Search Documents

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No' 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements' From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

Samuel T. Wellman, Cleveland pioneer steel man, who was often referred to as the "father of the open-hearth process of the United States," died suddenly on July 11, 1919, of heart disease, at Stratton, Me. For more than half a century, he was closely identified with the improvement of equipment used in the making of steel and contributed a number of inventions that virtually revolutionized the industry. Mr. Wellman was born Feb. 5, 1847, at Wareham, Mass., his father at the time being superintendent of the Nashua Iron Co., Nashua, N. H. After attending public school and a year at Norwich University, he served in the Civil War as a corporal of the first New Hampshire Heavy Artillery. He went to Pittsburgh in 1867 and assisted in starting the first crucible steel melting furnace built in America at the works of Anderson, Cook & Co. It melted a ton of steel with an average of 1000 Ib. of nut coal, which cost less than $1, while the melting of a ton of steel in crucibles in the old fashioned coke furnace took three tons of the very best coke, costing from $2 to $3 per ton. This furnace was a great success and in a very few years had driven the coke furnace out of use. From Anderson, Cook & Co., Mr. Wellman went to the Singer, Nimick & Co. works, Pittsburgh, where he built two crucible steel melting furnaces of the same type. After that he spent some time in the office of the Siemens agents in Boston and also at steel works in different parts of the country, starting crucible steel furnaces. He then went to the Bay State Iron Works in South Boston, Mass., where he built the first open-hearth furnace that was a commercial success in the United States. It made steel of a much better quality than had previously been made in this country. The principal use to which it was put in those days was the manufacture of locomotive fire-boxes. From South Boston, he went hack to the old works in New Hampshire where his father was still superintendent, and built for it an open-hearth furnace, a plate mill, and a bar mill. In 1873, Mr. Wellman went to Cleveland to design and build the plant of the Otis Steel Co. He remained with this company for 16 years as engineer and superintendent. During this time he developed the open-hearth charging machine and introduced the electromagnet for handling pig iron and scrap steel. The first charging machine was operated by hydraulic power, and although it was not entirely satisfactory it performed the work fairly well and encouraged its inventor to build another one, which was driven by electric motors. This proved

Jan 1, 1920

By D. M. Davidson

The drill sampling and evaluation of the Piney River ilmenite property was carried out during the early part of 1944 by E. J. Longyear Co., using the company's standard core-drill outfits to complete 44 holes to an average depth of IIO ft., from which were collected 1100 samples. The Piney River ilmenite-apatite lode is 25 miles north of Lynchburg, in Nelson and Amherst Counties, Virginia (Fig. I). Its elevation is about 900 ft. above sea level and it lies in the old pre-Cambrian complex of crystalline rocks that make up the Piedmont physiographic province lying east of the Blue Ridge Mountains. The terrain is gently rolling and well watered and is drained by the Piney and Tye Rivers, which are tributary to the James. Geology The Piney River ore body comprises the upper, weathered part of a tabular basic rock, which occurs in a large area of granite-gneiss. The section containing profitable ore is about 3000 ft. long. It is separated naturally by thinning, into northeastern and southwestern segments with widths of 300 and 100 ft. respectively. The dip averages 4.5° southeast but steepens locally (Figs. 2 and 3). The unaltered rock is an even, granular mixture of feldspar, ilmenite, and apatite, to which Watson1 gave the name Nelson-ite. The decomposed ore body, which is now being exploited by open cut, is a yellowish clay material in which black ilmenite and glassy apatite are the only conspicuous minerals. An economically important structural feature of the deposit is a banding of minerals coinciding with the dip and strike of the dike. This is more pronounced in the footwall of the northeastern part of the intrusive, where there is also a higher than average concentration of ilmenite. According to Watson,' the TiO2 content of the Nelsonites of this region ranges from 10 to 42 per cent, while P205 varies from 4 to 15 per cent. It is inexpedient at present to disclose exact metal content of the Piney River ore body; suffice it to say that the average tenor lies well within the extremes noted by Watson. Sampling Methods and Procedure During a preliminary inspection of the ore body, Longyear engineers surmised that because of its soft, clayey character, drill sampling would yield little core, therefore they made all possible preparations to procure accurate samples of the drill cuttings, or sludge. The first requisite in obtaining representative drill cuttings is to secure their full recovery. Only under certain conditions, and by employing a most careful and rigid sampling technique, is this pos sible. There must be no loss of the water circulating in the hole, and the velocity

