Search Documents

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By Frederick Laist

ABOUT six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electro-negative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection-1 mg. or less per liter.

Jan 10, 1920

By Walter Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not, been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economi-cally prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established.

Jan 1, 1938

Jan 1, 1968

[A AALSETH Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Mont ABADIE Henry G (M 43) Asst to. Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif. ABBET Waldo (A 56) Asst Diet Oper Supt Sun Oil Co P 0 Box 66, Stowelt, Tex ABBOTT Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT Fred E Jr (M 59) Abqaiq Diet Mgr Arabian American Oil Co Dhahran, Saudi Arabia ABBOTT J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT Richard H (J 51) Partner Abbott & Howard 422 W Hermosa, San Antonio 12, Tex ABBOTT William G (M 50) Div Mgr Rice Engrg &. Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carml, 111]

Jan 1, 1961

By T. A. Wilson

THE plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,1 which has become a classic, and also by one of the present authors in a somewhat shorter account.2 The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been clone on single-crystal zinc, but as it 'is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips3 have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94° removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.

Jan 1, 1927

To Americans, Alaska occupies a unique position, both geographically and historically. The only integral portion of the United States lying in the sub-Arctic and Arctic regions of the Earth, the early remoteness and climatic conditions effectively combined to impede the economic development of this area. Although Alaska has been a part of our Nation since 1867, its mining industry is still at that stage of development which characterized the West 100 years ago when miners concentrated on high-grade lodes and rich placer deposits. Since World War II, however, there has been a noticeable increase of interest in the raw materials of the North. This concern has been most noticeable in Canada, Scandinavia and Russia, but it has been, and is being shown in Alaska. To the American mining industry, the potential importance of this State can be summed up by the question, "Can Alaskan mining compete successfully with those of other states and countries?" The answer revolves about the vital factors of geography, economics, and the political turmoil of the World. These aspects are among those discussed on the following pages in a series of articles by Alaskans and non-Alaskans alike. We invite you to read "Alaska: Regional Report."

Jan 12, 1961

By Francis Lucas

A microscope objective of given numerical aperture, whew used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability-the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise whew the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500, µµ and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.65 N. A. are wow an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Köhler and Dr. M. Vow Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 µµ which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 6, 1926

By Alex Hay

THE Sydney coal field, the largest and most valuable in Nova Scotia, is situated on the northeastern coast of the Island of Cape Breton, extending from Mira Bay on the south to Cape Dauphin on the north, a distance of 30 miles, and has a general dip northeast under the sea. (Fig. 1.) The field embraces the mining villages of Morien, Birchgrove and Reserve and the towns of Dominion, Glace Bay, Waterford and Sydney Mines. The city of Sydney is situated about midway between the northern and southern extremities of the field and on the western fringe of the productive coal measures. Sydney harbor crosses the coal field, cutting off direct rail connection between Sydney Mines and the greater part of the field to the southeast. (Fig. 2.) The coal measures are exposed in the cliffs on the coast line, which rise to an average height of 30 ft., and are almost continuous throughout the length of the field. The portion of the coal field under land forms a small segment of a circle, the greatest distance from the coast landwards is 9 miles, and it occupies an area of 200 sq. miles. The greatest distance developed seawards from the shore by mining operations is 2 ¼ miles. The strata maintain a regularity of dip at this distance, proving a submarine area of about 70 sq. miles. How much further the coal field extends seawards is unknown, but the indications are that it extends far beyond the present economical working limit and in all probability there is a vast submarine coal field. The productive coal measures are of Carboniferous age, these being underlaid by beds of sandstone, locally classed as millstone grit, which define the southern limit of the field,, while a spur of syenitic hills cuts off the coal-bearing strata on the north. Two main anticlinal folds having a general course easterly divide the field into three basins named from north to south: Sydney Mines-Lingan, Glace Bay and Morien.

