Search Documents

By Donald W. Gentry, John F. Abel

This paper presents some of the results of a rock mechanics instrumentation program designed for, and implemented at. longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam, and immediately below the coal seam. Longwall test panel 4N had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft), [Fig. 1]. The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) although it ranges from 73-134 m (240-440 ft). Roof support at the face was provided by 116 Hemscheidt 320 HSL shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1979

By D. L. Rainey, E. R. Goter, W. R. Hudspeth

THE area in which spodumene-bearing pegmatites occur extends from Gaffney, S. C., in a northerly direction to Lincolnton, N. C., a distance of about 16 miles. The zone averages 2 miles in width. Interest in this area was first aroused by the discovery of small amounts of cassiterite in the pegmatites and in greissen which occurs on the walls of some of the pegmatites. Attempts were made from 1880 into the 1920's to mine and concentrate cassiterite, but there were no successful operations. In 1935 L. M. Williams became interested in the area and began prospecting by trenching and sinking several small shafts. He gradually gained control of a considerable acreage south of the city of Kings Mountain, N. C. Mr. Williams states that he produced some ore from a shaft which he shipped to the Maywood Chemical Co. in the late 1930's. In 1937 G. H. Chambers of the Foote Mineral Co. visited the area and examined several properties, but the lithium market was too small to support the necessary concentrating plant.

Jan 9, 1953

By Joseph Kuti

ROOF SUPPORT DEVELOPMENTS IN LONGWALL (1) European longwall mining technology developed towards its modern form in relatively deep mines. With increasing depth the stability of openings driven for ventilation, travel or transport becomes paramount in mine design considerations. As a result the number of roadways and entries, as well as their width must be a minimum. (1) Another important aspect of European mining is the high density of mineable seams, as opposed to the wide lateral extension of a single seam in the U. S. A. Multi-seam mining requires strict planning and near 100% extraction, since with increasing depth, the effect of remnant pillars can be devastating. As a result the face layout of a modern European longwall panel is based on single panel entries of moderate width and great height. The mode of extraction is generally a mixture of the advance and retreat system which is called a 2-system. It is obvious, therefore, that the supports developed for the entries and for the intersection areas are more complex than those in the U. S. A.

Jan 1, 1981

By S. Korman, S. B. Tuwiner

Chalcocite flotation is affected by agitation intensity during conditioning. Sodium sulphide in minute quantity may activate or depress, depending on conditions. Oxygen is a depressant while oxygen and sulphide neutralize each other by re-action at the mineral surface. Diffusion across a stagnant film at the surface governs reaction rates, while film thickness is reduced upon increase of agitation intensity.

Jan 2, 1950

By C. H. Wayman, D. W. Fuerstenau

THE gas phase is one of the indispensible ingredients in flotation operations. Flotation depends on the collision of an air bubble and a mineral particle in a pulp and their ability to remain in contact long enough for adherence to take place. Before it is possible to understand the mechanics of air bubble-mineral particle encounter, it is necessary to learn more about the nature of bubbles themselves before collision with a mineral particle has taken place. To date, little work has been done on air bubbles in flotation systems. In 1945 Fahrenwald1 presented a study of the role of frothers on air bubbles and on aeration in flotation, and recently Wark and Sutherland2 discussed the work of Rosenberg3 in relation to flotation. The research reported in this present article was undertaken to investigate systematically the effect of bubble size and the concentration of certain reagents on the terminal velocity, shape, path, and drag coefficient of single bubbles in distilled water. Most of the work is concerned with the effect of a-terpineol on bubble motion in water, but studies were made with potassium chloride, potassium hydroxide, potassium ethyl xanthate, and potassium amyl xanthate.

Jan 6, 1958

Jan 1, 1890

By E. Berl

THIS may be a most unnecessary paper-from what does crude oil come and how was it formed? Many people, inside and outside of the petroleum industry, believe that we have actually enough oil, and that we can easily produce very important products from this extremely valuable raw material. The writer believes, however, that the answer to this question concerning the parent material and the formation of oil is of broader interest, because it may be that from the answer to these problems it would be possible to get answers to other important indus-trial questions. Therefore, a study in this line seems to be justified, and the writer will submit some of the results which he has collected during more than ten years with many very capable collaborators, to whom his thanks may be expressed on this occasion.