Jan 1, 1949

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiCl-KCl mixtures, as first proposed by Guntz.2 The details of the industrial process have not been made public but Osborg8 stated that an efficiency of more than go pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of too kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, Si02, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units, such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, especially with respect to the iron and calcium content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1947

By A. Kenneth Schellinger, O. Cutler Shepard

INTRODUCTION OVERGRINDING, or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncontrolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about 90 pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, overgrinding is detrimental to the flotation process. Overground slime coats larger particles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 Conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The remedy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. DEVELOPMENT OF APPARATUS AND EXPERIMENTAL METHOD Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7 ½ in. in diameter and 8 in. deep. A cast-iron disk was mounted on the end of a vertical shaft so that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffeemill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, weighed charges of ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned on so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1947

By R. S. Busk

TWO groups of binary alloys were prepared. The first group consisted of those elements relatively soluble in magnesium: Li, Al, Zn, Ga, Ag, Cd, In, Sn, Hg, T1, Pb, and Bi. These are predominately Group B elements. The second group consisted of most of the remaining metallic elements, all of which are relatively insoluble in magnesium: As, Au, Ba, Ca, Ce, Cu, Ir, La, Mn, Ni, Pd, Pt, Rh, Sb, Si, Te, Ti, W, and Zr. These are all Group A, transition, or rare earth elements. Alloys of the first group were prepared by melting sublimed magnesium and elements as pure as obtainable in a graphite crucible, using a standard flux1 for protection. The melts were poured into a small graphite mold to produce 3xY4 in. diam slugs. Spectroscopic analyses were made of each slug. In all cases, the total impurity content was less than 0.05 pct. The slugs were then heat treated 5°C below the eutectic temperature until complete solution, as judged metallographically, was obtained. Filings from the center of the slugs were compacted at room temperature into 1/2 in. long x 1/4 in. diam cylinders, sealed in pyrex under 1/2 atm of purified argon, annealed at the heat-treating temperature for 1 hr, and quenched in water. After the X-ray diffraction patterns were made, each compact was analyzed chemically for the solute. It was found that the Mg-Li alloys reacted during filing to reduce the Li in solid solution. For this series of alloys, the slug was cold worked, annealed in purified argon, the surface dissolved in dilute HC1 to a depth of about 0.005 in., and the X-ray exposure made on the fresh surface. This procedure resulted in sharp, continuous lines and in true values for the lattice parameters. The alloys in the second group were prepared in the same way except that about 1 wt pct of each solute was added. Since the solubility limit was exceeded, not all the solute dissolved. These alloys were analyzed spectroscopically only to confirm the presence of the solute. The diffraction patterns were of the back-reflec-tion type using the characteristic copper radiation* and a flat cassette. Both the film and the specimen were rotated. The specimen temperature was maintained at 25" ± 1°C. The films had sharp lines; their diameters were measured directly to 0.01 cm. The parameters were calculated from the line diameters using a modified version of Cohen's extrapolation method.2 his method effectively eliminates systematic errors such as film shrinkage, inaccurate alignment, and non-precise film-to-speci-men distance. The random errors were minimized

