Search Documents

By Y. Kondo, S. Yamazaki, Z. Asaki

Thermal deco7nposition of Pyrite particles in a fluidized bed with inert gas stream was studied. Assuming that heat transfer from the surroundings to the fluidized particles controls the overall decomposition rate, rate equations for the batch process and for the continuous process were derived. In the batch experiment, a linear rate equation satisfies the experimental results and the overall heat transfer coefficient calculated from the rate constant agrees fairly well with that obtained by Leva.l1 For the continuous process, two rate equations were derived, one on the assumption of complete mixing of particles and another on the upward piston flow of particles in a fluidized bed. The former holds for a bed containing a higher fraction of decomposed pyrite realized at lower feeding rates. The latter can be applied for a bed at higher feeding rates. Thus, segregation of particles in the fluidized bed was indicated at higher feeding rates. Bed temperatures also correspond to these conditions. ThERMAL decomposition of pyrite may be represented by Eq. [I]. The pressure of diatomic sulfur gas reaches 1 atm at about 690°C. The thermodynamics,' kinetics,2'3 composition, and properties3-5 of decomposed products of such a reaction have been studied. Pyrite is a very common sul-fide mineral and is often accompanied with other sul-fides. It is of basic interest in nonferrous metallurgy to clarify the behavior of pyrite in the pyrometallur-gical processes of sulfide minerals of metals such as copper, lead, zinc, nickel, and so forth. Interest in this reaction increased recently because of possible elimination of arsenic from pyrite in processing highly purified iron oxide pellets. Producing elemental sulfur from pyrite, instead of sulfuric acid, also aroused interest in this reaction. It is indicated that the thermal decomposition of solid particles, such as calcium carbonate, proceeds through three major sequential steps: heat transfer, interfacial chemical reaction, and mass transfer.637 It is known that the decomposed product of pyrite is very porous2, 3 and the diatomic sulfur gas evolved can easily escape through this layer of decomposed product. It depends upon the circumstances, therefore, whether the heat transfer to the interface within particles or the chemical reaction at the interface determines the overall decomposition rate. The enthalpy change in the decomposition of pyrite is about 33 kcal per mole FeS2 which is comparable to that of calcium carbonate. The decomposition of calcium car- bonate becomes more and more dependent on the rate of transport of heat when reaction temperature increases, such as occurs in a fluidized bed.6'7 It is reasonable to presume, therefore, that the thermal decomposition of pyrite, an endothermic process, carried out in a fluidized bed may be analyzed according to the heat transfer controlling model. This work intends, first, to propose a mathematical model that determines the overall rate in a fluidized bed for the decomposition process and, second, to investigate a few characteristics of the fluidized bed based upon the experimental results obtained. KINETICS OF THERMAL DECOMPOSITION IN A FLUIDIZED BED It is intended in this section to obtain rate equations for thermal decomposition of pyrite in a fluidized bed by assuming that the overall rate is determined by heat transfer from the surroundings to the particles. Both batch and continuous processes are considered. 1) Batch Process. To obtain the rate equation in the batch process, the following two additional assumptions are made. First, the temperature of preheated inert gas, tg, blown into the fluidized bed is assumed to be the same as the temperature of the fluidized bed, tf. Thus, no heat exchange occurs between the gas and particles in the bed and only the heat transfer from the reactor wall kept at tw to the particles is to be considered. Second, the decomposition is assumed to start at the outer surface of the particles and to proceed toward the center. At any given time during decomposition, undecomposed pyrite remains in the tori at a temperature: td. The decomposed shell is composed of FeS1+x whose outer surface is at tp Diatomic sulfur gas evolving at the interface is heated to tf during its escape through the decomposed shell. This is illustrated in Fig. 1. With the above-mentioned assumptions of heat transfer, we have:

Jan 1, 1969

By J. C. Fisher

Martensite transformations in steels and other alloys are characterized in part by the absence of composition changes during the growth of a new phase. Transformation occurs rapidly, and there is insufficient time for long range diffusion or partition of alloying elements to take place; martensite reactions in alloys thus are similar to phase transformations in single component systems. A fundamental understanding of martensite transformations in steels is impossible without knowledge of the free energy change upon transforming austenite (face centered cubic iron containing alloying elements) to ferrite (body centered cubic iron containing alloying elements) of the same chemical composition. The present paper assembles the best information available concerning the influence of temperature and composition on this free energy change. Most of the material has been taken from the work of Johansson,' Mehl and Wells,2 Zener3,4 and Smith;5 and indirectly, through these authors, from the work of Austin.6 In agreement with the generally accepted viewpoint, martensite is assumed to be an ordered solution of carbon in ferrite of the same composition as the parent austenite; only at high temperatures and low carbon concentrations is the carbon in ferrite distributed at random. The properties of the disordered solution are estimated by extrapolating the known properties of iron-carbon solid solutions into the range of supersaturation, and the free energy change associated with ordering is estimated from the theory developed by Zener. By incorporating Smith's recent thermodynamic measurements and Zener's theory of ordering, the present analysis modifies previous estimates of the free energy change associ- ated with martensite transformations. Consider a two component system consisting of a solvent A and a solute B. Let Na and Nb represent mol fractions of A and B respectively, let aa = raNa and ab = YbNb represent activities, and let superscripts 1 and 2 refer to phases 1 and 2. The partial molal free energies of A and B in phases 1 and 2 can be summarized as follows: free energy standard state Fa' - Fao1 = RT In an1 pure A' Fa2 - Fa2 = RT In aa2 pure A2 Fb1 - Fbo = RT In ab1 pure B Fs2 - FB2 = RT In aB2 pure B. The free energy of a gram atom of phase 1 is* AF1 = Na'Fa1 + Nb'Fb1 and that of phase 2 is AF2 = NA2FA2 + NB2Fb2. A martensite transformation from phase 1 to phase 2 requires Na1 = Na2 = Na and NB1 = NB2 = Nb, and the free energy change per gram atom accompanying transformation is AFi-2 = NA(Fa2 - Fa1) + Nb(Fb2 - Fb1) = NA[RT In (aA2/aA1) + AFa1?2] + Nb RT In (aB2/aB1) = Na[RT In (ra2/ra1) + AFa1?2] + Nb RT In (TaVTB1). [1] where yn2, yn1, yB2, yB1 are activity coefficients, and where Ma'+* is the free energy change upon transforming a gram atom of pure A from phase 1 to phase 2 at the temperature in question. For martensite transformations in plain carbon steels, A = iron (Fe), B = carbon (C), 1 = austenite (7). 2 = ferrite (a), and Eq 1 is AFr ?a= NFe[RT In (rf.a/rfer) + AFF.r?a] + TVc RT In (eca/rc1)- L2] Nothing is known concerning the values of yFea and yca for carbon concen- , trations in excess of 0.025 pct. However, the approximation rf.7 = 7f." = 1 cannot be appreciably in error for small carbon concentrations, and Eq 2 reduces to Afr-a = NfeFfer?a1 + NC RT In (rca/rcr)- [3] Johanssonl and Zenera have calculated MFfr?a from the specific heat measurements compiled by Austin.6* Their calculated values agree closely, and are summarized in Table 1. The activity coefficients relative to graphite for carbon dissolved in iron vary with temperature according to the relationships d In rcr/d(1/T) = AHcr-R dlnyca/d(l/T) = AHCa/R where AHc? and AHca are the heats of solution of graphite in y and a iron. Assuming the values of AH to be independent of carbon concentration and temperature, In rCr = AHcr/RT + I1 In rca = AHCa/RT + 12

