Search Documents

By J. L. Giove, J. M. Hodge, R. G. Storm

The hardenability effect of molybdenum has been evaluated by a number of investigators, including one of the present authors.1,2,3,4,6 Considerable discreMncy exists, however, among the results of these various investigators, and two of them, Brophy3 and Kramer,4 have indicated that the apparent hardenability effect of molybdenun would vary, depending upon the other alloying elements in the steels being considered. The results of previous, unpublished work conducted at the Duquesne Works Laboratory of the Carnegie-Illinois Steel Corporation also have indicated significant differences in the hardenability effect of molybdenu~n in nickel and in chromium steels. The present investigation was undertaken in an effort to establish the mechanism governing this difference in the hardenability effect of molybdenum. This work involved both end-quench hardenability and isothermal transformation tests on two series of steels of varying molybdenum content. One steel contained 3 pct nickel and the other 1 pct chromium. It was hoped that such studies would shed further light on the mechanism of this behavior. Materials and Experimental Work MATERIALS The chemical compositions of the steels used in this investigation arc shown in Table 1. These steels were furnished by Battelle Memorial Institutc in the form of 100-lb induction furnace ingots. The top half of each ingot was forged to 1 3/8-in. square billets and then rolled to I-in. round bar stock for isothermal transforma- tion studies. The bottom half of each ingot was forged into approximately 1 1/4-in. rounds for end quench tests. All of the steels were normalized from 1650°F and tempered at 1100°F before nlachming to end quench or isothermal samples. END-QUENCH TESTS standard l-in. diam end-quench tests were made on each of the steels. The test bars were austenitized at 1600°F for 30 min,, quenched in a standard Jominy jig, and hardness surveys were made in all tests. The 95 pct martensite point was deterInined from hardness values5 and cheeked by metallographic examination. The jominy distance values for 95 pct martensite were converted to hardellability values in terms of ideal diameter (Dl), using a revised carve for the relationship between Jominy distance and ideal diameter. This curve was based on the cooling time from the A1 to the bainite nose temperatures rather than on the usual criterion of half-temperature time. The cooling rates as determined by Russell and Williamson9 were used as a basis for this relationship. The derivation of this curve is described in detail in the appendix. ISOTHERMAL TRANSFORMATION STUDIES Samples for the isothermal transformation studies were quarter sectors of 1/16.is-in. thick slices from the 1-in. round bars. All samples were austenitized for a total the of 15 min., transferred rapidly to a lead bath for isothermal transformation, and brine quenched from the lead bath. A time of 3 see was allowed for the sample to come to the temperature of the lead bath, and this time was not included in the isothermal transformation times. Each sample was examined metallo-graphically at a magnification of 100 diam. The per cent transformation was estimated by comparison with standard micrographs, and the values were plotted against the on log/log coordinate paper. At least 4 and as Inany as 10. points were plotted for each steel. A line was drawn through the points for each steel, and the times for 5 pct transformation were obtained from the plot for each steel. Isothermal transformation diagrams in terms of 5 pet total transformation, covering the temperature range of 800 to 1200°F, were determined in this manner for an austenitizing temperature of 1600°F. The times for 5 pct transformation at the bainite nose for austenitizing temperatures of 1800 and 2000°F were also determined in the same manner. These times for 5 pct total transfor-

