Search Documents

By R. B. Gordon, D. A. Koss

Ultrasonic-atlenuation changes due to the formation of free dislocations have been observed during tensile tests of magnesium and LiF single crystals and samples of polycrystalline Results on the LiF and samples are similar: A preyield attenzration increase is observed which, however, be-corlzes smaller as the magnitude of the drop in load al yielding increases. This indicates that the yield point observed in these materials is due to dislovation rather than dislocation unpinning and that the initial density ' free dislocations must be low if the yield point is to be sharp,. Tests on the magnesium ere conducted at both 27" and 200C. Magnesium has the unusual property that the yield drop is larger at the higher test temperature and is accomplished by a decrease in attenuation. The latter is due principally to the temprovary pinning of detained dislocations by highly solute atoms. After strain aging., a stress as low as 0.3 bur suffices to unpin dislocations; microstrain measuements of sufficient sensitivity should. reveal plastic flow at stress levels this low IN another paper,' we describe the technique of simultaneously observing ultrasonic-attenuation changes and plastic microstrain during deformation of spher-oidized carbon steels. Changes of ultrasonic attenuation indicate damping effects caused by the oscillation of long, freely moving dislocation segments. Simultaneous microstrain measurements are used to indicate total dislocation motion. The dislocation-damping observations are most useful in the study of the early stages of deformation where the dislocation density is low and the plastic strain is small and relatively difficult to measure. Particularly interesting results are found in materials which display sharp yield points. Observations of these phenomena are reported here for three materials: single-crystal LiF and magnesium, and poly crystalline molybdenum. EXPERIMENTS Dislocation-damping effects were observed by measuring changes in acoustic attenuation with the ultrasonic-pulse method. The end faces of each of the specimens were ground flat and parallel and a quartz 10 Mc per sec, x-cut transducer was attached to one face. The bonding agents used were: a) "Nonaq" stopcock grease with magnesium, b) beeswax with LiF, and c) salol with molybdenum. With the LiF, the best acoustic signals were obtained at 45 and 50 Mc per sec; all other measurements reported are at 10 MC per sec. The Sperry Ultrasonic Attenuation Comparator2 was used to measure attenuation changes. In the

Jan 1, 1967

By D. W. Brunton

Discussion of the paper of D. W. Brunton, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 33, September, 1909, pp. 837 to 855. WILLIAM' KENT, New York, N. Y.:-The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is au admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly give's the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that. the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation' of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer-Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer-Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric . transmission, electric smelting. Work of the Chemist and Metallurgist-Explosives, chlorination, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist-Economic geology. Work of the Mining Engineer-Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing

