Search Documents

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

The Garfield plant of the American Smelting & Refining Company is situated about seventeen miles west of Salt Lake City, on the Los Angeles & Salt Lake Railroad, and has freight service by the Denver & Rio Grande Western. Western Pacific and Bingham & Garfield Railways. The site lies between the picturesque Great Salt Lake, with its mountain islands and the northern point of the Oquirrh Range, which forms the western boundary of the Salt Lake Valley.

Jan 1, 1925

By E. S. Hutchinson

The subject of the influence of coal-dust in mine-explosions has received considerable attention both in England and on the continent of Europe, but until the recent disaster at Pocahontas, Va., it seems not to have been of special interest to engineers in this country. The reason, perhaps, is that most of our bituminous mines are worked by short shafts, slopes and drifts; few have been specially dry; and the explosions that have occurred could readily be traced to fire-damp with 110 complicated circumstances. The object of the present paper is to bring together, for the convenience of members of the Institute, the principal English opinions upon this important subject. Messrs. Lyell and Faraday, in their report to the Home Secretary," in England, on the Haswell Colliery explosion in 1844, seem to have been the first to point out that dust fed the flame originating in a

Jan 1, 1885

By John H. Hall

The Frémont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about # by 6 by about 16 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Frémont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. In testing coupons cut from castings heat treated by quenching and annealing, attention was drawn to the wide variations in the value of the Frémont test of specimens cut from different parts of the coupon. The latter was of the form and dimensions shown in Fig. 1, and Fremont test pieces were cut from two parts of this coupon, marked A and B in that figure. The results of the tests are shown below, tests A and B in each instance being from the same coupon: A. B. A. B. Coupon. Kilogram- Kilogram- Coupon. Kilogram- Kilogram- meters. meters. meters. meters. 1,........ 12.0 12.5 9,........ 27.5 32.5 2,........ 11.0 32.5 10,........17.5 31.0 3,........ 11.5 30.0 11,........ 14.5 31.0 4,........ 20.0 33.0 12,........ 15.0 27.5 5,........ 17.5 33.0 13,........ 19.0 30.0 6,........ 17.5 20.0 14,........ 17.5 25.5 7,........ 17.5 13.0 15,........15.0 30.0 8,........ 10.0 30.0

Jan 1, 1914

R. W. Guard (General Electric Co., Schenectady)— The method of fractional replication discussed by the author has proven very valuable to us in applied research connected with alloy and process development where many of the same experimental difficulties exist. Several of our experiences may be of assistance to those who want to apply the method in these fields. Contrary to the author's observation that interactions are rarely significant, we have found in a number of cases that first order interactions exist which are significant and metallurgically important. Because of this difference there are two further precautions which should be taken in order to minimize the difficulties from this point. First, in evaluating the importance of

Jan 1, 1957

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By Henry M. Howe

The natural effect of large ingot-size should be to increase segregation. I have previously pointed1 to the excessive segregation in many large ingots as tending to confirm this, but I have shown that in case of ingots less than 16 in. square this expected effect of ingot-size is liable to masked by that of Note.—The "maximum enrichment" of each ingot, i.e., the excess of the richest spot over the average of the whole ingot, is first calculated in percentage of that average. The average of the maximum enrichment of the several ingots of a given group is the abscissa in Fig. 1. The number beside each spot tells the number of cases which that spot represents. FIG. 1.—Influence of Ingot-Size on Maximum EnrichNent in Steel Ingots. other variables. Under these conditions we should expect that, if large ingot-size really does tend to increase segregation, this effect would be shown by taking the average of large numbers of cases, so that the effects of these other variables might off-set and cancel each other.

Jan 1, 1910

By I. R. Kramer

The stress associated with the surface layer was deter-minedfor iron and molybdcnum. These measurements show that the surface layer plays a very important role in the plastic deformation of bcc metals. From the relationship between strain arui the surface layer stress and the back stress imposed by the internal obstacles, it is Proposed that the term of of the Hall-Petch equation is related only THE large number of studies on plastic flow of bcc metals have failed to delineate clearly the nature of the obstacles influencing dislocation movement. Since there have been numerous articles which have reviewed the mechanisms proposed to explain various aspects of plastic flow of bcc metals (for example, conrad1 and Keh and weissmann2), no attempt will be made here to discuss their conclusions. However, it should be to the surface stress while the term Kfd is the stress required to move dislocations through internal obstacles. Further, it was possible to derive the well-known empirical equation C = , and it is shown that the terprz a is comprised of two terms: a term Cs associated with the surface layer stress and Ci related to internal dislocation obstacles. pointed out that in all of these publications it has been tacitly assumed that plastic flow occurred uniformly throughout the cross section of the specimen (except, of course, for the Luders band region), It has generally been further assumed that the nature and distribution of the obstacles opposing the motion of dislocations are of the same type throughout. The role of the surface layer in bcc metals has not, as yet, been considered even though its role in fcc metals has been shown clearly to be of primary importance.3-5 Investigations on fcc metals have shown that at the onset of plastic deformation a surface layer acts to