Jan 1, 1929

By M. N., Short

TIE Pioneer mining district, better known as the Superior district, from its principal town, is located in Pinal County in south-central Arizona about 80 miles east of Phoenix and 22 miles west of Miami. The region embraces a confused series of mountain ranges of moderate FIG. I.----SUPERIOR, LOOKING NORTH FROM SOUTH BANK OF QUEEN CREEK. MAGMA MINE IS INDICATED BY WASTE DUMP IN GULCH TO RIGHT OF CENTER. height but precipitous slopes, between which lie irregular valleys filled with alluvial detritus. The average elevation is about 2800 ft. in the valleys and the summits of the ranges reach 2000 ft. above this. Superior is situated on the north bank of Queen Creek where it emerges from one of those ranges into a more or less basin-shaped valley. The drainage of Queen Creek is to the southwest and the flood waters spread out and lose themselves in the desert northeast of Florence, the county seat of Pinal County.

Jan 2, 1926

By W. R. Crane

The support of roof in mines is dependent largely on the character of the top rock and its occurrence. The formations overlying the orebed in the Birmingham district are sandstone and slate. The sandstone occurs in beds of sufficient thickness to constitute important elements in the system of support; the slate is relatively strong but is thinly stratified. The alternating beds of sandstone and slate furnish an excellent combination in that the former are strong and the latter are impervious; however, their continuity is broken by jointing or slip planes. The thickness, and consequent weight of the overlying formations, is important in so far as the size and arrangement of pillars are concerned but may be relatively unimportant, temporarily at least, as a factor in the support of the roof. The position of the respective beds of sandstone and slate, their relative thickness, and their inherent weakness because of the occurrence of faults and folds, may exert a predominating influence on their support in place, which is affected only in part by the weight of the cover. The only mine in this district that operates under a cover of approximately 2000 ft. (1900 ft.) is the Shannon so-called "twin slope," situated 14,000 ft. southeast of the portal of the No. 7 mine of the Tennessee Coal, Iron, & Railroad Co. The conditions in this mine indicate what may be expected in other mines when the same depth is attained; in fact, the effect of pressure is shown in several mines that have not reached two-thirds of that depth. It is evident, then, that conditions affecting the support of roof will not improve but rather will become more difficult with the extension of the mines into the valley under a constantly increasing weight of cover. Further, the difficulties will probably be augmented by the occurrence of faults and other disturbed ground, the presence and position of which at present are largely unknown.

Jan 1, 1925

By C. G. Fink, E. P. Polushkin

A PART of the material incorporated in this paper was derived from the studies of ancient metal objects examined by the authors from time to time for museums and art collectors, in order to verify the age of the metal. The data thus accumulated during several years were systematically surveyed and supplemented by new material obtained in examination of a set of specimens that had been generously donated by museums for this study. Altogether over 50 pieces were investigated, of which 39 are described in this paper. Every specimen is at least 1500 years old; the majority are considerably older. Exact conditions to which these bronze and copper objects were exposed in the ground are unknown, unfortunately. It is safe to say that exposure conditions did not remain constant during the long period of burial. Although the collection of specimens studied represents a wide variation in location and age of the objects, as well as in the nature and composition of the metals, it was found that fundamental changes in the metal structure were limited to a few typical cases which, therefore, may be considered as more or less general. The authors' chief aim was to study the effect of extremely long periods of corrosion on the structure of bronze and copper. Specimens Studied As the majority of specimens were very small and sometimes had a heavy coat of patina, or crust, which further reduced the amount of metal available for analysis, quantitative chemical analyses were not made. Small detached specimens were not always obtainable and studies had to be made on the statue, or other object, itself. In the description of specimens (Table I), their approximate compositions determined under the microscopc are given. The proportion of tin in bronze containing eutectoid was found by visual estimation of the area occupied by the eutectoid. It was based on the assumption that maximum solubility of tin in copper on moderately slow cooling is 7 to 8 per cent in thin castings and 9 to 10 per cent in heavy castings. When the metal was all