Jan 1, 1950

By M. H. Gaskell, D. M. Kehn, G. T. Pyndus

A correlation of the bubble point pressure for black oil systems is developed using the standard physical-chemical equations of soiutions. The correlation is based on 158 experimentally measured bubble point pressures of 137 independent systems and is expressed in terins of the usually measured field pnrameters— flash separation gm-oil ratio, rank oil gravity, total gas gravity, and reservoir temperature. The data were obtained on systems produced in Canada, Western and Mid-Continent01 United States, and South America. The average error (algebraic) in the representation is 3.8 per cent, and the maximum error encountered is 14.7 per cent. INTRODUCTION In the absence of experimentally measured properties of reservoir fluids, it is often necessary for the field engineer to make estimates regarding the fluid properties based on the usually measured producing parameters. To aid in these estimations, various correlations have appeared in the literature in recent years. Among the pertinent properties of interest is the bubble point pressure. A correlation for this parameter has been reported by Standing'. However, this correlation was based essentially on California produced crudes and this limitation was pointed out with its presentation. The correlation presented in this paper utilized data on crude oil systems from Canada, Wes- tern and Mid-Continental United States, and South America. CORRELATION DEVELOPMENT The basic assumption used in this development is the same as employed by Standing', There is a wide variety of ways to combine these parameters; however, in this instance the combination was made on the basis of Henry's law2. Accordingly, the relationship proposed is Although Eq. 2 defines an individual system, it is of limited value since H' is a function of gas-phase composition and the system temperature. It was observed that for the systems where the bubble point was measured at several temperatures that the ratio of the bubble point pressures and the ratio of the corresponding absolute temperatures (R) were practically identical. Thus, for correlation purposes the bubble point pressure may be taken as a direct function of the absolute temperature. This relation is valid only for those systems that are not near the critical point. Accordingly, this correlation will be inadequate for systems in the region of the critical point. The solubility of the various hydrocarbons found in the gas phase increases with the molecular weight. Thus, the saturation pressure should be inversely related to the gas gravity. Applying these principles to Eq. 2 and rearranging terms gives: The variables 02 the left side of Eq. 3 were designated as the "hubble point pressure factor". The number of mols of tank oil per barrel is a function of the "mclecular weight" of the tank oil. Although the tank oil is a complex mixture, it was assumed for the purposes of this correlation that a unique molecular weight could be assigned to a given oil. This was designated as the "effective molecular weight", and was related to the oil gravity, This empirical relationship was developed simultaneously with the correlation by assuming values of M,. and working to obtain a smooth curve for both the correlation and the effective molecular weight. The relationship between the oil gravity and the effective molecular weight used in this correlation is shown in Fig. 1. The effective molecular weight is somewhat higher than the molecular weight of the C fraction. The difference between these values is largest for the low-gravity systems. It is noted that this effective molecular

By AIME AIME

EITHER the 2300 people who came to the Annual Meeting were in a better frame of mind or they were resigned to their fate, or it was a better meeting than usual. Whatever the reason, at the 1nstitute?s 148th meeting the attendance was better than ever before, things went more smoothly than in some previous years, and complaints appear to have been almost entirely absent. Patience was sometimes reauired but. almost without exception, it was forthcorning the well-known recession seems to have given many members enough leisure time to come to the meeting without depriving them of the tangible wherewithal to come.

Jan 1, 1938

By William Priestley

IN THE manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and elastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungsten, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured-by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. DESIGN OF GUN FORGINGS In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun are made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The elastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge.

