Search Documents

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

Rutile – Zircon Mining on East Coast Surfing Beaches – Rutile-Zirconium Producing Companies in Australia

Jan 10, 1964

By P. O. Metz, E. L. Wiehe, J. S. Foster

BASED on their analyses of growth kinetics, ibbs' and Harris et al.' have recently proposed that the rate of subcritical graphitization of steel is controlled by the rate of diffusion of carbon in ferrite. illert has concluded that this is the rate controlling growth mechanism when the growing graphite particles are relatively large. Harris et al.' also propose that the matrix surrounding a growing graphite particle is plastically deformed to make room for the growing particle. If this plastic deformation does occur, then preferred recrystallization may be observed around the larger particles. If diffusion of carbon in ferrite is rate controlling, then a graphite particle growing in a matrix of, say, tempered martensite or pearlite, should be surrounded by a carbide depleted zone. Thus, the simple metallographic experiments reported here are sufficient to determine whether or not diffusion of carbon in ferrite is the dominant mechanism for the growth of graphite in steel. The present investigation considers graphitization in five alloys. The compositions are given in Table I. Graphitization was carried out at three temperatures: 900°K (627"C), 950°K (677"C), and 990°K ('717°C). Samples were reacted in both the martensitic and the pearlitic initial conditions. In the hypoeutectoid steels, Sets 7 and 8, .and in the hypereutectoid Fe-C binary, Set 6, graphitization was very limited after 1000 hr at temperature. In these samples graphite particles observed were less than 10 p in diam. In the hypereutectoid commercial steels, Sets 1 and 3, large graphite particles (100 p) did not appear until after 250 hr at temperature. The limited number of graphite particles observed and the range of sizes obtained prohibited measurement of growth rates in this investigation. However, in all samples showing graphitization, neithe a carbide depleted zone nor recrystallization was observed. illert's model predicts that diffusion of carbon in ferrite should become dominant for graphite particles larger than about 300 p in diam. The largest graphite particle observed in this investigation was approximately 450 p in diam. No evidence of carbide depletion was noted. Fig. 1 shows a typical graphite particle. This nodule is from an initially pearlitic sample from Set 3 after

