Search Documents

By Warren W. Jamar, Philip D. Pearson

IN recent years, there have been many changes in mining operations in the Lake Superior district. To follow these trends on the Menominee Range of Michigan, information has been assembled from all of the iron informatior]mining operations in the area. There are 15 operating underground mines in the Iron River-Crystal Falls area of the Menominee Range. Within the past two years, two idle properties were reopened pasttwoyears,and are now producing, and a third and fourth are being reopened. Also, there are two siliceous openpits operated by independent companies outside this immediate area. Six companies operate the underground mines, employing some 1850 employees. Table I shows pertinent facts about these properties. During 1949, the largest mine in Iron County shipped 571,287 tons, and one of the newer mines shipped 39,378 tons, with a range total to 3,535,-373 tons. Since the Menominee Range was opened in the 1870's, the mines in Iron County have shipped 85,890,922 tons. From an operator's viewpoint rather than a geologist's, the ore is' classified as semi-hard, composed of hematite and limonite. It is not as soft as the ores of the Marquette Range nor is it as hard as the hard ores of the Marquette and Vermillion Ranges. The ore bodies have slate hanging walls and slate footwalls. In most cases the hanging walls and footwalls are soft and high in sulphur. The sulphur comes from pyrite, and these slates will ignite when piled more than 6 to 8 ft high. Ore is mined on this range by: 1—Sub-level stop-ing; 2—Shrinkage stoping; 3—Sub-level caving; 4— Block caving; 5—Top slicing. The predominance of these methods is in the order named. Underground drilling is important in the mining cycle. Some changes made and trends toward future changes fall into four categories: Drill bits, drill steel, drill machines, and compressed air pressures. Several types of bits have been tried and are in use. They include the detachable tungsten carbide, insert bit; the intraset steel bit, which is a conventional steel rod with tungsten carbide insert; the one-use bit; and the multiple-use bit. For many years, detachable multiple-use bits have been standard. In tests conducted recently to im- prove drilling efficiency, this bit was used as the basis for comparison. Under existing conditions, a multiple-use bit can be resharpened about three times before it is discarded. A thorough test of 2-in. tungsten carbide threaded bits was conducted under various ground conditions. 1—The drilled footage ranged from 48 to 600 ft per bit; averaging 357 ft per bit. Under these same conditions, a multiple-use bit ranged from 8 to 80 ft per bit. 2—The bit cost was greater for the insert bit in each case. 3—The average drilling speed for the insert bit was 12 in. in 62 sec and for the multiple-use bit was 12 in. in 64 sec. In a second test, 2V4 -in. tungsten carbide bits with the large 1 3/16-in. thread were used in moderately soft ground on a 152-lb drifting drill on a long feed jumbo. 1—The drilled footage ranged from 450 to 5000 ft per bit, averaging 1810 ft per bit. Under these same conditions, a multiple-use bit averaged 64 ft per bit. 2—The bit cost was reduced by the use of the insert bit. 3—No increase in drilling speed was recorded. 4—Minimum footage obtained was caused by thread failure. To improve the thread life, thread size on the rod was increased and the bit was attached to the rod with a pipe wrench. After this, bits failed in equal proportions because of cracked skirts, broken inserts, and gage loss. Tungsten carbide bits are now used in the operation where this second test was conducted because labor costs were lowered as a result of reducing the number of bits being changed by the miners. At the same operation and under the same conditions as the second test, 1Y4-in. insert bits with standard 1-in. threads were used. These bits did not drill much more than 300 ft before thread failure and were then welded to the rods and used until total failure. Sometimes this footage was considerable, sometimes it was not. Chisel-type 2%-in. insert bits were

Jan 1, 1952

By T. A. Rickard

The interior of West Australia is an arid table-land, elevated 1400 feet above the sea. This plateau is flanked to the south by the Tertiary limestones which fringe the Great Australian Bight. It is bordered northward by the Carboniferous beds of the Fitzroy river and westward by the granite of the Darling hills, while to the cast this wide area, about 900 miles square, slopes downward imperceptibly into an undulating plain of sand, which stretches with dismal persistence across the boundary of South Australia. The waters of the ocean receded from this tract of land long ago; it is probably the oldest landsurface on the globe, and represents the basal wreck of a much larger continent. Fig. 1 is a map of this region. The Coolgardie and Kalgoorlie gold-fields are situated in the southwestern part of the region. The rock-formation consists of granite penetrated by diorites and andesites. The latter are occasionally associated with tuff's, which have been readily mistaken for sedimentaries. There are no fossil-bearing rocks, such as would afford a datum-line from which to measure the relative geological age of the prevailing formation. On the extreme edges of the mining territory there are, it is true, remnants of sand-rock which are considered identical with the " Desert Sandstone " of Queensland, determined by Daintree to be of Mesozoic age. But even this formation has evidently been laid down so long subsequent to the underlying rocks that it serves merely to emphasize their much greater antiquity. In their characteristics and in their relations to each other, the granite and the diorite of the Coolgardie region appear to me much to resemble the Laurentian granite and the Huronian

