Search Documents

By J. J. Calaman, D. H. Fleming

DURING 1950 the jet-piercing process was used commercially in the piercing of primary blast-holes in magnetic taconite at the preliminary taconite plant of .the Erie Mining Co., Aurora, Minn. The Erie Mining Co. purchased a jet-piercing machine and associated equipment in 1949, and the machine has been in operation since its installation in the summer of that year. An overall view of the pit with the JPM-1 jet-piercing machine in operation is shown in Fig. 1. During three months of 1949 and continuously since February 1950, production piercing took place under all pit conditions. By the end of October 1950, a total of 15,000 linear ft of hole had been pierced in an open pit handling an average of 1200 to 1800 tons of crude a day in one 8-hr shift. While it is recognized that this output does not approach the millions of tons a year planned for the developing Minnesota taconite projects, the machine as a unit has been operating under conditions probably more adverse than those that eventually will be encountered in the large operations. This pilot operation has permitted evaluation of the piercing problem in the full-scale taconite plant. This paper describes jet-piercing process funda- mentals, important features of the latest jet-piercing burners and machine, actual piercing results obtained, and new developments that give promise of materially increasing overall process efficiency. To produce the blasthole, jet-piercing utilizes thermal energy, as contrasted with the application of mechanical energy in churn drills and jackham-mers. The heart of the process may be termed a tailored flame produced by a rocket-type burner, thermodynamically similar in every respect to that of the giant rockets being developed for military purposes. The heat release in the combustion chamber of the burner is about 50x10' Btu per cu ft per hr as compared with 5x10' for most modern steam generators.* Combustion of liquid petroleum fuels (kerosine, diesel oil, or No. 2 fuel oil) with gaseous oxygen in the burner chamber at pressures of 100 to 200 psi results in temperatures of about 4300°F. Expansion of the hot combustion gases through divergent nozzles produces high-temperature supersonic jets having measured velocities of about 6000 fps. Impinging the flame jets on rock causes a thin surface layer to expand and break away from the base as a result of the thermally induced stresses. This spalling action is aided further in chert and quartzite by the 0.82 pct volume change resulting from the 6 to p quartz inversion at 1066"F.t The dynamic action of the jets whisks the spalled rock

Jan 1, 1952

By Gordon H. Geiger, J. Bruce Wagner

Electrical conductavity and therrnoelectvic nzeasuretnents on synthetic hematite slabs with 0.01 to 0.90 at. pet Ti and with 0.30 at. pet Ca were made. Additions of titanium and of calcium both increased the electronic conductivity with titanium yielding greater n-type behavior and calciurn p-type behavior. Reduction studies of hematite to magnetite in CO-CO2 atmospheres between 600° and 900°C initially exhibited linear kinetics. These linear rates were increased by additions of titanium and decreased by calcium. IN recent years many studies have been reported in the literature on the kinetics of the reduction of hematite and magnetite to iron. In addition, Hansen and Josephl and Schenck and Schultz2 have reported studies on the reduction of hematite to magnetite, the first step in total reduction to iron. In order to evaluate the results of the studies of over-all reduction in terms of the actual mechanism of the reaction and to define further the important factors in the rate- controlling mechanism of the magnetic roasting reaction, the following experiments were undertaken. Specimens of undoped hematite and hematite containing titanium or calcium in solution as doping agents were reduced to magnetite in CO-CO2 mixtures. In addition, electrical-conductivity measurements were correlated with the reduction kinetics using concepts of defect solid-state chemistry. EXPERIMENTAL Fisher certified Fe2O3 powder was used to make specimens for both the electrical and kinetic studies (see Table I for analysis). Doping with titanium and calcium was accomplished by adding TiO2 and CaO powders to the Fe2O3 powder. The powders were mixed in a Waring blender for minimum times of 1/2 hr. Satisfactory blending was achieved based on comparison of analyses of individual specimens af- ter reduction. The specimens were formed in a steel die using opposed punches with a rectangular opening 10.0 by 40.0 mm. The Fe2O3-TiO, platelets were pressed cold at 16,000 psi. They were sintered for approximately 16 hr at 1075°C in air, in accordance with information in the literature3, 4 on the time and temperature needed to obtain solution of the titanium in the hematite. The Fe2O3-CaO mixtures were first cold-pressed at 20,000 psi and sintered for 3 hr at 1225°C to insure solution of CaO. This material was then ground to -325 mesh in a 6-in. ball mill and the resulting powder was used to make platelets in the same manner as above. The sintered platelets were usually between 1/16 and 1/8 in. thick. They were ground on a carborundum wheel and polished on 2/0 paper. Typical dimensions of the kinetic-study specimens were 1.6 by 0.8 by 0.05 cm, and a typical weight was 0.3 g. Conductivity and thermoelectric specimens were approximately the same size, but were subjected to further sintering in order to ensure maximum densification. Finally, all specimens were measured to the nearest 0.0005 in. and weighed on a Mettler H-15 balance to the nearest 0.0001 g and the density calculated. The average density of the specimens used for the reduction studies was 4.87 g per cc, or 7.1 pet total porosity. The standard deviation ranged from 0.14 to 0.063 g per cc within a composition group. In the present study, the apparent surface area as measured with a micrometer was taken as the true surface area. The chemical analyses for calcium and for titanium within a group showed maximum variations of 50.04 pet from the average values used in Figs. 9 and 11. In order to suspend the specimen from the balance for the kinetic studies, a hole, 0.03 in. in

