Search Documents

By J. E. Stukel, J. Cocubinsky

A CONSIDERABLE amount of information is available on the equilibrium distribution of manganese between slag and metal under oxidizing conditions. These data have increased our knowledge of the manganese reactions in the open hearth, ladle, and ingot mold. In contrast, there is a paucity of data on the slag-metal distribution of manganese under reducing conditions. The purpose of the present investigation was to study the equilibrium distribution of manganese between blast-furnace type slags and iron saturated with carbon. Experimental Method Furnace: The induction furnace used for the experiments is shown in Fig. 1. A 1 in. pipe, attached to the transite cover, was fitted with a window through which the charge could be observed. Material could be introduced into the furnace through a tee and plug without removing the cover. A graph-it cylinder (3 in. ID and 10'/2 in. long), centered within the induction coil, was used as a heating element. During a test, a zircon plug kept the top of the furnace from becoming too hot from heat radiation. At the bottom, a graphite block on the vertical center line of the furnace and extending 1 1/2 in. into the coil, was used as a support for the graphite crucibles containing the melt. The graphite crucibles, machined from regular carbon electrode stock, had a 2% in. OD with 3/16 in. walls and were 5% in. long. The fumes present in the furnace during the early part of a run made optical readings uncertain. A noble metal thermocouple was, therefore, adopted to measure the temperatures. The arrangement used, shown in Fig. 1, allowed the silmanite protection tube to be replaced with a minimum effort. The thermocouple was calibrated against a standard Pt-Pt-Rh thermocouple in a fused quartz protection tube. The latter was inserted in the molten iron by removing the glass window on the cover. The lower couple was found to be very sensitive to temperature changes. To insure accurate temperature readings, the graphite crucibles were made to fit tightly against the silmanite protection tube. Further, to avoid contamination of the thermocouple by carbon, the silmanite tube was changed and the calibration procedure was repeated at frequent intervals. By using this temperature measuring technique, the furnace was easily held within *1O°C of the desired temperature. Because of the small free space in the furnace, no attempt was made to control the atmosphere. It

Jan 1, 1955

By L. Zwell, H. A. Wriedt

In describing their procedure for measuring the lattice parameters of solid solutions, Abrahamson and Lopata report (p. 77) the final heat treatment of their alloy specimens as "700°C for 100 hr, followed by a furnace cool". The isothermal part of this treatment may be expected to precipitate solute in excess of the stable a solid-solution limit at 700°C; the subsequent slow cooling is likely to reduce the dissolved solute still further. Fig. 1 (upper) presents the data for titanium alloys so he;rt-treated and shows the lattice parameters of solid solutions containing up to 3.5 at. pct Ti; Fig. 17 (lower) shows 2 at. pct Ti as the solubility limit in a iron at 700°C. Figs. 1 and 17 are thus incompatible. The paper contains comparable incon~patibilities for zirconium alloys, for niobium alloys, and for tantalum alloys. The final heat treatment at 700°C may also be responsible for the anomalous "knee" in the lattice-parameter data for nickel alloys, Fig. 3. The "knee" composition is located near the 700°C limit of the stable a solid-solution field;37 alloys of the experimental composition range with more nickel than the "knee" composition are two-phase at 700 C and prolonged heat treatment of them at 700°C would tend to produce inhomogeneity rather than homogeneity. In Figs. 4 and 7, the composition ranges of the zirconium, hafnium, and niobium alloys examined terminate at alloy concentrations of 0.1 to 0.2 at. pct. These metals form very stable oxides and their partial removal from solid solution in iron by impurity oxygen may be expected. We believe that the authors should have reported the procedure by which they distinguished the amounts of alloying elements in solution and in oxide. The diagrams pertaining to copper in Figs. 3 and 18 (lower) are almost certainly incorrect. Three recent investigations of this system38-40 all substantially agree on the solubility of copper in a iron, finding it to be much larger than that reported by Abrahamson and Lopata. The change of the lattice parameter with composition reported by Abrahamson and Lopata is too large by a factor of three to five, as seen by comparison with the findings of other investigators.41738 Moreover, the authors violate, in Fig. 18, the accepted Fe-Cu constitution diagram37 by ignoring the eutectoid at about 850°C.

Jan 1, 1967

By Lucien Eaton

The use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material must be used. In different parts of the world sand, clay, gravel, culm, granulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, but to describe some of the methods used for placing sand fill and to make a brief comparison of their merits. Methods of Placing Sand Sand may be transported and placed underground by several methods, which may be classified as follows: 1. By Hand.—The sand, which must be comparatively dry, is taken down the shaft in cars on cages and is distributed to its destination in these cars, or it is dumped down raises and is drawn off and distributed by means of cars, wheelbarrows or scrapers.