Jan 1, 1910

By R. T. Keyes, R. B. Clay, L. L. Udy, V. O. Cook, M. A. Cook

Based on compressibility and stress wave velocity in rock, initial explosive loading conditions, the thermochemistry of the explosive and reasonable description of the pressure-distance relations behind the shock front, the distribution of energy between the products of detonation and the burden are estimated as a function of time for various loading conditions. These include 'powder factor', loading density A (fraction of borehole occupied by explosive), and the explosive itself. Factors responsible for rock fragmentation are discussed in terms of: 1) 'release wave fracturing', 2) 'shear wave fracturing', and 3) 'release of loading fracturing' or 'rock bursting'. Release wave fracturing appears to occur only in the immediate vicinity of free faces, and shear wave fracturing only adjacent to the borehole under normal blasting conditions. Rock bursting is thus considered to be the most important means of rock fracturing in blasting. Means for maximizing it are considered. The most important factors to consider include maximum available energy A, explosive density p1, loading density A and 'powder factor'. Maximum efficiency is attained in general by maximizing the A . p1 product. This is achieved by using high density explosives at a loading density of unity (A = 1.0). Ways for achieving this condition are discussed. The bulk-handled aluminized slurry blasting agents have the desired properties for achieving optimum conditions for high blasting efficiency based on the theory outlined herein. Factors considered most important in the blasting of rock are: 1) The maximum available energy A, determined by the heat of explosion Q and the mechanical efficiency ?, a factor intimately associated with the mode of application (A = Q at highest gas concentrations). 2) The 'borehole pressure', pb, or the maximum pressure developed in the borehole after passage of the detonation wave and before the burden has had time to move or become compressed appreciably. (Owing to the short duration of the detonation wave at any particular point in the borehole, the fact that the explosive may not always fill the borehole completely and the further fact that the burden may not actually see the detonation pressure, the borehole pressure is considered more significant than the detonation pressure p2 as a performance factor in borehole blasting.) The borehole pressure is determined by the explosion or adiabatic pressure, p3 , and the loading density, A, or the fraction of the borehole filled by explosive. 3) The physical conditions important in the application of the explosive are: a) The 'powder factor,' (We/Wr), or the ratio of the wt of the explosive to that of the rock being blasted expressed as lb per ton or more generally in lb/cu yd. b) The bulk density, p1 ?. c) The 'burden' or 'line of least resistance,' the spacing between boreholes, the geometry of the borehole pattern and sequence of firing. d) The physical and chemical properties of the rock, most significant of which are possible heterogeneties, such as faulting, prefracture, and greater than micro-scale chemical heterogeneities. (This factor is not considered here but deserves a great deal of careful consideration.) All of these factors need to be carefully considered in the most economical engineering of a blast. Here is considered firstly an outline of the present status of dynamic rock mechanics, particularly as it pertains to blasting. The factors pertaining to the most efficient application of blasting agents are also considered, followed by a discussion of methods of application to achieve optimum explosives performance. ROCK MECHANICS Dynamic rock mechanics is currently a rapidly developing science contributing greatly to a better understanding and consequently the more effective application of explosives in blasting of rock.1-22 Basic to the development of the science of dynamic rock mechanics were the advances of Goransen23 and the Los Alamos and NOL groups24-28 concerning rock and stress wave phenomena and the transmission and reflection characteristics of stress waves at interfaces between different media. Basing considerations on this new knowledge as well as new experimental methods of study (ultra-high speed streak and framing cameras and electronic timers) the theory of fracture and failure of solids under impulsive loading by stress waves developed rapidly.14,16,27-29 Also the

Jan 1, 1967

By Charles C. Goddard

Since discovery of silver-gold lode deposits in 1864, the Butte district has produced more than $2.25 billion worth of copper, zinc, manganese, silver, and gold, an unprecedented value in the mining world. Exhaustion of the gold placer deposits along Silver Bow Creek, southwest of Butte, forced the early-day placer miners to turn their attention to the bold out- crops of the many veins exposed on the hillsides above the placer diggings. These outcrops bore silver and gold, and enough so that many lode claims were located. Such famous silver mines as the Alice, Moulton, Magna Carta, Nettie, and Blue Bird were developed. These and many smaller operations contributed to making Montana the leading silver-producing state in the 1880's. As depth was gained in the silver mines in certain parts of the district, occurrence of zinc minerals became troublesome. Zinc was not recoverable at the time, and in the chloridizing, roasting, and amalgamation of the ores, silver and gold recovery was greatly reduced. A period of active silver mining continued until 1892, when a decline in the price of silver brought the silver mining period to a close. Elsewhere in the district it was discovered that while some of the veins contained silver ores in the oxidized portions, the predominant minerals that were deeper were copper-bearing. Marcus Daly exposed rich copper ore on the 300 level of the Anaconda mine in 1891, and mining in the district disclosed that copper was destined to be developed in abundance. Early copper ore shipments were made to Swansea, Wales.

Jan 3, 1959

By Charles S. Barrett

THIS paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstructures. About 12m exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,1 and a number of these have been selected to illustrate the results obtained. Prints are also included showing the common types of falsities-to borrow a term from the biological field, the "artifacts." In brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. n addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains. Since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. SPECIMEN PREPARATION AND PHOTOGRAPHS Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for repeated polishing and etching (each successive polish becoming less severe and each etch lighter), since the final etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and IC, the replicas used were of silica, deposited up0n polystyrene and floated from the polystyrene in ethyl bromide according to polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1943

