Search Documents

By ELLSIVOKTH DAGGETT

THE Berlin gold quartz mine is situated in Nye county, Nevada, on the west flank of the Shoshone range, about 40 miles south and 30 miles west from the town of Austin, the county-seat of Lander county. The distance from Austin is about 60 miles by stage-road. The outcrop of the vein, at the top of the incline-shaft, is situated just at the base of the mountain proper, almost exactly at the intersection of the mountain-side with the gravelly bench that slopes for about three-quarters of a mile to the flatter sage-brush plain, or desert valley, below. The -vein itself consists almost entirely of quartz, with perhaps 2 per cent. of sulphide of iron, copper, lead, zinc and antimony, and perhaps a trace of some of the compounds of tellurium with gold and silver, although none of the latter have been as yet positively identified. The relative proportion, by weight, of silver and gold in the ores, varies in different parts of the vein, from 12 silver for 1 of gold, to 7 silver for 1 of gold. The quartz vein-filling is usually frozen fast to the walls, and is very hard and compact, seldom showing the friable, fissured, or shelly structure often to be found in quartz veins. Comparatively little evidence of relative motion of one wall of the vein upon the other is to be found-a fact indicating that during the formation of the vein, and prior to the extensive movements herein described, little disturbance had taken place. No evidence whatever of metasomatic origin has been observed. On the other hand, occasional occurrences of comby structure, in which the axes of the quartz crystals are at right angles to the plane of the vein, rather indicate deposition from solution in a pre-existing fissure. Spurs, or branches, and small parallel veins, while not en-\

Mar 1, 1907

By Roger L. Brockenbrough

Steels available for mine-shaft applications are discussed, and the use of steel linings for round and rectangular shafts is reviewed. For rectangular shafts, frameworks constructed of square or rectangular steel tubes offer advantages. Also, corrugated steel sheeting provides a suitable alternative to timber lagging for spanning between the main shaft supports. For round shafts, self-supporting cylindrical steel liners, with circumferential stiffeners to prevent collapse, have been used to depths up to 6000 ft. Several large-diameter round shafts have been constructed with a concrete lining and an internal framework: of high-strength low-alloy steel tubes. It is concluded that in any new shaft construction steel designs should be investigated as economical alternatives to designs using other materials.

Jan 1, 1976

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By Leonard A. Wood, A. G. Winslow

Subsidence has occurred in several areas of the upper Gulf Coast region of Texas, although in most cases this is not evident without precise instrumental leveling. As referred to in this report, the region com- prises about 7200 sq miles of the Gulf Coastal Plain and includes all or parts of the following counties: Harris, Fort Bend, Waller, Brazoria, Galveston, Liberty, Chambers, Orange, and Jefferson (Fig. 1 ). Topographic relief is low, ranging from sea level at the Gulf of Mexico to 300 ft or more in northwestern Harris County.

Jan 10, 1959

By R. E. Reed-Hill

The shear continuity conditions under which one mechanical twin may cross another are considered. Twin intersections usually involve various types of slip deformation in addition to twinning. Because the shear of the crossing twin may be partly transmitted through the crossed twin by slip mechanisms, continuity of the twinning shear vectors is not required at a twin intersection. It is concluded that analyses based on twin intersections should not he used as an independent method for deducing twinning elements in newly observed twinning modes. WHEN one mechanical twin passes through another, a twin intersection is said to occur. In the simplest form of intersection, Fig. 1, the crossing of one twin by another is accomplished with the aid of a second-order twin induced, in the twin that is crossed, by the crossing twin. The subject of twin intersections is significant to the field of deformation studies because it has been postulated by cahn1 that twin intersections should occur only under the following continuity conditions: 1) the traces of the primary and second-order twin must be parallel to each other in the plane of the crossed twin; 2) the direction 771 and magnitude, S, of the twinning shear must be identical in the crossing and second-order twins; also, the sense of shear must be the same. If these postulates are valid they constitute a valuable tool for determining twinning elements of newly observed twinning modes in metals. In his classic paper in 1953 on the plastic deformation of a uranium, Cahn1 used these continuity conditions to deduce twinning elements for several uranium modes. However, in the same year, pratt2 showed that both of Cahn's continuity equations were violated for (1012) twin intersections in zinc. Later, Kiho and Maruyama3, 4 showed that Cahn's second postulate was violated in {301) and (101) twinning in tin and (101) twinning in bismuth. In spite of this documentation that Cahn's second postulate is often violated, several recent papers5'6 have been published which have attempted to use the condition of continuity of twinning shear vectors for the evaluation of twinning elements. The primary purpose of this paper is to call attention to the possible ambiguity inherent in applications of Cahn's postulate, and to present additional information concerning the nature of twin intersections.

Jan 1, 1964

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By Arthur E. Focke

IF a metallurgist employed in an industry producing mechanical parts or assemblies wishes to make the most of his opportunities he will be concerned with every use of metals in that industry. He will not only take part in the testing and treating of the metals used but will assist in their selection and study their behavior in processing and in service. In addition, he will attempt to develop an understanding of the problems involved in the use of the metals in all plant tools and equipment. Metallurgists that follow this course will soon recognize that frequently too little thought is given to the effect of the design of parts on the way the metal in them is expected to behave in service. He will come to realize that changes in the design of a part will often be much more useful than changes in the hardness, strength, composition, or structure of the metals used in them. Does this mean that a metallurgist is out of place in these industries and that he should leave the field to others or be content to fill only a minor role?