Jan 1, 1951

By J. R. Cahoon, W. V. Youdelis

FOR the diffusion of copper in silver-rich alloys, there have been only two previous investigations, that of Seith and Peretti in 1936, and that of Sawatzky and Jaumot2 in 1957. Seith and Peretti obtained a value of 24.8 keal per g-atom for the activation energy of diffusion whereas Sawatzky and Jaumot obtained a value of 46.1 keal per g-atom. Admittedly, Seith and Peretti used relatively high concentrations of 2 at. pet Cu and polycrystalline diffusion couples, while Sawatzky and Jaumot investigated tracer diffusion in single crystals of silver. The difference in the results, however, seems too large to attribute solely to solute concentration, as a change of over 20 keal per g-atom in the activation energy suggests a change in the mechanism of diffusion. Therefore, in the present investigation the diffusion coefficient for copper in polycrystalline Ag-2 at, pet Cu alloy is re-established using conventional sandwich-type diffusion couples and electron-probe microanalyses, and the results are compared with those of the previous studies. The diffusion couples were prepared from high-purity silver (99.999 pet) and high-purity copper (99.999 pet). The silver disks, 1/4 in. long and 4 in. in diam, were machined from an ingot which had been solidified in a dynamic vacuum of 10-3 mm of Hg to eliminate oxygen absorption which otherwise would result in copper oxide precipitation in the weld zone. The alloy disks of similar dimensions were machined from an alloy ingot (nominal composition 2 at. pet Cu) which had been unidirectionally solidified to obtain a predictable solute concentration,3 and homogenized for 1 week at 800°C. Sandwich diffusion couples were made by pressure welding an alloy disk between two silver disks in an induction heating coil. The couples were diffusion-annealed at temperatures of 800°, 756°, 699°, and 630°C in tube furnaces in which the temperature was controlled to better than ± l°C. The diffusion couples were examined metallographically for weld defects, and couples showing even minute defects at the weld interfaces were rejected. Concentration penetration curves were established using an A.R.L. Microprobe analyzer. CuKO radiation was counted and converted to concentration using 0.5 and 1.0 wt pet Cu chemically analyzed standards. Initially, four continuous profiles were obtained, and averaged to obtain the final diffusion curve. The initial analysis was performed commercially and the welds were not located with respect to the profile. Therefore, the results were rechecked by the authors using the Mellon Institute A.R.L. probe. In the latter case, concentrations were obtained at 10-µ steps for four different traverses, and then averaged to obtain

Jan 1, 1968

By D. M. Davidson

The drill sampling and evaluation of the Piney River ilmenite property was carried out during the early part of 1944 by E. J. Longyear Co., using the company's standard core-drill outfits to complete 44 holes to an average depth of IIO ft., from which were collected 1100 samples. The Piney River ilmenite-apatite lode is 25 miles north of Lynchburg, in Nelson and Amherst Counties, Virginia (Fig. I). Its elevation is about 900 ft. above sea level and it lies in the old pre-Cambrian complex of crystalline rocks that make up the Piedmont physiographic province lying east of the Blue Ridge Mountains. The terrain is gently rolling and well watered and is drained by the Piney and Tye Rivers, which are tributary to the James. Geology The Piney River ore body comprises the upper, weathered part of a tabular basic rock, which occurs in a large area of granite-gneiss. The section containing profitable ore is about 3000 ft. long. It is separated naturally by thinning, into northeastern and southwestern segments with widths of 300 and 100 ft. respectively. The dip averages 4.5° southeast but steepens locally (Figs. 2 and 3). The unaltered rock is an even, granular mixture of feldspar, ilmenite, and apatite, to which Watson1 gave the name Nelson-ite. The decomposed ore body, which is now being exploited by open cut, is a yellowish clay material in which black ilmenite and glassy apatite are the only conspicuous minerals. An economically important structural feature of the deposit is a banding of minerals coinciding with the dip and strike of the dike. This is more pronounced in the footwall of the northeastern part of the intrusive, where there is also a higher than average concentration of ilmenite. According to Watson,' the TiO2 content of the Nelsonites of this region ranges from 10 to 42 per cent, while P205 varies from 4 to 15 per cent. It is inexpedient at present to disclose exact metal content of the Piney River ore body; suffice it to say that the average tenor lies well within the extremes noted by Watson. Sampling Methods and Procedure During a preliminary inspection of the ore body, Longyear engineers surmised that because of its soft, clayey character, drill sampling would yield little core, therefore they made all possible preparations to procure accurate samples of the drill cuttings, or sludge. The first requisite in obtaining representative drill cuttings is to secure their full recovery. Only under certain conditions, and by employing a most careful and rigid sampling technique, is this pos sible. There must be no loss of the water circulating in the hole, and the velocity

Jan 1, 1949

By A. Kenneth Schellinger, O. Cutler Shepard

Overgrinding, Or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncon rolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about go pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, over-grinding is detrimental to the flotation process. Overground slime coats larger partitles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The rem- edy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. Development oF Apparatus and Experimental Method Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7½ in. in diameter and 8 in- deep. A cast-iron disk Was mounted on the end of a vertical shaft SO that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffee-mill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, more charges of Ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned On so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1949