Jan 1, 1970

Page The Cobaltchromium Binary System (paper by A. R. Elsea, A. B. \Yesterman, and G. K. Manning, Met. Tech. June, 1948, Mechanism of Precipitation in a Permanent Magnet Alloy (paper by A. H. Geisler and J. B. Newkirk, Met. Tech. Aug. 1948, Tp 2444)................................................................................................. 300 Some Effects of Applied Stresses on Precipitation Phenomena (~aper by W. L. Finlay and W. R. Hibbard, Jr., Met. Tech. Sept. 1948, Tp 2470)....................................................................................... 301 Diffusion of Carbon in Austenite with a Discontinuity in Composition (paper by L. S. Darken, Met. Tech. Sept. 1948, TP 2443) 304 An Electron Diffraction Study of Oxide Films Formed on Nickelchromium Alloys (paper by J. W. Hickman and E. A. Gul- bramen, Met. Tech. June 1948, Tp 2372)..................................................................... 305 An Electron Diffraction Study of Oxide Films Formed on Copper-nickel Alloys at Elevated Temperatures (paper by J. W. Hickman and E. A. Gulbransen, Met. Tech. June 1948, TP 2391)................................................ 307 Decarburization of Chrome Nickel Alloys by Their Surface Oxides in High Vacua and at Elevated Temperatures (paper by E. A. Gulbransen, W. S. Wysong, and K. Andrew, Met. Tech. Sept. 1948, TP 2438)................................ 307 Fractographic Study of Cast Molybdenum (paper by C. A. Zapffe, F. K. Landgraf and C. 0. Worden, Met. Tech. Aug. 1948, TP 2421)................................................................................................. 308 Effect of Composition on Grain Growth in Aluminum-magnesium Solid Solutions (paper by L. J. Demer and P. A. Beck. Met. Tech. June 1948, TP 2374)............................................................................. 309 Effect of a Dispersed Phase on Grain Growth in Al-Mn Alloys (paper by P. A. Beck, M. L. Holzworth and P. Sperry, Met. Tech. Sept. 1948, TP 2475)................................................................................. 310 Statistical Rate Theory of Metals—Mechanism of Flow and Application to Tensile Properties (paper by J. W. Fredrickson and H. Eyring, Met. Tech. Aug. 1948, TP 2423)............................................................... 315 Nucleation of Slip Bands (paper by J. G. Leschen, R. P. Carreker, and J. H. Hollomon, Met. Tech. Sept. 1948, TP 2476) and.. 318 Transient Plastic Deformation (paper by R. P. Carreker, J. G. Leschen, and J. D. Lubahn, Met. Tech. Sept. 1948, TP 2477).. 318 Plastic Deformation of Large Grained Copper Specimens (paper by W. R. Hibbard, Jr., Met. Tech. Sept. 1948, TP 2469). ... 323 Plastic Flow in Anisotropic Sheet Steel (paper by L. R. Jackson, K. F. Smith, and W. T. Lankford, Met. Tech. Aug. 1948, TP 2440)................................................................................................. 323 The Effect of Thermal-mechanical History on the Strain Hardening of Metals (paper by J. E. Dorn, A. Goldberg, and T. E. Tietz, Met. Tech. Sept. l948, TP 2445)....................................................................... 325 The Room and Elevated Temperature Properties of Some Sand Cast Magnesium-base Alloys Containing Zinc (paper by T. E. Leontis, Met. Tech. June 1948, TP 2371)..............................................................., 327 The Low Temperature Properties of Tin and Tin-lead Alloys (paper by H. S. Kalish and F. J. Dunkerley, Met. Tech. Sept. 1948, TP 2442)............................................................................................335 Thermal and Electrical Properties of Ductile Titanium (paper by E. S. Greiner and W. C. Ellis, Met. Tech. Sept. 1948, TP 2466).................................................................................................... 335 Property Changes during Aging (paper by A. H. Geisler, Met. Tech. Aug. 1948, TP 2436)............................... 337 Factors Affecting the Tensile Notch Sensitivity of Magnesium Alloy Extrusions (paper by I. Cornet, Met. Tech. Aug. 1948, TP 2419)................................................................................................. 338 Effect of Grain Size on Tensile Strength, Elongation and Endurance Limit of Deep Drawing Brass (paper by H. L. Walker and W. J. Craig, Met. Tech. Sept. 1948, TP 2478)............................................................. 339 A Copper-base Alloy Containing Iron as a High-strength, Highconductivity Wire Material (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Met. Tech. Aug. 1948, TP 2422).............................................. 340 A High Strength-High Conductivity Copper-silver Alloy Wire (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Mel. Tech. June 1948, TP 2366)...................................................................... 340 The Effect of Chronlium on the Ma Point (paper by J. B. Bassett and E. S. Rowland, Met. Tech. Aug. 1948, TP 2417.... 341 The Kappa Eutectoid Transformation in the Copper-silicon System (paper by W. R. Hibbard, Jr., G. H. Eichelman, Jr., and W. P. Saunders, Met. Tech. Sept. 1948, TP 2441).............................................................. 343 Stabilization of the Ausknite-martensite Transformation (paper by W. R. Harris, Jr. and M. Cohen, Met. Tech. Sept. 1948, TP 2446)................................................................................................ 344 Secondary Hardening of Tempered Martensitic Alloy Steel (paper by W. Crafts and J. L. Lamont. Mel. Tech. Sept. 194,8, TP 2439)................................................................................................. 345

Jan 1, 1950

By Charles Pack

Die castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into three groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings. In the machine shown in Fig. 3, patented by Doehler in 1910, compressed air is used for forcing the metal into the die. In Fig. 4 is shown another of this type of machine. Here compressed air is applied to the surface of the molten metal to force it into the die. In a machine patented by Chandler in 1914, shown in Fig. 5, the

Jan 1, 1919

By H. P. Willard, R. W. Gates

Basic Inc., has been mining magnesite and brucite for 27 years at Gabbs, Nev. This is a medium sized open-pit mine. The magnesite deposits are in north-western Nye County about 30 miles east of Luning, Nev., on the west slope of the Paradise Range, at an elevation between 5000 and 6000 ft. The magnesite and associated brucite is used to make magnesia refractories employed principally in the steel industry and magnesium oxide for various chemical uses.