Jan 1, 1950

By R. C. Buehl, M. B. Royer

High manganese slags of low phosphorus and iron content are produced by air oxidation of high phosphorus spiegeleisen in a basic-lined converter. Control of phosphorus and iron within specification limits for ferromanganese ore feed is obtained by a unique cyclic operating procedure. Various types of slags, or synthetic manganese ore, can be made. AN affiliated paper' describes the production of high phosphorus spiegeleisen containing 14 to 23 pct Mn and up to 4 pct P in an experimental blast furnace from open-hearth slag or manganiferous iron ore. This phosphorus content is too high for use of the spiegel in normal steel-production operations. Consequently, a preferential separation must be effected whereby the manganese is concentrated in a product that is usable in industrial operations. The preferential separation methods being investigated for this phase of the work are confined to pyrometal-lurgical processes for ready incorporation into steel-plant operations. It is fortunate that manganese is more actively oxidizable than iron or phosphorus, and therein lies a preferential separation method for isolating manganese from these two elements. Silicon is more strongly oxidizable than manganese, and its oxidation precedes, or occurs simultaneously, with manganese. Therefore, manganese and silicon are separable into a high manganese oxide slag phase while the phosphorus and iron remain in the molten metallic state. Complete separation of these elements represents an ideal condition which is not generally attainable in actual operations. This pyro-metallurgical method for separating manganese from phosphorus and iron by preferential oxidation was investigated by blowing 500 lb of metal in a basic-lined vessel to obtain preliminary information on the effectiveness of the procedure. Certain conditions of attainment in the separation process are desirable in any method for removing manganese from high phosphorus spiegeleisen, such as: 1—High recovery of manganese in the oxidation product; 2—the product to be of equal or better quality than ferromanganese-grade ore—48 pct Mn minimum, less than 10 pct SiO2, and Mn-P ratio of 300:1; and 3—attainment of the enumerated objectives in a product amenable to industrial handling, such as a slag of high manganese content that will flow from the processing vessel and of sufficient fluidity for ready separation of metallic granules that may have become mixed with the manganese slag phase. Previous Work Recovery of manganese from low grade ores and industrial byproduct slags by smelting to spiegeleisen, with subsequent oxidation to synthetic ferro-manganese-feed ores, has been a subject for periodic investigation during the past four or five decades in the United States and Germany. Joseph' and associates of the Bureau of Mines North Central Experiment Station, Minneapolis, Minn., smelted manganiferous iron ores of the Cuyuna range, Minn., to spiegeleisen and subsequently tried air and ore oxidation procedures for concentrating the manganese into synthetic ferrograde manganese ore. Joseph's results on the operation of a side-blown basic-lined converter for air oxidation of manganese from molten spiegeleisen were so discouraging that the procedure was abandoned after 11 blowing tests. Much slag was thrown from the converter vessel; phosphorus content was four to five times the maximum allowable for ferro ore; and a manganese-iron ratio of only 2 or 3:1 was obtained in the slag instead of the required 8:1. Oxidation of manganese from spiegeleisen with about 0.5 pct P, by adding iron ore to molten spiegel in an experimental open-hearth furnace, proved moderately successful in Joseph's experiments. The main drawback to the operation was the necessity for over-oreing for effective oxidation of the manganese with consequent too high iron oxide residual in the slag. Furthermore, the phosphorus content was proportional to the iron concentration and therefore much too high, so that several hours of reduction by a carbonaceous material were required to adjust the iron and phosphorus to the desired content of high grade ferro feed. A troublesome feature of the slag product of the spiegel oxidation process was its lack of fluidity if the silica content was less than 10 pct, the concentration considered desirable for the synthetic ore. Approximately twice the desired concentration of silica was required to impart enough fluidity for transfer from the vessel by pouring. The acute shortage of manganese in Germany

Jan 1, 1953

By E. S. Anolick, Joseph Singer

The magnetic after-effect, in the form of time decay of permeability (l/µ), has been used to obtain independent data on the solubility of' carbon in pure iron. The results differ slightly from the solubilities obtained through internal -friction experiments. The mechanism of the time decay being the magnetic analogue of internal friction, it appears necessary to explain the observed discrepancies, and some suggestions are made. THE purpose of this work was to establish the reliability of the time decay of permeability as a measure of dissolved interstitial in the body-centered-cubic lattice, and further, to establish techniques suitable for such measurements with samples of a form convenient for various other measurements. This particular sample form was the "epstein" strip, i.e., 25 cm by 3 cm by 0.035 cms. While the general conclusions are not limited by this geometry, there are two aspects of the samples that may be relevant: a) texture, and b) grain size, which ranged generally from 1 to 10 mm. Effects due to these two possible parameters were thought to be small and were not investigated. Calibrating the time decay technique and the other experimental procedures by measuring the solubility of carbon in pure iron suggested itself because of the accumulation of data on this subject through the related technique of the internal friction'; The essentials of this report have been published in a somewhat condensed form.5 Since then some additional data have been taken. It is the purpose of this paper to add these data and to provide more complete description of the experimental techniques than was possible then. The time decay of permeability is a form of the magnetic after-effect.6,7 Permeability is measured immediately after demagnetization (µº) and also long after (µ8). The time decay, ?(l/µ), is the difference 1/µ8 - 1/µ0 and has been considered to be proportional to the concentration of a dissolved interstitial6,8,9,12 The relaxation time! 7, is characteristic of a particular diffusion, and affects the permeability as follows: where he being the activation energy for diffusion of the interstitial. Reference is made to the works of snoek6 and Neel7 for a complete discussion. A brief exposition of the principal ideas may be in order here, as follows. On the basis of the simplest model, resistance against domain wall motion increases with time after demagnetization due to the diffusion of interstitials to preferred sites created by the magnetostrictive tetragonolization under the strong magnetic field. Thus permeability, measured with a small field after the abrupt removal of the large field, will continuously fall with the process of diffusion of the interstitials, and the total "time decay" (or "time decrease") should be proportional to the amount of interstitial in solid solution. In the present report, use is made only of the total time decay rather than of the nature of the progress of the decay; the only problem involved in this approach is the need for assurance that only one interstitial is contributing to the effect as used. It is felt that the special use made here of the total time decay warrants the conclusions. Other work has been going on elsewhere on the detailed study of the nature of the time decay.8'9 EXPERIMENTAL A) Materials—12-lb ingots were made in a vacuum furnace from high-purity iron and by a series of hot and warm reductions were brought down to 14-mil strip. This was cut into 25-cm epsteins. The pure iron was decarburized at 750 °C by hydrogen. The time decay measurement for the decarburized iron (see below) indicated a satisfactorily low starting level of interstitials. Grain growth to grain sizes of 1 to 10 mm was produced in the pure iron by a 700" anneal in hydrogen after a critical reduction of about 7 pct as suggested by previous trials. No measurement of texture in the pure iron was made. The grain size was taken to be large enough to be beyond any sharply critical size regarding solubility. B) Infusion of Carbon—Since the permeability measurement required about two dozen epsteins, a special method of carbon infusion had to be developed to ensure homogeneity of infused carbon. This was accomplished by setting the samples edgewise in a