By Horace W. Hindry

This paper presents the ingredients composing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. INTRODUCTION AN oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various California fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion [oil] drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of variables, and the almost unlimited possible combinations of these variables, which in turn require extensive laboratory study, there are certain irregularities and omissions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. FUNDAMENTAL DESIGN OF AN OIL-BASE MUD In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By M. S. Abrahams

Germanium has been rolled in the temperature range of 700o to 800°C. The thickness has been decreased by as much as a factor of four, from a thickness of 0.032 in. to a thickness of 0.008 in. For deformations below 60 pet, the true strain per pass is found to be a constant; from the temperature dependence of this slope, an activation energy of about 2.5 ev is obtained. This energy agrees with that for dislocation climb in germanium . For reductions greater than 60 pet, complete rings are seen in the Lave photographs, new grains are observed in the microstructure, considerable softening occurs, and the hole mobility is very low. This evidence indicates that the recrystallization of gertnanium has occurred. GERMANIUM has been deformed in many ways1 including tension, compression, torsion, and bending since Gallagher2 first described its plastic nature at elevated temperatures. All of these studies indicate that the glide plane in germanium is (111) and that the glide direction is (110). Rolled germanium specimens were used by Kolm, Warekois, and Kulin3 in their X-ray study of deformed semiconductors, but no information is given on the rolling itself. The present experiments deal with the rolling of germanium at various temperatures and for different orientations. In all previous deformation studies, the phenomenon of recrystallization (i.e., the transformation of a single crystal into a polycrystal) in germanium has not been observed4 despite relatively large deformations at elevated temperatures. The proposed reason4 for this was that sufficient energy could not be stored in the deformed germanium lattice. In contrast to the earlier studies this work will present evidence indicating that recrystallization occurs in germanium during rolling at an elevated temperature. I) EXPERIMENTAL PROCEDURE A) Test Specimens. The samples used for rolling were in the form of rectangular parallelepipeds measuring 0.3 in. long, 0.06 in. wide, and 0.035 in. high. They were cut from an undoped single-crystal ingot of p-type germanium with a resistivity of 24.4 ohm-cm, a Hall mobility of 2300 sq cm v-' sec-l, and a hole concentration of 1.1 x 1014 cm"3 at room temperature. The surfaces of the specimens were metallographically polished prior to rolling. The initial dislocation density of the samples was about 10' cm-' as determined by etching in CP4. Two different specimen orientations were used. In the first case, the direction of rolling was parallel to (251), the surfaces in contact with the rolls were of the form (1021, and the normal to the third face was parallel to (211). The corresponding di-

Jan 1, 1964

By Carl Tolman, LeRoy Scharon, Harold Powers

THIS paper presents geophysical and subsurface data observed in the vicinity of Shafts No. 1 and and 5 of the National Lead Co. lead mines at Fred-ericktown, Madison County, Missouri, see Fig. 1. The area selected is an excellent example to illustrate the close correlation between geophysical data and geological facts as revealed by drilling and mining. Such close correlations make geophysical applications appropriate to the development of known ore-bodies as well as the exploration for new orebodies. In the past, magnetic and shallow electrical resistivity observations were made over limited areas in the Fredericktown lead district by the Missouri Geological Survey, with favorable results. The first extensive magnetic and electrical resistivity surveys were started by the U. S. Bureau of Mines in May 1945 in two areas located northwest and southwest of Fredericktown, as shown in Fig. 1. The results of these surveys were reported in April 1948 at Denver, spontaneous-polarization surveys were made over the property of the St. Louis Smelting and Refining Co. at Fredericktown by Sherwin F. Kelly Geophysical Services, Inc. Aeromagnetic surveys were completed in 1948 over the Fredericktown quadrangle by the U. S. Geological Survey. Since 1945 geophysical surveys have been an important part of exploration programs in the Fred- ericktown district. Such methods, magnetic and electrical resistivity, are now serving as guides in the further development of known orebodies. On an irregular pre-Cambrian igneous erosion surface Lamotte sandstone of upper Cambrian age was deposited, partially filling the topographic basins, see Fig. 2. Above and conformable with the Lamotte sandstone lies the Bonneterre formation, a dolomite with locally interbedded thin dolomitic limestones and shales at its base. This formation also only partially filled the topographic basins. The Bonneterre was overlain by the Davis, Derby, Doe Run, and Potosi formations, which are principally dolomite. Uplift, tilt, and slight warping has allowed erosion and weathering to remove most of the sediments overlying the Bonneterre, and in many places, not far from the mine, the Lamotte sandstone is exposed. This erosion has also exposed areas of pre-Cambrian igneous rock. The Lamotte sandstone, having been deposited on an irregular pre-Cambrian surface, is extremely variable in thickness and ranges from zero where it laps the pre-Cambrian rocks to 250 ft thick in the deeper basins. In the vicinity of the mines the Bonneterre dolomite ranges from zero where it wedges out against the pre-Cambrian igneous rocks to 400 ft thick. The ore deposits occur as a bedded disseminated type1 and are chiefly composed of galena and pyrite with minor amounts of chalcopyrite and siegenite. Heavy pyrite and marcasite mineralization may be found throughout the Bonneterre formation. However, there is little or no apparent association of these iron sulphide bodies lying above the ore hori-