Jan 10, 1963

Jan 1, 1969

By A. Thielen

In experiments for the production of steel the principal problem has always been the introduction into, or removal from, the iron of a definite quantity of carbon. Although the solution of this problem had engaged a more or less blindly and empirically directed effort for a long time, it was only with the development of analytical chemistry that the rôle which carbon plays in the constitution of steel was disclosed in its full significance, and that many of the problems confronting the steel-maker were thereby more clearly defined than before. For a long time, and to a certain extent even to this day, the percentage of carbon in steel has been the controlling means of deter mining its quality and hardness. In many cases the percentage of carbon alone has been relied on for judging large consignments, such as the large deliveries of wire-billets and blooms to America during the past twenty years; and though to-day the influences of the other constituents are recognized and many other considerations are taken into account, and though, moreover, some special steels, such as the Hadfield manganese steel, apparently dispense to a certain extent with the assistance of the carbon, yet fix our Bessemer, Thomas, Siemens and crucible steel the carbon still remains one of the most important constituents, and I venture to say it is indispensable. In order to produce in the Bessemer converter a steel of a certain required percentage of carbon, two methods, as is well known, present themselves. By the one the decarburization process is stopped when the desired carbon limit in the bath has been reached ; by the other the bath is completely decarburizecl, and then a calculated amount of carbon added in the form of spiegel, ferro manganese, etc. In Germany the latter method only was adopted, and it was retained when the Thomas-Gilchrist process for the production of low-Phosphorus steel from high-phosphorus iron eame into use, since from the nature of the new process complete decarburization is neces-

Jan 1, 1891

By W. P. Sykes

ThiS investigation was undertaken primarily to establish the relations existing between temperature and mechanical properties in molybdenum, nickel, and an aluminum-copper alloy. Mlolybdenutn (m.p. 2500" C.) was chosen because it is partly similar to tungsten and partly similar to the common ductile metals. Also it is known to furnish, by proper treatment, a desirable material to use in studying relation of grain size and physical properties. The molybdenum used was of the quality that is drawn into wire 0.003 in. in diameter for use as filament supports in incandescent lamps; Chemical analysis shows less than 0.1 per cent. of impurities. Nickel belongs to the same class as iron. Its melting point is 1450" C. and an allotropic change at about 370" C. results in a loss of magnetism above that temperature. This feature made nickel doubly valuable for the purposes of these tests. The nickel used was obtained from the Driver-Harris Co. as 0.090 in. (2.3-mm.) wire, annealed; analysis showed 99.8 per cent. nickel and 0.150 per ccnt. iron. Aluminum is one of the low melting-point metals. Some tensile tests at clevated temperatures have been reported by Bengough but the possibility of learning more with the low temperature and sensitive apparatus available rccommendcd this metal. The samples marked A1 arc an aluminum-copper alloy that contains 3 per cent. copper, 0.42 per cent. iron, and 0.21 per cent. silicon. The presence of the copper somewhat coniplicates the analysis of the results; but the action of copper in aluminum has been studied so that its influence might have been foretold, in part at least. The material and analyses were furnished by the Aluminum Castings Co. The nickel wire, which was deformed at 400" C., was drawn under a bath of molten lead and through a die, which also was immersed in the bath. A thermocouple was suspended in the molten metal to indicate the temperature. Hot oil was uscd as the heating bath for drawing the

Jan 1, 1921

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By E. L. Affleck, W. G. Stevenson

In both Canada and the United States, a company making a public offering of securities must comply with regulations which have been passed by Federal, State and/or Provincial Legislatures. These regulations usually require the distribution of an acceptable prospectus which provides essential background information about the issuer, the project and the share offering. when the public offering has been accepted, the unlisted company may then seek a listing of its shares for trading on a Stock Exchange. Once listed, the company will be subject to rules of the Stock Exchange. This paper will deal with the specific information required for inclusion into a prospectus being submitted for a resource company and particularly those parts of concern to mining engineers and geologists.

