Search Documents

By E. H. Jr. Dix

DURING an investigation of high-strength manganese bronze by the Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received the early consideration of scientific research. The diagram, according to the most recent work,1 is shown in Fig. 1. The disputed questions involve the termination of the beta field and the line at 470° C. The earliest experimenter, Roberts-Austin, detected an arrest in some of his cooling curves at approximately this temperature and ascribed them to the formation of a eutectic; it has since been proved that there are no eutectics in this series. Shepherd2 was unable to detect any thermal arrests at this temperature; his diagram was essentially as shown in Fig. 1, except that the line at 470° C. was omitted and the beta phase carried down to normal temperatures. Later, Carpenter and Edwards,3 by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the beta constituent into a eutectoid of alpha and gamma. Microscopic evidence of the formation of the eutectoid is doubtful and it seems more likely to be due to an allotropic change in the beta constituent as shown by Fig. 1. At least for practical purposes, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather than alpha plus an unresolvable eutectoid of "apparent beta" as it has often been called.

Jan 5, 1922

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By W. R. Bean

Probably few, if any, of the many serious problems confronting malleable foundries have been more difficult of solution than the question as to why malleable that is ductile, black in fracture, and normal in all respects before galvanizing should, by that process, be rendered brittle, brilliantly crystalline or "white" in fracture, and of low resistance to shock. So far as we are aware, the technical literature contains no data or discussions on this subject, except two referencesl,2 of a general character. It is apparently a question that every one concerned, producer and consumer alike, has been willing to evade as far as possible. Various theories as to the cause of the deterioration have been given but such checking of these theories as we have done indicates that there was no sound basis for most of them. This work on the galvanizing of malleable was first undertaken in 1916, and has continued until the present time. We now feel that for all practical purposes we have reached a solution and are glad to be able to offer it in a form that can be readily applied to production processes. It is impossible to give here a detailed account of the early work done on this problem. A great number of tests were instituted and an enor-

Jan 1, 1923

By W. R. Bean

Probably few, if any, of the many serious problems confronting malleable foundries have been more difficult of solution than the question as to why malleable that is ductile, black in fracture, and normal in all respects before galvanizing should, by that process, be rendered brittle, brilliantly crystalline or "white" in fracture, and of low resistance to shock. So far as we are aware, the technical literature contains no data or discussions on this subject, except two referencesl,2 of a general character. It is apparently a question that every one concerned, producer and consumer alike, has been willing to evade as far as possible. Various theories as to the cause of the deterioration have been given but such checking of these theories as we have done indicates that there was no sound basis for most of them. This work on the galvanizing of malleable was first undertaken in 1916, and has continued until the present time. We now feel that for all practical purposes we have reached a solution and are glad to be able to offer it in a form that can be readily applied to production processes. It is impossible to give here a detailed account of the early work done on this problem. A great number of tests were instituted and an enor-

Jan 1, 1923

Large equipment for quarrying and for the various stages of crushing and grinding are the trend for new and existing operations. Included are large size haulage units, fast drilling equipment, impact crushers and large mills capable of high tonnage rates for metallic and nonmetallic minerals. In grinding, large-size mills continue as the choice in industries where grinding constitutes a major portion of the processing. Typical is a 10 x 34 ft two-compartment mill in closed circuit with an 18-ft diam air separator for cement. Other cement mill sizes are in the order of 12 x 36 ft, 2500 hp; 10 x 37 ft ball and rod (wet), 1400 hp; 13 x 36 ft, 3000 hp; 13 x 40 ft (wet), 3000 hp. Several installations of combination ball and rod mills have been made, and one of the largest is 12 x 45 ft. In connection with the wet grinding of raw materials, the DSM 270-degree screen has been installed in several cement plants with the intention of producing a material finer than 50 mesh. In ore processing, large autogenous mills (121/2 x 20 ft) are being installed.

Jan 2, 1964

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metal-lurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each, temperature from room temperature to fusion tempera-ture, and cooled at a rate that is not generally controllable but is pre-determined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each tem-perature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and dis-advantages of the extent of the zone are of prime moment, and are dis-cussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known.