Jan 1, 1899

By T. Egleston

The Boston and Colorado Smelting Works are situated in the town of Black Hawk, Gilpin County, Colorado, on the Clear Creek Narrow Gauge Railway, 55 miles from Denver, in the Rocky Mountains, at an altitude of 7800 feet. It was one of the first works erected for the metallurgical treatment of gold ores, and the only one established in Colorado on a large scale which has been uniformly successful. Both gold and silver ores are treated, and gold, silver, and copper produced. The lead is not separated from the ores nor paid for, if it exists, and is entirely lost in the residues. The works were planned and built by Professor Hill, formerly Professor of Chemistry in Brown University, Providence, R. I., and is still managed by him, assisted by Mr. Richard Pearce, formerly professor in the School of Mines at Truro, England. They are very advantageously situated with regard to the ore-producing regions, having Boulder County on the north, which produces, besides ordinary gold ores, a series of tellurium minerals, such as altaite, sylvanite, and hessite, which are very rich in gold and silver. They are associated with copper and iron pyrites, blende, galena, and the carbonate and oxides of iron. Gilpin County itself produces for the most part the pyrites of iron and copper rich in gold, with a small quantity of galena and blende, which is rich in silver. In

By T. PH. D. Egleston

THE Boston and Colorado Smelting Works are situated in the town of Black Hawk, Gilpin County, Colorado, on the Clear Creek Narrow Gauge Railway, 55 miles from Denver, in the Rocky Mountains, at an altitude of 7800 feet. It was one of the first works erected for the metallurgical treatment of gold ores, and the only one established in Colorado on a large scale which has been uniformly successful. Both gold and silver ores are treated, and gold, silver, and copper produced. The lead is not separated from the ores nor paid for, if it exists, and is entirely lost in the residues. The works were planned and built by Professor Hill, formerly Professor of Chemistry in Brown University, Providence, R. I., and is still managed by him, assisted by Mr. Richard Pearce, formerly professor in the School of Mines at Truro, England. They are very advantageously situated with regard to the ore-producing regions, having Boulder County on the north, which produces, besides ordinary gold ores, a series of tellurium minerals, such as altaite, sylvanite, and hessite, which are very rich in gold and silver. They are associated with copper and iron pyrites, blende, galena, and the carbonate and oxides of iron. Gilpin County itself produces for the most part the pyrites of iron and copper rich in gold, with a small quantity of galena and blende, which is rich in silver. In * By consent of the council of the Institute, this paper was first published in London Engineering, from which the engravings are here reproduced.

Jan 1, 1876

By L. D. Frink

Those actively interested in mining are fully aware of the ever-increasing difficulty of making conditions such that efficient work can be done in underground openings, especially as higher rock temperatures are encountered in depth. This is also true where an effort is being made to cut down the burden of overhead expense by working headings 24 hr. in a day if blasting is done as often as is possible in that time. That the conditions resulting from both these causes have driven the native-born Americans from the mines and that their places have been taken by less efficient foreigners is a fact that we must all admit. The great war now being fought in Europe and the educational qualification clause written into our immigration law by the last Congress will probably limit very materially the supply of labor, such as we are now using in our mines, and will force upon mine operators the necessity of making this work appeal again to Americans. Metal tubing, with blower or exhaust fans, has long been used in supplying air to dead ends where natural ventilation is impossible, or in driving the smoke from such places, or in doing both, as the need might be. Here in Butte we have now come to use canvas tubing very extensively and find that it has many advantages not possessed by the metal. The use of flexible tubing is not new, but it has not been generally used in mining operations. Recent improvements, however, in the canvas itself and in the jointing of sections and manner of suspension have so increased its usefulness that it promises to add much to the efficiency of mining. There is now on the market a product that is impervious to air, is fireproof, and has a system of jointing which permits it to be put up or taken down in a few seconds. In this article an effort will be made to explain the manner in which canvas tubing is being used in the North Butte company's operations at Butte, Mont. The accompanying photographs will, I hope, help make clear what may be done with this material.

