Search Documents

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By Willard L. Cumings, Benjamin L. Miller

The Camaguey brown iron-ore deposit covers the top of Sari Felipe hill, the nearest point of which lies 14 miles NW. of the city of Camaguey. While there are several low flat-topped hills in the vicinity covered with a more or less continuous mantle of brown iron-ore, the deposit of San Felipe hill is the only one of any size and importance, and the name " San Belipe district" is proposed for the region. The deposit extends in a NW-SE. direction for a distance of about 10 miles, with an average width of 5 miles. The location is shown in Fig. 1, a sketch-map of the eastern part of Cuba. Fig. 2 is a map of the San Felipe district. 2. Description. The district is mentioned by Spencer,&apos; who says: " The Cubitas iron-ore fields are situated from 12 to 15 miles north of Camagueg City, in the province of Camagueg.....Within an area measuring roughly 10 miles east and west and 4 miles north and south, there are several flat-topped mesas rising 300 to 400 ft. above the level of an almost featureless plain which extends for many miles in all directions except toward the north." With the exception of the discrepancy in his statements .as to the distance from Camaguey and the area of the hill, which is over 50 sq. miles, his description is a very good one. Kemp2 has the following to say of ores in Camaguey Province:

Jan 1, 1912

By R. Steinitz, L. Seigle, R. Resnick

THE rates of growth of the carbide phases MC and M2C in the Ta-C and Cb-C systems have been measured at various temperatures and the results used to estimate the rate of carbon diffusion within the inter metallic phases. Sheets of high-purity tantalum (50 ppm Cb, <25 ppm Ti, 10 ppm Fe, 5 ppm Cr, <50 ppm Mo, W, and all other metals, 15-75 ppm O2, 10-30 ppm N2, and 10-30 ppm C) approximately 1/4 by 1/2 by 0.020 in. were heated to temperatures between 1800" and 2700°C in a carbon resistor furnace under an atmosphere of argon plus sufficient methane to maintain an excess of carbon at the sample surface. The thicknesses of the carbide layers, illustrated in Fig. 1, were measured with a filar micrometer and plotted logarithmically as a function of time. Fig. 2 is a typical plot for the TaC phase. The points may be represented within experimental error by lines with slope equal to 1/2; therefore the growth of the layers may be described by the usual expression X = kt1/2, where X is the layer thickness, t is the time, and k is a temperature-dependent constant. From these data and compositions at the phase boundaries, it is possible to estimate values for the diffusion coefficients of carbon in each phase, assuming that layer growth occurs by carbon diffusion alone, and that the dif-fusivity is not a function of composition within each

Jan 1, 1965

By Ben L. Seegmiller

Introduction The profitability of an open pit operation depends to a large extent on the use of the steepest pit slopes possible, provided they do not fail during the life of the mine Optimum pit slopes can be designed by using rock mechanics technology. Such technology includes gathering and analyzing pertinent data prior to pit design, rigorous application of rock mechanics principles during the design process, remedial actions to improve slope stability, and monitoring slopes during the life of the mine. Ignoring rock mechanics technology in pit design may place the entire mining enter- prise in jeopardy Disruption of mining operations and safety hazards caused by slope instability can be severe. A classic case in point is the major slope failure (Seegmiller, 1972) that occurred at a southwestern US copper mining operation in 1970-1971 Minor slope stability problems initially amounted to no more than a nuisance, but in time, the unstable zones became larger, causing greater disruption of production and threatening safety Mining at or near the slide toe had continued throughout the period of slope failure, aggravating the already unstable condition The original plan for this pit called for mining the overall pit slope to 37.5" Mine operators were forced to lessen the back- slope angle in the hope that the failing rock mass would stabilize. However, stabilization did not take place, and when mining in the area of failure was completed, the overall slope had been reduced to approximately 27" Mining had been successful in removing only a small portion of the ore body at a high stripping ratio.