Jan 1, 1947

By T. H. Aldrich

(Chattanooga Meeting, October, 1908.) Tars paper is intended only to give a preliminary account of experiments made, and conclusions reached, concerning the treatment of certain refractory low-grade gold-ores, the profitable reduction of which may furnish a useful guide to the solution of similar mining and metallurgical problems, not only in the gold-bearing belt of the Southern United States, but perhaps in other regions also. It must be regarded as simply a ?report of progress," preceding a more elaborate and conclusive report of regular practice. The mines of the Hillabee Gold Mining Co. are located upon what is generally known locally as Hog Mountain, on the northern edge of Tallapoosa county, Ala., about 15 miles from Goodwater and 14 miles from Alexander City, stations on the Central of Georgia Railway. Gold has been known since 1839 to exist on this property, where it was discovered in that year by a man named Johnston. The property was worked for placer-gold by the old miners, and there are now the remains of four attempts to operate it by stamp-mill and plate-amalgamation. The present owners purchased it in 1896, and since that time they have experimented at frequent intervals, in order to devise a process that would satisfactorily recover the gold. In 1903 regular operations were begun. Geologically, the mountain consists of an intrusion of what has been pronounced true granite in altered sedimentary slates. The cooling of the granite produced shrinkage-cracks, which have become veins. There is considerable question as to the period of the slate formation; but it is undoubtedly, in my opinion, of Carboniferous age. The veins, about 50 in number, strike N. 60° to 80° E.; dip approximately 65° from the horizontal; vary from a few inches to 25 ft. (being in gen-

Nov 1, 1908

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes.

Jan 1, 1950

By Albert Sauveur

Jan 1, 1924

By Albert Sauveur

Jan 1, 1924

By T. Fraser, R. L. Sutherland

Under a cooperative agreement between United States Bureau of Mines and the Truax-Traer Coal Company, some operating-scale experiments have been made with the cyclone thickener in the preparation plant of the Shamrock No. 1 mine at Kayford, West Virginia. These tests were made with a 14-in. cyclone of the type developed by the Dutch State Mines in Limburg. It was applied experimentally to the thickening of solids in washery water to obtain performance data to show the range of sizes that may be recovered and other operating characteristics that would indicate the field of usefulness of this device in coal preparation practice. This is a progress report only. It covers results obtained in a series of 17 tests of the operation of what has been considered a unit of commercial size operating on suspensions of fine coal mixed with a relatively small amount of freeimpurities. The underflow material, after further dewatering in centrifuges, is a marketable grade of coal.

Jan 1, 1949

By George A. Roche

Investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria used to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of investment strategy for two of the three mutual funds sponsored by the Price organization and for its private clients. However, during the past five years inflation has accelerated due to a variety of factors including the inability of government to meet seemingly unlimited needs with limited revenue sources.

Jan 4, 1972

By W. A. James

NATURE endowed the Niagara Frontier with great resources but it was the molding of these resources by the early pioneers that assured its future development. This great industrial district of New York stretches along about fifty miles of shore line on the eastern end of Lake Erie and the Niagara River, embracing the two counties of Erie and Niagara, with the city of Buffalo about in the center. This location at the junction of the eastern end of the Great Lakes and the western boundary of the State, a great focal point of land and water, transportation, guaranteed the development of the Frontier. Although the first white settlers came to this section in 1784, it was not until after the turn of the nineteenth century that real development started. Perhaps the most significant influence in the early days was the completion of the Erie Canal between Buffalo and Albany in 1825. This then monumental achievement gave Buffalo an advantage in the race for the best trade route to the Western

Jan 1, 1938

By H. E. McKinstry

LIKE nearly everything else, mining geology has been reconverting. Many geologists had been in military and other government service. Many more, with mining companies, had been working primarily toward increasing production from known reserves. All of these are turning now toward their normal peacetime endeavor-the search for new ore; for most mining companies, finding themselves with accumulated deficits in development work, are more than ready to go ahead with their postwar plans made a year or more ago but still stalled at the close of 1945 for lack of man power. These plans include not merely development in the old home camp but also wide exploration for new prospects both domestic and foreign. Most of the large concerns have geologists and engineers in the field in the United States, despite the outlook for higher mining costs here, and at least half a dozen strong American companies are already investigating opportunities abroad, notwithstanding past unhappy experiences in certain Latin-American nations which have welcomed capital but later found means of preventing investors from reaping the reward of their enterprise. A few of these new foreign expeditions are following well-planned programs, but too many, in their haste to get any sort of footing, are proceeding without well-considered policy. with the result that their geologists can do little more than desultory scouting.

Jan 1, 1946

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer's4 results. The information in Beck's compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas'6 X-ray studies of Jones and Powell's specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965

H. Van F. Furman, Denver, Colo. (communication to the Secretary): There are some statements in Dr. Carpenter's interesting paper which appear to require explanation, if not modification.

Jan 1, 1901