Jan 12, 1921

By J. D. Livingston, H. E. Cline

The lamellar-dendritic transition in Sn-Pb alloys near the eutectic composition has been studied at high growth rates. Lamellar structures were found over a substantial range of tin-rich compositions, and this range extended to increasingly tin-rich concentrations as growth rate increased. These results are discussed in terms of stability and competitive-growth arguments. Various experimental and structural limitations to the rate of directional solidification are discussed. The rate of heat removal at the heat sink is the major experimental limitation. ReCENT interet1,2 in the use of fine composite structures produced by directional solidification of eutectic alloys makes it important to determine the range of composition and growth conditions that yield such microstructures. Because increasing growth velocities produce increasingly finer microstructures, it is particularly significant to determine the factors limiting the rate of solidification. Mollard and Flemings3 have shown that composite structures, free of primary dendrites, can be obtained in Sn-Pb alloys of off-eutectic composition. The composition range of composite structures was found to increase with increasing values of G/V, where G is the temperature gradient and V is the growth velocity. These results are in good quantitative agreement with an analysis of the stability of a planar eutectic interface.4 This analysis specifically predicts that over a small range of compositions stable lamellar structures will be obtained even for G/V = 0, hence, even at very high growth rates. The lamellar-dendritic transition in Sn-Pb alloys has also been analyzed with a model based on competitive growth between dendrites and the composite structure.576 This treatment, based on earlier work on organic eutetics,7 predicts that the composition range yielding composite structures in Sn-Pb will increase rapidly at high growth rates. An increase in the composition range of composite structures at high growth rates was recently observed in Cu-Pb alloys near the monotectic composition.8 In view of these results, and the predictions of the stability and competitivegrowth analyses, it was decided to study the lamellar-dendritic transition in Sn-Pb alloys at high growth rates. EXPERIMENTAL Using 99.999 pct pure materials, a series of Sn-Pb alloys were prepared containing 16.8 at. pct to 27.6 at. pct lead. (Eutectic composition is 26.1 at. pct Pb.) Ingots were extruded to 0.175 in. rod, and some rod was drawn to 0.070-in. wire. Directional solidification was accomplished in two different ways, Fig. 1. For growth rates up to 2 x 10-1 cm per sec, a 0.175 in. diam sample was placed in a graphite crucible 5 in. long with 0.250 in. OD and 0.035 in. walls. Samples were melted under flowing argon in a vertical, platinum-wound furnace, and solidified by driving the crucible downwards through a \ in. hole in a water-cooled copper toroid, Fig. l(a). An insulated chromel-alumel thermocouple was imbedded in the center of a representative sample, and moved with the sample during solidification. The local temperature is plotted against the distance travelled by the sample in Fig. 2. As the growth rate increased, the solid-liquid interface moved closer to the water-cooled toroid and the temperature gradient increased. At growth rates above 10-1' cm per sec, heat was not removed fast enough and the sample moved into the toroid in the liquid state. The curve for V = 2 x 10-1 cm per sec shows a plateau caused by incomplete removal of latent heat from the interface, a problem which will be discussed later. To improve the heat removal, the toroid was cooled by nitrogen gas precooled in liquid nitrogen. This allowed successful solidification at rates up to 2 x 10-1cm per sec. Higher solidification rates required still more effective heat removal. Samples 0.070 in. in diam were placed in graphite tubes 0.125 in. in diam with 0.020 in. walls. Instead of cooling by sliding contact with a cooled toroid, these thinner samples were sprayed or directly immersed into water, Fig. l(b). After solidification, samples were stored in liquid nitrogen until they could be examined metallographic-ally. The surface was prepared with a diamond-knife microtome, followed by a light etch. The presence or absence of tin dendrites, Fig. 3, or lead dendrites, Fig. 4, was noted by optical microscopy, usually of a transverse section near the center of the sample. Replicas of the surface were prepared and examined in an electron microscope to resolve the fine lamellar structures, Fig. 5. The structures observed at various compositions and growth rates are summarized in Fig. 6. Composite structures were observed at increasingly cin-rich compositions as growth rate increased. This transition from dendritic to composite structure with increasing growth rate was also demonstrated by solidifying half a sample at a slow rate and then suddenly increasing the growth rate by lifting the furnace and quenching the sample with a water spray. A longitudinal section of this sample, Fig. 7, shows that the tin dendrites, which extended ahead of the slow-moving composite interface, were bypassed by the composite when the growth rate was increased. The range of composite structures at high growth rates was limited by the appearance of primary lead dendrites on the tin-rich side of the eutectic composition. Observation of representative longitudinal