Jan 1, 1918

By Earl Bardwell

(Butte Meeting, August, 1913.) THE structural relations existing between cuprous oxide and copper were first systematically studied by Heyn1, who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming .;from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study off the microstructure could be made to yield a correct estimate of the oxygen content of the specimen of refined copper under examination. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing, this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in, this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity.

Jan 7, 1913

By C. H. Mathewson, E. M. Thalheimer

In planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100' C. to 1,000" C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,' in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper. The great importance of copper both as a material of construction and as the base of our most important alloys (aside from steel) has led to innumerable investigations of its properties, particularly in commercial forms. Naturally, the merits of furnace-refined lake coppers us. those of the very pure electrolytic product have furnished the subject of much experimental work and animated discussion, wherein the effect of arsenic has by no means been overlooked. In the literature of the past 10 years,

Jan 1, 1917

By Bruno Nordberg

HOISTING is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.1 In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michi-gan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualisticc types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By F. G. Smith

A few years ago, the writer encountered a problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Mathewson and Phillipsll an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-mm. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures. Preparation of Specimens The material used was cartridge brass 0.400 in. thick, having the following composition: Copper 66.60 per. cent., zinc 33.35 per cent., lead 0.02 per cent., iron 0.03 per cent. This was rolled with 35 per cent. reduction after a 700" C. anneal. Fig. 1 shows the structure of this original bar on which all subsequent anneals were made. Pieces 1 in. (2.5 cm.) wide and 3 in. long were prepared and annealed for 1/2 hr. at 450°, 550°, 650°, '750°, and 850" C. Each of these pieces are indented under the Brinell test with a 10-mm. ball at 500, 1000, 2000, and 3000 kg. pressure. Then, sets of five pieces from each of the original anneals were reannealed at 450°, 550°, 650°, 750°, and 850" C.

Jan 1, 1921

GENERAL GEOLOGIC DESCRIPTION The mineral deposit of this case study can be described as a "typical" porphyry copper deposit of the southwestern USA and northern Mexico mineral province. The copper mineralization is related to Laramide age intrusives of intermediate composition which have been intruded into older, mostly crystalline, host rocks. Post Laramide deformation and faulting have subjected the deposit to erosion, leaching, and enrichment processes, which have created a secondarily enriched chalcocite zone. Later basin and range faulting down dropped the ore zone, resulting in deep burial beneath late Tertiary conglomerates and gravels, thus preserving the deposit from further erosion and oxidation. Lower grade chalcopyrite mineralization constitutes the primary zone underlying the enriched blanket. MANAGEMENT OF SAMPLE DATA Sample data were obtained from exploration diamond drill holes that were collared vertically and drilled with surface rigs. Most of the holes were surveyed downhole and found to deviate significantly from the vertical. The data were keypunched from original drill hole logs to formats as described in Chapter 6. Three types of cards were prepared: 1) A heading card containing the following information: [Project Name Coordi-in_ Hole Collarnates Bear-clina-Total ID Northing Easting Elevinglion Depth] 2) Individual record cards following each heading card with the following information: [SampleMin. Zone interval Assay Fields Leached (enriched ID From-ToTotal Cu Oxide Cu primary)] 3) Where downhole survey data were available, a card was punched for each downhole survey point. The card image looked very much like the heading card, followed immediately after the heading card, and contained the following information: [Hole Sur Point Sur Point Sur Point ID Bearing Inclination Depth] The keypunched data were then processed by the drill hole survey program producing a record file which contained information as follows: [Line 1. Project Name Date Assay Field Identifiers Line 2. Hole ID Northing Easting Elevation Bearing Inclination Number of Samples Line 3 through N+ 2 (where N equals the number of samples in the hole) Top Min. of Min. Zone Zone Sample Sample Coordinates Sample Assays Leach InterLength Northing Fasting Elev Total Cu Oxide Cu (etc) face] MINERAL BOUNDARY PROBLEM AND TREATMENT According to the geologic description, at least three mineral zones are present within the ore limits, as well as fault boundaries and a buried topographic surface, each of which have to be considered. The interfaces of the various mineralogical and geological boundaries were identified as accurately as possible in each drill hole by the project geologist, the location of the interface was surveyed in the computer program in association with the nearest sample intercept to the interface (note last field of line 3). Thus, the boundary is represented as a point in 3D space at each intersecting drill hole. The linear interpolation (LINTERP) program then searched the last field of the surveyed record to find the top of each mineral zone, or geologic boundary, and read the coordinates associated with that sample point. The program then used the coordinates to compute an interpolated surface between all existing data points as described in Chapter 11. A contour map was plotted for each of the computed surfaces and reviewed by the project geologist. Where the surfaces were poorly defined due to lack of real drill hole information, the geologist, at times, inserted a "pseudo" drill hole intercept according to his best judgment and feeling for the configuration of the surface, and such points were entered into the data stream for LINTERP. When the project geologists were satisfied that they had obtained