Jan 1, 1932

By J. R. Long, T. R. Graham, C. W. Matthews, R. S. Dean

IN a previous paper§ the authors reported on the mechanical properties of a 65 per cent copper, 10 per cent manganese, 25 per cent zinc alloy as compared with similarly processed cartridge brass. Additional investigations by these laboratories, on higher copper alloys, have demonstrated that at lower zinc concentrations even larger amounts of pure manganese may be added to copper-zinc alloys without exceeding the single-phase solid solution limits, and that similar increases in tensile strength, yield strength, and hardness may be obtained without excessive decreases in ductility. Several compositions in this range showed also a decided color change with increasing manganese. The normal "brassy" color was considerably lightened and reduced to a faint yellow cast at 15 per cent manganese. With higher manganese contents the alloys were essentially white and similar in appearance to the nickel-silver alloys. From this work it appeared that it would be desirable to determine more completely the properties of the wrought and annealed white alloys. Accordingly, a more detailed study was planned of an alloy having the composition 70 per cent copper, 20 per cent manganese, and 10 per cent zinc. This alloy remained single-phase throughout the working and annealing cycles of the preliminary tests and appeared to be about the strongest of the white single-phase alloys. The project included also an investigation of additional alloys, deviating from this composition by 5 per cent of each of the three components to evaluate the effects of variation in composition; also a study of the properties of the central alloy made with silicothermic manganese. MATERIAL PREPARATION Electrolytic manganese, wirebar copper, and electrolytic zinc were used for the preparation of the alloys. Representative analysis of the electrolytic manganese seldom exceeds 0.01 per cent iron, 0.02 per cent sulphur and 0.02 per cent lead, with no silicon or aluminum. A typical sample of the silicothermic manganese metal contained 2 per cent iron, 0.81 per cent silicon, 0.i6 per cent carbon, and 0.36 per cent aluminum. Melting and alloying were performed in a high-frequency furnace with magnesia crucibles. Melts were deoxidized with small aluminum additions and cast into 25-lb. slab ingots. Care was exercised in deoxidation to avoid excessive amounts of residual aluminum, which has been found to have significant effects on alloys in this system. All ingots were hot-rolled at 1200° to 1300°F. and then cold-rolled with intermediate anneal-

Jan 1, 1945

By Thomas Clagett

THE Pocahontas coal field comprises the area in Tazewell County, Va., and Mercer and McDowell Counties, W. Va., in which Nos. 3 and 4 Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305m.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now, about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, io which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks off bone, each from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 25 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficiently well defined to exert an influence on the mining is rare. Overlying strata are slates, shales, and sandstones, the sandstones predominating, extending from .30 to 1000 ft. above No. 3 seam. The strata directly above the. draw slate of No. 3 seam, or "black rash" of No., 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the

Jan 5, 1922

By J. R. Long, T. R. Graham, C. W. Matthews, R. S. Dean

In a previous paper! the authors reported on the mechanical properties of a 65 per cent copper, 10 per cent manganese, 25 per cent zinc alloy as compared with, similarly processed cartridge brass. Additional investigations by these laboratories, on higher copper alloys, have demonstrated that at lower zinc concentrations even larger amounts of pure manganese may be added to copper-zinc alloys without exceeding the single-phase solid solution limits, and that similar increases in tensile strength, yield strength, and hardness may be obtained without excessive decreases in ductility. Several compositions in this range showed also a decided color change with increasing manganese. The normal "brassy" color was considerably lightcncd and reduced to a faint yellow cast at 15 per cent manganese. With higher manganese contents the alloys were essentially white and similar in appearance to the nickel-silver alloys. From this work it appeared that it would be desirable to determine more completely the properties of the wrought and annealed white alloys. Accordingly, a more detailed study was planned of an alloy having the composition 70 per cent copper, 20 per cent manganese, and 10 per cent zinc. This alloy remained single-phase throughout the working and annealing cycles of the preliminary tests and appeared to be' about the strongest of the white single-phase alloys. The project included also an investigation of additional alloys, deviating from this composition by 5 per cent of each of the three components to evaluate the effects of variation in composition and a study of the propertics of the central alloy made with silicothermic manganese. Material Preparation Electrolytic manganese, wirebar copper, and electrolytic zinc were used for the preparation of the alloys. Representative analysis of the electrolytic manganese seldom exceeds 0.01 per cent iron, 0.02 per cent sulphur and 0.02 per cent lead, with no silicon or aluminum. A typical sample of the silicothermic manganese metal contained 2 per cent iron, 0.81 per cent silicon, 0.16 per cent carbon, and 0.36 per cent aluminum. Melting and alloying were performed in a high-frequency furnace with magnesia crucibles. Melts were deoxidized with small aluminum additions and cast into 25-lb. slab ingots. Care was exercised in deoxidation to avoid excessive amounts of residual aluminum, which has been found to have significant effects on alloys in this system. All ingots were hot-rolled at 1200' to I300°F. and then cold-rolled with intermediate anneal-