Jan 1, 1938

By William Hutton Blauvelt

An official of one of the prominent iron companies of the South recently made the following statement during a discussion of the present conditions of the Southern iron business: " The trouble with us in the South has been that we have been satisfied to buy iron and coal lands, build blast-furnaces, and make pig-iron. We stopped at pig-iron, and as a result we are all poor. The South needs diversified industries, and needs to work up its raw products into articles the Southern market can use. If we had realized this sooner, some of us might now be rich." The South is awakening to this view, and in the Birmingham district alone one basic steel-mill is already in operation, and in a year's time another and much larger one will be turning out rails and shapes, with rod- and wire-mills in prospect. It is to chronicle another metallurgical step forward in the same district that I have prepared the following description of the new by-product retort coke-oven plant recently put in opera-

Jan 1, 1899

By C. B. Dudley

IN the spring of 1877, the Pennsylvania Railroad Company became so dissatisfied with the average life and wear of the steel rails it was then able to procure, that it determined to make an investigation into the chemical composition and physical properties of steel rails, with a view, first, to answering the question why one steel rail has to be removed from the track after, perhaps, eight months' service, while another lasts ten years ; and, secondly, if this investigation succeeded in throwing light on this important subject, to use this information in securing better rails in the future. The results

Jan 1, 1879

By Charles B. Dudley

In the spring of 1877, the Pennsylvania Railroad Company became so dissatisfied with the average life and wear of the steel rails it was then able to procure, that it determined to make an invest,igation into the chemical composition and physical properties of steel rails, with a view, first, to answering the question why one steel rail has to be removed from the track after, perhaps, eight months' service, while another lasts ten years; and, secondly, if this investigation succeeded in throwing light on this important subject, to use this information in securing better rails in the future. The results

Jan 1, 1879

By Wells A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into water-courses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appropriative water titles. But by far the most profound impact on western water law was made by the gold- seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the-miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.' They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.'In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State.""

Jan 2, 1960

By F. Keeler, C. M. Craighead

Aluminum alloys containing magnesium and silicon are susceptible to strengthening and hardening by suitable heat-treatments, and they constitute a class of alloys of considerable commercial importance. Generally, they contain these two elements in the proportions required for the formation of the intermetallic compound Mg2Si, or an excess of silicon; no commercial wrought alloys are made with an appreciable excess of magnesium. The reason for not having excess magnesium is obvious from the results given in this paper, since it is shown that excess magnesium results in a proportional decrease in the solubility of Mg2Si. This is the eighteenthl of a series of papers from the Aluminum Research Laboratories dealing with the equilibrium relations in aluminum-alloy systems; most of the previous publications concerned binary aluminum-alloy systems; this is the fourth of a group pertaining to ternary aluminum-alloy systems. The work on this system was completed in 1930, but the results were not published because of the pressure of other work. Hanson and Gaylor2, in 1921, presented the results of an extensive investigation of the aluminum-magnesium-silicon system. Their results indicated that an excess of magnesium over the amount required to form the compound MgzSi caused a noticeable decrease in the solid solubility of MgzSi in aluminum. A more recent investigation3 in these laboratories showed that the solid solubility of MgzSi in aluminum was 1.85 per cent at 595' C. and decreased to 0.30 per cent at 300' C. The results of the latter investigation were used as the basis for the present work. The Present Investigation In the present investigation, a study was made of the effect of various amounts of excess magnesium upon the solid solubility of MgzSi in

Jan 1, 1936

Jan 1, 1887

A mine that staggers the imagination is Chuquicamata, the granddaddy of them all. In 1968 production exceeded 300,000 tons of copper. Production began in 1915 and mining proceeded solely on oxide ores until 1953 when the first treatment of sulfides began. Today the company has mined about 1.2 billion tons of all types of material since inception. The accelerating rate of output can be gauged by the comparable 1946 figure of production-to-date which was 350 million tons. No single mine comes close to touching Chuqui for productivity at its high annual metal yield mining only 90,000 tpd of ore at the luxurious waste-to-ore ratio of 0.6 to 1. However, the complexity of the operation is enormous and the experience required to synchronize the various processes is masked by normal operations and only becomes apparent in times of emergency such as when the slide took place in the pit in February.