Jan 1, 1970

By Cornelius F. Kelley

EVERY man connected with the mining industry should take a significant pride in the fact that he belongs to an industry and to a profession that, from the beginning, has been constructive. The miner digs his ore and he gives the metal to art, to industry, and to commerce. The nature of our business is destructive only in that we deal with a wasting asset. That should be a source of great pride to those who belong to the profession. But unfortunately, the product of our mines, our smelters, and our re- fineries does not always go to constructive purposes. There are times when, in the administration of the affairs of men, our product chiefly goes to purposes which are destructive. When we look upon the panorama of horror that is being enacted throughout the world today, we wonder whether any effort toward the development of civilization and culture and education and well-being has been worthwhile. We are appalled to see the things that have been developed, through the application of science, toward progress and efficiency, now used for the catastrophic destruction of those things which are the most valuable that man has built. We must find hope that this is but an episodic thing; that it must, in the infinite wisdom of the Almighty, usher in a period of peace and progress, of civilization and development that will make man's existence upon earth worthwhile.

Jan 1, 1941

By Richard Kunter

INTRODUCTION Additional work has been done on the CIP circuit at Creede, and a brief description of this work is presented in this paper. DREDGE The original dredge for the Bulldog was built by Al Hack, Inc. of Denver. The dredge cutter head is mounted on a boom made of 6-inch diameter pipe which is raised and lowered by a cable-pulley system. Maximum cutting depth is 8 feet. Slurry from the dredge flows through a floating 6-inch diameter pipe supported on 55-gallon drums which runs from the dredge to the shore and then to a trash screen and pumping system. See Figures 1 and 2. The cutter head, suction pump, winches for dredge movement, and all other operations are controlled from a small operations house located toward the rear of the dredge. All of the basic dredge equipment is mounted on a chassis about 8 ft x 16 ft in size. Additional buoyancy was originally provided by sealed 55-gallon drums supported along the sides of the chassis by a small wooden framework. Additional framework and barrels on the front of the chassis on either side of the cutter boom provided additional stability, particularly when digging in hard material. The dredge was quite stable, but two problems were apparent. For one, it could have been sunk by someone from the shore firing a rifle into all of the barrels. In prime deer-hunting and sportsman country

Jan 1, 1983

By B. A. Rogers, K. O. Stamm

BECAUSE it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,1 which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has developed recently concerning the reversibility of the transformation. From thermodynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912° for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9180 and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rates of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°°C. and concluded that a change occurs reversibly between 907° ± 3° and 9100 ± 3°C., probably between 907° and 910°C. Wells, Ackley, and Mehl6 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, '1/2°, and 1/8°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909.5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien elements were low enough, the A3 transformation would be completely reversible at 909.5° ± I°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By M. K. Yen

The distortion of crystal structures referred to as "biege gleitung",1 "local curvature"2-4 and "deformation bands"5,6 is believed to be an unavoidable characteristic of deformed single crystals. The presence of asterism on Laue photograms of Al single crystals either deformed by pure shear7 or extended in a condition relatively free from the grip effect2 indicates strong evidence substantiating this point of view. The type of localized bending described in connection with the bending test of Al single crystals by Yen and Hibbard8 could conceivably exist either microscopically or submicroscopically in all types of deformation. The purpose of this note is to extend this idea to the postulate of a hypothetical "microbending site," as applied to the mechanism of slip in a general sense. The mosiac structure, as postulated by Darwin,9 is that crystals were actually composed of small blocks which have a linear dimension 10—4to 10-6 cm on the edge and deviate from each other by an angle of about one-tenth of a degree. The following discussion is based on the assumption that when slip is propagated from one mosaic block to the adjacent one, bending of the lattice at the region of their boundary is produced in order to maintain the continuity of the gliding process along a certain slip plane. Consider a two-dimensional diagram of two ideal mosiac blocks on the cross-section perpendicular to the slip plane and containing the active direction of slip. When an external force is applied, the localized bending or "microbending site," would be generated at the region as illustrated in Fig 1A at point B. A schematic diagram of a "microbending site," generated at a mosaic boundary, is illustrated in Fig IB. It may be seen that once the curvature of the bending site reaches sufficient magnitude, the interaction force encountered by pairs of atoms symmetrical with respect to the center of the bending is equal but opposite in sign. Consequently, the overall energy required to displace the atoms near the center is approximately zero.10"12 Based upon the finding that the misalignment between two mosaics is 0.1 degree,9 the assumption is made that "microbending sites" may possibly exist in the region where one plane will have one more row of atoms than an adjacent plane. It is probable that the origin of the bending site will be where the distance between two mosaic boundaries is "2d" as shown in Fig 1A at point B, where " d" is the interatomic distance. Thus, the distance between two "microbending sites" is in the range of about 600 interplanar spacings. In the case of aluminum, the spacing between two octahedral planes is about 2.33 A. The distance between two bending sites will be approximately 2.5 X 10"5 cm. It is interesting to note that according to Woods13 these values approach closely the size of the domains of a cold-worked metal whose minimum