Jan 1, 1945

By Martin T. Broome

INTRODUCTION The Luanshya Mine is situated in the southern part of the Zambian Copperbelt. The copper ore deposit is stratiform, and is preserved in a synclinorium known as the Roan/ Muliashi basin. Roan shaft (formally called No.14 shaft) is located at the eastern end of the syncline and is theoldest of the presently operating hoisting shafts, being sunk during the 1930's. It presently hoists some 45 per- cent of the total Luanshya Mine production. A cross-section through the shaft is shown in figure 1. The ore formation on the south limb is unmined on this section because until recently it was believed that such mining might cause damage to the shaft. This paper examines the influences of adjacent mining on this so-called 'shaft pillar', and describes the mechanics of subsidence of the pillar itself. GEOLOGY AND STRUCTURE Figure 1 shows the general form of folding in the vicinity of Roan shaft. The north and south limbs of the main syncline approach parallelism, with the bottom of the trough fairly smoothly rounded. The axis of the - trough plunges to the west-north-west at 6° - l0°. A brief summary of the major lithologies present in the Roan basin is given in table 1, however, the performance of the overall structure during progressive mining of the ore horizon is controlled by the following features in addition to the mining method. Intraformational Contacts These are characteristically weak in most geological environments. The BC/RL7 contact is an unconformity between moderately weak quartz-biotite schists below (unconfined compressive strength 40 - 80 MN/M 2), and strong quartzites above (U .C .S. 170-200 MN/M2) Subsequent formations are conformable, and planes of weakness are generally the result of contrasting lithology (see below). Weak Interbeds The Rt7, RL6, RL5, RL3 and RU2 horizons consist predominantly of quartzitic rocks, i.e. conglomerates, quartzites and argillites, and as such are generally strong and considered suitable for the positioning of development. Between these however, lie two much weaker dolomitic horizons, the RL4 and RU1. The Rt4 is the main hangingwall aquifer, and must be drained prior to mining. Drainage results in an extremely weak, blocky cavernous horizon which usually requires support if exposed by development. Similarly, the RU1 formation is comprised mainly of dolomites and dolomitic arqillites which are weak and cavernous. In the eastern part of the Roan/

Jan 1, 1981

By J. A. Herbst, K. Rajamani

INTRODUCTION Recent research has shown that popu- lation balance models hold considerabl e promise as a basis for accurate mill scale-up from laboratory batch grinding tests. It has been shown that entire product size distributions from large ball mills can be predicted from data obtained in tests in small mills with errors of less than one or two percent. This level of accuracy has been demonstrated for batch grinding scale-up (Herbst and Fuerstenau, 1980; Austin, 1973; and Malghan and Fuerstenau, 1976) and for continuous grinding scale-up (Herbst, et a1., 1976; Herbst, Rajamani and Sanchez, 1982; and Herbst, Rajamani and Lo, 1982) in commercial mills up to 14.5 x 32 feet. A procedure which has been proposed for commercial mill design using the population balance approach and specific power information is shown in Figure 1 (Herbst and Fuerstenau, 1980). Here batch grinding data (size distributions for various energy inputs) obtained in a small batch mill is input to an estimation program which determines the "best" set of breakage rate parameters from the data provided. In turn, these breakage rate parameters are input to a scale-up program along with traditional inputs such as: a) desired circuit throughput and product size b) circuit operating conditions including fraction of critical speed and fractional ball load, size distribution and % solids in feed and circulating load (if closed circuit). In addition, since the population balance approach relies on more detailed models of the grinding circuit sub- processes than the classical design methods do, it is necessary to provide input to the scale-up program on the nature of material transport through the mill (e.g. residence time distribution information) and classifier performance characteristics (e .g. selectivity functions). The scale-up program will make the design calculations including the selection of mill dimensions and drive requirements, will predict product size distributions throughout the commercial circuit and will provide information on the sensitivity of the design to errors in the design assumptions. In order to implement such a scale- up scheme it is necessary to have a computer program for parameter estimation and a program for scale-up prediction. A program which is suitable for parameter estimation, ESTIMILL, has been developed and tested on a wide variety of ores at the University of Utah. This program has been in use in