Jan 1, 1935

By David H. Browne

The trite maxim that man is a tool-using animal might nowa-days be amended by saying that man is a tool-choosing animal. The chipped flint, at first all-sufficient, gave way to hammered bronze, and that, in turn, to wrought-iron and steel. As our knowledge of metals increases, we learn to specialize; we temper and anneal; we alloy and intermix; and we fashion for ourselves a metal suitable to our necessities. The knowledge of the properties and uses of the various metals and their alloys has become the capital of every constructive engineer, and the currency of every intelligent brass-founder aid blacksmith. Prom year to year, the specifications of the designer become more rigid, and the steel-maker is forced to study more closely the qualities obtainable by changing the treatment, or altering the composition, of his metal. Of making alloys there is no end. We have heard much, during the last decade, of manganese-steel and chrome-steel, of aluminum and tungsten, of titanium- and silicon- and copper-steels, and of every conceivable union into which steel could be coerced or cajoled. Without denying to each of these alloys novel and valuable properties, it. must be admitted that, of all alloys, the one which shows the greatest range of adaptability, and has met the largest measure of popular approval, is nickel-steel. Introduced to public notice by Mr. Riley, in 1889, its field of usefulness has been rapidly enlarged, until, at the present day, the use of nickel-steel is as thoroughly recognized as that of carbon- or manganese-steel. Concerning the properties of nickel-steel numerous articles have appeared in the technical journals. For the man in a hurry, who wishes to look up the properties and limitations of nickel-steel, these articles might almost as well be in the lost

Jan 1, 1900

By A. C. Boyle

PaGE I. Introduction.........68 II. Location of the District,....... • 70 .. III. Stratigraphy...........73 Description of the Rocks.......73 Triassic Eruptives (Andesite Flows and Tuffs) ....73 Triassic Sediments (Shales and Slates)..75 Areal Geology ............75 Structure...-.......76 Folds............. 76 Faults..........79 Shear ...........80 Intrusives..........81 Alaskite Dike.........81 Andesitic Intrusion.......82 IV. PetrogRaphy of thE Rock Types......83 Andesite Flows.........84 Tuff 8...........84 Andesite Tuff........84 Rhyolite Tuff.....-.......85 Alaskite-Porphyry.......89 Andesite Dike........91 V. Description of the Mines......92 VI. Metalliferous Deposits ........ 95 Character of the Ores...........97 Mineralogy of the Ores.......97 Metallic Minerals.......97 Microscopic Character of the Ores...98 Secondary Enrichment....... 103 Genesis of the Ores ...........104 VII. The Sulphate Deposits.......109 Gypsum ..... HO Anhydrite......... ,... 110 Barite............ 110 Origin. with special reference to Gypsum....111 VIII. Summary.............. 113 IX. BIblYogRaphY.............114

Jan 1, 1915

By Samuel L. Hoyt

Cemented tungsten carbide, a product of a branch of metallurgy which has never possessed more than a relatively minor interest and importance, has recently commanded the attention of engineers, industrialists, financiers and men of business. New methods, new opportunities, new goals, never before considered, have suddenly been brought within the scope of practical realization. It is these results that attract the interest of the world, but we, as engineers and metallurgists, will have equal interest in the product itself and in that branch of metallurgy from which it comes. It seems appropriate, therefore, to speak today on Hard Metal Carbides and Cemented Tungsten Carbide, as the latter represents one of the outstanding developments of recent date in non-ferrous metallurgy. We are interested in the hard metal carbides as a group of related metallic substances and in cemented tungsten carbide as the leading representative of the metallurgy of this group. The literature of this general field is limited, and, bearing this in mind, it seems advisable to attempt to cover the field broadly and to correlate the subject matter, rather than to present a detailed account of any one of its phases. Our annual lecture lends itself admirably to this plan. The quickened interest in cemented tungsten carbide, once its potentialities were recognized, the many sides to the problem of developing the manufacture and use of this new product, and the desire to economize as much as possible in the time of development, have brought many into this work, both in this country and abroad, notably the Osram Lamp Co. and Friedrich Krupp in Germany and the General Electric Co. in this country. It would be presuming too much to attempt to speak too broadly of the present state of the art and science of the hard metal carbides and my remarks arc guided largely by the work done in the General Electric Co., and by our associates in the Carboloy Co. Even here the activities of many in these two groups have centered around the utilization of cemented tungsten carbide, which is outside the scope of this talk. To those whose work is represented in this lecture, it is my pleasant duty to acknowledge their assistance and advice. To Dr. Zay

