including a dibutylphthalate manometer. The temperature of the iron membrane was maintained constant to ±0.l°C and was measured with an iron-constantan thermocouple which was calibrated against a standard Pt/Pt-Rh thermocouple: the temperature variation along the length of the membrane did not exceed ±0.5°C. Hydrogen was allowed to pass through the membrane assembly for 72 hr at 615°C before permeability measurements were begun. The system was tested at temperature before and after the experiments by a substitution of helium for hydrogen in the inlet side; under these conditions the pressure rise observed in the outlet side was negligible at all times. The gases used for the permeability measurements were 99.95 pct Matheson prepurified H2 and 99.7 pct D2 (0.3 pct HD) from the Isomet Corp. The gases were dried with liquid N2 before use. In Fig. 1 the logarithms of observed flows, jt, for a pressure difference of 73.4 cm Hg are plotted against T-1 Each point in Fig. 1 represents the slope determined by a least-square evaluation of a plot of the pressure in the outlet side of the membrane against time, including at least two separate sets of observations. Each point in the figure has an uncertainty of ±0.6 pct arising from the experimental uncertainty in the pressure and time measurements. The standard deviation of the observed pressures from the straight lines in all cases is less than the experimental precision of the measurements. The observed flow, jt, includes a small but not negligible flow through the stainless-steel connection.

Jan 1, 1968

By M. K. Yen, W. R. Hibbard

Previous studies of plastic deformation of metals have emphasized the important role of bending and constraints during strain under relatively pure stresses.1"5 Some new phenomena such as early conjugate slip6 and polygonization7 are intimately concerned with the relief of bending stresses, the former by slip and the latter by a process analogous to re-crystallization. However, few analyses of the bending deformation of single crystals were found in the literature, and those8,9 are sufficiently previous to the modern interpretations of slip to invite further investigation in this area. The transverse bending mode of testing, using the two-point loading method, was selected because the center portion of the specimen may be considered as under a theoretically pure bending stress with a uniform bending moment. Considerable attention was given to both the lattice distortion and flow characteristics of the crystals during deformation. Experimental Proeedare A specimen under the action of equal and opposite couples at both ends is said to undergo pure bending. The shear and moment diagrams of a specimen under the two-point loading method of transverse bending are shown in Fig 1. The moment over the middle-third of the span is equal to PL/6, and the vertical shear is zero. Fig 2 (A) illustrates the stress distribution in the elastic range on a plane across the middle of the specimen. It can be seen that the normal stress has a maximum value at the extreme surfaces on the tension and compression sides, and decreases proportionately to zero as it approaches the neutral plane. However, when the plastic range is reached, the stress distribution is no longer a straight line relation, but changes in a manner which can be best illustrated as shown in Fig 2(B). The following calculation and stress analysis are mainly in accordance with the works reported by Timoshenkol0 and Kochendörfer.9 From the simple beam formula, the maximum normal stress will occur at the surface of the specimen. For a round specimen with a radius r and for a rectangular specimen with a height 2h and width 2b, the maximum normal stress, Sp, will be given by the following formulas: For round specimen: 2PL Sp = 3pr3 [1] For rectangular specimen: Sn = 8bh2 [2] Since it is reasonable to consider that slip takes place under the same conditions as in uniaxial loading, the resolved shear stress S?, along the operative slip direction will be as follows: For round specimen: 2PL sin x cos ? Sp = 3pr3 sin x cos ? [3] For rectangular specimen: PL S8 = 8bh2 sin x cos ? [4] where X is the angle between the specimen axis and the slip direction and X, the angle between the specimen axis and the major axis of the glide ellipse. It was also reported by Kochenclorfer9 that the critical bending moment, that is, the bending moment exerted on the specimen to initiate slip, should be higher than the value given by the equations stated above. Based