Jan 1, 1979

By J. D. Davis, A. C. Fieldner

The older coal chemist had a much simpler conception of coal than we have today. To him coal was a mineral composed essentially of carbon, hydrogen, oxygen, nitrogen, sulfur, ash, and water, in various proportions. His studies on the constitution of coal were directed along the conventional lines of proximate and ultimate chemical analyses and making deductions from these data without any real appreciation of the fact that coal is a conglomerate of various chemical compounds, including many of the most complex structures known to organic chemistry. The view of the modern coal chemist is well expressed by Franz Fischer,&apos; who says that while proximate and ultimate analyses are important both from the scientific and technical point of view, they tell the chemist no more concerning the number and kinds of chemical compounds that constitute coal than the reader would learn of the contents of a book if told that the printed contents consisted of 15 per cent. of the letter "e," 5 per cent. of the letter "n," 1 per cent. of the letter"g," 4 per cent. of the letter "b," etc. As the reader must have the grouping of letters into words and words into sentences, so the chemist must have the grouping of atoms into molecules and the proportion of each molecular compound in the coal aggregate before he acquires an adequate knowledge of the constitution of coal. Modern investigators2 are laying the foundation of a new chemistry of coal based on the biochemistry of plants and the chemical changes involved in processes of fermentation and decay. As

Jan 1, 1925

By William Campbell

In the olden days the making of alloys was an art, and the secrete of the craft were jealously guarded. To-day it has become a science, though the old ideas in regard to the secrets and formulæ are dying hard. Modern progress may be attributed to scientific research and testing of materials, and the substitution of chemical analytical control for " cook-book " methods. We know to-day a great deal about the constitution of alloys, the reasons of the change in structure and physical properties by heat and mechanical treatment; and this new knowledge is due for the most part to the physical chemist and metallographist, who have shown us that alloys are simply solutions, and as such obey definite laws. The application of the theories of solutions and of the phase rule tells us what ought to happen when our alloys are in a state of equilibrium. The working-out of the temperature-composition diagram (thermal diagram) for numerous alloys has thrown a light on the structure and constitution which has dispelled most of the darkness in which we labored before the advent of metallography. The work began with the determination of the freezing-point curves, and here the research of Le Chatelier,&apos; Gautier,2 Roberts-Austen,3 and the other pioneers broke the ground. Next the physical chemists, Tammann,4 Rooseboom,5 Bancroft,6 and their colleagues, showed us the complete thermal diagram and its meaning. Then the researches of Heycock and Neville7 on the Cu-Sn series and of Shepherd 8 on the

Jan 1, 1913

By R. S. Dean

ALTHOUGH it is obvious that in any flotation process we must have a froth, in recent years the development of collecting reagents has caused the possibilities of better frothing agents to be overlooked. Some investigators have even gone so far as to say that the number of satis-factory frothing agents was sufficient. A little consideration will show, however, that the reagents available in the past were far from ideal frothers. The properties of an ideal frother for flotation work may be set down as follows: 1. It. must form in low concentrations a copious but not too persist-ent froth. 2. It must be insensitive to hydrogen-ion concentration of the pulp; that is, it must froth equally well in an acid or alkaline medium. 3. It must be insensitive to salts, even in high concentration. 4. It must be absolutely noncollecting to both sulfides and nonsulfides. 5. Its frothing properties must not be affected by collecting reagents, including soap, the most generally used nonsulfide collector. 6. It must readily emulsify and disperse any insoluble collecting agent that is likely to be used. Clearly the existing frothers do not qualify. Pine oil, for example, is an acceptable frother for many purposes but if used in soap flotation a delicate balance between pine oil and soap must be struck because, as pointed out by Coghill1, these two reagents are incompatible in certain concentrations. The objections to soap itself as a frother are obvious, and the cresols and their substitution products all have some collecting Dower and very little emulsifying power.