Jan 1, 1982

By William L. Fink, Kent R. Van Horn

Zinc is one of the effective elements introduced to enhance the strength of aluminum. This strengthening is principally attributable to the high solid solubility of zinc in aluminum and the pronounced variation of solubility with temperature. Consequently an accurate determination of the solid solubility curve is desirable. The solid solubility relations have been studied by numerous investigators. Shepherd1 first established the existence of a solid solution region at the aluminum end of the diagram (-v phase) by specific volume and microscopic determinations. Bauer and Voge12 published a constitutional diagram which showed the limits of solid solubility as determined by thermal and microscopic methods. Hanson and Gayler3 presented the aluminum-zinc diagram which is now most generally accepted (Fig. 1). Chill-cast samples were given thermal treatments designed to obtain equilibrium conditions, quenched, and microscopically examined. The solubility was placed between 15 to 20 per cent at 60" C., 20 to 22 per cent at 140" C. and 36 to 38 per cent at 270" C. Sander and Meissner decidedly modified the limits of the -y phase field of Hanson and Gayler's diagram by using similar methods on chill-cast specimens annealed for a shorter period of time. Tanabe,s utilizing dynamic hard-ness, electrical conductivity and dilatometric measurements of specimens at temperature, obtained values comparable to Hanson and Gayler's at room temperature, but appreciably lower at higher temperatures. Nishimura6 concluded from age-hardening results of aluminum-zinc alloy chill castings, which had been quenched from 400" to 500" C., that the solubility of zinc in aluminum at room temperature is less than 5 * Metallurgical Division, Aluminum Research Laboratories. 1 E. S. Shepherd: Aluminum-Zinc Alloys, Jnl, phys. Chem. (1905) 9, 504. 2 0. Bauer and 0. Vogel: Aluminum-Zinc Alloys, Int. Jn1. Melallog. (1916) 8, 101. 3 D. Hanson and M. V. L. Gayler: A Further Study of the Alloys of Aluminum and Zinc. Jnl. Inst. Met. (1922) 27, 267. 4 W. Sander and K. L. Meissner: ZII~ Kenntnis der Konstitution der Aluminium-Zinklegierungen. Ztsch. f. Metallkunde (1922) 14, 385. 4 T. Tanabe: Studies in the Aluminum-Zinc System, Jnl. Inst. Met. (1924) 32, 415 6 H. Nishimura: On the Age-Hardening of Aluminum-Rich Al-Zn Alloys. Mem. Kyoto Imp. Univ. (1924) 3, 133.

Jan 1, 1932

By W. G. Woolf, E. R. Crutcher

The electrolytic zinc plant of the Sullivan Mining Co. is in Government Gulch, at Silver King, Shoshone County, Idaho, in the Coeur d'Alene mining district, about one mile from the Bunker Hill smelter and about three miles from Kellogg. The Sullivan Mining Co., which owns both the zinc plant and the Star mine, is itself owned jointly by the Bunker Hill & Sullivan Mining & Concentrating Co, and the Hecla Mining Company. The Tainton high-density, high-acid process is used at this plant, therefore some parts of its flowsheet differ markedly from those of electrolytic plants using the low-density process. While it is a custom plant and has treated a variety of zinc concentrates originating from various sources in a number of states, it has obtained its main supply of zinc concentrates chiefly from the zinc-bearing ores of the Coeur d'A1ene mining district, of which the principal important sources have been the Bunker Hill and Star mines. Thus the main feed has been zinc concentrates obtained from complex lead-zinc-silver ores. For the year of 1935 the concentrates had the following composition: water, 9.5 per cent; Zn, 50.6; Pb, 3.3; Fe, 9.4; S, 31.0; Cu, 0.2; insoluble, 2.9. Flowsheet The concentrates are delivered to the plant in railroad cars, which discharge into storage bins directly under the track. Bottom-dump cars are dropped directly into the bins while a slip scraper, pulled by an air tugger hoist, is used to empty box cars. There are five storage bins for concentrates, each of approximately 300 tons capacity. At the bottom of each bin there are individual belt feeders that discharge onto a common conveyor belt, which in turn discharges to another belt that carries the concentrate onto a weightometer belt for weighing. Immediately after the weighing, the crushed oversize return from the roasters is added to the load on the belt and then the ground-up sweepings, lumps and roaster cleanings. An electromagnet at the end of this conveyor removes tramp iron from the feed. The belt discharges to a set of 30 by 12-in. rolls, which break up lumps or frozen chunks of concentrate, etc. Beneath the rolls there is a screw conveyor, which conveys the roll discharge to a