Jan 1, 1930

By C. E. Sims, C. A. Zapffe

MANY hundreds of publications have appeared during the past 78 years that treat the subject of hydrogen in iron and steel,105 but conclusions regarding the functions of hydrogen in causing some important defects in steel are still unsatisfactory to many; and other hydrogen-caused phenomena yet remain to be identified with this gas. The most widely discussed of these defects is hydrogen embrittlement, but the conception, perhaps the popular one, that embrittlement is due to hydride formation does not conform to the known facts.104 The true identity of hydrogen embrittlement seems instead to lie in a mosaic nature of metal crystals, which is a concept not yet accepted by most metallurgists. A study of hydrogen embrittlement therefore provides new viewpoints in regard to the crystalline substructure of steel. A second widely discussed hydrogen-caused defect is the "flake" or "shatter crack." Although it is generally agreed that the presence of hydrogen is a prerequisite for their appearance, it is also realized that internal stress plays a decisive part. The relationship of hydrogen to internal stress has not been explained very clearly; nor is it always clear what the relationship is between a "flake" and a "snowflake," or between a "fish eye" and a "shatter crack." More importantly, the relationships among hydrogen embrittlement, hydrogen-caused fissures such as "flakes" and the ultramicroscopic structure of steel have scarcely been recognized. The present investigation attempts to provide an explanation for the embrittlement of steel by hydrogen by showing cause for accepting the "block" concept of metal crystals, and then to show how the numerous hydrogen-caused defects are interrelated in the light of this concept. EVIDENCE OF SUBSTRUCTURE IN METAL CRYSTALS It appears that the concept of a crystal as an aggregate of smaller multi-atom units must be accepted in some form if the behavior of metals is to be understood. The abundant literature on the evidence of an ultramicroscopic "mosaic" structure in metals and other crystalline substances suggests that the physicist has provided the metallurgist with an invaluable new insight. The exact picturization that any one physicist provides may be open to question, but the fact that there is some such fundamental substructure seems undeniable. The present work makes no pretense of comprehensively treating the imperfection structure theories. Nor will conclusions be drawn here regarding the exact nature of the substructure of crystals. However, the acceptance of some imperfection theory of fundamental attributes seems so necessary to an understanding of the behavior of hydrogen in steel that the following brief

Jan 1, 1941

By C. R. Austin

THE paper describes an investigation on the pressure welding of low-carbon steels. The work necessitated a reproducible mechanical means of making the weld and also a test that would indicate the nature and completeness of the union. An apparatus including a high-temperature furnace was devised for making the welds, and the ordinary tensile pulling test 'in correlation with macroscopic and microscopic observations was used as a means of examining the result. Initially it was intended to devise some simple test of weldability, but as the experimental work progressed, it soon became clear that with our limited knowledge of the exact nature of the mechanism of pressure welding it was impossible to interpret our results or to devise a simple test of weldability. Hence it was manifestly necessary first to study the mechanism of such welding and attempt to elucidate the fundamentals underlying the so-called welding of steel by pressing together two metal surfaces. It also became evident that it was necessary to define the term "welding." In many early experiments when, two heated rods were pressed together and then pulled in the cold, very high tensile values were obtained, and yet the fracture took place exactly in the line of junction except for a few small scattered areas. In other words, the' rods pulled apart just as they were before being "stuck" together and had certainly not welded completely, despite the high value indicating the strong cohesive force operating. In this paper, welding has been considered as a form of intimate contact between two metal surfaces, so that the units lose their individual identity and there is no change in physical properties in passing through the weld from one unit to the other. This is defined as "true welding." When true welding has taken place completely over the whole section, the probability is that the rupture in tensile test will occur outside the weld.