Jan 1, 1950

By D. A. Stevenson, T. Alden, J. Wulff

A portion of the liquidus curve has been determined for the binary alloy systems Ni-Pb and Cr-Pb. The solubility of nickel is 0.53 atomic pet at 372° and 18.63 atomic pet at 1200°C. Chromium shows low solubility, 0.634 atomic pet at 1210°C. Molybdenum and tungsten were also studied and found insoluble in lead, less than 0.005 atomic pet at 1200°C. INCREASED use of liquid metals of low melting X point for heat transfer, coating, joining, and other purposes has renewed interest in the solubility of structural metals in these liquids. A study of Hansen1 and current literature indicates that few liquidus curves at the low melting end of the binary diagrams have been accurately delineated. This statement applies particularly to the binaries of lead. The present paper is limited to nickel, chromium, tungsten, and molybdenum in lead. In early studies2, 3 of the lead end of the Pb-Ni system, a monotectic at 1340°C was established. Tammann and Oelsen&apos; determined the solid solubility of nickel in lead at 20°C to be 0.023 wt pet. Recently Pelzel5 determined the liquidus curve from the eutectic temperature of 327° up to 727°C using a segregation method. In the present paper this part of the curve has been checked and extended to 1244°C. The Pb-Cr system was first studied by Hindrichs.6 He pointed out the existence of a monotectic at 1470°C and indicated a tentative liquidus. Recent corrosion studies of Fe-Cr alloys in lead suggest that chromium is more soluble than iron in lead.7-8 The solubility of tungsten in lead according to Inouye8 is about 30 wt pet at 1200°C. Appreciable solubility of molybdenum in lead might therefore be expected. Experimental Various experimental techniques have been employed in the determination of solubility in liquid metals. For low solubility, thermal analysis is unsatisfactory. A segregation method was used by Pelzel3 in his study of the Pb-Ni system. In this procedure separation of liquid and solid is possible due to difference in density. In the technique of Kleppa10 a single piece of material is maintained in contact with the liquid metal in evacuated Vycor vials. After equilibration, solid and liquid are separated by tilting. Keck and Broder" measured the weight of a piece of the solid solute before and after immersion in a pure solvent bath; the weight loss was a measure of the solubility. All of the above procedures are time-consuming since they permit only one determination per run. Numerous samples for analysis may be taken from the melt in the method described by Gurinsky and CO-workers.10 The rate of extraction of samples is limited only by the time required for equilibration. In the present work, a modification of this method was employed. A 150-g charge of analytical reagent grade lead and the added metal* were contained in an Alun- dum crucible. It rested on firiely divided silica at the closed end of a 45 mm Vycor tube, 500 mm long. The top of the tube was provided with an inlet and