Jan 1, 1961

By O. R. Morris, G. L. Hawkes

A galvanic cell, using as electrolyte a fused salt solution of calcium carbide and as electrodes carbon and a Fe-C alloy of known composition, has been set up to study the thermodynamics of Fe-C alloys in the temperature rmzge 800" to 1000°C. Time independence and reproducibility of the cell electromotive force were taken as evidence of the reversible behavior of the cell. Carbon was believed to be present in the electrolyte as the so-called acetylide ion, C;-. The plots of the cell electromotive force us temperature for a specific alloy composition were straight lines within the limits of experimental error. The average Partial molar enthalpy of carbon in iron relative to pure carbon was found to be +10,610 i 93 cal per g-atom C. Thermodynamic analysis of the data has led to the following equation for the carbon activity, ac, based upon pure carbon as the standard state: In ac = In Zc + 10,560/RT + (10.02 + 77O/T)ZC - 2.350 where ZC is the lattice ratio [nC/(nF, - nc )] and T is the absolute temperature. This equalion gives carbon activity values generally slightly lower than those from gas equilibration studies reported in the literature. METAL LOGRAPHIC examination of a polished cross section of the steel anode used in the electrolysis studies of fused salt solutions of calcium carbide by Morris and Harry revealed extensive carburization of the steel by the electrodeposited carbon. This carburization was reflected in the variability, with time, of the applied potential to the electrolysis cell, necessary to maintain a constant current density at the electrodes. This observation suggested the setting up of a galvanic cell of the "alloy concentration" type to study the thermodynamics of some metal-carbon alloys. Cells of this general type have been widely used for the study of alloy systems.2 In view of the availability of published data in respect of the austenite phase of the Fe-C system, it was decided to carry out measurements upon these alloys before proceeding to studies of less well documented systems. The galvanic cell may be written: where [C] is carbon dissolved in iron. The electrolyte was a fused salt solution of calcium carbide, containing some 5 to 10 mol pct of carbide. The cell reaction is believed to be: C(s)-[CI [I1 Carbon forms an interstitial solid solution in iron, with the atoms located in the octahedral interstices. In the fcc crystal structure of austenite there is one octahedral interstice per iron atom. Thus, the lattice ratio, ZC, shown by Gurney3 to be the fundamental concentration parameter in the context of interstitial solutions, is given by: where nc and nFe are the number of carbon and iron atoms, respectively. chipman4 has recently shown empirically the advantages of using this concentration parameter instead of the more usual atom ratio or atom fraction. The cell electromotive force, E, assuming reversible behavior, is related to the carbon potential or the partial molar free energy of carbon in the solid solution relative to pure carbon at the same temperature and pressure, GP at the composition ZC, by the equation: where z is the carbide ion valency and F is the Faraday constant. An activity of carbon, ac, in the solution relative to the value of unity assigned to pure carbon, and an activity coefficient, qC , are defined such that: where R is the gas constant and T the absolute temperature. GF is further related to the relative partial molar enthalpy Hm, and the temperature coefficient of the cell electromotive force, (aE/aT)Zc, by the equations: Measurement of the cell electromotive force thus enables calculation of the relative partial molar thermodynamic properties of carbon in iron, if z is known. At E = 0, the solid solution is in equilibrium with pure carbon. More convenient for many purposes is the standard state based upon the infinitely dilute solution, Henry's law. The relationship between the activity coefficient of carbon based upon this standard state, and that based upon the pure carbon standard state, qC , may be obtained by considering the free energy of transfer of carbon from the latter standard state to the former. The relationship is: where +:H is the activity coefficient of carbon in the hypothetical standard state based on a reference of

Jan 1, 1969

By Reynold Q. Shotts

CHEMICAL methods, based on the relative rates of oxidation of fusain, bright coal, and dull coal by nitric acid, have been devised to determine these coal components.1-4 Results obtained by oxidation methods for fusain have been checked against results obtained from microscopic methods5, 6on duplicate samples of the same coals, but to the author's knowledge this has not been done for bright and dull coal components. For this reason it is not certain that the two methods of analysis identify essentially the same chemical or physical units. It would be highly desirable to see results of the application of both methods to duplicate samples, but in the absence of any such data the author has attacked the problem indirectly. From the U. S. Bureau of Mines samples were obtained of three Alabama coals which the USBM had analyzed optically and reported on over the past 30 years. These samples were subjected to analyses by oxidation rate methods. Results of this work, and comparisons with the USBM analyses, have been published." This was the first indirect approach to the problem. The present report attempts a second indirect approach by way of internal validation. By nitric oxidation samples of two whole coals were carefully analyzed for fusain, bright coal, and dull coal. One coal was analyzed in duplicate. Duplicate portions of each of the coals were divided into three density fractions by means of heavy liquids. A duplicate portion of one of the coals was divided by sieving into three size fractions. Each fraction was analyzed by oxidation and its percentage composition calculated in terms of fusain, bright coal, and dull coal. Because the weight percent of each fraction was known, a material balance calculation for the whole coal was also made. The resulting reconstituted analysis of the whole coal could be compared to that determined by direct analysis. In addition, specific reaction rate constants were determined for each component and for each whole coal or fraction. Arbitrary reactivity indexes were calculated by dividing by 100 the sum of the products of the percent of each component in the coal and its specific reaction rate constant. The resulting figure was an average reactivity index for each coal or fraction. Weighting the reactivity indexes for each fraction by the percent of the fraction in the coal gave a reactivity index for each whole coal which could be compared to that calculated directly from the whole coal analysis. If oxidation analyses really delineate definite physical entities within the coal, or even definite groups of similar entities, reconstituted analyses calculated from fraction analyses should check closely those made of the whole coal. It probably is true that optical methods identify and describe a greater variety of components than do chemical methods and that variations are wide in the appearance and quantity of those components identified optically. Chemical methods based upon differences in oxidation reaction rates would of necessity be less discriminating, as between similar components, than would optical methods. The procedures followed for oxidizing the samples, analyzing the residues, plotting and calculating the percentage of each component, and calculating its specific reaction rate constant have been fully described.'-' In brief the method originally proposed by Fuchs et al.1 for the determination of fusain consists of the oxidation of small samples of coal in boiling 8N nitric acid in a condenser-fitted flask. After boiling for periods of 1/2 to 4 hr, the unoxidized residue is filtered and washed. The washed residue is treated with normal sodium hydroxide, diluted, and allowed to stand for several hours. The resulting brown liquor is removed, and the filtered residue dried, weighed, ignited, and weighed again. The ash-free residue is expressed as a percent of original dry, ash-free coal. The percent residue is plotted against time, and the extrapolation of this line to zero time gives the percentage of dry ash-free fusain present in the original sample. The shape of the resulting time plots has been explained' by the assumption that they are the result of two different types of reaction, the first part representing a first order reaction with rate a func-

