Search Documents

By H. S. Drinker

THE first discovery of zinc 011 the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Rapper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded 011 the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. I t is supposed that the zinc was originally disseminated through the

By John R. Wynnyckyj

Results of correlations between strength-development and sintering shrinkage occurring during induration are presented. A mathematical treatment of the shrinkage kinetics is, next, given and is based on the use of semi-empirical equations. The discussion stresses the significance of kinetic constants and activation energies in the assessment of iron ore concentrates for pelletizing and induration. Next, starting with the assumption that there is a need for parameters to characterize the iron-ore concentrates and relate these parameters to shrinkage-kinetic constants and balling behaviour, results of compaction measurements and pore structure characterization (mercury porosimetry) are presented and discussed.

Jan 1, 1977

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period August 1, 1916 to September 10, 1916: C. L. Cantley, New Glasgow, N. S. H. M. La Follette, La Follette, Tenn. D. A. Cowell, Columbus, Ohio. Montrose L. Lee, Montevideo, Uruguay. Alexander Deussen, Houston, Texas. V. H. McNutt, Billings, Mont. Chas. E. Dutton, Goldfield, Nev. J. W. Maller, New York, N. Y. H. S. Emlaw, Grand Haven, Mich. Edwin W. Mills, Tul. Mi Chung, Chosen, J. M. Gillette, Swatsburg, N. Y. Korea. E. Gorilla, San Antonio, Texas. Francis R. Pine, Elizabeth N. J. Bertram Grant, Kingman, Arizona. Frank A. Ray, Columbus, Ohio. Ruger W. Hay, Bisbee, Arizona. John A. Rice, El Paso, Texas. C. F. Hendricks, Cobalt, Ontario. W. E. Rice, Ringwood Manor, N. J. Stanley C. Herold, San Jose, Cal. W. H. Staver, Lynchburg, Va. Lloyd Hoffman, Pottersville, N. J. Ralph H. Sweetser, Easton, Pa. Charles Hunter, London, England. Kirby Thomas, New York, N. Y. G. Jansen, Benkoelen, Sumatra. Henry Traphagen, Union Hill. T. H. Jenks, Oatman, Arizona. M. M. Valerius, Tulsa, Okla. Warren jenny, Chanaral, Chile. Wilfrid B. Wainewright, London, Eng. Walter A. Barrows, Jr., of Brainerd, Minn., has been elected president and general manager of the Thomas Iron Co., Easton, Pa., to succeed Ralph H. Sweetser, whose resignation of several months ago becomes

Jan 10, 1916

By K. P. Gupta, P. A. Beck, N. S. Rajan

By determining the a phase boundaries in the following ternary systems: V-Fe-Si (at 1175oC), V-Co-Si (at 1175°C), V-Ni-Si (at 1175oC), Cr-Mn-Si (at 1000°C), Cr-Co-Si (at 1175°C), Cr-Ni-Si (at 1175°C), V-Fe-A1 (at 1175°C) and Cr-Co-A1 (at 1175°C), it was found that Si exerts a stabilizing effect on these a phases, while A1 tends to destabilize them. Si atoms in solid solution occupy sites D in the a structure, The co/ao ratio increases with increasing Si-, Mn- or Fe-content. The volume of the unit cell decreases with increasing Si-content. THE stabilization of certain metal silicides (the Nowotny phases) by the addition of relatively small

Jan 1, 1961

By M. Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molybdenum, lead, zinc, and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high, the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper prices; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1984

By Charles D. Hoyt

T IME studies and cost accounting were combined to increase the efficiency of the overall mining method and thereby reduce costs at the Titania mine of the National Lead Co. in southern Norway about 70 miles southeast of Stavanger. From these studies a more effective drilling system was developed, standards were adopted for setting base pay rates, shrinkage stoping was abandoned for open stoping, a new mechanical loading chute was adopted, and the loading and haulage system was changed. Ore minerals at the Titania mine are ilmenite and magnetite; gangue minerals are plagioclase and hyperstene with accessory minerals of biotite, pyrite, chalcopyrite, and spinel. The average content of the ore is 17 pct TiO2 and from 20 to 25 pct iron. The ilmenite crystals contain microscopic lamels of hematite, making it impossible to obtain a high TiO2 content in the concentrate. An ilmenite concentrate with 44 pct TiO2 and 36 pct Fe, and a magnetite concen-