Jan 1, 1980

By B. C. Allen

Grain boundary grooving has been studied in chromium, molybdenum, and tungsten under a variety of conditions using high vacuum techniques and tantalum -gettered argon. The average surface free energy of solid chromium, and the chromium-liquid silver interface free energy were respectively found to be 2200 ± 250 and 500 i 130 ergs per sq cm from groove formation kinetics and estimates of pertinent volume difffusion coefficients. The results for chromium were unffected by variations in interstitial content ranging from 0.003 to 0.09 pct C, or 0.003 to 0.03 pct O. Surface diffusion is the primary mechanism of groove formation in chromium under 1 atm argon at 1200" to 140O°C, and is essentially unaffected by 0.003 to 0.09 pct C, 0.003 to 0.03 pct O , metastable nitrogen contents up to -0.01 pct, and up to 2 torr Ag vapor. At higher temperatures, the major mechanism is volume diffusion in argon or evaporation-condensation in stutic vacuum. Surface diffusion occurs in molybdenum at 0.5 to 0.96 and in tungsten at 0.5 to 0.9 of the absolute melting tempera -ture by a single mechanism, possibly by the migration of single adatoms or vacancies. Results were slightly affected by up to 23 tory Sn vapor, and in molybdenum were essentially unaffected by 0.5 Ti or carbon in the range 0.002 to 0.02 pct. Volume difffusion through the liquid is the mechanism of groove formation in chromium-liquid silver at 1200" to 1400°C and in molybdenum-, Mo-0.5Ti-, and tungsten-liquid tin at 1200" to 2000°C. The solid-liquid interface free energies involved were estimated from grooving kanetics. WHEN a grain boundary intersects a solid surface, a groove tends to form along the line of intersection at temperatures above about half the absolute melting point (0.5 TM). The groove progressively grows by preferential atomic migration either by diffusion or evaporation. Establishment of a groove angle occurs in accordance with the grain boundary and surface free energies involved. The motivation for groove formation is a reduction in the total surface free energy of the system. This study is a continuation of previous work on thermal grooving of chromium, molybdenum, and tungsten.&apos; The temperature ranges were extended, and the effect of metallic and interstitial impurities was evaluated. The results were such that certain interface free energies and surface self-diffusion coefficients were deduced from the grooving kinetics. EXPERIMENTAL WORK Materials and Preparation. As indicated in Table I, the 0.05-0.08-cm-thick chromium, molybdenum, and tungsten sheet used was nominally 99.99 pct after recrystallization. Two lots of molybdenum with about the same analysis, Mo-0.5Ti,* and tungsten were ob- *Alloy compsitions are expressed in weight percent . tained commercially. Extruded chromium rod,&apos; prepared from iodide process crystals, was warm rolled to sheet at 700°C. Sheet of three Cr-0 impurity alloys containing up to 0.03 pct 0 was prepared by warm rolling arc melted, extruded, and swaged rod. Two Cr-C impurity alloys containing up to 0.09 pct C were made by equilibrating unalloyed chromium with a known amount of CH4 for 24 hr at 1150°C in previously evacuated quartz capsules. Chromium containing nominally 0.015 and 0.06 pct N was similarly prepared by equilibration with NH3. The sheet was recrystallized to give a stable grain size about equal to the sheet thickness. Molybdenum and Mo-O.5Ti were recrystallized in a tantalum resistance furnace 1 hr at 1 x lo-5 torr at 2300" and 220O°C, respectively. Tungsten was similarly annealed for 1 hr at 2500°C. Chromium and its impurity alloys were outgassed at 1100°C and recrystallized 1 hr at 1700°C under 1 atm Ar. Except for nitrogen, the impurity content stayed roughly constant. Nitrogen in both alloys was reduced to <0.001 pct. In fact, over 80 pct of the added nitrogen was lost after outgassing at llOO°C and annealing sheet 1 hr at 1300°C in argon in the presence of tantalum. Such a rapid loss can be rationalized since -2 torr N are required for equilibrium with 0.04 pct N in solution,3 while the equilibrium pressure is ~10-5 torr over tantalum at 1300°C.4 The recrystallized sheet was cut into small coupons which were metallographically ground and polished on one side with a minimum of grain boundary relief. The surface roughness was on the order of 0.01 µ. The tin and silver used were nominally 99.999 spec-trographically pure. After being outgassed at 1100°C and equilibrated in a molybdenum crucible for 0.5 hr at 1800°C in argon, the tin contained 3 ppm 0, <0.3 ppm N, and 0.1 ppm H. Following outgassing at 900°C and equilibration in a chromium crucible 1 hr at 1400°C in argon, the gas content of the silver was 1 ppm O, <0.5 ppm N, and 0.3 ppm H. Grooving Under Argon or Vacuum. All specimens were placed in unsealed containers made from rod or sheet of the same alloy, thereby enabling the polished surface to achieve gas-solid equilibrium. The annealing fixtures are shown in Fig. 1. The specimen was placed in a resistance furnace with a tantalum or Ta-10W heating element plus tantalum fixtures or radiation shields. Chromium was outgassed at 1100°C, and molybdenum and tungsten were outgassed at 1900°C to 1 x l0-5 torr or at the grooving temperature, whichever was lower. In vacuum anneals, the specimen was then heated directly to the intended grooving temperature. In argon anneals, 99.996 Ar was admitted