Jan 1, 1935

By A. F. Crawley

THIS paper describes part of a series of density measurements on low melting point metals being undertaken at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This program has received support from the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Examples of the type of work being done have already been given in earlier papers&apos; , which deal with the densities of lead, tin, and some of their alloys. Densities were measured using a graphite pyc-nometer by a technique which has already been described." The cadmium and indium, supplied by the Consolidated Mining and Smelting Co. of Canada were of 99.999 pct purity. Density determinations on indium, as for lead and tin,1,2 were made under a vacuum of about 5 x 10-6 torr because the oxidation and vaporization characteristics of the metal do not create experimental difficulties. This contrasts markedly with cadmium which, even at the relatively low temperatures of our experiments, has a high vapor pressure and a strong oxidation potential. To suppress the harmful effects of these properties, determinations on cadmium were made with success under an atmosphere of argon, the technique having been previously established in this laboratory for measurements on zinc.3 The densities of cadmium and indium are listed in Table I and plotted in Figs. 1 and 2. From the graphs, it is readily observed that the densities of both metals vary linearly with temperature. This relationship expressed mathematically is of the form:

Jan 1, 1969

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time. &apos;

Jan 5, 1916

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time.

Jan 5, 1916

By Edward C. Morse

The metallurgical history of Republic has been completely reviewed in a paper presented at a previous meeting of the Spokane Local Section by Professor Thomson;&apos; therefore, the present paper will be confined to matters directly pertaining to the San Poil mill: When I came to Republic last fall to look over the situation there was a plant in operation successfully treating the tailings from one of the earlier mills in the camp. I refer to the mill of the Rathfon Reduction Co. This mill was operating in accordance with modern cyaniding practice, and I was given to understand that the work was very satisfactory and profitable, else it would not have been continued as long as it was. At that time I obtained much metallurgical information of value from Harry W. Newton, Superintendent of the mill of the North Washington Power & Reduction Co. I took a number of samples from the San Poil mine, with the view of determining if Mr. Newton&apos;s experience with the ores from the other mines applied to the San Poil ores. I made a large number of tests under a variety of conditions, and found that it was possible to extract as high as 98 per cent, of the values from San Poil ore by the laboratory-tests when the ore was pulverized to 200-mesh and treated with a solution of a strength of 5 Ib. of KCN to the ton. A fairly strong solution was required because of the proportion of silver in the ore, which makes it, from a metallurgical point of view, practically

Jan 1, 1913

By Norman Patton

THE subject assigned is so broad that thorough discussion is well-night impossible within the space allotted, and further, few specific data are available upon which to predicate conclusions concerning the efficiency of present methods of distributing anthracite. This paper treats briefly the various agencies through which both primary and secondary distribution are effected, the methods of transportation and the general interrelation of production, demand, inventories and price. AVENUES OF DISTRIBUTION "Three distinct types of primary distribution are common in the marketing of anthracite. First, though not most important, is the sale by the producer, or operator, direct to the consumer. These sales, other than to employees and the local trade, are generally confined to steam sizes for industrial uses, and are consigned to the sidings or docks of the consumer. Sales of this type often are so closely priced to compete with oil and bituminous that the addition of even a small dealer&apos;s margin is sufficient to increase the cost to the point where the business might be lost. Second, the operator sells to a wholesaler or broker for subsequent resale, either to a retail dealer for clearance through his yard or direct to large consumers. Usually this method of distribution is employed by the smaller operators, who do not find it economically feasible to maintain extensive sales organizations. In most instances, the wholesaler retains some 5 per cent for his services, paid, of course, by the producing company whose anthracite he handles. He may, and frequently does, handle the output of several different companies, suited to the varying needs of the