Jan 1, 1937

By O. N. Carlson, A. L. Eustice

The tensile properties of iodide vanadium were determined as a function of hydrogen concentration. It was shown that the presence of 10 ppm H is sufficient to cause embrittlement of vanadzum over a limited temperature range. The temperature of the observed ductility mininlum is approximately -l00°C, this being a function of strain rate and hydrogen concentration. The yield stress of hydrogenated vanadium is raised sharply in the brittle temperature range. THE present investigation was initiated to determine the effect of hydrogen on the tensile properties of high-purity vanadium as a function of temperature and the role of hydrogen in the brittle-ductile transition. Loomis and Carlson&apos; reported a change from ductile to brittle behavior in iodide vanadium at -110°C with a return of ductility at temperatures below -140°C. Vanadium wire containing 270 pprn of hydrogen was brittle at room temperature while wire containing 100 ppm was ductile under the same conditions. Roberts and Rogers&apos; reported a ductile-brittle-ductile fracture sequence in vanadium containing 400 to 600 ppm of hydrogen. Their data show that hydrogenated vanadium is ductile at 150"C, brittle at room temperature and ductile again at -196°C. Magnusson and Baldwin found a minimum in ductility in vanadium containing 80 ppm hydrogen from tensile tests performed at several strain rates. Information available on the vanadium-hydrogen equilibrium system4 is somewhat incomplete. The absorption of hydrogen is exothermic in accordance with the decline in solubility with rising temperature. The limit of solid solubility at temperatures below 400°C has not been determined due to the difficulties in obtaining equilibrium at these temperatures. Data on the hydrides of vanadium are rather limited. Roberts6 studied the structure of VD,., by neutron diffraction, and observed the ordering of the deuterium atoms below -65°C into a primitive cubic cell with a lattice constant about twice that of the disordered bcc vanadium solid solution. EXPERIMENTAL PROCEDURE Vanadium of 99.9 pct purity was prepared by the iodide refining process6 for use in this investigation. This vanadium contained the following analyzed impurities; <20 pprn calcium, 150 ppm carbon, 200 ppm chromium, 30 ppm copper, 10 ppm hydrogen, 200 ppm iron, <20 ppm magnesium, <20 ppm nickel, <5 ppm nitrogen, 150 ppm oxygen, <50 ppm silicon, and <20 ppm titanium. specimen Preparation—Tensile specimens were machined from swaged rods of iodide vanadium. The

Jan 1, 1962

Ellsworth Daggett, who joined the Institute in 1873, and had beeu a prominent figure in the mining profession of Utah and other Western states for many years, died in San Francisco, Jan. 5, 1923. Mr. Daggett was a contemporary and intimate friend of Clarence King, James D. Hague, R. W. Raymond, and other Nestors of the mining engineering profession prominent in the last quarter of the nineteenth century. He was born at Canandaigua, N. Y., May 24, 1845; graduated from Sheffield Scientific School in 1864; pursued post-graduate courses there for two years, and for one year at the Bergakademie, in Berlin. He was in active practice as mining engineer from 1866 to 1914, but devoted most of his time during the World War to the perfecting of a submarine torpedo. He was connected with the United States Geological Exploration of the Fortieth Parallel in 1870. The plates illustrating mining industry, Volume III of the reports of that survey, were engraved from drawings obtained in the field during progress of the survey and prepared for the engraver by Mr. Daggett. He operated the Winnamuck mine and smelter at Bingham Cation, Utah, in the early seventies; the mines and mill at Cusihuiriachic, Chihuahua, 18867; and the Berlin mine near Austin, Nevada, 1904-6. On June 24, 1874, Mr. Daggett married Miss June Spencer, of Salt Lake City, who survives him, residing in New Haven, Corn. Appointed United States Surveyor General for Utah by President Harrison, in 1888, he was the first engineer to hold that office in Utah. He reorganized the mineral division of the office, required the courses of mineral surveys to be referred to the true meridian determined by solar or stellar observations, and did much to improve the accuracy and reliability of such surveys. Mr. Daggett was a member of the Alta and University Clubs of Salt Lake City, and president of the latter from 1890 to 1892; he was also a member of the Century Club, New York. Through his instrumentality, irrigation was brought to considerable tracts of land in northeastern Utah, and Daggett County of that state is named for him. Re wrote numerous technical papers, and an economic review entitled "A Quarter of a Century of Prices," in which was shown the close relation