Jan 1, 1970

By Granville S. Borden

TAXES in general are onerous and are not a pleas- ant subject for discourse. There are, however, some very cogent reasons why we should dedicate a part of our thoughts and services to the solution of our taxation problems: The happiness of every individual in the United States depends on the maintenance of a stable government. The collection of taxes is an indispensable function of a stable government, and the power to collect taxes depends in part on the question whether taxes are fair and equitable. As representatives of the mining industry it is our duty to .protect it from tax burdens that are discriminatory or- unjust, As citizens we find that taxation is incessantly endeavouring to unravel the knots in our purse-strings. Many members of the Institute may be consulted .by clients on taxation problems, especially the phases which re- late to depletion and valuation. It is the hope of the writer that the discussion of some of the current depletion and valuation problems will stimulate interest in the problems, and as a consequence of this new interest facts will be ventilated, opinions rendered and services performed, which will be a means of solving the problems to the satisfaction of all parties interested.

Jan 1, 1929

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,&apos; the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson&apos;s investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.&apos;s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

By J. D. Wood, J. T. Smith

ALLOYS with a dispersed second phase in a metallic matrix are generally much stronger than the matrix itself. Plastic deformation in dispersion-strengthened alloys is usually confined to the matrix phase when recovery processes are active, while in the absence of recovery both phases may yield.&apos; The alloy system studied in the present research was WC-12 wt pct Co and consisted of noncoherent WC particles dispersed in the cobalt matrix. Some particle-to-particle contact existed but not enough to produce a continuous WC skeleton. The microstruc-ture of the WC particles was characterized by very straight edges, forming a trapezoidal shape in any plane of polish. Previous investigations with WC-Co alloys at room temperature have shown that fracture of the WC particles occurs in transverse rupture testing.&apos; Room-temperature slip was reported for WC particles after indentation for hardness measurements.3 Elevated-temperature deformation of WC particles in a WC-12 pct Co alloy was suggested by recent electron microscope studies of specimens deformed at 900&apos; to 1000°C.4 In highly deformed alloys, the WC edges were serrated in contrast to the usual straight or smooth appearance. WC-12 pct Co and WC-15 pct Co alloys have been previously studied under elevated-temperature com-pressive-creep conditions by the present authors. Electron microscope studies of two-stage replicas from deformed specimens showed no evidence of slip or fracture of the WC particles. These specimens were brought to temperature and allowed to equilibrate prior to the application of the creep load. It was believed that the load-application rate, a crosshead speed of 0.005 in. per min on an Instron universal testing machine, was sufficiently low that recovery within the cobalt matrix was sufficient to limit the deformation to this matrix. A series of experiments was performed to evaluate the influence of loading rate on the deformation of WC-Co alloys. A WC-12 pct Co alloy was selected for these determinations. The average WC particle size was 4.45 p with an average linear separation between particles of 0.59 p. The selected temperature was 800°C and was monitored with a Chromel-Alumel thermocouple attached to the specimen. Testing was conducted in an argon-atmosphere chamber to prevent oxidation of the WC-Co specimens. This chamber was mounted on an Instron universal testing machine equipped to apply the load at a fixed rate. Each specimen was loaded to 110,000 psi compression stress at 0.05 and 0.5 in. per min. The loading rate was monitored prior to insertion of the test chamber and was found to be almost precisely the nominal rate selected. The specimens were raised to temperature and held to equilibrate with the surroundings, and then the load was applied and held for 4 hr to duplicate the exposure time utilized for the creep