Jan 1, 1950

By Kehsin Kuo

DIE steel with 1.47 pct C, 0.42 pct Mn, and 8.22 pct W contains Fe,C and WC in the annealed state and WC embedded in a martensitic matrix in the hardened state (quenched from 800°C). The presence of a large amount of undissolved angular WC carbide particles makes this steel extremely wear-resistant. However, the WC carbide begins to dissolve in the austenite when the heating temperature is raised above 1000°C, but this solution process is still not complete at 1250°C although partial melting has already taken place at the austenite grain boundaries. At 1325 C, this steel contains austenite and liquid metal but no WC carbide, Fig. 1. On quenching into brine, the liquid metal solidifies into a constituent which etches differently from the austenite-martensite matrix. This constituent appears lighter than the matrix at the 1250°C stage when etched with 2 pct nital but darker in Fig. 1 when etched with Murakami's reagent. Such a constituent has also been found in burnt tungsten high speed steels. This constituent has been isolated from the matrix by anodic dissolution in a 5 pct HC1 electrolyte and was found by the X-ray powder method to be iso-morphous with &manganese, Table I. The agreement in line intensity between these two phases indicates that there is no ordering in this new phase. The calculated cube edge of this phase is 6.395A, somewhat larger than that of ß-manganese (6.30A). Besides this phase, the anodic residue also contains free carbon from the matrix and amorphous WO,, although the X-ray powder pattern of the residue shows the presence of only this phase. This makes it impossible to determine directly the composition of this phase from the residue. Attempts to prepare an alloy containing only this phase have hitherto been fruitless. The following experiments serve to show that this phase can only be obtained by drastic quenching from the liquid state and that its tungsten and carbon contents must be lower than those in the Fe,W,C carbide. On air cooling from 1325oC, the liquid metal solidifies into a eutectic consisting of austenite and the Fe3W3C carbide. The nature of this dark-etching Fe3W3C has also been ascertained by X-rays. This eutectic becomes coarser on furnace cooling. The solidification of a specimen cooled for 5 min from 1325" to 1200°C and water quenched is still not complete and the fine eutectic is formed during the quenching. Since this new phase can be replaced by a eutectic of austenite and the Fe,W,C carbide, its composition must lie somewhere between the latter two phases. The special features of this phase are: 1—it can only form directly from the liquid state by drastic quenching and 2—it is a ternary phase of iron, tungsten, and carbon. The ß-manganese structure of this phase is also interesting. In the Periodic Table, iron and tungsten lie on opposite sides of manganese; a certain combination of these two elements, in the presence of carbon, may have average properties similar to those of manganese. It has already been established that the x phase, a ternary one of iron, chromium, and molybdenum, has the a-manganese structure."' A similar phase has also been found in the ternary system Fe-Cr-W and in the following binary systems: Re-Cb, Re-Ta, Re-Mo, and Re-W.6 References 1 G. D. Preston: Philosovhical Magazine 11928) 5. 7th Series, p. 1207. - K. W. Andres: Nature (1949) 164, p. 1015. 35. G. McMullin, S. F. Reiter, and D. G. Eberling: Trans. ASM 11954) 46, p. 799. ' J. S. Kasuer: Acta Metallurgica (19541 2, p. 456. • H. J. Goldschmidt: Trans. ASM (19541 46, p. 807. P. Greenfield and P. A. Beck: Private communication.