Jan 1, 1968

By M. C. Lavine, H. C. Gatos, R. S. Mroczkowski

The structure of GaAs-Ge heterojunctions prepared by a back-melting process was studied by X-rav diffraction, melallographic, and electron-micro-analyzer techniques. The boundary region between the GaAs and the germanium was found to consist of a four-layered band. A discontinuity between the two inner bands was brought about by solidification occurring simultaneously from the GaAs and the germanium side. The junction material OH either side of the central discotinuity was found to have grown as a single Crystal with the orientation of the parent substrate. It was found essential to determine the GaAs-Ge phase diagram. This was accomplished by a series of alloys containing 0 to 40 wt pet GaAs. Over this range the diagram is a simple eutectic with the eutectic point at 74 wt pet Ge and 845 C. The limiting- solubility of Coils in germanium was found to bc less than 5 wt pet. The Kossel divergent-beam X-ray technique was used to study orientation relationships across the boundary lager. A great deal of effort has been recently expended on the electrical properties of heterojunctions. Little attention, however, has been given to the metallurgical variables which may be of importance in the formation of the junctions. The present work was undertaken to investigate some of the more pertinent metallurgical aspects of interface-alloyed GaAs-Ge heterojunctions. Such parameters as solidification processes, composition gradients, orientation effects, and the accommodation of crystal structures have been the objects of study in this program. EXPERIMENTAL PROCEDURES Phase Diagram. The phase diagram of the GaAs-Ge pseudobinary system was determined by means of cooling curves. A Bridgeman furnace was employed with the center section maintained at 1200°C and the upper section at 800°C. Melts varying from 0 to 40 at. pct in GaAs content were used. Each charge was incapsulated under a two-thirds atmosphere of argon in a carbon-coated quartz tube. Five min in the furnace hot zone provided rapid melting and homogenization. The capsule was then removed to the cooler portion of the furnace. Cooling times were of the order of 3 min. The resulting homogeneous microstructure indicated that equilibrium conditions were obtained by this procedure. Formation of Heterojunctions. Rectangular parallelepiped single-crystal samples were cut with the large faces of either the (l00), (110), or (111) orientation. The remaining four surfaces were also cut to specific orientations to permit accurate relative orientation of the GaAs-Ge pairs. The

Jan 1, 1965

By Roy C. Kirkman

It is with great pleasure that I read Mr. Howard M. Wells article in the December 1978 issue of MINING ENGINEERING entitled: "Optimization of Mining Engineering Design in Mineral Valuation." Mr. Wells very adequately presents the case and point that there are a great number of variables which must be analyzed during an economic evaluation of an FUND RESOURCE, such as copper or uranium.

Jan 4, 1979

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InSb, GaSb, and AlSb were measured over the temperature range 400" to 1450°K using a diphenyl ether drop calorimeter. Smoothed ualues of the thermal properties, H$ - H:9s, have been derived and are tabulated at even temperature intervals. The heats of fusion of the three compounds were determined as, respectively, 5707 *100, 7780 * 100, and 9800 5 3011 cal per g-atorn at the determined melting points of 797" l°, 985" * , and 1330" * 5°K. The calculated entropies of fusion are, respectively, 7.16 0.12, 7.90 * 0.11, and 7.37 * 0.23 cal per deg per g-atotn. The heat capacities increase substantially on tnelting in contrast to the behauior of structurally related germanium and silicon. Deriations from the Kopp-Neumann rule are negative for solid compounds and positive for the liquid phases. Previously obsevrrd "post melting" in InSb is confirmed. The high-temperature thermal properties of 111-V compounds are presently not well-established, despite the technical importance of these semiconducting cbmpounds. Uncertainties in available heats of fusion and heat contents have seriously hampered thermo-chemical evaluations' and thermodynamic analyses of phase equilibria2"" in these systems. This paper reports results of high-temperature heat content investigations of InSb, GaSb, and AlSb measured in the range 400" to 1450°K employing a diphenyl ether drop calorimeter. Similar measurements for InAs and GaAs will be reported in a following publication.~ EXPERIMENTAL PROCEDURES Samples. High-purity samples of the compounds InSb and GaSb were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories and in the form of single crystals by Dr. A. Strauss of the M.I.T. Lincoln Laboratory. Single-crystal samples of semiconductor-grade AlSb were supplied by Dr. W. P. Allred of the Bell and Howell Research Center. Chemical analyses indicated that all compounds were stoichiometric to *0.1 at. pct, which is within the experimental uncertainties of the analyses. Samples were crushed, weighed, and encapsulated in evacuated, thin-walled, fused silica capsules. The capsules were nearly identical in external shape, 2 cm by 2 cm diam, but varied in weight due to differences in wall thickness. One sample of AlSb was contained in a thin-walled, high-purity alumina cup encapsulated in silica and used for heat content determinations of liquid AlSb. The capsule materials showed no visual evidence of reaction with any of the compounds. The sample and capsule weights are given in Table I. Calorimeter. A Bunsen-type calorimeter, similar in design to a previously described instrument6 but employing diphenyl ether (C6H5)'0 as the calorimetric substance, was used for measurements of heat contents above 300.0°K, the melting point of diphenyl ether. Heat input to the calorimeter caused isothermal melting of diphenyl ether, and the resulting increase in volume was measured by displacement of mercury from the calorimeter into a 200 cm horizontal, calibrated capillary, 1.25 * 0.01 mm diam, or into a weighed beaker. The advantages of diphenyl ether over water have been previously pointed out7 and include: i) an increase by a factor of 3.5 in sensitivity as measured by the ratio of the volume change to the enthalpy change on fusion, ii) the smaller required extrapolation from the melting point to the standard temperature of 298.17"K, and iii) the positive volume change on fusion of diphenyl ether in contrast to the contraction which occurs on fusion of ice. Diphenyl ether was purified by fractional crystallization to 99.95 mol pct as determined from the melting point depression with fraction crystallized. During assembly of the calorimeter, the ether was repeatedly outgassed under high vacuum to remove dissolved air. The calorimeter receiving vessel consisted of an 8-in.-long by 1:-in.-diam copper tube with twelve horizontal 3-in.-diam radiator "fins" for dissipating heat to the surrounding mantle of diphenyl ether. Before forming the mantle the chamber surrounding the receiving vessel contained 3300 cu cm of liquid diphenyl ether above 250 cu cm of mercury which was