Jan 1, 1959

By C. W. Spencer, Che-Yu Li, R. J. Knight

The usual reaction product for the monotectic reaction in the Bi-Se system consists of rod -shaped particles of selenium-rich liquid embedded in a single crystal matrix of At certain crystallo-graphic orientations of the matrix with respect to the reaction interface, more complex shapes are as -sumed by the liquid particles. This reaction has been examined at different growth rates and relative crystallographic orientations of the matrix with respect to the reaction interface. The uhriation in auerage particle size of the liquid phase with reaction rate has been determined at one crystallograpIzic orientation of the matrix. On a plot of logarithm of average particle diameter vs logarithm of reaction rate, data points for crystals grown at rates of 10- to 1.0 cm per hr fall near a curve of slobe -0.4. MONOTECTIC reactions in binary alloy systems are reactions of the eutectic class in which, as the system is cooled through the three-phase reaction isotherm, one liquid phase (L) decomposes to a solid phase and another liquid phase (LII).&apos; A partial phase diagram, as taken from Hansen, showing the monotectic reaction in the Bi-Se system is given in Fig. 1. This diagram specifies the monotectic point at 618°C and 72 at. pct Se, and the monotectic reaction products as the intermetallic Bi Se3 and a liquid (LII) which contains approximately 98 at. pct Se. At a lower temperature, 217°C, this liquid may undergo a eutectic reaction in which the reaction products are BizSe3 and crystalline selenium. However, under conditions of rapid cooling, or quenching, from above 217°C, this selenium-rich liquid may be partially retained to room temperature in an amorphous or glassy state. The intermetallic BizSe3 is rhombohedral, of the space group jm;&apos; however, for convenience it is usually represented by a hexagonal struture. A pronounced plane of cleavage, which lies perpendicular to the main axis of the rhombohedral unit cell or parallel to the basal plane of the hexagonal cell, exists in the structure. The usual monotectic reaction product consists of rod-like particles of LII embedded in a single-crystal matrix of BizSe3, although at certain crystallographic orientations of the matrix BizSe3 other more complex shapes are assumed by LII. A similar rod-like, or cylindrical, morphology for the carbide phase has been reported by westbrook7 in the a Cr-Crz3Ce eutectic structure. In this paper the morphological characteristics of the LII particles, as retained to room temperature, have been examined under conditions of varying growth rate and crystallographic orientation of the matrix BizSe3 with respect to the growth direction. EXPERIMENTAL PROCEDURE Alloy specimens corresponding to the monotectic composition, 72 at. pct, or 50 w pct Se, were prepared from 99.999 pct pure bismuth and selenium obtained from the American Smelting and Refining Co. The two elements, corresponding to a total specimen weight of approximately 30 g, were encapsulated in 13 mm OD Vycor tubing under a vacuum of 5 x X mm of Hg. The capsules were suspended on a fine platinum wire in a Bridgman-type furnace which exhibited a temperature gradient of

Jan 1, 1963

By Walter Rose

It is the purpose of this note to call attention to the circumstance complicating the attainment of uniform gas-liquid distributions in multi-phase flow systems, and especially in those of the so-called Hassler type.&apos; Although the complication arises directly as a consequence of gas compressibility and the dependence of fluid distributions on interfacial curvature phenomena, little reference to the problem has yet appeared in the literature.&apos; In fact, it is only the paper of Geffen et al.3 which gives any experimental evidence that a problem exists. On the other hand, previous authorsl,4,5 have made the tacit, albeit fallaceous assumption that uniform gas-liquid distributions automatically are established in linear flow systems by the expedient of maintaining the pressure gradients equal in the flowing gas and liquid phases. Such a device, it can be shown, will succeed only if the immiscible fluids are both equally compressible or both essentially non-compressible. Another necessary condition required before uniform fluid-fluid distributions can be achieved is that the porous matrix is isotropic. Uniform fluid saturation distribution conditions obtain in isotropic media only when the curvature of each interface of contact between wetting and non-wetting fluids is everywhere the same throughout the interspaces. This is a necessary condition which follows from the consideration that variation in interfacial curvature gives rise to finite capillary pressure gradients and therefore to variation in the saturation distribution. That this is not a sufficient condition follows from the consideration that hysteric possibilities allow for different saturations even though the capillary pressure gradient is zero. In any event, it will- be recalled that it is the intent in the Hassler scheme of relative permeability determination&apos; to obtain initially (by the capillary pressure drainage or imhibition process) uniform conditions of fluid distribution in the core sample, and then to maintain this uniformity during mixture flow so that the resultant fluid mobilities which are calculated will refer to steady-state transfer under fixed conditions of uniform saturation. If the flowing fluids are incompressible, it is recognized that employment of the same value of the pressure gradient in each fluid will result in maintenance of the initially obtained condition of zero capillary pressure gradient. On the other hand, the consequence of gas compressibility is that the gradient in the gas pressure varies from point to point in the flowing stream. and since the pressure gradient in an incompressible liquid is constant it is thus impossible to maintain zero capillary pressure gradient during the simultaneous flow of gas-liquid mixtures. Therefore, one would expect to observe a variation in the gas-liquid saturation in the directions of the capillary pressure gradients, depending in magnitude on the particular way saturation changed with capillary pressure. In order to formulate the manner gas compressibility effects prevent the attainment of uniform gas-liquid distributions during mixture flow, consider a linear flow system of unit length. As noted, it is necessary to assume an isotropic medium (viz. one where permeability is independent of position and direction). One then can arbitrarily set the pressure