Jan 1, 1956

By D. R. Wieland, A. N. Barron, A. R. Hendrickson

A definite relationship has been found between the reactivity of flowing hydrochloric acid and its shear rate in a carbonate fracture. Both flow velocity and fracture width affect the acid reaction rate. Laboratory studies were conducted on acid reactivity at different flow velocities through horizontal-linear fractures, using 15 per cent hydrochloric acid at 80' F and approximately 1,100 psi. Fracture width varied from 0.02 to 0.20 in. These data provide a new basis from which the spending time and penetration of the acid can be estimated. Equations were derived expressing the relationship between injection rate, fracture width, acid concentration, time and fracture height, for linear and radial fracture systems. Because the penetration of the acid before spending is closely related to the extent of productivity increase resulting from an acidizing treatment, these data provide a valuable insight into some of the controlling factors that must be taken into consideration during treatment preplanning. INTRODUCTION Acidizing of carbonate reservoirs to improve production characteristics has been widely practiced since 1932. Originally, it was assumed that the acid uniformly penetrated natural formation pores and flow channels, enlarging them and thereby increasing their flow capacity. Little consideration was given to the reaction rate of the acid, or how far it would penetrate away from the wellbore into the formation, before spending. It has been shown recently' that, unless fractures are present in the rock, very little penetration is attained before spending, and the benefits of the acidizing treatment are largely confined to the immediate vicinity of the well-bore. Therefore, acid treatments may be classified into two categories: (1) matrix acidizing, in which the acid flows through multiple: formation pores; and (2) fracture acidizing, in which the bulk of the acid travels through fractures in the rock, whether natural or induced. When acidizing treatments are conducted at pressures of sufficient magnitude to open and extend such fractures, it is often desirable to inject a propping agent to hold the fracture open after the treating pressure has been released, thus providing a highly conductive flow channel through the rock. In some cases where acid attack produces surface irregularities, the resulting flow passages can be sufficient to provide high conductivity without use of a propping agent. During injection, the acid dissolves the carbonate rock with which it comes in contact until it is spent. Deeper penetration of the spent acid into the formation produces no appreciable benefit (if no propping agent is used) because the unetched fracture faces will rejoin when treating pressures are released and the fracture will "heal", with negligible resultant conductivity. The spending time of the acid thus becomes important in determining how far from the wellbore the improved-conductivity zone extends. The spending time of acid after injection into carbonate rock depends on the rate at which the acid reacts with the rock. This in turn is controlled by a number of factors, as previously reported. 2-4 These include temperature, pressure, acid concentration, rock composition, injection rate and the area-volume relationship between the acid solution volume and the surface area of the formation flow channels through which it penetrates. Thus, in matrix acidizing, where an extremely large area is exposed to the acid, spending is rapid. In contrast, spending time is prolonged in open fractures, where the area-volume ratio is much lower. Thus, greatest penetration of the acid before spending will be achieved in acid-fracturing treatments where fractures are held open by hydraulic pressure. Perkins and Kern5 have presented equations for fracture-width determinations which, for hard formations such as limestone or dolomite, indicate that high injection rates and viscous fluids are required to create wide fractures. Increasing the injection rate will, in itself, produce faster reaction rates. Because this type of reaction can be considered to be first-order diffusion-controlled, '-' the rate of movement of fluid past the rock surface affects the thickness of the diffusion layer, in turn affecting the reaction rate. Staudt, et al,10 report the results of tests in which a rotating marble cylinder was immersed in acid, and the weight loss at different speeds determined. Such test conditions, however, are not truly indicative of the situation in a formation during an acid-fracturing treatment. This paper reports reaction-rate data obtained under

By J. T. Norton, Pekka Rautala

The phases and equilibria in the W-Co-C system have been studied by X-ray diffraction methods, metallographic technique, and thermal analysis. In addition to the 7 phase, two double carbides, called 8 and have been revealed. The compositions correspond to CO3 W6C2 and Co3-W10C4. The reactions leading to these phases have been explained and tentative diagrams of stable and metastable equilibria proposed. The basic reactions in sintering cobalt cemented tungsten carbides are discussed. THE W-Co-C system is of fundamental importance in practical carbide manufacturing as well as for the understanding of the sintering mechanism. Surprisingly little is known about this system, for the probable reason that all the important alloys are of two-phase structure and that the diagram Co-WC has been treated as a quasi-binary. This obviously is incorrect, because WC decomposes before melting. One ternary phase, 7, of composition Co3W3C has long been known. It was first studied by Adelskold, Sundelin, and Westgren,1 although the isomorphous iron-tungsten carbide was known earlier. There have been in the literature several reports of two 7 phases.' " Also the 7 phase has been considered unstable by Takeda4 and Westgren.1 The Co-WC diagram has been studied by Wyman and Kelley5 and a quasi-binary diagram has been published by Sandford and Trent.2 Takeda has published a tentative Co-W-C diagram, considering both metastable and stable equilibria. However, the lines of two-fold saturation are shown only partially and it seems impossible to complete the diagram without violating the phase theory. Therefore it seemed desirable to examine the system in more detail. Experimental Procedure The alloys used in the present investigation were made of powders of tungsten, tungsten monocarbide, cobalt, and carbon and were of the grade used in manufacture of commercial cemented carbides. The powders were ground and mixed in small stainless steel ball mills, using balls of the same material. Benzene was used as a dispersing agent. The mixing period was 1 hr, since this was shown to give suffi- ciently good mixing of the powders without too great a contamination from the mill. After ball milling, the specimens were pressed in cylindrical or rectangular dies. No paraffin or other lubricant was used and the small compacts had sufficient green strength to be handled without difficulty. Several sintering furnaces were employed. The most satisfactory arrangement was a vacuum furnace based on the Arsem principle which employed a graphite helix as the resistance heating element. Specimens were placed on graphite stands and there was generally a slight carburization or decarburiza-tion of the specimen surface, depending on the carbon content of the alloy. The evaporation of the cobalt at a sintering temperature of 1400°C was not significant, but became severe at 1500°C and higher. The sintering time was 1 hr at 2000°C and 2 to 4 hr at lower temperatures. It was not possible to quench the specimens, but the cooling rates were rather fast, greater than 300°C in the first minute. In the system under investigation, the reactions are sluggish, and it is believed that the high temperature structures are satisfactorily retained. The principal method of investigating the sintered specimens was X-ray diffraction by the Norelco recording spectrometer. Approximate determinations of the phase boundaries were made by the disappearing phase method. Ternary Phases To study the phase formation in W-Co-C system, a series of specimens was sintered at 1400°C. In this experiment two ternary phases, called here ? and k were formed in addition to the well-known 7 phase. The 7 phase, which has been completely described by Westgren: showed a range of homogeneity from 7 to 20 pct C and from 38 to 48 pct Co. At 1400°C the 7 phase was found to be in equilibrium with monotungsten carbide, 8, tungsten, 8, #?, and liquid. The boundaries toward #? and liquid were difficult to determine and appeared to be very temperature sensitive. The other boundaries are believed to be well fixed. The homogeneity range of 7, as measured in this work, is considerably smaller than the one

