Search Documents

By B. M. Larsen

Jan 1, 1965

By P. D. Bush, E. H. Gates, M. D. Vijayaraghavan, L. F. Engle

The process developed over the last few years by Republic Steel Corporation in conjunction with Colorado School of Mines Research Institute has been used as a basis for the conceptual engineering of full size plants. The paper will cover the equipment design criteria, equipment design itself, and the integration of the complex unit operations. There are unique features of agitation and use of gas media through- out. The paper will provide an illustrative example of the process requirements for a variety of raw material feeds. It will discuss the materials of construction approach required.

Jan 1, 1973

By R. U. Jackson

FACED with rising costs, the mining industry is looking to new methods and equipment to supply the relief necessary for profitable operation. Conveyor transportation is rapidly taking a superior position to motor tramming in underground mines because of lower installation, maintenance, and operating costs. Haulage is always a critical problem in underground mining. The ease of operation and flexibility of a haulage system can have an important effect on ultimate mining cost. With the average tenor of ores on the downgrade, larger tonnages are required for the same metal recovery. This selection of a tramming system can be the key to a successful, paying plant. Because this shift is being made at an ever advancing rate, it may become necessary to tailor mining operations to the transportation system, rather than to select a haulage system fitting set mining methods. In choosing a haulage system, the relative costs of the various methods are of the greatest importance. Adapting the mine to one or the other type of tramming is not considered in the cost analysis, and very likely would make little difference, outside of location of drifts and raises. In the cost sheet, the problem presents recommendations for a conveyor installation and a comparison of equipment, installation, operation, maintenance, and power costs are made. Under the track haulage estimate, no allowance was made for dumping equipment at the shaft pocket or bin. If this equipment was added to the balance sheet, the additional

Jan 1, 1952

By H. N. Wolcott

AMONG the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It, therefore, seemed to the writer that the case described below was worthy of record. FIG. I.-GROUND MASS OF CHALCOPYRITE (C) CONTAINING ROUNDED GRAINS OF PYRITE (P) SHOWING DIFFERENT DEGREES OF REPLACEMENT BY QUARTZ (Q), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town Mine, in Russell Gulch, and are in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy- rite, with some grains of tetrahedrite. The polished surface of some of

Jan 6, 1917

By Reno H. Sales

EVERY mine manager, mine geologist, and every prospector in the field who appraises the future of mining properties does so on the basis of a theory of ore deposition whether he recognizes this fact or not. Wherever the ultimate value of a mine or prospect is dependent upon undeveloped ore, any estimate by an engineer or geologist necessarily involves a theory of origin of the deposit. In view of these facts the importance of a thorough understanding of the genesis of ore deposits cannot be overestimated. It well may be that the greatness of our country will depend upon finding reserves of natural resources as yet undiscovered. The genesis of ore deposits offers a fascinating field for study and investigation. This is attested by the large number of geologists who have written at length on the subject. For progress made toward a better understanding of ore genesis we owe much to Kemp, Lindgren, Ransome, Vogt, Emmons, Spurr, Graton, and a host of others. Within my own experience, I have attempted to apply in practice the various concepts and theories that have been advanced by these men.

Jan 5, 1954

NEW MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10, 1916 to Mar. 10, 1916. ALLAN, FERGUS L., Min. Engr., Cons. Min. Engr., Mexico Mines of El Oro, El Oro, Mex. ARMSTRONG, EMERSON WARREN, Met.,. Mina Bibilonia, La Libertad, Nicaragua, C. A. BABB, P. A Blaisdell Coscotitlan Syndicate, Pachuca, Hgo., Mex. BANDY, PERCY J Fundicion Delicias, Calle Delicias, Mexico, D. F. BELLWALD, J. N Apartado 1488, Mexico, D. F. BILLICK, DON CARLOS, Min. Engr., Supt., Hess Gold Mines Co., Alturas, Modoc Co., Cal. BITLER, FRANK L., Cons. Min. Engr., Birkinbine Engineering Offices, Parkway Bldg., Broad and Cherry Sts.. Philadelphia. Pa.