Jan 1, 1936

By Selma Hermann

For the past century, the so-called aluminum bronzes have been assuming a role of ever-increasing importance in the metallurgical field. The last quarter of that century has marked many efforts to find alloying elements that would alleviate some of the undesirable qualities of the aluminum bronzes-for example, the heterogeneity of the alpha solid solution and the extreme hardness of the beta. Much of this work, however, has been rather haphazard-compositions and heat treatment are usually so much at variance as to make comparison impossible. It is the object of this research to study the effect of certain percentages of common alloying elements on aluminum bronzes of analogous compositions and heat treatments. It is hoped that the material gathered here will at least serve as a basis for further systematic study.

Jan 1, 1930

By A. M. Gow

THE trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed, and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling.

Jan 1, 1930

By Anthony Folger, Howard R. Lowe, J. F. Dougherty, E. G. Trostel, Joffre Meyer

The status of the natural gas industry in Alberta, Canada, is described with particular reference to the current extent of natural gas reserves and possibilities for additional development. Certain major fields are discussed as representative of the types of gas accumulations within various broad geographical divisions of the provinces. The estimation of the future performance of a gas reservoir is discussed as the basis for an estimate of the future availability of natural gas from presently known reserves. The future availability of the provincial reserves and the estimated future demand for gas within the province are described. INTRODUCTION This paper is a condensation of a detailed study of the natural gas reserves and the future availability of pipeline gas in the province of Alberta as prepared for Trans-Canada Pipe Lines Limited and presented in public hearings at Edmonton and Calgary before the Petroleum and Natural Gas Conservation Board of the Province of Alberta. The study began in October, 1950, and resulted in the preparation of five volumes of data at the expenditure of more than 20,000 man-hours. This paper is designed to afford a broad picture with detail limited to a type example of both natural ga-accumulation and future availability of gas supply. The province of Alberta has an area of 255.285 square miles which, for sake of comparison. is 8,359 square miles smaller than the state of Texas. Natural gas was first discovered in 1883 at the now abandoned Alderson well located some 20 miles southeast of the town of Princess. The first gas in commercial quantities was found at Medicine Hat in 1890. During the last 68 years. 187 localities have been discovered which are capable of gas production, and 73 per cent of these have been found since 1945. Sixty fields currently are producing gas, including 22 non-associated gas accumulations. Location of the oil and gas fields and prospects in the province of Alberta is shown in Fig. 1, together with a list of the localities of measurable gas, Fig. 1A. The estimated total provincial gas reserve as of Jan. 1, 1952, for the 104 fields estimated, is 11.7 trillion cu ft proved and probable, and for the 187 known areas capable of production is in excess of 16 trillion cu ft on a total proved, probable, and possible basis. Five fields (Pincher Creek, Leduc-Woodbend, Viking-Kinsella, Cessford and Medicine Hat) are estimated to have recoverable reserves of more than one trillion cu ft each. A sixth field, Turner Valley, was initially in this group, but its reserves have been depleted substantially. Twenty-four fields, of which the above mentioned six fields are a part, have estimated gas reserves (including the possible category) in excess of 100 billion cu ft. These 24 fields account for 79 per cent of the total provincial reserves. Comparative systemic analyses reflect that 56 per cant of Alberta's gas reserves are contained in sediments of Cretaceous age; 30 per cent in sediments of Mississippian age; 10 per cent in sediments of Devonian age; three per cent in sediments of Triassic age; and the remaining one per cent in Jurassic and Permo-Pennsylvanian sediments. It is expected that the relative importance of the Mississippian, Devonian, and Triassic sediments will be increased as exploration progresses. GENERAL GEOLOGY The western Canada basin comprises the sedimentary area between the Canadian Shield and the Rocky Mountain Front Range, the Arctic Ocean, and the International Boundary. The basin has an approximate area of 765,000 square miles and embraces parts of the provinces of Manitoba. Saskatchewan. Alberta, British Columbia and the Northwest Territories. Generalized columnar sections for the Province of Alberta are shown in Fig. 2. Substantially all of Alberta, except its northeast corner, has sedimentary cover. Sediments of all the geologic systems are represented. except those of Silurian age.