Jan 1, 1953

By E. S. Machlin

An extension of the thermodynamic theory has been made for the case of irreversible growth processes occurring by the motion of an interface. The theory is applicable to such diverse phenomena as diffusion, growth in recrystallization, continuous grain growth, growth of carbides, etc., growth of eutectoid products, growth in solidification, recovery, "slipless" flow, etc. THE publication of a recent book1 has served to focus attention on a very powerful means of treating certain irreversible processes. This method which has been formally described as the thermodynamic theory of irreversible processes is applicable to processes which involve an approach to equilibrium and for which the deviations from equilibrium are small. The irreversible processes can be classified into three groups: chemical reactions, transport processes (diffusion, heat and electrical flows), and relaxation phenomena involving a degradation of internal energy to more stable states. The limits of applicability of the theory can be precisely defined1,2 for each type of irreversible process. For example, in a chemical reaction at constant temperature and pressure, the Gibbs free energy released per mol in the process should be less than the thermal energy, RT. Another type of irreversible process, which sometimes involves a combination of the first two of the above-mentioned groups, is treated in this paper. This process is one characterized by the motion of an interface separating two regions having different values of free energy and may be briefly described as a growth process. Prigogine2 and Herring3 have treated special cases of this type of process. Previous conscious applications of the theory in metallurgy have been limited to the field of diffusion, one of the transport processes. Darken,4 Bardeen,5 Prigogine2 and others have made significant contributions in this respect. Some other applications of the theory are described in this paper. The Theory The thermodynamic theory of irreversible processes is based on the work of Onsager,6 DeDonder,7 Prigogine2 and others. A resume of the theory has been given by Prigogine2 and DeGroot.1 A brief description of the theory follows, although for a complete understanding the reader is urged to read the references. It is first assumed that the change in entropy, even for a system removed from equilibrium, is given by dS = [dU + pdV - Si µi, dn, - Sk Pk dxk]T-1 Using this expression, the irreversible entropy production in the system is calculated by subtracting the contribution to the change in entropy of the system by transfer of heat, work, or matter from the surroundings. Thus, for example, the irreversible entropy production of a system at constant temperature and pressure is given by dtS = — — dG (DeDonder7) Now it has been shown by Prigogine,2 DeDonder,7 and DeGroot1 that the rate of irreversible entropy production diS/dt, when calculated in the manner suggested, can be written as a sum of products of conjugate forces XK and fluxes Jk, i.e., d,s/ = Sk Jk Xk [I-1] dt The assumption is next made that a linear relation exists between a given flux and the forces, obtained from Eq. I-1, i.e., Ji = Sk Lik Xk (i = 1, 2, . . . n) [I-2] Generally, there is a degree of freedom in choice of the fluxes and forces. However, for all the choices consistent with Eq. I-1 the Onsager8 relations, based on the principle of microscopic reversibility, namely, Lik = Lki, are valid. The coefficients Lik, depending upon the choice of the conjugate fluxes and forces, may be more or less dependent upon the parameters defining the state of the system. In general, the proper choice of fluxes and forces utilizing Eq. I-1, makes the coefficients Lik independent of time. Also, because many of the three classes of irreversible phenomena have already been treated,1,2 a proper choice can be made by analogy. In any case, the validity of Eq. 1-2, from whatever choice made using Eq. I-1, must be tested by experimentation. The theory, thus, comprises the following steps: 1—The irreversible entropy production is calculated to yield Eq. I-1. 2—The terms in Eq. I-1 are grouped

Jan 1, 1954

By G. G. Hancock, H. H. Johnson

Hydrogen gas at atmospheric pressure is shown to cause substantial embrittlement in a martettsitic high-stretzgth steel. Subcritical crack growth is observed at very lom stresses and with high growth rates. It is suggested that an adsorbed layer of hydrogen atoms at the crack-tip surface provides the damaging hydrogen. Oxygen in small quantity, as little as O.7 pct by volume, is shown to eliminate subcritical crack growth in gas environments caused by hydrogen or water vapor. However, dissolved oxygen in water has little or no influence upon crack-growth rates. Oxygen-stopped cracks may be restarted by water, or by hydvogen or water vapor if oxygen is removed from the environment. These observations are interpreted in terms of preferential adsorption of oxygen at the crack tip and the formation of an oxide barrier. RECENT investigations1-3 have demonstrated that environmental factors are frequently responsible for delayed failure in martensitic high-strength steels. The environment causes crack initiation from preexisting cracklike flaws at unexpectedly low stresses, often far below the uniaxial yield strength. The crack then propagates at a rate controlled by the environment and the crack-tip stress-field intensity; during this period crack propagation will cease if either the stress or the aggressive environment is removed, and this may be considered a definition of subcritical crack growth. Fracture occurs when the crack has grown to a critical length, such that the fracture toughness of the steel is exceeded. Several liquids are known to cause delayed failure, but water and water vapor are the most severely damaging of the environments investigated to date.'-3 It has been suggested that hydrogen produced during corrosion reactions may be the actual embrittling agent2 The severe embrittlement caused by water vapor inevitably raises the question as to whether other gas environments are damaging. Previous work4'5 has demonstrated that high-pressure hydrogen (2250 psi or greater) is an effective embrittling medium, as measured by such criteria as reduction in area, notch tensile strength, and time to failure. Moreover, the embrittlement was eliminated by the addition of small quantities of air or oxygen to the high-pressure hydrogen, but it was not influenced by additions of nitrogen or argon.4 In the present study attention is focused upon gas environments at atmospheric pressure, in particular hydrogen and oxygen. The influence of these constituents upon the initiation and growth of a crack from a pre-existing cracklike flaw in a high-strength steel was determined directly by the electric-potential method of monitoring crack growth. MATERIALS AND PROCEDURE The H-11 steel was supplied by the U.S. Naval Research Laboratory as 3 by 12 by 0.065 in. sheet specimens with 1-in. transverse center slots. The slot tips were finished by Elox machining to a radius of 0.001 in. or less. The yield strength was 230,000 psi; chemical composition and heat-treatment schedule are given in Table I. The experimental apparatus, precracking procedure, and incremental loading sequence have been described previously.3 In the only significant change, precracking was sometimes carried out by a hydrogen embrittlement and baking technique. All experiments were conducted at room temperature; the hydrogen gas environment was purified by a commercial palladium purifier. Crack initiation and propagation were followed by the electric-potential method,'-3 using a calibration that has been recently dicussed. Stress-field intensities at the crack tip were computed by the conventional Irwin frmula; the plasticity correction was negligible and therefore not included. EXPERIMENTAL RESULTS A striking brittleness associated with molecular hydrogen at atmospheric pressure is demonstrated by the data in Table I1 and Fig. 1, which indicate that subcritical cracks in hydrogen initiate at lower stress-field intensities and propagate more rapidly than in fully humid argon. Ki and Kf are the crack-tip stress-field intensities at initiation and termination of subcritical crack growth, respectively. Termination, of course, corresponds to fracture. In both hydrogen and humid argon Ki is less than Kf