Jan 1, 1954

By Herman Garlichs

THE development of the extensive Southeast Missouri deposits greatly preceded that of the Iowa and Wisconsin deposits. It began about 1720 at Mine La Motte and other localities, and has continued uninterruptedly to the present time. It is estimated that this district produced about 184,000 tons of lead in the year 1916, having a value of approximately, $25,000,000. This is a new high record. The Southwest Missouri orebodies were hardly known before 1845 and were not extensively developed until 1870: Lead production in South-west Missouri for 1916 was 38,788 tons. Oklahoma produced 14,399 ,tons and Kansas 2,345 tons, making a total for Southwest Missouri, and the adjoining districts in Oklahoma and Kansas, of 55,532 tons of lead. The first metallurgists in Missouri were the Indian and the hunter. The early settler learned to procure his bullets either by melting ore in his camp fire or by throwing pieces of galena on an old stump and depending on the usual roasting and reaction method to obtain the metal. A little more refined method was to arrange two flat stones in the form of a V. Wood and galena were placed in the furnace and ignited. As heat developed, some of the metal was extracted and molded into bullets. The next step in utilizing the lead ores was the log hearth. All lead in Missouri was smelted in this crude affair before 1820. It was built on sloping ground, and consisted of a hearth of stone, surrounded on the front and two sides by a stone wall. The wall was 7 ft. high in front. The top and rear end were left open and in front an arch or opening was made, forming the eye of the furnace. In front of this a pit was dug in the ground, to receive the molten metal. Large logs were rolled in at the back and made to rest upon ledges formed inside, to raise them from the hearth and to give a draft. These logs filled the entire width of the furnace. Small split logs were then set up around the two sides and the front, and the ore was piled on until the furnace was full. Finally, the mass was covered with logs and fuel until the ore was completely surrounded. A gentle heat was started, which was raised very gradually. After 12 hr. the heat was increased and continued for 12 hr. more, 24 hr. being required, for each smelting. The furnace treated about 5,000 lb. per 24 hr. and the ore yielded about 50 per cent. of its metallic lead. A considerable quantity of the ore was not desulphurized, and fell between

Jan 7, 1917

By J. Murray Riddell, George A. Morrison

THIS paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.[+] Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Barberton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 20-40 ft. Fractured. sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), 3/8 by 4 by 4-in. angle irons; spacing of sets, 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. THE SHAFT-SINKING OPERATION The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (I) a storage pocket of 300 cu. ft. capacity with truck servicing facilities, and (2) pneumatically operated dump doors, which were actuated by the hoistman, thus caring for the dumping of the "ball-and-chain"