Jan 9, 1950

By L. L. Karafiath, S. G. Vick, E. A. Nowatzki

Computer analyses of the trafficability of copper mine tailings by four different commercially available BWEs were performed. A mathematical model incorporating the tailings' Coulomb strength parameters and the vehicles' geometry and operational characteristics was used to study the vehicle terrain interaction. The computer output provides the maximum tractive force (net drawbar pull) that each BWE can develop for given tailings conditions without bnngzng about a state of plastic failure in the tailings. Estimates of sinkage are also provided. The theoretical results for the BWEs and tailings studied compare favorably with the operating experience of similar BWEs used for remining gold tailings in South Africa. This lends some confidence to the validity of the mathematical model. The results of such analyses may be wed to evaluate, on a relative basis, which of a number of different machines would perform better than others under given conditions of a tailings deposit.

Jan 1, 1982

By S. K. Ruggieri, R. A. Jankowski

Airborne respirable dust levels on longwalls can be reduced if operators approach the dust control problem in a logical and fundamental manner. This can be accomplished through the proper application and continued use of effective dust control techniques. The Bureau of Mines is currently assessing the effectiveness of longwall dust control techniques in use today to provide mine operators with guidelines for selecting the most appropriate control technology. This paper presents a fundamental approach to the problem of shearer dust control. Three dust control techniques to be discussed are: deep cutting/increased pick penetration for reducing the amount of respirable dust generated; drum water sprays/improved water supply system to suppress the amount of airborne respirable dust; and improved external water spray system, the “shearer-clearer, "to push the dust close to the face. The techniques have been evaluated infield trials and have been shown to be both practical and effective in applications to control shearer generated dust.

Jan 1, 1985

By John McCaslin

ONE of the most common technical terms in the U. S. today is automation-a word not listed in the 1946 dictionary. The influence of automation on the national economy has been tremendous. It has even been the subject of congressional investigations. Automation, writes Aronson, substitutes mechanical, hydraulic, pneumatic, electric, and electronic devices for human effort and decision? Automatic devices and instruments are used extensively in some industries, but many others have yet to take full advantage of these great discoveries. The petroleum industry has been a leader in using automatic controls-some refineries are almost completely controlled by automatic devices. The field of geophysics is entirely dependent on instruments and has progressed at almost exactly the same rate as improvements in instrumentation. In metallurgy and mineral dressing use of instrumentation is increasing very rapidly. Mining engineers throughout the country are beginning to think in terms of instruments and controls.

Jan 3, 1958

By Cyril Wells, Robert F. Mehl

The purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2o C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made2. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsenl that variations as great as 30' C. exist in the reported data on the A3 temperatures in iron-carbon alloys. Fortunately, the Aa temperature in pure iron is now known to be 910" C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato5 on both hypoeutectoid and hyper-eutectoid steels. Esser made a dilatometric and magnetic study of iron and iron-carbon alloys containing 0.06 to 0.86 per cent C, for which a high purity is claimed. Presumably the electrolytic iron was reasonably pure, but the alloys contained considerable impurities, on the average totaling 0.35 per

Jan 1, 1937

ALTHOUGH the refining period of the heat is generally defined as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed. semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1951

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By E. H. Dix

All commercial aluminum contains small percentages of copper, iron, and silicon as unavoidable impurities. The purest metal obtainable commercially, special grade high purity ingot, contains a maximum of 0.50 per cent. impurities of which the usual minimum amount of copper is 0.01 per cent.; silicon, 0.12 per cent.; and iron, 0.20 per cent. This grade is too costly for most purposes. The two standard grades, Nos. 1 and 2, containing a minimum of 99.0 and 98.0 per cent. aluminum, respectively, are more generally used. Other grades of secondary aluminum often contain as high as 3 or 4 per cent. of impurities, which include 1 per cent., or more, of zinc. Specifications for high-grade aluminum-casting alloys generally allow a maximum of 1.7 per cent. for total impurities. The S. A. E. Specification No. 33, which is intended to cover alloys made from secondary aluminum ingot, gives the iron maximum as 1.5 per cent. and the maximum for silicon (including manganese and tin) as 0.75 per cent. The effect of even relatively small amounts of impurities on the physical properties of ingot aluminum is shown by the following cornparison of two lots of aluminum, which may be taken as representative of special grade and grade No. 2 ingot, respectively. AnalysEs Special Grade, Gbade No. 2, Per Cent. PeR CBnt. Copper................................. 0.01 0.32 Silicon................................. 0.12 0.32 Iron................................... 0.42 0.82 Aluminum.............................. 99.45 98.54