Jan 1, 1935

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By C. B. Jordan

LAVES and Wallbaum&apos; have described TiRu and TiOs as having the same structure as TiFe; they had previously described the latter compound as having the CsCl structure. On the other hand, a careful investigation of the structure of TiFe by Duwez and Taylor- ailed to reveal the ordered CsCl structure, finding instead a random arrangement of titanium and iron atoms on the points of a body-centered-cubic space lattice. Consequently, it is not clear whether Laves and Wallbaum proposed the ordered or the disordered structure for TiRu and TiOs. In order to settle this question as to the structural type and to obtain values of the lattice para- meters (thereby completely determining the structures), the present investigation was undertaken. Samples having the compositions TiRu and TiOs were weighed out accurately from iodide titanium supplied by the New Jersey Zinc Co., ruthenium powder from Goldsmith Brothers Smelting & Refining Co., and osmium powder from Wildberg Brothers Smelting & Refining Co. No analysis was made of any of these metals. According to the respective analyses of the suppliers, total impurities amount to less than 0.03 pct in the titanium and to less than 0.5 pct in the osmium. The purity of the ruthenium is not known. The alloys were prepared by arc melting in a furnace of the type described by Schramm, Gordon, and Kaufmann.9 pecimens for X-ray diffraction were obtained by crushing the ingots and passing the resulting powders through a 200 mesh screen. Diffraction patterns were made with a powder

Jan 1, 1956

By Robert Mehl

THE mechanical behavior of metals and alloys is presumably conditioned by two factors; namely, the crystalline symmetry and the interatomic forces. Considerable attention has been given to the first of these factors through the recent advances in X-ray .technique. It is the purpose of the present paper to call attention to the importance of the second of these factors, to point out promising methods of investigation, and to present some pertinent data. Plastic deformation takes place by-slip along atomic planes.1 This slip may be inhibited in a number of ways: by the interatomic forces of cohesion which bind the atoms rigidly in a lattice structure, which in pure metals is usually of high symmetry; by lattice distortion caused by solid ,solution formation or by mechanical strain; by the intercrystalline boundaries where slip is restrained by the non-registration of the atom planes in adjacent crystallites;2 and by the presence of small hard particles which serve to "key" the slip along the atom planes.3 In pure metals, and perhaps also in solid solutions, the atom planes, of easiest slip are those exhibiting the greatest density of atomic population and the greatest interplanar distance4 and apparently can now be predicted from the analysis of the lattices. Concerning the interatornic forces, which resist this slip by holding the atoms firmly together, little is known. Most textbooks on physical metallurgy, following the work of Bot-tone,5 correlate the hardness of the pure metals with the atomic volume;.

Jan 1, 1928

By J. J. Taber, W. K. Meyer

Experiments on consolidated sandstones have shown that a variety of conditions are responsible for the wide range of behavior observed when oil and water are displaced simultaneously by a solvent which is miscible with both. The type of displacement is influenced most strongly by the relation between the plait point of the ternary phase diagram and the composition path followed by the system as it achieves mis-cibility. Neglecting viscosity, the displacement becomes less efficient as the distance between the composition path and plait point is increased in either direction so that a very wide spectrum of displacements is possible with different alcohol, oil and brine systems. It is possible by choosing various composition paths as miscibility is achieved to exercise some control over the actual displacement mechanism. Control over the composition path is exercised by adding oil or water in specific amounts to the alcohol prior to its injection into the porous medium. This technique apparently makes it possible to obtain piston-like displacements with systems which are usually characterized by the efficient displacement of only one of the two phases i.e., either oil or water, while the other phase lags behind. However, the simultaneous displacement of oil and water is not as efficient as other miscible displacements at a similar mobility ratio. The evidence indicates that both oil and water "leak" into the alcohol "piston" in compensating amounts. With oils of low viscosities the displacement is inefficient because the low oil saturation in the stabilized bank causes oil to be trapped by water before miscibility is attained. INTRODUCTION The simultaneous displacement of oil and water by solvents such as alcohol has been investigated in the laboratory and in the field. The laboratorv workers investigating all-liquid miscible systems have recognized the great importance that the nature of the traingular phase diagram exerts on the efficiency of the miscible displacement. Gatlin and Slobod pointed out that displacement efficiency will be improved if miscibility can be retained for long periods and that this behavior tends to be followed if the applicable phase diagrams have very low binodal curves. In their unconsolidated sand tests the alcohol was considered an ideal miscible piston displacing both oil and water phases. Later workers have pointed out that an important feature of the phase diagram as far as oil recovery is concerned is the location of the plait point. This is particularly true in the case of consolidated Sandstone.3 Since the original discussion of this effect, the importance of plait-point location has been confirmed and discussed by other author The early workers394 recognized that the position of the plait point could be altered by changing the oil or the alcohol used in an experiment. In addition, recent work has demonstrated that the plait point can be shifted by altering the nature and concentration of dissolved salts in the aqueous phase. However, the entire scope of the relationship between displacement and plait point has not been discussed previously and a technique for changing the composition path as miscibility is achieved in a particular ternary system, i.e., oil, water and solvent, has not been demonstrated. * The importance of oil viscosity on the efficiency of oil displacement by alcohol has not previously been observed, probably because the range of viscosities used in earlier experiments was too restricted. It is the object of this paper to describe the relationships between the ternary phase diagram, fluid properties and the displacement achieved. A technique for controlling the nature of the displacement is also presented. THEORY AND DEFINITIONS PISTON-LIKE THEORY The theory of alcohol flooding has been discussed in some detail.2-4 The concept was advanced that