Jan 4, 1916

ALABAMA Alabama City.-Eddy, L. Altoona.-Cain, J. America.-Foreman, J. T. Anniston.-Foster, R. N. Ashland.-Sturdevant, J. C. Bessemer.-Ball, E. M. Calhoun, F. W. Maschmeyer, W. L. McKenzle, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H, Jr. Ashton, J J.

Jan 1, 1923

By B. D. Cullity

A distribution of residual stress after plastic elongation is proposed, in which the bulk of the material is strained in compression and a very small portion in tension, This distribution is shown to account both for the X-ray observations and for the effect of plastic straining on magnetic losses in silicon steel. The regions left in compression are tentatively identified with the interiors of the sub-grains revealed by the electron microscope. THIS paper is concerned with the general problem of the nature of the residual stress which is produced in metals by plastic elongation. A particular stress distribution will be suggested which accounts for the main X-ray diffraction observations which have been made. It will also be shown that certain magnetic measurements made on silicon steel can be understood in terms of this stress distribution. X-RAY OBSERVATIONS Uniform straining of a crystal lattice (macro-strain) causes a diffracted X-ray beam to shift its position, and nonuniform straining (microstrain) causes line broadening. If a bar of metal is plastically elongated in the longitudinal x direction and then unloaded, diffracted X-ray lines are observed to be both shifted and broadened.'-= Although the observed line shift indicates the presence of macro-strain, experiments have shown that no macrostrain, in the usual engineering sense of the term, exists.5"7 For example, removal of a layer from one surface of a stretched and unloaded bar does not produce curvature in the remainder of the bar 5'7 Fig. 1 shows the variation of lattice strain in the x direction, as determined from X-ray line shifts, with the applied stress in the same direction. The curve ABC is the normal stress-strain curve of the material, AB being the elastic portion and BC the plastic. In the elastic region AB, the strain measured by X-rays, called the lattice strain, and the strain measured mechanically are both proportional to the applied stress, and both return to zero when the applied stress is removed. Above the elastic limit the lattice strain would be expected to continue to increase along the line BD. Actually, it increases less rapidly with respect to stress, or even decreases, as shown by BE. If the applied stress is then decreased, the lattice strain decreases along EF, which is parallel to AB. As a result, there is a compressive residual lattice strain FA after unloading. STRESS DISTRIBUTION. Since a stretched and unloaded bar does not contain macrostress, it follows that the observed line shift must be due to a special distribution of mi-crostress. Such a distribution is shown in Fig. 2, which shows the variation of the stress u, across a stretched and unloaded bar. The material is assumed to consist of two kinds of regions: regions C, stressed more or less uniformly in compression, comprising the bulk of the volume of the material and responsible for the observed diffrac-

Jan 1, 1963

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards' work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

Discussion of the paper of A. P. WATT, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 130, October, 1917, pp. 1476 to 1563. THE CHAIRMAN (0. M. _BILHARZ, Miami, Okla.).-Mr. Watt's reference to sorting or hand-picking of the ore in the lead district, which is being introduced at Mine La Motte, is especially interesting. I believe, from my former experience in the district, that hand-picking should be practised to some extent by all the companies in the Lead Belt. I know that a great many thousand tons containing only very small amounts of lead are passed through the mills, which, of course, is not to the advantage of milling machinery. That procedure may be Warranted at times of high prices, but I think that hand-picking should ordinarily be adopted to some extent: ERNEST GAYFORD, Salt Lake City, Utah.-On page 1525, speaking of the settling of slime previous to treatment either on slime tables or by flotation, Mr. Watt states: "The settling area allowed per ton of dry slime varies from 11 to 16 sq. ft.-an average for the district would be about 13 sq. ft. of settling area per ton of dry slime. This figure applies when the, discharge contains 20 per cent. solids." Mr. Ramsey, of the Dorr company, is here and I would like to ask him whether a settling area of 13 sq. ft. per ton of dry slime per 24 hr. is not considerably above the average area of Dorr settling tanks, and whether 20 per cent. solids is not above the general dilution for that' capacity? I should also like to know what is the general average on slimes of that character. E. R. RAMSEY, Denver, Colo.-An allowance of 13 sq. ft. per ton does seem rather large. I am not familiar with the settling characteristics of the dolomitic gangue, but as an average over the country, I should say that 6 or 7 sq. ft. would be nearer correct for discharge at that consistency. L. A. DELANO, Bowie Terre, Mo.-We have had an opportunity to try our tanks at the highest capacity, and-find that by thickening the slime to 30 per cent. solids we average 12 sq. ft. per ton of dry slime. ERNEST GAYFORD.-DO you find any definite ratio between the thickness of the discharge and the settling capacity of the tank? Do you consider that the tank has a larger capacity if the discharge is 3 to 1 than if it is 50 per cent. solids? L. A. DELANO.-I think it has greater capacity with the thinner discharge. It depends a good deal on the density of feed to the tanks; in our case the feed contains 2.5 per cent. solids.