Jan 1, 1957

By J. W. Edington

THE Hopkinson bar has become a popular technique for the measurement of the mechanical properties of materials deformed at high strain rate. Maximum use of the equipment is made in the arrangement first used by Kolskyl in which a short compression specimen is sandwiched between two pressure bars and is loaded by a single pulse travelling through the system. The pressure bars are used both to apply the load to the specimen and as transducers to obtain continuous strain-time histories of three pulses, incident on, reflected, and transmitted by the specimen. The data measured by the pressure bars can be analyzed in terms of the stress/strain behavior of the specimen.2'3 However, one of the assumptions of the analysis of the observed pulses is that the total stress and total strain do not vary significantly from point to point within the specimen at any given instant during the deformation process. Although this assumption is generally justified for very short disc-like specimens2 the situation is uncertain for larger specimens. For example, at small plastic strains (-0.01) Hauser et al.2 have some evidence of small flucations in the total stress within the crystal during deformation, even in relatively short aluminum specimens. In addition, Karnes4 has shown that the plastic strain, and by inference strain rate, is different at each end of a compression specimen tested in a Hopkinson bar, although the length of the specimen was not specified. Recently, the mechanical properties and the dislocation substructure have been investigated in single crystals of columbium5 (length 0.25 in., diam 0.19 in.), and copper6 (length 0.5 in., diam 0.5 in.) deformed at high strain rates. As part of this research program the assumption that the plastic strain is constant throughout the specimen has been checked by measuring the total dislocation density as a function of position in the specimen. Compression specimens of the same orientations and dimensions were tested as described previously5,6 sing a split Hopkinson bar. Since any discontinuity in strain distribution is most likely to arise during the initial stages of deformation the investigation was performed on specimens deformed to plastic shear strains of 0.054 (copper) at a strain rate 1.2 x l03 sec-1, and 0.06 (columbium) at a strain rate 1.5 X l03 sec-1. The orientation of the single crystals is shown in Figs. 1 and 3. Thin foils were taken parallel to the most highly stressed slip plane, i.e., (111) in copper and (011) in columbium, using conventional disc techniques. The dislocation densities were measured using first order reflections with compensation for invisible dislocations.5'6 In the copper single crystals the discs were randomly distributed throughout the cross section of the specimen. However, the dislocation density obtained from each disc was plotted vs the disc positions relative to the ends of the specimen. The results for the copper specimens are shown in Fig. 1. Clearly the dislocation density is constant throughout the main portion of specimen within the experimental error. The error bars on the dislocation densities correspond to a shear strain variation of 0.015 on the basis of previous measurements% ± of the rate of increase of dislocation density with strain in copper single crystals of the same geometry. Thus within this experimental error the plastic strain can be concluded to be constant within the specimen and the assumptions used in the analysis of the stress/time curves are therefore reasonably valid. The higher measured dslocation density near the impact end and the lower dislocation density at the bar end of the copper specimen is in agreement with the results of Karnes4 who showed that this strain/time curve rose to a maximum more rapidly at the impact end compared with the bar end. Hauser et al.2 have also pointed out that at small plastic strains (-0.01) the strain at the impact end of the specimen may be greater than that at the bar end. Thin foils taken from different points within the columbium single crystals demonstrated that the dislocation density could vary significantly within the specimen, see Fig. 2. Large areas of some thin foils up to 30 µ sq contained very few dislocations, see Fig. 2(a). However, in other parts of the compression specimen dislocation configurations like those shown in Fig. 2(b) existed over large areas (-30 µ sq). As a result, when the average dislocation density in a thin foil is plotted as a function of the position of the thin foil relative to the ends of the specimen, considerable scatter is observed, see Fig. 3. In this material then, the local dislocation density, and consequently the