By CHAS. A. R. LAMELY

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varyng low dips in varying directions, and underlie large areas of the district. Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that sufficient tonnage existed to justify a redesigning of the whole operation, surface and under- ground. After four years of general study, the following program was planned :

Jan 1, 1949

By Clyde E. Williams

DESPITE the confusion resulting from the depression and the beginnings of recovery, important progress in all branches of iron and steel metallurgy has been accomplished during the year 1933. Research work has been intensive and highly technical, with increasing attention paid to fundamentals. Plant application of research developments has been rapid. Highly specialized laboratory methods were used for the study of iron-ore concentration methods. More attention has been given by the blast-furnace operator to the sizing of ore and the elimination of fines from the charge by the use of sinter. Combustion in the open-hearth has been placed under better control and the insulation of open-hearth furnaces has spread rapidly, with resultant higher fuel efficiency and better control of the melting and refining operations. Control of iron oxide content in the slag and the determination of iron oxide and other inclusions in steel received great attention during the year.

Jan 1, 1934

By A. F. Crawley

THIS communication reports measurements of the densities of dilute liquid alloys of 0.1 and 0.5 pct Ag in Sn over temperature ranges of 170" and 210°C, respectively, above the melting point of pure tin (232°C). The work was earried out to provide accurate density data for some liquid diffusion studies performed by Davis.1 Densities were measured using a pycnometric technique established in this laboratory. Earlier papers2, 4 attest to the accuracy of ±0.05 pct and the reliability of the method. Tin, 99.999 pct pure, and silver 99.99 pct pure, were melted in a graphite crucible in a vacuum furnace and held at temperature for 10 hr to ensure homogenization. Ingots suitable for machining

Jan 1, 1970

By Roger K. Clifford, Gary W. Hudiburgh

The amine flotation of feldspar from a magnetite concentrate produced at a domestic concentrator was investigated using zeta potential measurements, Hallimond tube flotation tests, and laboratory-scale flotation tests. The point of zero charge of six feldspars (microcline, orthoclase, albite, anorthite, anorthoclase, and oligoclase) range from pH 1.4 to 2.5. Hallimond tube flotation tests using amine flotation reagents were performed on these feldspars and on gangue material (quartz, albite, and microcline) from the magnetite concentrating plant. Laboratory-scale (623 g and 2500 g) flotation tests were performed on the magnetite concentrate to float the feldspar. The effects of three different collectors, two levels of collector concentration, three pH levels, starch, HF acid and regrind were investigated.

Jan 1, 1977

By D. W. Loucks

There is plenty of evidence to indicate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money: to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before, automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system.

Jan 1, 1949

By J. Robert Van Peli

IT was a strange but highly fruitful marriage-that union of hardy explorers, seeking the rich treasures of copper in the Lake Superior wilderness, with Boston's aristocracy of brains, capital, and enterprise. This historic wedlock, which has continued happily to the present day, was the means by which the wealth of Lake Superior's copper was won for the use and benefit of an expanding America. One branch of this family tree, the western branch, begins with prehistoric Indian miners, embraces the early French explorers of the Upper Lakes, and finally includes the British and American pioneers who reduced the vague rumors of copper to known fact and actually began the mining of copper in the wilderness. The other branch, the New England line, begins

Jan 1, 1948

By Fred C., Fred C. Bond

Comminution energy is principally energy of deformation before breakage, which appears as heat. An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories are compared.

Jan 1, 1950

By Frank Firmstone

In 1871, two furnaces at the Glendon Iron Works, which had been blown out on account of the "coal strike," were altered from the open-top plan with side flues for collecting the gas, to closed tops with cup and cone. In one furnace the suppression of the side flues permitted a considerable alteration in the profile, but in the other (No. 5) no change in this respect was made; the side flues were simply bricked up and new ones cut through the sides close to the top. This furnace was in blast over four years, and we can, therefore, form a pretty good idea of the effect of the alterations on the furnace process. The principal dimensions are; Height 72'; greatest diameter, 18'; diameter at tuyeres, 8'; diameter of top, 10'; diameter at stock line (point at which the top of the materials is kept), 11'; cubic contents, 11,900 cubic feet. The table below shows the average results for periods of twentysix weeks each. 1st, of the open-topped furnace; 2d, of the furnace with the first charger used, which was an ordinary cup and cone (diameter of cone 5' 2") 3d, with the charger used ever since, a " double " cone 7' 5" diameter outside, having a central opening 3' in diameter. The diagram (Plate 11) shows the daily variations, in the grade of the irons for the same periods.*

By E. M. Wise

THE properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. GENERAL REQUIREMENTS In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should be good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depilatories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 lb. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800° and 1200° C.