Jan 1, 1944

By A. G. Lyle, J. D. Runkle, G. A. Gillies

THE evaluation of data obtained by selective flotation from even a simple ore is a very difficult process, and when the ore tested is complex the process becomes extremely difficult and cumbersome. The authors, in the course of an investigation into the selective behavior of various flotation reagents on nonmetallic minerals§ were confronted with an aggravated form of this difficulty, owing to the large mass of data that had accumulated over a period of years. They finally devised a method whereby the results of the various flotation tests could be correlated and interpreted by means of graphs representing recoveries and rejections of the component minerals in the ore. This method of graphical analysis proved so useful in nonmetallic flotation that it was afterwards applied to sulphide flotation, where it yielded equally satisfactory results. Since this method of analysis leads to very definite conclusions as to the effect of changes in reagents and flotation procedure, it is felt that a wider application of the method might assist the industry by reducing the amount of test work required, and possibly increase the accuracy of the final analysis. GRAPHS In Fig. I, four curves are plotted on the same graph with cumulative percentages as ordinates and cumulative weights as abscissas. In this instance the four curves are named, respectively: the barite-recovery curve, the limestone-rejection curve, the silica-rejection curve, and the summation curve. In these tests barite was the mineral concentrated, therefore a barite concentrate was produced. Definitions Before explaining the curves in detail it might be advisable to define several new terms, such as "percentage rejection," "summation index," and "summation curve," as well as the word "test," which has been used in a special sense. A "test" will include all the operations performed upon a batch of ore from the time it is placed in the rod mill until the last product has been assayed. Thus a test may be a comparatively simple procedure producing only one concentrate and a tailing, or it may be a very complicated procedure producing five or more concentrates of a specific mineral as well as a tailing. The number of concentrates produced will depend entirely upon whether the collector was added to the pulp in the flotation cell in one lot or was added in five or more portions. Percentage Rejection.-The ability of a selective flotation collector to reject an undesired mineral is just as important as its ability to collect the desired mineral. The percentage rejection curves shown on the graphs give this factor due consideration and its value is calculated as follows: Suppose a concentrate contains 5 per cent of an undesired mineral. This indicates

Jan 1, 1942

By Jack A. Crichton, Henry J. Gruy

This paper discusses methods used in the estimation of natural gas reserves and the general conditions under which the various methods are applicable. The factors used in estimating natural gas reserves are reviewed. Errors which have been found to occur frequently are listed. Introduction The estimation of natural gas reserves has become of paramount interest because of the increasing importance of gas in the nation's economy. Gas is a most desirable fuel, a fact substantiated by the continued rise in the market demand. In addition, new uses for gas are being developed by the chemical, plastic, and associated industries, and plants are being built to make gasoline from natural gas. These are a few of the factors contributing to the importance of the nation's natural gas reserves. With the increased importance of gas there is an increase in the need for reliable estimates of the magnitude and availability of natural gas reserves. These estimates are being used currently: (I) to determine which fields contain sufficient available reserves to justify the construction of pipe-line outlets to serve particular markets; (2) to design pipe lines necessary to serve those fields adequately;] (3) to determine the location of industrial and chemical plants; (4) to finance the development of gas properties, and the construction of gas pipe lines; (5) to determine fair and adequate depletion allowances and depreciation rates; (6) to justify applications for gas pipe lines before various regulatory bodies; (7) to determine the number of wells required to exploit the reserves most economically; (8) to aid in establishing values for the purchase or sale of gas properties, and for purposes of inheritance taxes; (9) to determine equities under unitized operations; (10) to provide a basis for calculating the economics of gas-cycling operations. History or Estimation of Natural Gas Reserves The natural gas industry in the United States had its beginning during 1826 when natural gas was used for lighting the city of Fredonia, N. Y. The first natural gas pipe line was a 25-mi]le wooden line constructed from hollowed logs, connecting West Bloomfield and Rochester, N. Y. There is no record of an attempt to estimate the gas reserve at West Bloomfield but an attempt was made to determine the capacity of the well by measuring the time required to 611 a large balloon. One of the earlier publications concerning estimation of natural gas reserves is the "Manual for the Oil and Gas Industry," published by the Treasury Department, United States Internal Revenue, in i9i9. The following methods of computing "gas depletion" are listed: (I) production decline of the gas well or property; (2) decline in open-flow capacity; (3) comparison with the life history of similar wells or properties, particularly those exhausted Art