Jan 1, 1967

By Nicholas J. Grant, A. W. Mullendore

Measurements of grain boundary sliding were made on polycrystal and bicrystal tensile creep specimens of Al-2 pct Mg at 500oand 700oF. Grain and pain boundary orientation factors were studied with respect to their effect on the magnitude and direction of grain boundary sliding. It was concluded that a large part of the observed sliding may be caused by the operation of slip crossing the grain boundaries. Supporting evidence for this model from other investigations is also given. GRAIN boundary sliding in metals during elevated temperature deformation has frequently been thought of as an independent mechanism with its own characteristic stress, temperature, and structure dependence. Further, it is common to regard the grain boundary as the weak link during creep deformation since: 1) the strength of apolycrystallinemetal, as meas-sured by creep rate or rupture life, decreases at\a more rapid rate when sliding comes into action, and 2) grain boundary sliding, as revealed by "boundary darkening" and fold formation is often the first visible deformation. On the other hand, more quantitative observations, in both polycrystals and bicrystals, have shown boundary deformation to be closely related to the over-all deformation of the specimen. The curve of grain boundary contribution to elongation vs time takes a shape similar to that of the total creep curve,',' and the apparent activation energy for sliding appears in most cases to have the same value as that for total creep.3 In order to reconcile these observations, one is left with these possibilities: 1) The grain boundary and grain deformation rates are both controlled by the same rate limiting processes. 2) The rate of sliding is limited by accommodation deformation in the grains. 3) Sliding is the consequence of grain deformation. 4) Grain deformation is dependent on prior grain boundary deformation. Alternatives 2) and 3) would view grain boundary sliding as occurring in series with another deformation process which could be rate controlling. McLean prefers item 3) as the sliding basis,4 where subgrain rotation results from dislocation accumulation in the substructure at the grain boundary. Crussard and Friedel's5 treatment of grain boundary migration considers that dislocations are forced into the grain boundary and are dissociated into dislocations with Burgers' vectors nearly parallel to the grain boundary. The movement of these partial grain boundary dislocations then produces the sliding. The results of this investigation have indicated alternative 3) to be the most appropriate and it is this aspect of grain boundary sliding which will be analyzed. EXPERIMENTAL PROCEDURE Three types of tensile creep tests were employed in this study: (I) A constant load test of one very coarsegrained polycrystalline specimen at 500° F, 3600 psi, 1 pct per/hr strain rate to examine the grain and grain boundary orientation factors in grain boundary sliding. (II) Constant strain rate tests of polycrystalline specimens at 510o and 715o F, 2 pct per/hr strain rate to determine the grain boundary contribution to elongation at very low total strains. (m) Constant strain rate tests of bicrystals of various grain and grain boundary orientations at 500°F, 2 pct per/hr strain rate to obtain further information on the orientation effects in grain boundary sliding. The material used in the tests was a high-purity Al-1'.92 mg alloy, kindly furnished by Alcoa. Its composition is given in Table I. The alloy is a solid solution at the test temperatures. The coarse grained polycrystalline specimen for test (I) was prepared by recrystallizingthe machined specimen, straining it about 1pct intension at room temperature and annealing at 900°F for 8hr. The constant strain rate specimens (11), with an 178 in. sq. by 1/2 in. long gage section, were cut from 1/8 in. thick sheet of cold rolled and annealed (8 hr at 1000oF) material. The latter specimens were supported in a special jig during the milling operations to avoid any bending, and the gage section was subsequently heavily electropolished to remove the cold-worked surface layer. The bicrystals (ID) were machined in the same

Jan 1, 1963

By Joseph E. Worthington

The present-day Northumberland gold mine is one of the deposits generally characterized as a Carlin-type occurrence. It lies at the crest of the Toquima Range in Nye County near the center of Nevada. Gold mineralization occurs in two modes, in argillaceous and in silicified limestones, and is generally very fine-grained or micron gold. The Northumberland district has had a history that is typical of many western gold districts: minor production prior to World War II and intermittent exploration thereafter until a combination of geological insight, improved economics, and the advent of heap leach technology created the Northumberland gold mine. Nye County, Nevada, was sparsely populated and little explored in the early years of the settlement of the west; the Northumberland district was not established until 1866. Initial interest was in silver and the district operated as a very small producer for the next seventy years. The disseminated gold occurrences in silicified limestones were recognized and Northumberland Mining Co. was organized to develop the property in the late 1930s. Northumberland Mining Co. actually conducted drilling operations (over 200 drill holes) and mined from small open pits in the silicified limestones. They ultimately produced almost 936 kg (33,000 oz) gold before being shut down by War Production Board Order L-208 in 1942. After World War II gold mining activities were essentially nil for over a decade due to the poor economics of gold production. The property was, however, a known gold producer and attracted recurrent exploration attention. About 45 holes were drilled under the direction of Peter Joralemon for private interests between 1959 and 1963. Next Kerr McGee drilled about 25 holes during 1963 and 1964. Some- what later, in 1968, Homestake drilled 20 holes. The property was then acquired by Idaho Mining Co. which drilled about 30 more holes between 1972 and 1974. By this time the Northumberland mine was becoming somewhat shopworn with over 300 holes drilled. Interest in gold prospects was increasing substantially in Nevada, how- ever, due to rising gold prices in late 1974, and several companies were interested in continuing exploration at Northumberland. In 1975 Cyprus Mines Corp. was successful in obtaining a joint venture arrangement with Idaho Mining Co. for further exploration and development of the property. The overall Cyprus exploration program was under the direction of James G. Hansen, Vice President Exploration. The geologist recommending acquisition of Northumberland was Peter E. Chapman who reported to Joseph E. Worthington, Manager of U.S. Exploration for Cyprus. The basis for selection of the Northumberland mine as an exploration target for Cyprus by Chapman was essentially prior knowledge of regional and 16cal geology and of the mine. Exploration for the next few years was directed by Chapman under the supervision of Worthington. During 1975 and 1976 rotary and check core drilling were conducted that indicated that a substantial Carlin-type or disseminated, low-grade gold deposit occurred in two separate bodies. Drilling was based on geologic mapping and rock chip geochemical sampling. Both ore zones were reflected at the surface as gold and arsenic anomalies in rock chips. Heap leach tests attempted in 1977 were aborted by a flash flood, but were completed in 1978. Engineering studies occupied the next couple of years until the property achieved production in the fall of 1981. It is now producing by open-pit mining with gold recovery by heap leaching and cyanide extraction at a rated capacity of approximately 2722 t/d (3000 stpd) ore. Metal recovery has been projected (probably conservatively) at 5 10 kg/a (18,000 oz per year) gold and 1.6 Mg/a (59,000 oz per year) silver. Reserves are reported to be adequate for ten to fifteen years of production. REFERENCES Anon., 1981, "Gold in Nevada," Span Magazine, Vol. 21, No. 3, Standard Oil Co., pp. 6-9. Koschman, A.H. and Bergendahl, M.H., 1968, "Principal Gold- producing Districts of the United States, Professional Paper 610, US Geological Survey, p. 193. Kral, V.E., 195 1, "Minerals Resources of Nye County, Nevada, Bulletin, Vol. 45, No. 3, Geology and Mining Series 50, Nevada University.

Jan 1, 1985

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

By P. E. Busby, C. Wells, M. E. Warga

Fundamental data on the rate of diffusion of boron in austenite and solubility of boron in the a and y phases of iron and steel have been obtained from deboronizing experiments and provide partial explanations for some of the phenomena observed in boron steels. The rate of diffusion of boron is about the same as carbon in austenite. The solubility of boron in austenite at normal heat-treating temperatures is less than 0.001 pct. A partial tentative Fe-B phase diagram in the important low boron concentration ranges and an equation representing the diffusion of boron in austenite are presented. A LTHOUGH a search of the literature revealed ALTHOUGHthat boron diffusion had not been studied quantitatively and systematically prior to 1948, a few qualitative observations which were made by following the diffusion of boron into iron packed in ferro-boron1-3 suggest that boron obeys normal diffusion laws and that the rate of diffusion increases with increasing temperature. The claim of Cornelius and Bollenrath1 that boron does not appear to influence the rate of carbon diffusion has recently been substantiated by Wells, Batz, and Mehl.4 Calculations based on data from the paper by Campbell and Fayv indicated that the diffusion coefficient (D) for boron in iron at 900°C is approximately 3x10 sq cm per sec; a value of 2x10-7 sq cm per sec at 1038°C has been reported by Digges et al in connection with decarburizing experiments on a commercial boron steel containing 0.43 pct C. During the period 1948 to 1950 several diffusivity constant (D) values for the diffusion of boron in the y phase of iron and steel and a number of solubility values for boron in both a and y phases were reported. It was concluded tentatively as a result of Metals Research Laboratory studies that D values for boron in y and a phases are about the same as for carbon in the comparable phasesa and that carbon up to 0.4 pct did not affect the rate of diffusion of boron in y iron above 1000°C within the limits of experimental error. Whether saturation of the y or a phases with carbon would significantly affect rates of diffusion of boron through them was then and still remains in doubt. The best estimate of Q (activation energy) was reported to be about 25,000 cal, somewhat lower than that for carbon in y iron. The solubility of boron in y iron at 1000°C was thought to be higher than 0.004 pct B but not as high as a more recent analysis of available data shows it to be. The solubility of boron in a iron at 700°C was reported to be 0.0004 pct B, but it would not have surprised the authors if the true solubility value is actually lower than this. Breaks in diffusion curves which were not understood when first obtained prior to 1950 have now been recognized as indicating solubility limits, and these are included in the present paper. Experimental Procedure Two methods were employed in an effort to determine diffusion coefficients (D) for boron in austenite. Early experiments involved the use of welded couples prepared in accordance with the procedure of Wells and Mehl,&apos; but when the results of these experiments proved to be unsatisfactory for calculating D values, studies were continued by means of deboronizing experiments. In both cases, boron analyses following the diffusion anneal were carried out spectrographically and all D values were computed using the Grube solution of Fick&apos;s law. The precision of the spectrographic method used proved to be about equal to that reported by Corliss and Scribner" —average deviation from the mean about 5 pct of the amount present when the boron content is 0.003 pct. Concentration-penetration curves obtained from spectrographic analyses of welded couples generally indicated that practically no boron was transported across the weld interface during the diffusion anneal. Furthermore the concentration-penetration