Jan 1, 1965

By Eduardo J. Chibas

Location.—The principal manganese-deposits of the Department of Panama, Republic of Colombia, are located almost clue south of Viento Frio, a native village bordering on the Caribbean Sea, and about 45 miles northeast of Colon (Aspinwall). The mining-claims are the Viento Frio, the Carrano, the Nispero, and the Soledad. Each property is to the south of the preceding one in the order mentioned. The first one is about one mile from the coast, and the most southerly boundary of the Soledad is about five miles in a straight line from the same coast-line. I shall confine my remarks to the four properties mentioned and to La Guaca, west of the Carrano, because these are the only ones where mining has so far been done to more or less extent. Manganese has also been found, however, in the neighborhood of these deposits, and a large area adjoining them has been divided into sections and " denounced " as mining-claims. The relative position of the manganese-deposits and Nombre de Dios, the present terminal of the railroad and shipping-port, as well as Viento Frio and the adjacent coast, can

Jan 1, 1898

By F. W. Jessen, James N. Howell

INTRODUCTION The determination of cloud points has to date been limited to rather transparent oils, visual observation of the formation of a solid phase being the criterion for the standard ASTM D 97-47 method. The need for a quiclc and simple method for determining cloud points under dynamic conditions for opaque crude oils became necessary in a study of fundamental aspects of paraffin deposition from crude oils. PREVIOUS WORK The determination of cloud points in opaque oils by viscosity temperature curves is fairly new, Young&apos; described a method employing the capillary tube principle. No information exists relative to the determination of cloud points of crude or refined oils under dynamic conditions. Shock&apos; noticed that deposition of paraffin from crude oils took place at temperatures at or below the temperature at which a sharp inflection point occurred in the viscosity-temperature curve. This observation indicates a possible correlation between this temperature and the cloud point of the crude oil. Reistle and Vietti1 have reported that when crude oils containing small amounts of asphaltic materials were heated to temperatures sufficiently high to solubilize these materials and immediately cooled the pour point of the crude oil was lowered as much as 70°F. Sachanen\ asribes this effect to the action of colloidal asphaltenes in preventing the formation of the crystalline structure necessary to maintain the oil in a rigid state. At high temperatures, asphaltenes are peptized, and the paraffin crystals formed at these temperatures adsorb the colloidal asphaltenes on their surface thereby hindering further growth of the crystals. Reistle" found, however, that such heating and cooling of crude oils had no effect upon the cloud points. This latter work dealt with a crude oil of fixed composition, and the question immediately arises as to the effect of varying the concentration of asphaltic materials on the cloud point. APPARATUS AND PROCEDURE All viscosity measurements were made with a Bendix Ultra-Viscoson. The Bendix Ultra-Viscoson, which consists of a vibrating probe and an electronic computer. measures viscosity by exciting a thin alloy steel blade on the end of a probe by short electrical pulses in damped oscillation at 28 kilocycles. The blade vibrates longitudinally with an amplilude of less than 55 micron or 20 millionths of an inch. Energy to protlucc this excitation is generated in he computer and transferred to the probe through the connecting cable. The oscillating blade is magnetostric-tive, i.e., it is capable of transforming electrical energy to mechanical energy in the ultrasonic range. Ultrasonic waves are produced in the material surrounding the blade by the oscillating motion of the blade causing layers of the material to slip back and forth over one another at a known frequency. The electronic computer calculates the energy required to produce the sliding motion which is in turn proportional to the viscosity of the material. Actual values of viscosity times density (centi-poise X grams/cc) are indicated on the computer and a continuous D-C signal is provided which is fed into a type 153 Electronic Recorder (manufactured by Brown Instruments Div. of Minneapolis-Honeywell Regulator Co.) The liquid sample container was fabricated from a Lucite cylinder and jacketed by a Luicite water bath. Early experiments using glass and steel sample containers were not satisfactory. since the Ultra-Viscoson was apparently affected by the alterzltion of the magnetic fields surrounding the probe by stresses set LIP in the glass and steel as it cooled. The procedure for determining viscosity-temperature curves was relatively simple. The temperature ot the sample was raised sufficiently high to solubilize all paraffin and asphalts present. After heating, the oil sample was immediately transferred