Jan 1, 1918

By L. R. Gremillion, G. H. McClellan

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commerical deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained four to ten mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. Samples contained varieties of francolites, fluorapatites, and mixed hydroxyfluorapatites. The apatite compositions calculated from chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2- for (PO4)3-, and the P205 contents of the apatites ranged from 35.1 %for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate ore, it is necessary to consider the dissolution behaviors of different mineral phases during acidulation and their possible effects on chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1982

By L. W. McKeehan, W. C. Elmore

THE magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter' first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel' single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. SPECIMENS The following list describes the specimens used in the present investigation. DESIGNATION DESCRIPTION A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which he gave the following typical analysis: C, 0.05; P, 0.038; 5, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick.

Jan 1, 1935

ALASKA Established November 19, 1947 Meets fourth Monday of each month at Fair¬ banks, Alaska J D CRAWFORD, Chairman BRUCE I, THOMAS, Vice-Chairman C D JERMAIN, Vice-Chairman for Southeastern Alaska EARL H BEISTLINE, Secretary-Treasurer Box 265, College, Alaska

Jan 1, 1952

By Petri Bryk, John Ryselin, Rolf Malmstrom, Jorma Honkasalo

THE theoretical possibilities for the realization of flash smelting have been known for a long time. Calculations concerning the same can be found in previously published literature,1 and suggestions for its accomplishment in practice are described in patents on the subject. Likewise a smaller number of practical test results are known. Autogenous smelting is closely connected with flash smelting, since in flash smelting techniques it is possible to use the heat evolved by oxidation of the sulfides for the smelting process to such an extent that under certain conditions smelting can proceed without additional fuel. However, in the event that insufficient heat is available from the oxidation of the sulfide concentrates, then additional heat may be supplied by preheating the air, using oxygen enriched air, on burning additional fuel with the concentrate.

Jan 6, 1958

By C. K. Donoho

SILICON is used in almost all commercial steels; up to about 0.20 pct in killed wrought steels and 0.50 pct in steel castings. Above about 0.50 pct in wrought steels and 0.70 pct in cast steels, silicon is considered an alloy. As an alloy, silicon is useful for several purposes: (I) for its effect on magnetic properties of parts for electrical apparatus; (2) for increasing the yield strength of carbon and low-alloy steels without too much sacrifice of ductility and weldability; (3) for adding hardness and toughness to spring and chisel steels; (4) for adding resistance to scaling and carburization to heat-resistant steels; and (5) for its graphitizing effect in graphitic steels. In acid electric steels for casting we are principally interested in the effect listed second; i.e., increase of strength with minimum sacrifice of ductility.

Jan 1, 1947

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1915 to Jan. 10, 1916. ANDERSON, FRANK BASIL, Min. Engr., Sampler, Copper Queen Cons. Min. Co., Bisbee, Ariz. BAILEY, LEWIS NEWTON, Min. -Engr 4227 St. James Place, Sail Diego, Cal. BELL, JAMES E., Min. Engr., Care Chile Exploration Co., Chuquicamata, Chile, South America. BONILLAS, YGNACIO SAFFORD, Min. Geol., Copper Queen Cons. Min. Co., Bisbee, Ariz. BRADLEY, GEORGE OLIVER, Mech. Engr Hobart Bldg., San Francisco, Cal. CLARK, GEORGE L., Min. Engr Vipond Mine, Schumacher, Ont., Canada. CONKLING, RICHARD A., Geol., Roxana Petroleum Co. of Oklahoma, Tulsa, Okla. GOHRING, W. B.. Geol., Supt. of Mines, Calumet and Arizona Min. Co., Warren, Ariz.