specimens. The time to reach full load at a crosshead speed of 0.005 in. per min was some 500 sec and was reduced to 50 and 5 sec as the loading rate was increased to 0.05 and 0.5 in, per min, respectively. The model developed by Ansell,&apos; when recovery processes do not occur, considers that fracture or deformation of the dispersed particles is necessary to relieve back stresses on dislocation sources and allow dislocations piled up against particles to sweep out in the matrix to cause plastic deformation; he further states that, even at elevated temperatures, the dispersed-particle deformation is necessary for yielding in the absence of recovery. For the case of straight dislocation segments piled up against a straight barrier, such as the straight-sided WC particles, the shear stress, 7 exerted on a particle is: where h is the spacing between particles (0.59 p), a is the applied stress (110,000 psi), p, is the shear modulus of the matrix (6.7 X lo6 psi at 80O°C), and b is the Burgers vector of the matrix dislocation. From Eq. [I], the shear stress, 7, exerted on the WC particles when no recovery occurs is of the order of 6 X lo6 psi at 800°C. The limiting stress, F, that will

Jan 1, 1969

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963

By Eugene Coste

Although some of the observers who first paid especial attention to the occurrences of oil and gas in the strata (such as Hunt in 1859, Andrews in 1861; Winchell in 1865, Mendelejeff in 1876, Höfer in 1876, Minshall in 1881, and I. C. White in 1883) seem to have been impressed with the fact that oil and gas deposits were connected with the disturbances in the rocks caused by their upheavalll yet, with the exception of Mendelejeff, and possibly Andrews, these observers do not appear to have understood what is really the one essential factor in the occurrence of oil and gas in the strata: viz., the faulting, uplifting, fracturing, fis-suring, and jointing always accompanying even slight rock disturbances, and in certain districts (petroliferous provinces)2 allowing solfataric hydrocarbon emanations to force their way up from the interior and to reach and impregnate the porous portions of sediments subjected to the disturbances. Instead of this simple explanation to account -for the observed connection between petroleum deposits and rock disturbances, most of the observers mentioned above, and many others who have foliowed them on the same lines since, have entirely reversed the problem. To them, instead of the dissemination of gases from fissures into the sediments, it presented the accumulation and concentration, according to anticlinal or other geologic structures, of oil and gas originally present throughout the whole mass of the strata where they were produced by the decomposition or distillation of organic remains. Whether this important problem involves accumulation from sources within the strata themselves, or infiltration and dissemination from outside sources, may be easily determined if all preconceived ideas are put aside and the established facts only are considered. Physical Facts Sedimentary strata are composed of alternate beds of shales, sandstones, and limestones, most of which are sufficiently close-grained to

Jan 1, 1915

Jan 1, 1967

By AIME

D R. GILLSON, who was born in Evanston, Ill., in 1895, is another one of those geologists who received his early inspiration and foundation in his science from that great teacher at Northwestern University, the late Professor U. S. Grant, and then went on to give his time and interest to Institute affairs-like those other Northwestern men, Arthur Blair, Gilbert Cady, Charlie Behre, Evan Just, Ian Campbell, Clayton Ball, and many others. After serving in the Navy in the first World War as, of all things for a geologist, a commissary officer on a transport, he went on to MIT and took his doctor&apos;s degree under Waldemar Lindgren in 1923. He even assisted in mineralogy at Harvard and thus had training under another great teacher, Charles Palache. He taught mineralogy and petrography at MIT from 1923 to 1928. After several summers of field work as an assistant in the U. S. Geological Survey, Dr. Gillson joined the staff of the du Pont company.

Jan 1, 1947

While coal was mined in New Mexico in 1860, production was on a small scale during the period considered here, and Table 77 contains all the data found. [ ]

Jan 1, 1942