Jan 1, 1954

By E. S. Machlin

The wzodel of Blandin and Diplunt;, generalized to include a phase factor, is applied to the carbon-carbon interaction in iron. Darken&apos;s "energetic" model is generalized to include not only first neighbor interactions but further neighbor interactions as well. On the bases of these generalized models relations are derived for the activity of carbon in both austenite and ferrite in terms of the carbon-carbon Pair interaction energies. A single function then yields the pair interaction energies consistent with the experimental activities of carbon in both ferrite and austenite. Thus, a simple explanation is given for the observation that the nearest-neighbor interaction between carbon is repulsive in austenite and attractive in ferrite. Certain consequences of this approach are explored. OnE object of the present paper is to attempt to take into account the consequences of electrostatic contributions to the carbon-carbon pair interaction energy for carbon as a solute in iron. Friedel&apos; has shown that oscillations in electrostatic potential are to be expected about a solute atom in a metallic solution. Blandin and 6lant6&apos; have shown that such oscillations yield an interaction energy between pairs of solute atoms that obeys the relation: W{ = A cos(2ftFri + 4>)/(kFri)3 [l] where kF = Fermi wave vector, ri = distance between solute atoms comprising the pair7 <p = phase factor dependent only on electronic nature of solute and solvent, A = coefficient dependent only on electronic nature of solute and solvent. Machlin3 found that Eq. [I] accurately described the pair interaction energy derived from short-range order measurements based on field ion microscope observations of dilute alloys of platinum. He also found that the value of the phase factor $ derived from residual resistivity measurements agreed well with that obtained from the analysis of the short-range order data. Harrison and paskin4 were able to predict the long-range ordering energy of 0 brass using Relation [I] and residual resistivity values to predict the value of the phase factor $. Machlin5 has repeated their analysis and applied it to the prediction of the long-range ordering energy in AgZn and AgCd with excellent agreement between prediction and experiment. Both A and $ are independent of the crystal structure. The Fermi wave vector depends uniquely upon the conduction electron concentration per unit volume in the spherical approximation of the Fermi surface. Thus, Eq. [I] is expected to apply to both fer- rite and austenite with only one set of values of A and $. Mossbauer studies6 yield the result that iron has one 4s electron. We shall make an assumption found to hold previously for platinum3&apos;7 and nikel, which is that only the s electrons are involved in shielding the perturbing potential of carbon. With this assumption, kF = 1.35 A-l. Although A and $ may be obtained from certain mdels&apos;&apos;&apos; we shall take A and $ to be empirical constants in the spirit of Kohn and osko.&apos; Thus, Eq. [I] involves two adjustible parameters. Consequently, two independent relations in A and $I are required in order to evaluate them for carbon as a solute in iron. We may use a recent analysis of Aaronson, Domain, and poundg who showed that Darken&apos;s energetic model,1° as well as others, can be used to describe the activity-temperature data for carbon in iron in both the aus-tenitic and ferritic phases. Darken&apos;s model takes into account only first neighbor pair interactions. For our needs, all neighbor pairs need to be taken into account. It is convenient to generalize Darken&apos;s model. The result for the partition function for austenite is: over the temperature range 800" to 1200°C and where the uncertainty corresponds to one standard deviation. Eq. [4] effectively yields only one relation. Another relation is required to obtain unique values for A and $. One property of Eq. [4] is that it is independent of crystal structure. Hence, data for a iron can be used to obtain another relation. To arrive at this relation we must generalize Eqs. [2] and [3] so that they may be applied to the bcc a iron. The result is that:

Jan 1, 1969

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

By D. D. Smith, D. P. Squier, E. L. Dougherty

A system of differential equations describing the temperature behavior of fluid injected at constant surface temperature in a well is derived and .solved analytically. A formula for the fluid temperature at any time and depth is given, as well us a special formula valid for very large times. These formulas are used to calculate temperatures for several typical cases. The results indicate that, initially, the temperature of the water entering the formation is considerably lower than the injection temperature. This condition lasts for only a short period— less than three days for most cases of practical interest. Following this highly transient period, during which the temperature of the fluid entering the formation builds up to about 50 to 75 per cent of the injection temperature. the system enters a quasi-steady state in which the temperature changes are very slow. After severl years, the bottom-hole temperature will still be 50" to 100°F lower than the injection temperature, hilt the heat losses may he tolerable. INTRODUCTION Predicting the behavior of a hot-water flood requires that the temperature of the water entering the injection interval be estimated. This report describes the development and solution of a system of equations which describes the temperature behavior of the injected water in the wellbore with certain simplifying assumptions. The only previous means known to the authors for describing such a process is that of Moss and White.&apos; Their results appear to be close to those obtained by our method in the practical cases which were compared; this agreement is largely due to the fact that in our method temperature soon approaches a quasi-steady state, as was assumed in their method throughout. However, our model covers all times, is continuous (whereas the Moss-White model depends on breaking the depth into discrete intervals) and. we feel. more closely describes the physical problem. FORMULATION OF THE PROBLEM PHYSICAL SYSTEM AND ASSUMPTIONS The injection procedure consists of pumping water at a fixed surface temperature T., down an infinitely long cylindrical well or tubing of inner radius Any material exterior to the water column such as mud, casing, or cement is regarded as part of the formation. The general behavior of the system may be described qualitatively as follows. When the hot water is first introduced into the system, the temperature difference between the formation and the water is large, resulting in a high rate of heat transfer. As a result, the temperature adjacent to the wellbore rises very quickly. Because the segment of the formation adjacent to the wellbore largely controls the heat transfer rate, the heat transfer rate will become relatively constant when this portion has reached a temperature close to that of the water opposite it. The temperature of the water and formation then increase very slowly with time. The length of the initial highly transient period and the temperature of the water at its conclusion will be functions of depth, injection rate, injection-string radius, surface injection temperature and the physical properties associated with the water-formation system. The following additional assumptions were made. 1. There is no heat transfer by radiation in the system. 2. There is no heat transfer by conduction in the vertical direction in either the injection stream or the formation. 3. The linear volumetric and mass flow rate of the water is constant throughout the injection stream. 4. No horizontal temperature gradient exists in the injection stream. 5. The product of density and heat capacity is constant for both the water and the formation, and the formation thermal conductivity is constant. 6. Initially, both the water in the wellbore and the reservoir are at a temperature given by the (constant) ambient surface temperature plus the product of depth and geothermal gradient (assumed constant). At large distances for the wellbore (r m), the formation will remain at this temperature. 7. The water temperature and the formation temperature at r — r,, are equal for all depths D. DERIVATION OF EQUATIONS The differential equation satisfied by the fluid temperature T,(D, t), which is obtained by writing a heat balance on a cylindrical differential of volume dV of the injection string between the depths D and D i dD, is