Jan 1, 1923

Ellsworth Daggett, who joined the Institute in 1873, and had beeu a prominent figure in the mining profession of Utah and other Western states for many years, died in San Francisco, Jan. 5, 1923. Mr. Daggett was a contemporary and intimate friend of Clarence King, James D. Hague, R. W. Raymond, and other Nestors of the mining engineering profession prominent in the last quarter of the nineteenth century. He was born at Canandaigua, N. Y., May 24, 1845; graduated from Sheffield Scientific School in 1864; pursued post-graduate courses there for two years, and for one year at the Bergakademie, in Berlin. He was in active practice as mining engineer from 1866 to 1914, but devoted most of his time during the World War to the perfecting of a submarine torpedo. He was connected with the United States Geological Exploration of the Fortieth Parallel in 1870. The plates illustrating mining industry, Volume III of the reports of that survey, were engraved from drawings obtained in the field during progress of the survey and prepared for the engraver by Mr. Daggett. He operated the Winnamuck mine and smelter at Bingham Cation, Utah, in the early seventies; the mines and mill at Cusihuiriachic, Chihuahua, 18867; and the Berlin mine near Austin, Nevada, 1904-6. On June 24, 1874, Mr. Daggett married Miss June Spencer, of Salt Lake City, who survives him, residing in New Haven, Corn. Appointed United States Surveyor General for Utah by President Harrison, in 1888, he was the first engineer to hold that office in Utah. He reorganized the mineral division of the office, required the courses of mineral surveys to be referred to the true meridian determined by solar or stellar observations, and did much to improve the accuracy and reliability of such surveys. Mr. Daggett was a member of the Alta and University Clubs of Salt Lake City, and president of the latter from 1890 to 1892; he was also a member of the Century Club, New York. Through his instrumentality, irrigation was brought to considerable tracts of land in northeastern Utah, and Daggett County of that state is named for him. Re wrote numerous technical papers, and an economic review entitled "A Quarter of a Century of Prices," in which was shown the close relation

Jan 1, 1923

MEETING OF SAN FRANCISCO SECTION Twenty members were present at the meeting of the San Francisco Section, May 20, 1919. Chairman Bradley being in Alaska, vice-chairman, T. A. Rickard, presided. Prof. Frank H. Probert gave a short account of the activities of the governmental commission, consisting of himself, George S. Rice, and F. G. Cottrell, which recently visited Europe, and studied the coal, iron, salt, and chemical industries. When the work is finished reports will he issued. He gave a resume of the history of. the changes in nationality of Alsace-Lorraine and &apos;described the importance of the region for coal, iron, and potash. With the return of these provinces France will have an annual output of more iron ore than she has coke to smelt it with; hence, the importance of the Saar coal field. With these new mines France will take the predominant position in the iron and steel-industry formerly held by Germany. Many details were given of the devastated mines of France, and of their former value, production and the destruction that overtook them. Noteworthy is it that much of the damage was done as late as Oct. 28, 1918, for the express purpose of ruining the country industrially. The damaged area of the Valenciennes coal basin embraced twenty-four concessions, three were damaged by artillery bombardment, but have resumed operations since the&apos; armistice, nine had their surface: equipment destroyed by battle, pillage, and sabotage, while twelve concessions at the eastern-end of-the field suffered from wilful, systematic destruction. Of the 285 shafts in the district, 172 were flooded either by: turning surface streams into them, or, by wrecking the cuvellage; thus, admitting water and quicksand from the water-bearing strata above the coal measures. Two hundred and thirty-five surface plants were damaged, many of them to such an extent that they must be scrapped. These properties gave employment to 135,000 men before the war and, even admitting the remote possibility of getting workmen, the terrible destruction and devastation makes housing and living a difficult problem. It will probably be from 3 to 5 years before the mines are drained and information obtained as to underground conditions; to attain the pre-war output may require from 12 to 15 years.