Jan 1, 1965

By R. G. Knickerbocker

A STURDY and consistent expansion of the metal industry occurred in 1947 exemplified by an increase of approximately 30 per cent in steel consumption over 1946. For this major reason, ferroalloy metals have seen their most useful and important peace-time year. The current domestic rate of consumption of high-grade ferroalloy ores, together with added consumption of new foreign producers as well as for eign nationals' restrictions on high-grade exports, makes very evident the increasing difficulties of obtaining sufficient high-grade ores. This accentuates the need for new and less expensive methods of production of ferro-alloy metals of higher purity from lower-grade domestic resources. As an important factor in preparedness, procurement of these high-grade, -critical ferroalloy minerals and metals for our nation's stock piles is a most important task. Also, this stock-piling can be the means of supplying incentive for the industrial development of the new metallurgical processes and plants necessary for the recovery of ferroalloy metals from our domestic low-grade deposits.

Jan 1, 1948

By M. Gensamer

A RECENT paper1 described, by means of stereographic pole figures, the preferred orientations produced by cold-rolling low-carbon steel of automobile-body grade. It was found that the surface of the sheet exhibited a deformation texture significantly different from the texture possessed by the inside of the sheet. Efforts to produce the surface texture by buffing a sample exhibiting the normal or inside texture, using a copper lap, have not been successful. In view of the data collected, by Kurdjumow and Sachs2, it was suggested that the surface texture might be the result of partial recrystallization of the normal or inside texture. The recrystallization texture of cold-rolled mild steel was studied by Goss3, but he did not use the pole-figure method, so that his conclusions were in need of verification. For these reasons the work reported in the present paper was undertaken. It had two objectives: (1) to study the general behavior of cold-rolled mild steel on recrystallization below the critical temperature A,, and (2) to attempt experimentally a demon-stration of the genesis suggested above for the surface texture in cold-rolled steel. The material was that used by Gensamer and Mehl, cold-rolled to 97.5 per cent reduction in thickness. Fig. 1 is an X-ray pinhole photo-gram of this material, taken with the beam transmitted perpendicular to the plane of the sheet, using a molybdenum target at 35 kv. with no filter. It is typical of the inside texture, but in it the deformation texture is better developed than in the samples that showed a well developed difference between the inside and surface samples. Specimens from this sheet, which was 0.005 in. thick, were annealed for 5 min. at various temperatures in a lead bath. After about 0.0005 in. had been etched from both surfaces, X-ray photograms were prepared, using the technique described in the earlier paper'.

Jan 1, 1936

By J. E. Tobey

THERE are a lot of good things about this great industry of ours. Let us stop commiserating and consider some of the things that are right in this business. Coal is number one in the basic material industries. Our civilization owes more to it than to any other basic commodity. We are literally immersed in the benefactions of coal. In cur man-made world it is indispensable and we are constantly surrounded by objects, materials, and services which owe their existence to coal. Practically all the important materials, such as iron, steel, brick, cement, lime, rubber, glass, cotton, and wood have felt its magic touch.

Jan 1, 1939

By John Dodd

This paper reviews advances in the technology of abrasion resistant iron and steels, which could help combat abrasion and wear in mining operations. With the recent progress in high chromium alloy iron development, high temperature heat treatment of massive castings can be eliminated, aloy cost reduced, and cracking problems avoided. Data on erosion-corrosion resistance of these irons; trends in the development of improved cast steels; and factors influencing toughness and abrasion resistance of manganese steels are all considered. The 7% Mn. 1% Mo manganese steels are shown to combine toughness and abrasion resistance, and composite castings are a means of combating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1982

By A. C. Fieldner

DURING 1939, 286 by-product coke ovens were completed and put into operation. These included 140 Witputte ovens for the Carnegie-Illinois Steel Corp., at Gary, Ind.; 61 Koppers-Becker ovens for the Ford Motor Co., at River Rouge, Mich.; 65 Semet-Sotvay ovens for the Great Lakes Steel Corp., Zug Island, River Rouge, Mich.; and 20 Curran-Knowtes ovens for the Midwest-Radiant Corp. plant at Mitlstadt, Ill. The Millstadt plant is unique in carbonizing a washed coat containing 3.50 per cent sulphur. The gas contains approximately 2500 grains sulphur per 100 cu. ft.; this is successfully removed with sodium carbonate solution by the Seaboard liquid purification process. The coke is intended primarily for use as a smokeless domestic fuel in the city of St. Louis.