Jan 1, 1951

By Walter Rose

It is the purpose of this note to call attention to the circumstance complicating the attainment of uniform gas-liquid distributions in multi-phase flow systems, and especially in those of the so-called Hassler type.&apos; Although the complication arises directly as a consequence of gas compressibility and the dependence of fluid distributions on interfacial curvature phenomena, little reference to the problem has yet appeared in the literature.&apos; In fact, it is only the paper of Geffen et al.3 which gives any experimental evidence that a problem exists. On the other hand, previous authorsl,4,5 have made the tacit, albeit fallaceous assumption that uniform gas-liquid distributions automatically are established in linear flow systems by the expedient of maintaining the pressure gradients equal in the flowing gas and liquid phases. Such a device, it can be shown, will succeed only if the immiscible fluids are both equally compressible or both essentially non-compressible. Another necessary condition required before uniform fluid-fluid distributions can be achieved is that the porous matrix is isotropic. Uniform fluid saturation distribution conditions obtain in isotropic media only when the curvature of each interface of contact between wetting and non-wetting fluids is everywhere the same throughout the interspaces. This is a necessary condition which follows from the consideration that variation in interfacial curvature gives rise to finite capillary pressure gradients and therefore to variation in the saturation distribution. That this is not a sufficient condition follows from the consideration that hysteric possibilities allow for different saturations even though the capillary pressure gradient is zero. In any event, it will- be recalled that it is the intent in the Hassler scheme of relative permeability determination&apos; to obtain initially (by the capillary pressure drainage or imhibition process) uniform conditions of fluid distribution in the core sample, and then to maintain this uniformity during mixture flow so that the resultant fluid mobilities which are calculated will refer to steady-state transfer under fixed conditions of uniform saturation. If the flowing fluids are incompressible, it is recognized that employment of the same value of the pressure gradient in each fluid will result in maintenance of the initially obtained condition of zero capillary pressure gradient. On the other hand, the consequence of gas compressibility is that the gradient in the gas pressure varies from point to point in the flowing stream. and since the pressure gradient in an incompressible liquid is constant it is thus impossible to maintain zero capillary pressure gradient during the simultaneous flow of gas-liquid mixtures. Therefore, one would expect to observe a variation in the gas-liquid saturation in the directions of the capillary pressure gradients, depending in magnitude on the particular way saturation changed with capillary pressure. In order to formulate the manner gas compressibility effects prevent the attainment of uniform gas-liquid distributions during mixture flow, consider a linear flow system of unit length. As noted, it is necessary to assume an isotropic medium (viz. one where permeability is independent of position and direction). One then can arbitrarily set the pressure

Jan 1, 1951

By A. F. Meger

Coal treatment by oil spraying receives special attention at the Georgetown plant for the dividends it pays in satisfying present customers and attracting new markets. Customer satisfaction requires care, quality control, and use of suitable oils. REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal CO. who have helped develop, over a number of years, an efficient and flexible method for spraying controlled amounts of oil on coal. Since the Georgetown preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage. The graph, Fig. 1, shows results of the original tests made with a 700-sec residual blend and a 500-sec lubricating oil on Georgetown stoker coal of 1¼x3/8-in. size.* The advantages of better price, improperly blended can raise havoc. Some.,pale oils also, although odorless when delivered, give off a sweet sickening odor when atomized under pressure. It is recommended that all products be tested before they are used. There is a specific place for all spraying oils. For example, at a power plant a severe dust condition exists around the stockpile area and in parts of the plant. The cheapest spraying oil made, regardless of odor, will do an excellent job in this case and will save the company 3 to 5c per gal or more. Domestic trade, on the other hand, must be carefully handled to prevent complaints about odor, and the only way to do this is to stay with the proved products after the odor tests have been made. The preparation plant at Georgetown has facilities to handle either tank car or tank truck deliveries. Steam is available at the unloading point if the weather is severe, and there is an indicator at the unloading point to prevent overflowing the 20,000-gal underground storage tank. Systematic test samples are removed from each delivery and sent to the lubrication engineer to insure quality control. Fig. 3 illustrates the chutes in which smaller sizes of coal are treated. Fig. 4 shows the entire spraying system. Buried in the ground is a 20,000-gal tank with immersion heaters grouped around the feeder line to insure adequate gravity flow to the pump under all conditions of weather. Oil flows to a 500-gal preheating tank where the temperature is kept about 150°F by six 1½-kw immersion heaters thermostatically controlled. Hot oil is fed through a self-cleaning disc-type filter to the hydraulic pump. Valves and piping make it possible to transfer oil from one tank to another or to drain the lines for maintenance purposes. All this equipment is below ground level in a covered pump room,