Jan 8, 1919

By W. B. Plank

Those interested in training engineers for the mineral industry should consider how their men may fit into the general industrial recovery that now seems well started. One hears occasionally that too many engineers have been produced, especially mining engineers, and that the opportunities for their employment are decreasing. Just what is the situation? Enrollment in American engineering schools has fallen off sharply during the past few years. In 1930-31, the year of peak enrollment in all engineering schools, there were 78,685 engineering students in the United States, but in 1932-33 only 67,584, a decrease of 14 per cent. President Walters, of the University of Cincinnati, in his survey of 74 engineering schools, published in School and Society of Dec. 16, 1933, estimates that the engineering enrollment for 1933-34 is 10 per cent under that of 1932-33, or about 60,000. The situation in the mineral .ethnology schools somewhat parallels this general trend, although not to the same degree. Last year there were 4443 students in mineral technology schools, compared with 4687 in 1930-31, a decrease of 5 per cent. This year, with 3995 students, the enrollment shows a decrease of 10 per cent from last year, or a decrease of 15 per cent from 1930-31. Enrollment has no doubt been influenced by the condition of the mincral industry, just as the enrollment of other engineers has been affected by general industrial conditions. But the mineral industry, which is the first to recover, has not been so seriously affected as have some of the manufacturing industries during the past four years. This is especially true of coal and gold mining, which have been increasing rapidly in their production during the past year and have given employment to more men. Ten years ago, approximately 1,000,000 men were employed in the coal and metal mines and quarries, compared with probably half that number now. The number of mining engineering graduates in 1934 will be 234 and in metallurgy 252. In other words, fewer than 500 graduates are entering these industries the present year. With conditions improving in the mineral industry, coupled with a falling enrollment in our mining schools, there certainly exists an opportunity for young men now beginning their training for this industry.

Jan 1, 1934

By Roscoe C. Clark

In October 1945. R. F. Farris. in an AIME paper entitled Method For Drtermining Minimum Waiting OIL Cenzent Time, presented a method for caiculating the minimum WOC* time required in oil well cementing operations. Briefly. this method consisted of shutting in a well. after the cement had been placed and noting the time required fur the wellhead pressure to reach a. maximum. This time was then multiplied by a factor of 1.5 to determine when the cement had reached sufficient strength to support the weight of the casing. As a result of this work, a number of areas have reduced their WOC time ~Wuirements with the subsequent saving of considerable rig time. The tests conducted by Farris were, for the most part, conducted under cementing temperatures in excess of 70°F. This was done because in the overwhelming majority of cases. cementing temperatures are in excess of 70°F (only in tile northern part of the country. primarily in the Rocky Mountain ares. in cementing surface casing are temperatures below 70° F. encountered, and such temperatures occur only during the winter months). The Stano-lind Research Laboratory since that time has performed a number of tests both in the laboratory and in the field to evaluate this WOC factor when cemeriting temperatures are lower than 70°F. The results of these tests indicated the need for greater WOC time in areas affeaed by abnormally low cementing temperatures. These tests indi.cated that a woc factor of 2 (Time from start to mix cement to maximum wellhead pressure x 2 = Time to drill plug) will allow sufficient time for the cement to develop adequate strength. A field test under abnormally low cementing temperatures (surface temyerature 35°F., mud discharge temperature <70°F. and cementing depth 500 ft.) in the Rangely Field, "* using the WOC factor of 2, indicated the time to drill the plug as 45 hours. Well conditions preventing getting back into the well until a 48-hour WOC time had elapsed. At this time, the plug drilled firm to hard indicating that the cement had reached its final set. It is contemplated that during next winter additional field tests will be performed to further check the results of the laboratory and field tests conducted to date,

Jan 1, 1949

By W. M. Small

Austria.—Austria produced some 430 cisterns of 10,000 kg. each of crude oil of a 0.9428 sp. gr. during 1934. Gosting II well near Zis-tersdorf was placed on the pump in August and at the end of the year was still producing about three cisterns daily. This well is owned by the Erdöl-Produktionsgesellschaft while Gösting I is owned by Raky-Danubia. Only five wells were completed in the republic during the year. These accounted for 1783.5 meters of the 2225 meters drilled. The only producer completed was Gosting 11. At the close of the year, four rigs were in operation and one rigging up. At least 8 or 10 new wells are planned in Lower Austria for 1935. The European Gas & Electric Co. put its 6-km. gas line into operation in May and has sold 12,301,550 cu. m. of gas to the Vienna City Electric Works. A 2-km. pipe line was built from Gösting II to the railway loading rack near Zistersdorf. Hungary.—No oil or gas was produced except a small amount of gas trapped from flowing artesian wells. The Government completed and abandoned a 1500-m. hole at Tisztaberek in northeastern Hungary and is drilling at 967 m. near Bogáes, 120 km. northeast of Budapest. It is unofficially reported it plans to drill two new wells in 1935. The European Gas & Electric Co. has a rig up for a test at Mihalyi in Transdanubia. Czechoslovakia.—In Gbely (Egbell) there were produced 1283 cisterns of 10,000 kg. of 0.935 sp. gr. oil and a small amount of gas used for fuel. This field is operated by the Government; 17 shallow producing wells and three dry holes were drilled, with a total of 3351 m. of hole completed. In Hodonin (Goding) there were produced approximately 1300 cisterns of 10,000 kg. each of 0.91 sp. gr. oil and a small amount of gas used for fuel. The field is operated by the Apollo, which drilled four producing wells averaging 460 m. in depth, one small gas well of 550 m., one small gas well 260, and one dry hole 230 m. Two wells were deepened a total of 80 meters. The Government is drilling below 800 m. in a wildcat test in eastern Czechoslovakia near the Rumanian frontier.