Jan 1, 1970

By Benjamin C. Allen

The surface tensions of liquid chromium and manganese were determined by a modification of the dynamic drop-weight method and found to be, respectively, 1700 * 50 and 1100 * 50 dynes per cm at their melting points. Molten drops were formed LITTLE is known about the surface tension of liquid chromium and manganese, even though they are technologically important metals and widely used in steelmaking. In the past, direct determinations have been hampered by their high reactivity on the lower end of a vertically held rod inductively heated under argon. The technique essentially reproduced surface tensions reported for liquid nickel and zirconium using static drop-shape methods. and vapor pressure. In this work, surface tensions were measured by the drop-weight method, using induction heating under argon. EXPERIMENTAL WORK Chemical analyses of rods used are given in Table I. Chromium rods were prepared from iodide-process crystals which had been are-melted, hot-extruded, warm-swaged, and centerless-ground.'

Jan 1, 1964

By J. L. Jernegan

IN a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of Western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaft-furnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the various metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

Jan 1, 1876

By M. Cohen, R. T. Howard

The purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature transforrnations have been summarized recently by Troiano and Greninger.' Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation (Mg) during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transformation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metal-lographic3 and dilatometric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Stewardi have shown that the Greninger-Troiano metallographic technique8 may be used not only for M, determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below M, in fourteen commercial steels. In the present paper, the Greninger-Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M., thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. Experimental Details Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M. temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1949

By M. Cohen, R. T. Howard

The purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature transforrnations have been summarized recently by Troiano and Greninger.' Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation (Mg) during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transformation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metal-lographic3 and dilatometric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Stewardi have shown that the Greninger-Troiano metallographic technique8 may be used not only for M, determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below M, in fourteen commercial steels. In the present paper, the Greninger-Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M., thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. Experimental Details Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M. temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1949

By J. P. Savely, D. E. Nicholas, R. D. Call

Progress in the technology of slope design over the past 15 years now permits the selection of rational slope angles if suitable data on geology, hydrology, and rock properties are available for a specified project. Although a full-scale slope design study remains the best course of action, there are situations where an extensive study is not feasible due to time or budget constraints. Two typical examples are: (a) selecting pit slope angles for a preliminary feasibility study at the exploration stage; and (b) coping with a slope failure in an operating mine. In both instances, slope angles must often be chosen on the basis of data that are currently available or can be readily obtained. All too often during exploration programs, a feasibility study is initiated shortly before the decision deadline to drop the property or proceed to purchase. If the only existing data at this point are a few cross-sections at odd angles showing ore and waste contacts or a dog-eared map of the surface geology, there may not be time to collect and organize sufficient information for the design of slope angles. On the other hand, if during the drilling program geologic cross-sections were constructed and the structural data compiled in tabular form, rational slope angles could be computed within the allotted time.

Jan 4, 1977

By Robert J. Linney

In the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the "21" Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. I, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously devel-oped sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel te footwall and hanging wall to make a bench, spdlling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore, by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1946

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945