Jan 1, 1955

By F. Kurata, A. F. Bertuzzi, P. C. Davis, T. L. Gore

The phase and volumetric properties of 10 very volatile mixtures are presented for temperatures from — 200°F to above the critical points. These mixtures consisted of natural gases and of mixtures of natural gases with methane and nitrogen. Existing correlations of compressibility factors have been extended to apply to these mixtures. Existing correlations of critical pressures and temperatures do not apply to these mixtures. Methods have been developed for estimating critical temperatures of these mixtures to ± 4°F and critical pressures to 2 5 per cent. These methods apply to other volatile and very volatile mixtures. The results of this work are particularly applicable to the separation of nitrogen from hydrocarbons by low-temperature distillation. INTRODUCTION Knowledge of the low-temperature phase and volumetric properties of natural gases and of other mixtures of the light hydrocarbons is becoming increasingly important as interest in low-temperature separation processes increases. Low-temperature distillation has been used to separate ethane and ethylene from natural gas and from refinery gases for petrochemical uses. Removal of nitrogen from natural gas by low-temperature distillation has been proposed 7,20 as a means of increasing the capacity of existing gas transmission lines and of improving the marketability of the gas. Further application of low-temperature separation processes has been retarded by lack of data on the phase and volumetric behavior of mixtures at low-temperatures and at high pressures. This paper presents the results of determination of the phase and volumetric properties of 10 very volatile mixtures at temperatures from - 200 °F to above the critical point. These mixtures consisted of natural gases with methane and nitrogen. Generalized methods are presented for estimating the critical temperatures, critical pressures, and the densities of such mixtures. EXPERIMENTAL APPARATUS AND PROCEDURES The apparatus and the experimental procedures have been described in an earlier paper13. The method consists of displacing the mixture from a reservoir which is maintained at constant temperature and pressure into an agitated glass equilibrium cell which is maintained at constant temperature. The liquid level within the glass equilibrium cell was visually observed, and the pressure was measured to within & 3 psi with a calibrated Bourdon gage. COMPOSITIONS OF MIXTURES STUDIED The compositions of the mixtures studied are summarized in Table 1. The measured properties included in Table 1 will be discussed later in this paper. The sources of these gases are described below: Gas "A-1&apos;&apos; was obtained from the Phillips Petroleum Co. Its composition was reported in connection with earlier work." The properties of this gas were reported in an earlier paper.13 Gases "A-2, A-3, A-4" were prepared by mixing nitrogen with gas "A-1." Gas "AB-1" was prepared by mixing methane with gas "A-1." The properties of this gas were reported in an earlier paper.&apos;" Gases "AB-2" and "AB-3" were prepared by mixing nitrogen with gas "AB-1." Gas "B" was obtained by W. W. Bodle of J, F. Pritchard & Co. from the primary separator of a well in western Kansas. Gas "C" was obtained from a Cities Service Co. pipeline at Lawrence, Kans. Gas "D" was prepared by mixing gas "AB" with gas "C."