Jan 1, 1941

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By Oliver M. W. Sprague

THIS gold problem is full of complications and can hardly be handled adequately or comprehensively in any short period of time. Perhaps I might begin by mentioning a few aspects of the subject about which I suppose there will be no disagreement. The first of these is that we already have a stock of monetary gold in the United States far in excess of what is needed to support any desirable increase in the present volume of currency and credit. The second is that this already superabundant gold stock is certain to be considerably enlarged during the course of the war, and presumably during the months of readjustment following its conclusion. Some billions of additional gold, we may reasonably presume, will come into the country during these next few years, thus increasing the aggregate monetary gold stock from the present eighteen billions to perhaps twenty- two or even twenty-five billion dollars.

Jan 1, 1940

By B. R. Coil

One executive writing on capital equipment re- placement stated: "We keep extremely close watch over repair costs and when we reach the point of uneconomical operation, we replace the machine." This, of course, is most elementary, but a very basic premise. However, it seems advisable to set forth several equally obvious principles, so that all discussion will start from the same point. The subject is intended to deal with the point of uneconomical operation due to high operating costs in general and high repair costs in particular. This is not concerned with a similar problem of high costs because of an insufficient number of machines, be they trucks, shovels, or dozers.

Oct 1, 1955

By Robert A. Bauer

This study showed that diametral point-load testing performed parallel to the bedding planes of highly anisotropic sedimentary rocks produced inconsistent results that cannot be used to accurately estimate uniaxial compressive strength. Axial point-load values from tests performed normal to bedding planes and evaluated by the T500 index produce good correlations with the uniaxial compressive strength values obtained for five different rock types. A strong correlation also existed between the moisture content and the uniaxial compressive strength of the tested lithologies. A combination of axial point-load and moisture content indices produces the best correlation with the uniaxial compressive strength test results.

Jan 1, 1984

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1944

By Howard L. Hartman

There is reason to believe that ventilation systems so far devised for use with continuous mining machines fall far short of success. This is vividly demonstrated to anyone who has observed in a continuous miner section the localized ignitions of pockets of gas and the generation of dense clouds of dust by the cutting head of the machine. The alarming frequency with which major ignitions and disasters continue to occur in modern mechanical mining and the rise in incidence of pneumoconiosis serve as reminders that our ventilation systems are far from achieving the ultimate in providing protection from either short-term explosions or long- term dust diseases, both of which take lives. Human safety is the main concern in ventilation. But in this day of high-priced labor, let us not forget human comfort, either, for this is a major factor in motivation toward high productivity. The failure or inadequacy of most mine ventilation systems in providing the kind of working conditions at the face that are conducive to productive as well as safe operation is an indictment of our environ- mental control program in mining generally.

Jan 3, 1962

It has been suggested that it would be a desirable feature in connection with the Chicago meeting of the, Institute in September to arrange for a return trip for the fuel men through the coal fields of Illinois, Ohio and Pennsylvania, stopping at various points and possibly touching also Kentucky. Perhaps the petroleum men would be interested in a similar trip and might join them stopping off at different points to visit these oil fields. If the members who would-be interested in such a trip will advise the Secretary before the first of June, indicating their desired stopping points, steps will be taken to perfect arrangements accordingly.

Jan 5, 1919

By James Douglas

Discussion of the paper of James Douglas, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 29, May, 1909, pp. 439 to 451. JAMES DOUGLAS, New York, N. Y. (communication to the Secretary*) :-In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker's report for .1906 an explanation given by him in accounting for the small production of by-product coke. It was that the markets for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908 1 does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, lie says (p. 241): "The year 1908 was not marked by any notable gain in the construction of by-product coking plants, though some new work was done. There was a net increase of 115 in the number of completed ovens in 1908 over 1907, the totals for the two years being, respectively, 3,892 and 4,007. The additional equipment consisted of 140 Koppers regenerative ovens built at Joliet, I11., by the United States Steel Corporation, but this increase was partly offset by the dismantling of Y5 Semet Solvay ovens at Sharon, Pa., the net gain being 115 ovens. Included in the total of 4,007 completed ovens in 1908 are 152 Newton-Chambers ovens at Vintondale, Pa., but as no recovery of by-products was made at this plant in 190S, the production of coke is included with that from beehive ovens. The 56 ovens of the same type at Pocahontas, Va., have not been in practical operation since they were first. installed. In addition to these there was one other by-product plant of 120 ovens. Oat. was not operated during the year. The number of retort ovens producing coke in 1908 was 3,679, as compared with 3,811 active ovens in 1907." In describing the anomaly he says (p. 249): It has been contended that the development of the by-product coking industry would have shown more rapid progress if markets for the by-products were * Received Feb. 2, 1910. Mineral Resources of the United States for 1908, Part I1., U. S. Geological Survey (1909).