Jan 1, 1923

By E. H. Dix

All commercial aluminum contains small percentages of copper, iron, and silicon as unavoidable impurities. The purest metal obtainable commercially, special grade high purity ingot, contains a maximum of 0.50 per cent. impurities of which the usual minimum amount of copper is 0.01 per cent.; silicon, 0.12 per cent.; and iron, 0.20 per cent. This grade is too costly for most purposes. The two standard grades, Nos. 1 and 2, containing a minimum of 99.0 and 98.0 per cent. aluminum, respectively, are more generally used. Other grades of secondary aluminum often contain as high as 3 or 4 per cent. of impurities, which include 1 per cent., or more, of zinc. Specifications for high-grade aluminum-casting alloys generally allow a maximum of 1.7 per cent. for total impurities. The S. A. E. Specification No. 33, which is intended to cover alloys made from secondary aluminum ingot, gives the iron maximum as 1.5 per cent. and the maximum for silicon (including manganese and tin) as 0.75 per cent. The effect of even relatively small amounts of impurities on the physical properties of ingot aluminum is shown by the following cornparison of two lots of aluminum, which may be taken as representative of special grade and grade No. 2 ingot, respectively. AnalysEs Special Grade, Gbade No. 2, Per Cent. PeR CBnt. Copper................................. 0.01 0.32 Silicon................................. 0.12 0.32 Iron................................... 0.42 0.82 Aluminum.............................. 99.45 98.54

Jan 1, 1923

By R. Hadfield

Last year this institute was good enough to accept some remarks by the writer regarding sound steel, entitle Plant for Hadfield Method of Producing Sound Steel Ingots…

Jan 1, 1915

By Robert Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 4th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 3rd edition (1960) of Industrial Minerals and Rocks will clearly demonstrate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Re- view. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 3rd edition of Industrial Minerals and Rocks. Most of these, of course, are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 11th annual meeting in 1975, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the U.S. Geological Survey and the U.S. Bureau of Mines. The two agencies publish many reports and maps on a variety of geo- logical and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications. (New Publications of the Geological Survey, U.S. Geological Survey, Washington, D.C. 20242) and New Publications-Bureau of Mines, Publications Distribution Branch, U.S. Bureau of Mines, 4800 Forbes Ave., Pittsburgh, Pa. 15213). The U.S. Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, and 1970. Three other major series of publications by the Bureau are Information Circulars, Reports of Investigations, and Mineral Trade Notes. The latter is particularly good for news of foreign developments. A new Professional Paper No. 820 of the U.S. Geological Survey, 1973, summarizes data on the mineral resources of the entire country. The USGS, in cooperation with USBM, other Federal and various state agencies, has also prepared summary reports on mineral and water resources of given areas which include

Jan 1, 1975

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. &apos; The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By J. L. Huitt, B. B. McGlothlin, J. J. Day