Jan 1, 1985

By R. O. Williams

A recent article by Chernock, Singer, Mueller, and Beck 1 which supports the use of the integral of I sin $ d$ for comparing fiber texture data does not settle what happens to I sin ø as ø approaches zero, where I is the diffraction intensity for poles oriented 0 deg from the fiber axis. They indicate that they believe that it should approach some constant value (that is, I increases without bound) and the fact that in reality it does not was a result of the diffraction

Jan 1, 1960

By AIME AIME

COMMITTEES. CANAL ZONE.-Col. George W. Goethals, U. S. A., Chairman; Lt.-Col. H. F. Hodges, U. S. A. ; Lt.: Col. D. D. Gaillard, U. S. A. ; Lt.-Col. William L. Sibert, IT. S. A. ; H. H. Rousseau, U. S. N.; Col. W. C. Gorgas, U. S. A.; Maurice H. Thatcher ; Joseph Bucklin Bishop ; Lt.-Col. Charles F. Mason, U. S. A.; S. B. Williamson ; Major Eugene T. Wilson, U. S. A. ; Edward Schildhauer ; Henry Goldmark ; Edward C. Sherman ; W. G. Comber ; W. B. Corse ; J. A. Walker; Joseph A. Le Prince; J. A. Smith ; Lt. Frederick Mears, U. S. A. HAVANA.-V. T. Polledo, Chairman; Diego Lombillo Clark, Jose Primelles, J. R. Villalon, Jose Artola, J. Ducassi, Luis Morales, Enrique Montonlieu. ENTERTAINMENT ON SHIPBOARD.-William L. Saunders, Chairman; Mr. and Mrs. S. D. Warriner, Mr. and Mrs. Thomas Robins, Mr. and Mrs. George.D. Barron, Mr. and Mrs. R. B. Watson, W. E. Greene. GENERAL MANAGEMENT. .Joseph Struthers, Chairman; Albert E. Vaughan. There were ten sessions of the Institute held for the presentation and discussion of, technical or professional papers. Eight of these sessions were held on the steamer while en route, and two in the ball-room of the Hotel Tivoli, at Ancon, C. Z. Mr. David W- Brunton, President of the Council, presided at all the sessions, except the sixth, at which Mr. Charles Kirchhoff, past President, occupied the chair. The following list includes the papers presented in oral abstract by the authors: First Session., October 24. The Summit Hill Mine-Fire, by W. A. Lathrop, Philadelphia, Pa. Mine-Fire at the Calumet and Hecla Mine, No. 8 Shaft., by S. D. Warriner, Wilkes-Barre, Pa. Fire in the Big Lick Stope, Lykens Valley and Williamstown Colliery, by R. V. Norris, Wilkes-Barre, Pa. Mine-Fire in the Hecksherville Valley, Schuylkill Field, Pa., by W. J. Richards, Pottsville, Pa.. Fire in the Monarch Mine, near Rock Springs, Wyo., by S. A. Taylor, Pittsburg, Pa.