Jan 11, 1969

By Albert F. J. Bordeaux

This paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there mas a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. General Outline of the Cyanide Treatment. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed: 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By Earle J. Klohn

Mining operations have been carried out in British Columbia since the time of the first settlers in the area. The early developments were mainly small volume, high-grade operations, producing small quantities of tailings wastes. In these early days the nearest stream was a logical first choice for tailings disposal. Where streams suitable for accepting the tailings were not available or where streams crossing the International Border could not be used for this purpose, the nearest convenient land site was selected for storing the tailings. Old tailings waste piles exist at many locations in the Province and are readily evident, for example, in the Princeton and Hedley areas. Figs. 1 and 2 are photographs showing the present condition of two of these old tailings dams. [ ]

Jan 1, 1972

By C. A. Edwards

Jan 1, 1935

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Septa 10, 1917, to Oct. 10, 1917. ALDER, ALFRED 1020 Kansas City St., Rapid City, So. Dakota. AUBEL, VERNE WALLACE, Night Supt. of Works, Broken Hill Proprietary Co., Ltd., Newcastle, N. S. W., Aust. BAKER, ROBERT EARL Works Mgr., Keokuk Electro-Metals Co., Keokuk, Iowa. BALLAMY, JOHN H., Min. Engr., Delaware, Lackawanna & Western Railroad Co,Scranton, Pa. BRADLEY, ALLEN PALMER, Met., American Smelting & Refining Co., Murray, Utah. BRIGGS, WALTER M Pres. Regal Mines Co. Dedham, Mass. BRONSON, EDMOND B., Pres., Bagdad Copper Co., 120 Broadway, New York, N. Y. BROOK, NILES WINFIELD, District. Mgr., Cleveland Min. Co., 625 Bank & Insurance Bldg., Dubuque, BUSKETT, EVANS 1V., Assayer, Custom Assay Office, 620 Joplin St., Joplin, Mo. CAMPBELL, JOHN HATES, Chem. Engr., Robert W. Hunt. & Co., 2200 Insurance Exchange, Chicago, Ill.

Jan 11, 1917

By A. E. Hunt, G. P. Clapp

This paper constitutes in substance a part of a more elaborate chapter, accompanied with extended tables of analyses, prepared for the book of Mr. Fred. H. Whipple on " Water-Supply." In advanee of that use of the material, however, it seemed appropriate to lay a portion of it before the Institute; and this opinion of the authors, the Council, by accepting the paper, has ratified. It may seem at first glance, nevertheless, that a paper dealing chiefly with this subject in its sanitary aspects, and only treating in a subordinate way of the one subject (boiler-scale) usually deemed to concern our professions, is somewhat out of place in our Transactions. But reflection will, we trust, correct this impression. In recent periods, and in continually increasing degree, the managers

Jan 1, 1889

By Leon Dominian

The lack of Aryan roots for the names of metals commonly known among the Aryan settlers of Asia Minor, as well as the later colonizers of Europe, indicates that these races were generally ignorant of the use of metals until they came into contact with Semitic peoples. Practically all mining-terms in current use among the earliest Greeks resemble very strongly their distinctly Semitic equivalents, which can be traced all the way in a broad belt beginning in Lower Mesopotamia, and extending westwardly to the Syrian shores of the Mediterranean. The Greek word 'metallon," for instance, used indiscriminately to designate mine or ore, probably came from the earlier Semitic equivalent, " matal." Again, the Greek words " chry-sos " (gold) and " chalkos " (copper) seem to be descended from the Semitic forms " chrouts " and " chalak." It is a natural inference that primitive mining-methods were evolved by the dwellers in the mineralized areas of Asia Minor, from whom later Greek, Roman, and even North European miners obtained their first not.ions of the reduction of metallic ores, by

Jan 1, 1912