Jan 1, 1935

By Gilbert P. Moore

The production of petroleum in Argentina during 1932 was greater than in any preceding year. The total amount produced was 13,012,-756 bbl. This figure represents a decided increase in the production of oil in Argentina and can be attributed largely to the increased activities of the Royal Dutch operations at Kilometer 27 in the Comodoro Rivadavia district and those of the Standard Oil Co. of Argentina in the Salta region. Production from the Royal Dutch wells amounted to considerably more than 10,000 bbl. per day over quite a long period during the year. Of the 13,012,756 bbl. of oil produced during 1932, the Government Agency (Y. P. F.) was responsible for some 5,578,954 bbl., while 7,433,-802 bbl. were produced by private companies. Although in 1930 the Y. P. F. produced about 55 per cent of the total production and in 1930 50 per cent of the total, in 1932 its production had fallen to about 42 1/2 per cent of the total. This decrease in the proportion produced by the Y. P. F. was not due to a decrease in its production but to the decided increase in the production of private companies, particularly those two whose names are given above. One new discovery was recorded during the year. This was a well drilled by the Y. P. F. at Cacheuta in the province of Mendoza which came in pumping 80 bbl. of 15" gravity oil from a depth of 673 meters. This well was completed at approximately the same time that the provincial government of Mendoza granted a concession to the Y. P. F. and declared the whole province as a reserve in which no concessions may be granted for a period of 10 years. Under these conditions, the federally operated Y. P. F. will have no competition in the Cacheuta area from private companies such as they have in the other three fields of the republic. The Y. P. F. wildcat west of Comodoro Rivadavia at Pampa Maria Santissima on the Rio Senguerr was completed as a dry hole during 1932. This we11 was reported as a producer in 1930 by persons returning to this country from Argentina but it appears that they had been misinformed. The site of this test has been abandoned and a new location made north of the Rio Senguerr.

Jan 1, 1933

By Roscoe C. Clark

In October 1945. R. F. Farris. in an AIME paper entitled Method For Drtermining Minimum Waiting OIL Cenzent Time, presented a method for caiculating the minimum WOC* time required in oil well cementing operations. Briefly. this method consisted of shutting in a well. after the cement had been placed and noting the time required fur the wellhead pressure to reach a. maximum. This time was then multiplied by a factor of 1.5 to determine when the cement had reached sufficient strength to support the weight of the casing. As a result of this work, a number of areas have reduced their WOC time ~Wuirements with the subsequent saving of considerable rig time. The tests conducted by Farris were, for the most part, conducted under cementing temperatures in excess of 70°F. This was done because in the overwhelming majority of cases. cementing temperatures are in excess of 70°F (only in tile northern part of the country. primarily in the Rocky Mountain ares. in cementing surface casing are temperatures below 70° F. encountered, and such temperatures occur only during the winter months). The Stano-lind Research Laboratory since that time has performed a number of tests both in the laboratory and in the field to evaluate this WOC factor when cemeriting temperatures are lower than 70°F. The results of these tests indicated the need for greater WOC time in areas affeaed by abnormally low cementing temperatures. These tests indi.cated that a woc factor of 2 (Time from start to mix cement to maximum wellhead pressure x 2 = Time to drill plug) will allow sufficient time for the cement to develop adequate strength. A field test under abnormally low cementing temperatures (surface temyerature 35°F., mud discharge temperature <70°F. and cementing depth 500 ft.) in the Rangely Field, "* using the WOC factor of 2, indicated the time to drill the plug as 45 hours. Well conditions preventing getting back into the well until a 48-hour WOC time had elapsed. At this time, the plug drilled firm to hard indicating that the cement had reached its final set. It is contemplated that during next winter additional field tests will be performed to further check the results of the laboratory and field tests conducted to date,

Jan 1, 1949

By V 7. 0 / 300 dpi

WHEN the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick -was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of all average sample of this quartz is: SiO2,, 96.7; Fe203, 0.3; Al203, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then clumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the. material would not be plastic enough to mold. After a few minutes&apos; grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected

Jan 9, 1913