Dec 1, 1910

By Eugene Stephenson

CRITICAL analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,1 Pierce and Lewis,2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or, by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by McWilliams.4 Much of the. dissatisfaction with proration in certain fields is because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the "potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If :no difficulties ever

Jan 1, 1931

By Earl L. H. Sackett

Barite, although not a glamour mineral and probably little known to many of those in the mining business, is produced in the US. in very respectable quantities and is an important factor in the mineral economy of this country. The scope of the various uses of this mineral is perhaps one of the most misunderstood things about it, for it is surprising how many of those with a casual knowledge of the subject speak of its primary utilization in terms of paint pigments and barium chemicals. The life blood of barite utilization, however, is the petroleum industry by virtue of its dependence on this high specific gravity, inert mineral as the weighting material in its drilling fluids. From 80 to 85% of barite usage in the U. S. is accounted for in this manner-in fact, its role in oil well drilling is the only excuse for some of the large-scale barite production facilities which have been developed. Other uses are important and widely varied, but comparatively they are of small scale. They include fine crushed barite of low iron content as a component in glass manufacture, barite as a source material for manufacture of barium chemicals, finely divided barite as a component of some rubbers and ground, bleached barite in pigments. The formerly substantial use of barite in lithopone, however, has declined markedly because of replacement of lithopone by titanium pigments

Jan 5, 1962

By F. A. Olson, S. L. Pohlman

A unique method of measuring weight loss as a function 3 of time, with a sensitivity of 10-5 grams, while leaching copper minerals with a flowing acid leach solution has been developed. Kinetic results obtained coupled with visual and microprobe analyses show topochemical reaction for the leaching of chrysocolla with sulfuric acid. The kinetics follow a shrinking core model and show ion diffusion through a product layer, chemical reaction at the unreacted core interface and mass transfer through the boundary layer as being important.

Jan 1, 1974

Jan 1, 1967

By K. E. Manchester, C. B. Sibley

The feasibility of doping silicon to produce device structres by directly implanting impurity atoms has been demonstrated. Both phosphors and boron ions have been successfully implanted in silicon to produce electrical junctions. Junctions as deep as 1.2 p have been produced by phosphorus ions having energies the order of 80 kev. An electromagnetic separator has been used to controllably produce uniform, large-area implantations for evaluation experimentation. Correlations between junclion depths and ion energies huve been obtained. Orientation effects have been observed and it has been found that the (110) direction is the easy direction for implanting. Monitoring of thermal treatments oj implanted substrates by sheet-resistance measurement indicates a very mild thermal anneal removes most of the damage done during the implantation. These indications are further substantiated by reverse-current measurements of j,inctions Produced by implantation. Electrical characteristics of implanted junctions are compared with those of diffused junctions. We have been interi n the interaction of energetic ions in the III-V groups, in particular boron and phosphorus, with single-crystal silicon to produce type conversion for possible device use. A number of investigators, a few of whom are avies, Kornelson,3 and so forth, have reported on penetration of energetic ions into both amorphous and crystalline solids. While most work has been done with ions of the rare gas and alkali metal groups, some work has been reported by ing, erber,' and others6 in which ions of the 111-V groups have been implanted in single-crystal silicon. A large amount of this work has been done with ion energies in the 100-kev to 1.5-Mev range. An excellent review article has been written by caldin. We have concentrated on ion energies which are in the 10 to 80 kev range, with which over 1500 implanted junctions such as the one shown in Fig. 1 have been produced in silicon substrates with both phosphorus and boron ions. Fig. 1 is a 3-deg angle lap in which the n type area produced by 66 kev P is delineated and the junction is 9500A below the surface. EXPERIMENTAL Implantations reported in this paper were made with the ion source adjusted to produce ion currents in the range of 1 to 2 pa with accelerating voltages varied from 10 to 40 kv. When using doubly charged ions this produced 10 to 80 kev ions. This allowed substrate temperatures to remain below 100°C. Sam- ple movement resulted in beam impingement angle variation of 7 deg from the normal to the substrate surface. Substrate resistivities have been varied through the range of 0.001 to 500 ohm-cm and specimens oriented in three directions, (110), (Ill), and (loo), within 12 deg. RESULTS For the purpose of this paper, discussion of results will be limited to phosphorus implantations with mention of results for boron-implanted silicon. Similar results have been obtained for boron and will be reported at a later date. In Figs. 2, 3, and 4 depth penetration is shown

Jan 1, 1967

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949