Jan 1, 1949

By Paul Hunt

UP TO June, 1923, the Park-Utah mine had shipped about 94,000 tons of a direct-smelting ore of a gross value of $4,200,000, or about $45. a ton. These values were in gold and silver only, although the ore carried small amounts of lead, copper and zinc. Freight, treatment and deductions had averaged $15.40 a ton. At the expiration of the Pittman Silver Act there was in sight about 30,000 tons of a similar ore with a gross value of about $15 a ton in gold and silver, and a large body of partly developed lead-zinc ore of a gross value of about $20 a ton, 40 per cent. of which was represented by the lead-zinc content and the balance by the silver and gold. Mine costs had been high during the life of the Pittman Act, but as a large part of the profits had gone into equipment of the mine and the orebodies were large and had good walls, we knew that mine costs could be greatly reduced. We were therefore faced by the necessity of getting lower freight and smelter rates or of concentrating the ore. We did obtain better freight rates on lower grade ore, and a favorable smelting rate on the small tonnage of siliceous silver-gold ore, but this smelter rate could not be applied to the lead-zinc ore with any profit to ourselves. The Judge mill of the Park City Mining & Smelting Co., with which we were affiliated, was running to capacity; if we built our own mill it meant a 5-mile freight haul to a satisfactory millsite and a year's delay. Fortunately, the International Smelting Co. had just inherited a mill at Tooele which, with some changes, was about double the capacity required for its own ores. Flotation tests were run on Park-Utah ore and a contract entered into with a low base treatment charge per ton, the tariff being largely fixed by the metallurgical deductions. This contract has been admirably calculated so that the miner can follow a lean orebody to its limit. Such a procedure has no doubt made it difficult for the smelting company at times, but it has resulted in finding ore extensions that otherwise might have been missed, so in the long run it has profited too. A flat rate per ton would have been like mining up to the claim endlines in a great many of the stopes. In order to offer such a contract it can be inferred that the smelting company must have been able to make high recoveries and high-grade products on a very lean ore.

Jan 1, 1928

ASDIE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows: the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal. Robert W. Hunt Medal and Prize The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the subcommittee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A subcommittee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered by the Iron and Steel Division. Awards of the medal have been made as follows: 1920—Robert Woolston Hunt. 1926—Charles Lewis Kinney, Jr. 1928—John A. Mathews. 1929—Edgar Collins Bain. J. E. Johnson, Jr., Award This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practice, vice-chairman

Jan 1, 1929

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By T. E. Leontis

Several publications1-7 during the past few years have demonstrated the markedly greater effect of cerium, as compared to all other alloying elements, in enhancing the strength and creep resistance of magnesium at elevated temperature either with or without the presence of other elements. In the work reported in Ref. 1-6, the cerium was added in the form of Mischmetal, which contains all the rare earth elements in essentially the same proportions as they occur in monazite sand, the principal ore of these metals. Mellor and Ridley7 have presented the creep characteristics at 200°C of magnesium alloys prepared both with pure cerium and with Mischmetal. Up to the present time, however, no comprehensive study of the effect of the various component elements of Mischmetal on the properties of sand-cast magnesium has been made. This hiatus in magnesium technology undoubtedly is associated with the difficulty in obtaining the rare earth metals separately. This investigation provides such a survey, the object of which was to determine which of the elements present in Mischmetal contributes the greatest effect in developing high strength and high resistance to creep at elevated temperatures. Toward this end the compositional variation of these properties has been determined as a function of temperature in the following alloy systems: 1. Magnesium-Mischmetal 2. Magnesium-cerium-free Misch- metal 3. Magnesium-didymiuin 4. Magnesium-praseodymium- lanthanum 5. Magnesium-cerium 6. Magnesium-lanthanum This designation, based on the names of the metals as furnished by the producer, is used throughout the paper in order to avoid the complicated system of listing all the elements present in the more complex alloys. The composition of the metals and the alloys is discussed in detail below. Preparation of Alloys ALLOYING INGREDIENTS The chemical composition of each of the six alloying ingredients used to prepare the alloys reported in this paper is given in Table 1. In each case, the percent total rare earths, percent cerium, percent neodymium, percent praseodymium, and percent thorium were determined in addition to the listed impurities. The percent lanthanum was determined by difference from the total rare earth content and consequently includes the other elements (samarium, terbium, yttrium, etc.) present in Mischmetal. These additional elements, however, seldom amount to more than 1 to 2 pet of the total rare earth content of Mischmetal. The iron content of the Mischmetal is considerably lower than that of the other metals. This grade of Mischmetal is now readily available. The metals are listed in the order of decreasing complexity. Elimination of the cerium from Mischmetal results in what the trade calls "Cerium-free Mischmetal." Carrying the separation a step further by eliminating the lantha-

Jan 1, 1950