Jan 1, 1928

By Eugene Holman

UINQUESTIONABLY the petroleum industry not only can supply the world's present oil requirements but even can meet a considerable increase in demand if it should come. The United States produced last year 1 1/3 billion barrels of crude oil, or more than 60 per cent of the world's total. It could have provided more, if needed, because we has a large shut-in crude producing capacity. Our refining capacity of 4,500,000 0 barrels per day is more than 2 per cent above our average refinery run for 1940. Adequate crude supplies and manufacturing facilities also exist outside of the United States. Large crude reserves exist in South America, in Iran and Iraq, in Russia and Romania, in Sumatra and adjacent islands. The refineries of the Dutch West Indies, of Iran, and of the Netherland East Indies are well located in relation to crude reserves and world trade lanes. Furthermore, flexibility in the manufacturing facilities permits adjustment of yields to meet a considerable range in variations between demands for products. Only with regard to 100-octane aviation gasoline is there any apparent refinery problem. Even here so far as this country is concerned, additional refining facilities can be installed well within the time that would be required to turn out the airplane engines which will use this super fuel.

Jan 1, 1941

By H. T. Bowman

For more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the I860's it was recognized that the process would benefit by some type of instrumental contro1.l IIowever, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower's eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham,3 A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient menoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. Carbon-FeO Relationship In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by Mccutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per. cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a . different method than were those

Jan 1, 1942

By H. T. Bowman

For more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the I860's it was recognized that the process would benefit by some type of instrumental contro1.l IIowever, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower's eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham,3 A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient menoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. Carbon-FeO Relationship In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by Mccutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per. cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a . different method than were those

Jan 1, 1942

By W. I. Garms, J. L. Stevens

BECAUSE of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following resume of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. MILLS USED Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was I3 1/2 in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 16 2/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. INITIAL TEST During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1946

By Karl V. Lindell

THE Jeffrey mine of the Canadian Johns-Manville Co., Asbestos, Que. has operated for a number of years, supplying the parent company, Johns-Manville, raw material for asbestos products. The mine is situated in the 70-mile-long serpentine belt running from Asbestos, Que. on the west to East Broughton on the east. This district is the most important producing area in the world of quality spinning-fiber asbestos, with 11 operating mines supplying 70 pct of the world's needs. The Jeffrey mine, located 90 miles from Montreal and approximately 35 miles southwest of Thetford, accounts for 50 pct of the Canadian asbestos output. Production from the Canadian serpentine belt is the chrysotile asbestos, which is considered the best available for spinning. Consumers in the United States prefer the clean, fine fibers of the Canadian chrysotile of the type produced by the Jeffrey mine. Mining In 1881, when the mine was first opened, all work, including drilling, was done by hand. The deposit, located on a hillside, was first worked as a sidehill cut by hand drilling 15-ft holes and blasting with black powder. The fiber was chiselled from the broken rock. Hand derricks, later powered by horses, were used to raise the rock as the pit deepened. Eventually, the pit became so deep that derricks were, by necessity, replaced by aerial tramways. In the late 1930's, further deepening of the open pit, with the resulting constriction of the pit bottom brought about the need for altering the mining system then in use. The high ratio of overburden to be handled to mill ore mined and the value of surface structures, not company property, that would be destroyed in expanding the area of the pit, definitely indicated vertical rather than horizontal expansion would have to be used. One exception to this was that a small area on company property to north and east of the pit could be opened up. The mining problem then resolved itself into two phases; make the small lateral expansion and as rapidly as possible choose a mining method that would expand the mine vertically. Several methods for vertical expansion were studied and rejected. Methods considered included shrinkage stoping, block caving, glory holing, and various modifications of open workings. Block caving was finally accepted as the most suitable method of underground development. Cost factors and production were important factors in the decision, also, the asbestos mines in the Thetford area were already having success with this method. Original plans provided for the lateral expansion of the open mine where possible and beginning the underground operation. This program was based on the open pit being worked out in 1954, with the underground development and production gradually increasing until the open mine was depleted. In 1949, the plan was changed to allow underground development to progress at maximum so that underground output would be 550 tons per hr by 1951. Any deficit in ore would be mined from the open pit. This change permitted extending the life of the open pit through 1964 and in this time would make available a large quantity of readily attained ore. Block Caving at The Jeffrey Mine Plans for the underground operation were formulated on a 12,000-ton-per-day basis, and the adaptability of block caving methods to high production presented a desirable situation. As shown in the main-haulage plan, a continuous loop was laid out for smooth operation of the underground railroad from the loading points to the underground crusher. A feature encountered at the Jeffrey mine, as well as other asbestos mines using caving methods, is the large size of caved material, requiring that ore be crushed before hoisting.