Jan 1, 1970

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of break- age in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By W. A. Selvig

BY plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Com-mittee on Coal Classification. This scheme was sponsored by Sub-committee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic.. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as follows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group, 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. , The lignitic class of coal was divided into two groups both below 8,000.B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By ALFRED D. FLIWN

ENGINEERING COUNCIL is not "about to die," as some persons are saying. Through a natural and foreseen reorganization, Council is entering a new stage of existence with enlarged power for usefulness. Its early constituents have made it possible for many more of their fellow engineers and men of other technical vocations -to take a- share in its activities, responsibilities and support. A new organization is being set up, but it is really a new embodiment of the same spirit of service. Another step is being taken toward the full acceptance by the technical professions of their obligation to the public and to one another for those services which can -be rendered only through effective organization. A brief retrospect is timely. Engineering Council was established in the spring of 1917, as a department of United Engineering Society in response to requests of its Founder Societies. .It followed various attempts of these societies to deal through joint committees with public questions affect¬ing engineers -and with inter-society affairs. These attempts had very limited results. In the new by-laws adopted by United Engineering Society, the purposes and-powers d-powers of Engineering Council were thus defined: "To provide for convenient cooperation between the four Founder Societies, for the proper consideration of questions- of general interest to engineers and to the public, and to provide the means for united , action upon questions of common-concern to engineers.

Jan 1, 1920

By Harold A. Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand- book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By M. E. Grimes

A method of predicting uranium extraction rate in underground bacterial leaching of as-blasted ore has been developed. The method is based on the hypothesis that extraction is directly proportional to the volume of a piece of ore that is penetrated by the leaching agent, and that each piece of ore, regardless of size, has been penetrated radially from the external surface to the same depth at a given leaching time. Consequently, given an initial size and assay distribution, extraction should be predictable for a given penetration. Two laboratory bacterial leaching tests under simulated stope leaching conditions were carried out for a periods of 89 and 96 weeks. On completion, the residual ore was screened and analyzed. The information so obtained was employed to provide an elapsed time base for the penetration model, from which predictions of future extraction were made. The finding of solubilized uranium trapped within apparently sol id ore pieces was unexpected. However, it is not recoverable except after crushing, and hence does not affect calculations of underground leaching .

Jan 1, 1974

D. M. Riordan has been appointed a member of the Institute Com¬mittee of the Engineers' Reserve Corps movement. Our Committee, therefore, now consists of Henry S. Drinker, Chairman, Messrs. Arthur S. Dwight, Warren A. Wilbur and D. M. Riordan.

Jan 1, 1916

By William E. Hughes, Roderick K. Davey

The objective of this chapter is to review and discuss interpolation techniques commonly in use in the mining Industry today, including simple examples. This chapter will not attempt to compare the relative accuracy of each technique as this subject has adequately been covered by several authors (Knudsen and Kim, 1967; David, 1974; and Barnes, 1979) When appropriate, methods will be compared relative to the results of simple examples and computational ease. The examples presented are based on metallic deposits. The techniques, however, are not restricted to metallic deposits and can generally be applied to nonmetallic ones. The purpose of interpolation, as applied to a mineralized deposit, 1s to extend the knowledge of the grade and geology of localized samples to an estimate of the grade and mineralogy of a larger block of ground or even an entire deposit. The word interpolation means to compute values between given values and is limited to that region between the known values. The distinction between interpolation and extrapolation is important and must be adhered to in the application of these techniques in general, the interpolation must be limited to the area enclosed by verified samples. The methods being discussed can be broadly broken into three categories. ( 1 ) geometrical methods, (2) distance weighting methods, and (3) geostatistical techniques.

Jan 1, 1979