Jan 1, 1957

By C. L. Sainsbury

Lode and placer tin deposits of the western Seward Peninsula, Alaska, have produced more than 2200 tons of metallic tin and constitute the only known domestic deposits of economic grade and size. The lode deposits consist of quartz-topaz greisens containing cassiterite and wolframite as well as numerous base-metal sulfide minerals, and most are in or near altered biotite-granite that forms isolated stocks or in rhyolitic dikes near granite. Within the main lode-producing area in the central York Mountains, nonpegmatite beryllium deposits, consisting principally of fluorite, chrysoberyl, diaspore, tourmaline, and white mica, with minor euclase, bertrandite, phenakite, hematite, and todorokite, are distributed zonally around the tin deposits and locally are transitional with them. All the known beryllium deposits are replacement lodes in carbonate rocks. In the area discussed, both tin and beryllium deposits are localized in a structural belt striking N70° to N85°E across the central York Mountains. The belt is characterized by numerous normal faults, which cut extensive thrust sheets, and by dikes of rhyolite, rhyolite porphyry, and lamprophyre that were injected along the faults. Ore deposits are localized where the dikes intrude brecciated rocks beneath thrusts and, although complex in detail, form tabular lodes that tend to lie along the thrusts. The granites contain abnormal amounts of tin, beryllium, lithium, and boron, and the tin and beryllium lodes are believed to be genetically associated with these enriched granites

Jan 1, 1968

By N. V. Melnikov, L. N. Marchenko

The latest theoretical and experimental study of physical processes initiated by explosions in solid media have made it possible to obtain a deeper insight into the mechanism of the energy transfer to ambient rock from char es of explosives interspersed with various air gaps. As shown in (17, high explosive action causes excessive fragmentation of medium in the vicinity of the charge, while expansion of the process into the massif is negligible. A theoretical outline of a more rational application of explosion energy was given with a view of obtaining more uniform fragmentation of rock convenient for loading and transportation. The proposed idea proven by experimental study consisted of the possibility of explosion control based on redistribution of explosion energy. Practical realization of the above idea was proposed (1) involving charges with air gaps for rock fragmentation. Since the Rolla Symposium on Mining Research (USA, 1961) (2), borehole charges with air gaps have become common practice. This method of rock blasting is applied in open cast and underground mines working the hardest and viscous, hard, medium hard and soft rocks (ore, quartzites, granites, 1 imes tones, sandstones, coals, etc.) as well as at enterprises for extraction of building materials and raw chemical minerals of any strength. Application of charges with air gaps results in an increase of the degree and uniformity of fragmentation (up to 94 percent of the blasted rock mass consists of fragments not exceeding 400 mm), the average fragment size decreases by 1.5-2 times and the amount of lumps is reduced by 2-10 times (in some cases there are no lumps at all ). Besides, the amount of operation for filling boreholes with tamping material is reduced, the specific consumption of explosives

Jan 1, 1971