Jan 1, 1955

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.&apos; The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.&apos; Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

DISCUSSION, T. B. King and H. H. Kellogg, Chairmen Philipp Gross (Fulmer Research Institute Ltd., Stoke Poges, England)—As pointed out by the author, any better agreement between experimental and calculated

Jan 1, 1956

By AIME AIME

WEDNESDAY night, by long tradition, is al- ways set aside for the annual dinner, even when, as it was this year, it is Ash Wednesday. Whether the somewhat smaller attendance than last year is attributable to that cause, the unexpectedly long persistence of business depression, or whatever may have been the reason, it was a joyous occasion, and the grand ball-room of the Commodore Hotel was as completely filled With diners as * was consistent with com- fort. In the half hour before the dinner was actually served the guests assembled in an adjoining room and not only exchanged greetings but proceeded along the receiving line to greet the guests of honor. The number present was so large that hardly more than half of them had been able to do this before the summons to the dining room sounded and a hearty and immediate response was made to it. Toy balloons at each plate, inflated and directed at the heads of companions or nearby friends, but which were just as likely to carom from the nose of a hurrying waiter, successfully broke the ice as well as not a few plates. It would be interesting to know whether the pleasure the guests derive from these de- vices is in part based on the all-too evident annoyance of the waiters, and what the relative quantitative relationships are.

Jan 1, 1931

By Paul C. Merritt

Chrysotile asbestos producers in Quebec may soon experience a unique situation-i.e., strong competition from American ore sources for the short fiber market west of the Mississippi River. This com- petition will be forthcoming from Copperopolis and Coalinga, two deposits now being developed on opposite flanks of the San Joaquin Valley in central California. The combined output now planned from both deposits is 100,000 tons annually, equivalent to about 50% of the annual market demand in the western, central and Gulf States, and more than twice the tonnage sold in 1960 by all other American asbestos producers combined. The principal companies involved in these new undertakings are Jefferson Lake Asbestos Corp. (subsidiary of Jefferson Lake Sulphur Co.), Hidden Splendor Mining Co., Coalinga Asbestos Co. (Johns- Manville Corp. in conjunction with Kern County Land Co.), Union Carbide Corp., and Asbestos Corp. Ltd. Jefferson Lake&apos;s principal interest is at Copperopolis where the company&apos;s new 70,000-ton per yr mill recently went on stream. The company also holds some claims at Coalinga, but this latter area is better known as the site where Hidden Splendor, Coalinga Asbestos Co. and Todd Industries (a local company) have established operating mines and mills capable of turning out 30,000 tons of fiber each year. Coalinga is also the site of exploration by Union Carbide Nuclear and Asbestos Corp. Ltd.

Jan 9, 1962

By Fred Bond

WHEN some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material, and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media dur-ing normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many com-mercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an im-portant one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain labora-tory tests were made from which it was found that different materials form coat-ings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qual-ities, like coal and graphite.

Jan 1, 1940

By A. E. Gorum, J. Washburn, E. R. Parker

Experimental evidence was obtained in support of the idea that cleavage fracture can be initiated by dislocation pile-up. The high ductility of MgO crystals when tested in bending comPared to their relative brittleness in tension was explained on the basis that large pile-ups are more likely in a tension specimen. CLEAVAGE fractures have been a problem of major concern for many years. A number of large steel structures have failed in a brittle manner, usually suddenly and without warning; often the failures occurred for no obvious reason and at nominal stress levels well within the generally accepted range. A great deal of data have been collected about factors that contribute to failures,1 but the physics of the fracture process has never been revealed. cottrel12 has recently developed a theory of brittle fracture in ductile materials which was based upon the concept that dislocations moving on two intersecting planes can unite to form a crack nucleus. This theory accounts for the known effect of grain size and for the effect of testing temperature. There has, as yet, been no experimental evidence published that would substantiate this or the earlier theories based on stress concentrations due to piled-up dislocations. The study reported herein was conducted to obtain information that would either substantiate or disprove the

Jan 1, 1960