Jan 1, 1952

By George Fowler

THE history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur Co. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico.

Jan 1, 1934

By E. H. Bunce, H. M. Haslam

The "direct process" for the manufacture of pigment zinc oxide produces the oxide directly from ore. This is accomplished by reducing the zinc by means of carbonaceous fuels and immediately burning the evolved zinc vapor to zinc oxide. For many years this was done by smelting a loose charge of ore and fuel on perforated grates. Since this process was developed in America and was extensively used here, it has become known as the "American process." Alternative methods of producing pigment zinc oxide are the "indirect process " and the "wet process." In the indirect process the raw material is metallic zinc, which is volatilized and burned to the oxide. For a long time this has been done in externally fired horizontal refractory retorts. This process has become known as the "French process," from the country of its origin. The wet process precipitates the carbonate or hydrate from zinc-bearing liquors and then calcines the precipitate. This method has been but sparingly used for producing commercial quantities of zinc oxide. It appears to be advisable to restrict the use of the terms "American process" and "French process" to the methods of the earlier periods and to consider the terms "direct process" and "indirect process" as generic terms to designate, first, all methods of producing pigment zinc oxide directly from ores, and, second, to include all those methods of producing zinc oxide from metallic zinc and metallic zinc-bearing substances. American Process In 1796 John Atkinson was granted British Patent No. 2094/1796 entitled, "Manufacture of White Paint." This patent describes a method of producing zinc oxide in which roasted zinc blende or calcined calamine is mixed with charcoal, and the mixture heated in a muffle to liberate zinc vapor, which is then burned to obtain zinc oxide fume. About 1850 The New Jersey Zinc Co., at its plant in Newark, N. J., attempted to make zinc oxide by smelting, in a reverberatory furnace, a mixture of coal and ore from its Franklin mine. A considerable amount

Jan 1, 1937

By A. M. Gaudin

THIS paper presents, with the help of colored photomicrographs, the new method of mineral identification termed "selective iridescent filming." This method pertains to the field of determinative mineralogy, which it provides with tools for: (1) phase identification, (2) solid solution analysis. The method should be particularly useful in the applied fields of: (1) paragenesis of ore deposits, (2) mineral dressing, (3) mineral synthesis and study of phase equilibria.

Jan 1, 1938

Jan 1, 1906

By Edmund Davenport

THE specific aim of this work has been to study certain forms of internal deterioration which occur in tungsten filaments when subjected to high temperatures under various conditions, and to determine the cause of such deterioration. This would naturally lead to a consideration of methods of control or means of prevention of the phenomena. The deterioration was first noticed as a peculiar condition in the grain boundaries of certain tungsten filaments which had been burned? for long periods in lamps. In these cases it was noted that the grain boundaries contained a number of minute black dots which were at first thought to be non-metallic inclusions. It was demonstrated later that these dots or pits, as they were designated, could be readily produced by burning filaments in an atmosphere of flowing hydrogen. This method was convenient and adequate for the purpose, and was adopted for most of the work discussed in this paper. The evidence accumulated to date indicates that these pits are actually small voids between the grains. The purpose of this paper is to present- the information on this interesting subject gathered during a period of about 3 years. As applied to tungsten, the subject appears to be of considerable importance, experience having shown that this pitting ?is frequently associated with poor performance of filaments in lamps. The question has arisen as to whether these intergranular pits are peculiar to tungsten, or if they occur in all metals. If they are found iii all metals, the facts will be of considerable theoretical interest, as the material at the grain boundary plays an important part in most of the current theories of the properties of metals and alloys.

Jan 1, 1927