Jan 1, 1932

By Edgar Bain

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin, Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By Frederick Beckett

WIDESPREAD experimentation has been conducted in recent years to devise a means of preventing intergranular corrosion in austenitic chromium-nickel steels of the 18 per cent chromium-8 per cent nickel type. Additions of titanium to these steels have been used commercially to overcome this difficulty, as advocated by Krupp of Germany, and the latest literature reference concerning improved details of this method is the article by Bain, Aborn and Rutherford.1 Extensive work by the present authors has shown columbium also to be a particularly valuable agent for inhibiting intergranular corrosion. This paper does not deal with steels that are largely or wholly aus-tenitic ; it is limited to a discussion of the results obtained through the use of titanium and columbium in plain high-chromium steels. For many years titanium has been used commercially by some steelmakers as a cleanser, and to a lesser extent as a hardener, but then in greater per-centages. The results of the work to be described disclose that titanium and columbium in proper proportions act as effective softeners in the high-chromium steels. It is well known that chromium intensifies the hardening effect of carbon in steel; it imparts pronounced air-hardening properties within a rather wide range of chromium content; it provides increased ductility in steels of given strength and hardness; and it enhances resistance to corrosion and oxidation at elevated temperatures to a marked degree. However, in applications requiring a combination of some of these valu-able properties great hardness is frequently a detriment rather than a merit. When the objective is a soft and ductile steel having optimum corrosion resistance, the producer strives for a carbon content as low as commercially practicable.

Jan 1, 1933

By L. L. Wyman

SINCE the presentation, by the writer, of the initial paper on the embrittlement of copper,1 the subject has been investigated further along two separate lines. The first series of investigations involves the "double-deoxidized" copper, while the second series is devoted to single deoxidizers other than those used in the investigations reported upon last year. The object of these experiments is to develop a type of copper that will show the minimum of detrimental effects after having been exposed to alternate oxidation and reduction. The fabrication of this material necessitates the use of alternate oxidizing and reducing atmospheres, at temperatures ranging up to 900° C. Following this treatment it is essential that the soundness and strength of the copper be unimpaired, even in sections of only a few thousandths of an inch in thickness.

Jan 1, 1932

INCREASING realization that pouring and ingot-mold practices involve many factors of fundamental importance to ingot quality and general steel-mill operations has caused these phases of steelmaking to become major concerns of operators and metallurgists engaged in control of quality and costs. Methods of pouring steel from the ladle into the ingot molds have some direct effects on ingot quality. The mold itself governs solidification and dimensions of the ingot and in so doing exerts some very tangible influences not only on ingot quality but also on product yields and general steel-mill processing. In addition, practices are employed' in the handling of molds during daily open-hearth operations that are important to quality and production costs. Therefore, pouring and mold practices must be considered highly specialized and important steps in steel-mill operations. MOLD DESIGN Mold design is difficult to discuss in a precise manner because it varies greatly throughout the industry, both in theoretical concepts and practical application, and few well developed data are available. Most ingot molds are designed to meet conditions peculiar to a given plant wherein quality standards are dictated by end-use requirements, which may differ considerably, even for the same grade of steel. The mold designer must also consider the equipment available to process ingots and the product obtained from them. Such equipment, used for stripping, heating, blooming and finishing operations, is seldom, if ever, exactly the same in any two steel plants. Thus, pronounced contrasts in mold designs can be expected to continue, even among plants making strictly comparable types of product, particularly because some producers are just beginning to realize the benefits possible from specialized designs. Certain fundamentals are used in mold design but even these