Jan 2, 1916

THE education of adolescents to perform the duties and assume the responsibilities of maturity has been a characteristic of human society since the dawn of history. In the beginning the members of the immediate family performed this function, and in modern life they still have an important part in it. Possibly religion was the first field in which education began to be functional; young people were sent for instruction to a teacher who had a broader and deeper knowledge of the subject than was possessed by the family. It does not seem necessary for our purpose to attempt to determine how, when, or where instruction in the practical arts first began to become functional, and the brief outline which follows must suffice. The discovery and utilization of mineral substances to improve and maintain the conditions of human living is a practical art, which must have had an almost accidental origin and have been developed by empirical experiments. We do not know, nor would it be useful to try to fancy, how men first learned that they could make use of mineral substances to their benefit, but however that knowledge was initially gained it was certainly trans- mitted through instruction in the family. At fist such activities must have been merely a minor part of the making of a living, bit in time those who excelled found it better to devote them-

Jan 1, 1941

By David B. Brooks, William A. Wallace, James R. Dunn

As the conflict between the mineral industry and preservationists steadily increases, it becomes urgent to determine as precisely as possible the costs of developing vs. not developing our domestic mineral resources so that enlightened mineral policy decisions can be made. A simple discounted cash flow equation is suggested as an approach to assigning a public-interest dollar value to mineral resources. Present value of a piece of land underlain by a mineral resource is taken as equal to the discounted cash flow derived from the resource corrected for present and future surface land values. The equation is effective as a base for mineral aggregate resource planning for metropolitan areas if transportation cost differences are substituted into the cash flow component. Suitably modified, the equation can be fitted readily into an existing computer simulation program for aggregate mineral resource planning in metropolitan areas. However, because of the lack of accurate input, the equation is less effective for other mineral commodities such as base metals and coal. Nevertheless, within a somewhat philosophical context, the equation still has utility and is effective in defining the problem of public interest values for minerals other than mineral aggregates.

Jan 1, 1972

By Howard V. Sears

ArcHodrilling (Arcuate Hole Drilling) of short radius overhead curved holes from within the working level with a new, small-diameter in-the-hole drill produces tangible, assayable chip samples from the entire height of the projected mine level where the hole arcs down immediately in front of the working face. Drilling through the projected level with diamond coring tools produces samples showing the competence of roof and floor strata as well as the geological and economic characteristics of the ore. Hand-portable solid state electronic surveying instrument has been developed to survey the ArcHole and a convenient nomograph plotting record sheet converts survey digital readouts to hole inclination in degrees, to radius of curvature in feet, and to attitude of the plane of curvature from vertical in degrees, all without calculation. The ArcHodrilling system offers a tool with which the exploration geologist can more nearly assess the true potential of old mining properties being reexamined and to reduce the number of surface diamond drill holes needed to secure development data about new ore bodies. It gives the mine geologist an opportunity to secure those data at a fraction of the cost of drilling from the surface. The mining supervisor has a convenient, cheap tool to look ahead to know what he will be mining tomorrow. The mill supervisor has an opportunity to reduce his mineral loss in tailings by being able to anticipate the grade of his mill feed.

Jan 1, 1973

NEW MEMBERS The following list comprises the names of those persons who became members during the period Aug. 10 to Sept. 10, 1914: Members ALLEY, HARRY MCCAMMON, Mill Foreman .... Churchill Mining Co., Wonder,2 Nev. AMBLER, J. OWEN, Met..; ... Calumet and Arizona Mining Co., Douglas, Ariz. ANDERSON, JAMES WILLOUGHBY, Duell, Warfield and Duell, 2 Rector St., New York, N. Y. ANTISELL, FRANK L., Asst. Supt Raritan Copper Works, Perth Amboy, N. J. CARRINGTON, FRANK GAMBLE, Sec'y and Asst. Mgr., Standard Foundry Co., Anniston, Ala. CONKEY, CHARLES ROLLAND, Structural Draftsman, Barnett McQueen Co., Ft. William, Ont., Canada. COOK, PAUL RICHARDSON, Mill Shift Boss, Buckhorn Mill and Cyanide Plant, Buckhorn. Nev.

Jan 10, 1914