Laboratory tests were made with pure minerals and actual reservoir rock samples to study the effects of hydrothermal (steam m hot water) treatments on reservoir rock properties. These tests showed that hydro-thermal treatment of many reservoir rocks can result in significant rock softening. The softening was attributed primarily to the partial destruction of dolomite and kaolinite and the synthesis of montmorillonite in the presence of excess silica. In many cases, the softening was great enough to cause considerable healing of propped fractures; therefore, a serious reduction in welt productivity could result. In other tests it was found that the addition of ammonia to a hydrothermal treating fluid in a concentration as low as 0.013 Ib/lb of water not only could prevent rock softening but could cause rock hardening. The results of X-ray diflraction analyses of rock samples showed that when ammonia was added to the treating fluid, ammonium-mica and analcite were formed instead of montmorillonite. No significant permeability damage was observed in the sandstones that were subjected to the ammonia-hydro-thermal environment; in some sandstones, permeabifity improvements resulted. INTRODUCTION As the use of steam or hot water becomes more prevalent in well stimulation methods. the need for information on the effects of such treatments on reservoir rock properties becomes increasingly apparent. Several works have been published on high-temperature changes in rock properties,&apos;,&apos; but these are more applicable to in situ combustion operations than to steam or hot water injection processes. The mineralogical literature contains many publications which report on the changes occurring with various pure minerals in hydrothermal systems. A review of this literature denotes the ease with which entirely new, crystalline mineral phases can be synthesized from other minerals in hydrothermal environments at temperatures, pressures and residence times typical of those encountered in oilfield thermal recovery or stimulation processes. Discussions of many of these experiments are given by Deer et al. Grim,&apos; Roy et al., Zen\ and Hawkins.&apos; One of the most significant of these pure mineral studies is the hydrothermal synthesis work of Levinson and Vian" in which montmorillonite was synthesized from naturally occurring minerals; i.e., kaolinite, quartz and carbonate minerals (particularly dolomite). These reactions occurred at 575F in only 2 days and at 300F in 5 days. These results may be applicable to petroleum reservoir rocks since the minerals studied were those which are commonly found in sandstones. Furthermore, the environmental conditions imposed in the studies were very similar to those involved in thermal stimulation of petroleum reservoirs, e.g., steam or hot water injection. Other studies have suggested that weak rocks could be hardened by "electrochemical induration", a process in which an electric current is applied to a clay-containing rock body. These tests can be regarded as hydrothermal treatments since they were conducted in some instances with aqueous solutions and since clay temperatures during the electrical treatment reached a maximum of about 100C. Although a number of studies of the reaction of pure minerals have been reported, very little has been published on the reactions of petroleum rock-hydrothermal systems. No work has been reported on preventing the more detrimental rock changes in rock softening which might occur during the injection of steam or hot water into reservoirs. The studies described in this paper were conducted to provide such information. EXPERIMENTAL APPROACH The laboratory tests included studies of the effect of hydrothermal treatment on core samples from several different reservoirs. The hydrothermal treatments (simulated steam treatments) were conducted with distilled water at 575F, for the most part, for periods of 2 to 6 days. This temperature level was selected because it represented that temperature which would probably prevail in several cases under consideration for steam injection projects. The core samples, as well as the pure mineral samples, were contained in high-pressure stainless steel, autoclave-type pressure vessels. The effects of the hydrothermal treatments were evaluated by measuring the penetrometer hardness, formation rock embedment strength and permeabilities of the core samples before and after the treatments (Fig. 1)&apos;" In addition, the mineralogical changes in the specimens were studied by X-ray diffraction. Concomitant with the core sample studies, the mineralogical changes were studied in greater detail by conducting hydrothermal synthesis experiments with pure minerals at similar temperature levels and residence times. For the most part, samples of finely-crushed pure dolomite.

By James Herbert Bartlett

The MANUFACTURE of Iron in the PROVINCE of Quebec. The St. Maurice Forges.—The deposits of iron-ore in the St. Maurice district, in the rear of Three Rivers, were probably known to the Indians and .Jesuits, but it is not till 1667 that any discovery is reported. The affairs of the colony were then in the control of the " West India Company," who amongst other monopolies had a right to all mines and minerals." Specimens of the iron-ore were examined in Quebec. in 1668 by the Sieur la Potardière, who reported unfavorably on them. In 1671, Louis de Buade, Comte de Frontenac, was appointed governor of La Nouvelle France ; and in the original manuscripts relating to his administration some allusion is occasionally found to the St. Maurice iron mines.? In a letter to the Imperial Government, dated 2d November, 1672, he says: "The iron mine of which I have already spoken is of great consequence. I have visited it myself, in order that I may be enabled to give a more accurate account of its nature. I am gratified to learn that another mine has been discovered in Champlain, which is much richer than the Cap de la Madelaine mine, and the ore is in greater

Jan 1, 1886

[Appalachian Petroleum Section: Chairman: Robert H. Edele, 1st V.C.: Robert Vutech, 2nd V.C.: Robert Tullis, Sec.-Treas.: Frederick T. Solomon. Meets last Tuesday of each month in Charleston, W. Va. Balcones Section: Chairman: Dr. Frank W. Jessen, 1st V.C.: Gilbert M. Andreen, 2nd V.C.: Lloyd N. Johnson, Seo.-Treas.: W. C. Vercellino. Big Horn Basin Subsection: Chairman: B. E. Yester, 1st V.C.: Robert J. Woodhall, 2nd V.C.: Herbert A. Koch, Secretary: Dean Costello, Treasurer: Thomas W. DeLong. Meets 2nd Wednesday; alternating between Cody and Worland. Billings Petroleum Section: Chairman: George O. Ellis, 1st V. C.: Robert L. Spottswood, 2nd V. C.: Robert M. Watkins, Sec-Treas.: Joseph H. Bato. Meets 5:30 p.m., 3rd Tuesday at Billings Press Club.]

Jan 1, 1961