Jan 1, 1952

By Cloyd M. Smith

A few years ago, the Ventilation Committee established the practice of resenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measnrements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies. The statement was accompanied by a questionnaire on the use of the rotating vane anemometer and by one describing two methods of using a mechanically held anemometer. The questionnaire will be considered first. The questionnaire and statement are as shown on pages 5 and 6, the committee members and respondents are given on page 4, and the general comments of the latter on page 5. Questionnaire 1. Has your company or agency issued written instructions for care and use of anemometers? If so, please enclose a copy with reply. Only one answer, McElroy's, was affirmative. It gave reference to Bureau of Mines publications1'5 which recom- mend the hand held anemometer for rough measurements and indicate that am accuracy of 5 pct can be had if calibration and method factors are used. Mathews said that instructions are principally oral while Maize reported that state inspectors of his department are well trained in use and care of anemometers. 2. Are your anemometers calibrated periodically? If so, by their manufacturer? or by? Are calibralion corrections applied to all observed mean velocity readings? Only one respondent, Lee, answered negatively as to calibration. This means that anemometers are generally calibrated but the questionnaire failed to ask how often this is done. As no one volunteered the information, we have no data on this point. In six cases the instruments are sent to their manufacturers for calibration. but Krickovic reports that his company limits manu-facturers' calibrations to anemometers which are used by operating personnel; those used by the engineering department being calibrated by U. S. Bureau of Standards. The Anaconda Copper Mining Co. has its ventilation engineers calibrate its anemometers. Most of the respondents say that a calibration correction is applied to each mean velocity reading, but Krickovic limits this to surveys made by the engineering department. Since Lee does not calibrate, he has no correction to apply. Maize reports that his department has its anemometers calibrated but does not apply corrections. 3. Do your men hold the anemometer by hand in measuring air flow? for 1 min? or traverse the section? for 1 min? or at? points for 5 sec each? Of 10 replies, 6 were "yes," 3 were "no," and one was "seldom" with respect to holding by hand. Among the six hand holders, four hold in a central position in the measuring section for a minute, except that two of them, Krickovic and Matthews, traverse the section by hand for survey or fan test. Their operating personnel hold by hand, centrally, for routine measurements. McElroy sometimes traverses with hand-held anemometer in rapid survey work. 4. If the anemometer is not held by hand, how is it supported? Augustadt supports the anemometer on an adjustable rod, Condon on "a rod of sufficient length to reach all points with observer standing in one position throughout traverse and at arm's length from plane of traverse." I presume that arm's length must be interpreted liberally enough to allow for arm movement, otherwise it would be impossible to manipulate the anemometer throughout the traverse section. Mancha upholds Condon in this method of traversing. Glanville hangs the anemometer on the end of a 4-ft staff by the hasp at the top of the anemometer frame. McElroy mounts it on the end of a rigid square shaft, 12 in. long, the staff being at right angles to the axis of the instrument. He traverses the section in two halves, holding the anemometer 3 feet from his body.

Jan 1, 1950