Jan 1, 1951

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By C. N. Schuette

The material presented in this paper has been gathered by the writer during a long and varied experience on matters pertaining to the quicksilver industry. During the past 18 years he has visited practically all of the quicksilver mines of the United States and has had occasion to review the literature on quicksilver mining the world over. In a previous publication1 the conclusion was expressed "that the greatest opportunity for increasing the economy in quicksilver production lies in giving more attention to the geology of the deposits ... " The present paper is a contribution toward that end. Due to a lack of correlation of the observed facts, a great deal of confusion exists in the views of various writers concerning the mode of occurrence of quicksilver ores. This paper attempts to show that certain common factors underlie the formation of all quicksilver orebodies. It attempts to present a framework on which to marshall the observed facts and thus make clear the interrelation of various observations which at first sight appear to be contradictory. The material presented is fragmentary in many respects and it is hoped that readers familiar with the deposits mentioned may supply the deficiency. The reader is asked to refer to the publications cited for maps and additional information on the individual orebodies, as this review, in covering so much territory, must necessarily confine itself to a bare outline of the facts concerning each occurrence. The writer hopes that this paper will elicit comment and criticism from the many competent men interested in the quicksilver industry and to all of them he would express his indebtedness for the many courtesies that they have extended to him at various times in the past. Theory op Primary Concentration The mode of occurrence of any given orebody presents an individual problem to the miner engaged in exploiting it. No two orebodies are exactly alike in their geological relationships, therefore an understanding, in detail, of the geology is necessary if the orebody is to be exploited in the most economic manner.

Jan 1, 1931

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By James F. Kemp

(San Francisco Meeting, September, 1915) THE iron ores of southeastern Cuba present a subject of exceptional geological interest. Their relations to the inclosing rocks are varied and in some cases unusual. The problem of their geological origin is not a simple one and for this reason has occasioned some divergence of views among previous observers. Profiting, however, by. these earlier studies and by more detailed field and laboratory observations as well as by the experience of added years of mining, much more satisfactory descriptions and interpretations can now be prepared. PREVIOUS WORK In 1884, interest in the southeastern coast of Cuba became active among the consumers of iron ore along the Atlantic seaboard of the United States. Active development was undertaken by the Juragua Iron Co., Ltd., a corporation affiliated with the Bethlehem Steel Co., and the Pennsylvania Steel Co. The property of the Juragua company, which is situated about 15 miles east of Santiago, was studied in June and July, 1884, by Dr. James P. Kimball, at the tine Professor of Economic Geology in Lehigh University and one of the best known of American mining geologists. Dr. Kimball published on his return two papers, the first important descriptions which we have of the local geology.1 It is

Jan 9, 1915

By H. M. Hobart

This paper deals principally with investigations undertaken by the Welding Research Sub-committee of the Welding Committee of the Emergency Fleet Corporation. The general object of the investigations has been to extend the use of welding in the construction of merchant ships and, specifically, to provide a definite basis for obtaining the greatest economy and efficiency in employing welding in place of riveting in the construction of the hulls of such ships. Composition of_ Ship-plate Steel The chemical composition of the steel employed in such hull construction varies with the thickness of the plates. Through the courtesy of Mr. H. Jasper Cox, of Lloyd's Register of Shipping, the following information may be given concerning the kind of steel plate employed in American shipyards in 1918 for the hull construction of merchant ships. Lloyd's requirements do not relate to the chemical composition. They require a tensile strength of 58,000 lb. per sq. in. (40.75 kg. per sq. mm.) for their lower limit and 72,000 lb. per sq. in. (50.59 kg. per sq. mm.) for their upper limit. For the information of the Committee, Lloyd's obtained from their surveyors at various works data of the carbon content, which is as follows: Works Carbon Content for Plates 1/4 In. Thick 1 In. Thick A..................... 0.14 0.23 B..................... 0.14 0.25 C2.................. 0.19 0.25 D................. 0.20 0.30 E Upper limit..... 0.35 Lower limit..... 0 24 0.29 Upper limit,.... 0.25 0.30 Lower limit..... 0.21 0.27 Upper limit..... 0.25 0.35 Lower limit..... 0.22 0.28

Jan 1, 1920