Apr 1, 1910

Abbott, Robert H., (S'42) Agricultural & Mech. College of Texas, College Sta.. Texas. Abrahamson, Guy C., (S'43) Univ. of California, Berkeley. Calif. Abrego, Alfredo, (S'43) Texas College of Mines & Metallurgy, El Paso, Texas. Ackermann, K. G., (S'43) Univ. of Alabama, University, Ala. Adamec, Lew, (S'42) Colorado School of Mines, Golden, . Colo. Adams. Charles E., (S'42) Univ. of California, Los Angeles, Calif. Adams, Charles W., (S'30) Asst. Met., Canada Foundries & Forgings Ltd., Welland, Ont., Canada. Adams, John W., (S'42) Univ. of Texas, Austin, Texas. Adams, Karl S., (S'43) Univ. of New Hampshire, Durham, N. H. Adamson, Charles R., (S'41) Univ. of Utah, Salt Lake City. Utah. Adler, A. G., (S'41) Met. Engr., Flotation Operator Helper. Utah Copper Co.. Garfield, Utah. Adler, Frank J., (S'42) Colorado School of Mines, Golden, Colo.

Jan 1, 1943

Jan 1, 1962

By Nagel, Theodore

USE of oxygen in metallurgical operations was investigated by a committee of unusually able engineers more than ten years ago. A record of their work appeared under the title "The Use of Oxygen or Oxygenated Air in Metallurgical and Allied Processes," Serial 2502, Report of Investigations, U. S. Bureau of Mines. Shortly thereafter the A.I.M.E. published "Use of Oxygenated Air in Metallurgical Operations," based on a symposium at the New York meeting, February 1, 924. Quoting from the Bureau of Mines report In view of the many recent developments in oxygen manufacture, and considering the increasing cost and decreasing quality of our raw materials, the Bureau of Mines has taken the matter of the application of oxygen or oxygenated air to the metallurgical centers for consideration and has appointed an advisory committee to study the problem.

Jan 1, 1935

By M. E. Learmont, I. Iwasaki

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1985

By W. R. Johnson, M. Hansen, John M. Parks

AS part of a research project sponsored by the Signal Corps Engineering Laboratories, which had the objective of obtaining a magnet wire of good conductivity and low temperature coefficient of resistance, a comprehensive literature survey, supplemented by experimental work, revealed that a linear relationship exists for solid-solution alloys between the electrical conductivity, K, and the temperature coefficient, a, as expressed by the equation: k = a/ß where ß is constant for the solvent metal and a - per°C. tR0 It has long been known that the electrical conductivity at a given temperature and the temperature coefficient of resistance of binary alloys are related to their constitution by the LeChatelier-Guertler rules, as illustrated by Figs. 1 and 2: Rule 1—In alloy systems consisting of a heterogeneous mixture of two phases, the electrical conductivity and temperature coefficient vary as a straight line, if the composition of the alloys is given in volume percentage, Fig. 1. Rule 2—In solid solutions, the electrical conductivity and temperature coefficient are always lower than those of the solvent metal, and usually a considerable decrease occurs with the first small percentage additions of the solute metal, Fig. 2b. If the two components form a continuous series of solid solutions, the electrical conductivity and temperature coefficient curves take the form of a U-curve, Fig. 2a. That some kind of proportionality exists between electrical conductivity and temperature coefficient of resistance is implied by the LeChatelier-Guertler rules and by study of data such as those given by Smith and Palmer,' Fig. 3. Dellinger2 in 1910 first recognized this relationship in a number of commercial copper wires, ranging in conductivity from 94 to 100.7 pct I.A.C.S. He gave the ratio of temperature coefficient to the percentage of conductivity as a constant, C = 0.003939. A year later, Lindeck observed that the linear relationship was valid for a wider range of conductivity in "various sorts of copper," and concluded that the product of resistivity and temperature coefficient was 6.78x10-5 1.5 pct. Since then, this relationship seems to have been entirely ignored. Conductivity-Temperature Coefficient Relationship If the electrical conductivity of copper solid-solution alloys with phosphorus, silicon, arsenic, antimony, aluminum, nickel, manganese, and iron is plotted against the temperature coefficient of these alloys, the diagrams in Figs. 4 and 5 are obtained. Similar data were found with copper-rich solid solutions containing magnesium, cobalt, and titanium,'" as shown in Fig. 6. In all cases, a linear relationship exists. The point representing the highest

Jan 1, 1952