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Data obtained under controlled test conditions using a microbit drilling machine showed that oil emulsified in water muds may either increase or decrease the drilling rate, depending upon drilling conditions. A low-viscosity oil such as diesel fuel can give drilling rates in limestone almost equal to that of water. Data obtained for water emulsified in oil muds showed little decrease in the drilling rate in water-saturated cores as the water percentage of the mud was increased above the 5- to 10-percent range. Changes in drilling rate were found to be dependent upon the oil or water concentration of the mud and upon the type of formation drilled. Changes in static filtration on paper (API filtrate) did not correlate with filtration while the mud was circulated across rock. INTRODUCTION Oil additions to water muds have been reported to increase drilling rates, provide hole stability and improve filtration control. Eckel&apos; showed that water-base emulsion muds used in the West Texas area increased drilling rate with increasing oil concentration up to 15 percent oil by volume, but drilling rate decreased at a concentration of 20 percent by volume. Based on laboratory tests using water muds to drill shale, Cunningham and Goins&apos; reported that drilling rates increased and tendency for the bit to ballup decreased with the addition of oil. Percentage increase in drilling rate varied with the particular formation. They showed oil additions to improve drilling rates ap proximately 75 percent in Vicksburg shale and as much as 150 percent in Miocene shale. Each investigation showed an optimum oil content for the particular formation. Most data that indicated improved filtration control due to oil additions were based on static API Eltrates through paper rather than dynamic filtration through permeable rocks. Some types of dynamic test give a better representation of filtration down-hole while drilling and might be more likely to show some correlation with drilling rate. Static filtration would be important, of course, in relation to hole stability and formation damage. This laboratory&apos;s drilling tests, conducted on water-raturated Berea sandstone, indicated that improvements in drilling rate were not evident with increasing oil concentration in water-base muds. Investigation also showed similarity between oil-emulsion (water-in-oil) muds and water-emulsion (oil-in-water) muds while drilling these formations. In Lueders limestone high concentration of water-in-oil muds and high concentration of oil-in-water muds provided the same relative drilling rates. In Berea sandstone there was a large reduction in relative drilling rate with both the oil and water muds that contained low percentages of emulsified fluid. Dynamic filtration rates of water muds on rock did not always decrease with increasing oil percentages even though the static API filtration rates on paper did decrease. Data observed in laboratory drilling of limestone and sandstone indicate that improvements in field drilling operations when water- or oil-emulsion muds are wed may not be the result of increased drilling rates but of improved hole conditions. In some cases, actual drilling rates might be slower but improved hole conditions will result in less total time on the hole. DEFINITIONS Mud pressure—Pressure of drilling fluid as measured after leaving the drilling chamber. This is considered as the approximate mud pressure just past the bit and at the face of the formation. Terrastatic pressure—Pressure representing weight of overburden. Formation pressure—Pressure of formation fluid as measured at outlet of drilling chamber. This is considered as approximate pressure of fluid in the pores of the formation. Differential pressure—Difference between the mud pressure and formation pressure. Relative drilling rate, percent—Drilling rate with experimental fluid divided by drilling rate with water times 100 equals percent. LABORATORY EQUiPMENT AND TESTING PROCEDURES The drilling equipment has been described in previous publications The microbit drill is a closed system (capacity, approximately 7 gal) that can be pressurized to 15.000 psi and heated to 500F. Main components are a drilling chamber, filter-heater, rotary-drive and variable-speed cir-

By T. L. Joseph, G. Bitsianes

THE layered structure of partially reduced iron ore was described in a previous paper.&apos; Reduction by hydrogen was found to take place at well-defined interfaces between layers of the solid phases. In the present investigation, a detailed study was made of the wiistite phase that had formed during the partial reduction of a cylindrical compact of chemically pure hematite. An unusually wide band of wiistite permitted a rather detailed study of this phase. The specimen was made from Baker&apos;s C.P. hematite in the form of a cylinder 1.5 cm in diameter and 1.8 cm long. A dense ore structure with about 6 pct porosity was attained by heating the specimen in air at 1100°C for 3 hr. To confine reduction to the top surface, a ceramic coating was applied to the bottom and sides of the cylindrical compact. The specimen was then partially reduced in hydrogen at 850°C and subjected to a coordinated sequence of macro-, micro-, and X-ray examinations. A section of the partially reduced cylinder is shown in the macrograph, Fig. 1. Four layers consisting of metallic iron, wustite, magnetite, and unreduced hematite are clearly shown. The effort to force reduction to proceed downward in topochemi-cal fashion was only partly successful, as some reduction occurred along one side and bottom of the cylinder. A rather wide layer of dark wustite phase had formed, however, and permitted sampling for X-ray studies as indicated. To supplement previous work and to study the wustite layer in more detail, ten separate layers were removed for X-ray examination. Broad and diffuse patterns were obtained with the as-filed powders, especially with those of iron and wiistite, and the condition indicated a cold-working and variable composition effect within the respective layers. This condition was corrected by annealing the entire series of powders at an appropriate temperature. For the annealing treatment, the ten powder samples were wrapped in silver foil, sealed under vacuum in small quartz tubes, and heated at 750°C for 16 hr. The specimens were then drastically quenched in cold water to preserve the annealed condition. These annealed specimens were X-rayed in turn and the compiled patterns are shown in Fig. 2. The standard patterns for iron and its oxides have been interjected at appropriate positions for purposes of comparison and phase identification. All of the patterns obtained were clearcut and concise so that positive identifications could be made for all of the phases. The outermost layers A, B, and C were composed almost entirely of iron with a small amount of wiistite being detectable at the X-ray limit of phase detection. Layer D from the iron-wustite interface showed both of these phases. The next four layers E, F, G, and H were all in the dark phase band which had been tentatively identified as wustite by the macroexamination, Fig. 1. The diffraction data with their single-phase patterns of wiistite for these layers checked the visual evidence. Continuing the X-ray analyses after layer H, the macrograph (Fig. 1) shows that layer I came largely from the magnetite zone but included some fringes of the wiistite-magnetite interface. The diffraction pattern for the sample confirmed this observation. Layer J came from the unreduced core of the specimen and its diffraction pattern indicated a preponderance of hematite phase. The reduction behavior of synthetic compacts has thus been found to be similar to natural dense iron ore. The previous results were supplemented with measurements of the diffraction films and calculations of the respective unit parameters. These X-ray data are summarized in Table I and offer some interesting correlations as to the compositions of the various phases undergoing reduction. The iron layers that were analyzed gave lattice parameters close to that of pure iron at 2.8664A. Evidently this iron was present in layers A through D as a pure phase with little or no oxygen dissolved in its lattice. With the wiistite layers an entirely different situation prevailed in that there was a definite and

Jan 1, 1955