Search Documents

By J. O. Brittain, E. P. Lautenschlager, F. Felberbauer

This investigation was undertaken to evaluate the effect of a dispersed phase in a iron upon the strain hardening and the stress dependency of dislocation velocity as inferred from the strain-rate sensitivitv. Experiments were made in a-iron specimens with controlled amounts of carbon and/or A12O3. They were tested at various temperatures between 195' and 373 'K under a variety of conditions oj-concentration, strain rate, and quench aging. The resulting yield strength, flow strength, and strain hardening increased with addition of Al2O3. The parameter m, measured from changes in strain rate, was xsed to describe the stress dependency of the dislocation velocity. m was found to increase with additions of A12O3, increasing carbon in solution, and with increasing temperature. When applied to a recent model for yielding based upon dislocation multiplication and velocity characteristics, the values of m alone did not successfully predict yielding for the materials of this investigalion, but had to be adjusted with a consideration of the number of unlocked dislocations nucleated heterogeneously at discontinuities or inclusions. The change of yield strength with Al2O3 Interpar-ticle spacing appeared to obey a theory of Orowan. EVER since the concept of dislocations has been introduced to explain plastic deformation in crystalline materials, the origin of dislocations and the source of the number of dislocations required to account for plastic deformation have been persistent questions. Ruling out the possibility of homogeneous nucleation,' Gilman2 drew attention to the various cases of heterogeneous nucleation as the source of dislocations, whereas Frank and Read3 introduced the Frank-Read source. However, Gil-man found that the Frank-Read sources did not play a dominant role in the deformation of LiF crystals, but that small precipitates are often, if not always, associated with the nucleation of dislocations. In LiF crystals, however, most of the dislocations arose through the multiplication of moving dislocations in a mechanism described by Koehler4 and Orowan,5 Thus, relatively few precipitates could account for a large number of dislocations. A similar observation of dislocation nucleation at inclusions of precipitates was made by Stein and LOW' on Si-Fe crystals. Their crystals contained

Jan 1, 1964

By Franklin J. Kay

Introduction The methods used in surface, mining vary throughout the world, depending on many variables such as: the types of over- burden materials, the depth of the overburden, the thickness of the seam, and other operational choices, both financial and functional. However, the stripping machines are typically draglines, stripping shovels, excavators, scrapers, loaders, and bulldozers. In all cases the economic feasibility of mining thin seams depends on the market needs, the market location, the equipment used, the mine management, the quality of the coal, and the labor market. Slight negative combinations of these parameters have closed many mines while positive combinations allow others to exist. The limited mobility or slow movement of large stripping shovels, draglines, and bucket wheel excavators make them more economically fitted to areas where large quantities of overburden are to be moved. This is necessary to keep the transfer and setup time between pits a negligibly small percent of the total operational time. Equipment such as the scrapers, loaders, backhoes, trucks, and bulldozers that are either very mobile or can be trailered is more versatile and can be used in the smaller area mines.* Mobile equipment is also more practical in areas with shallow overburden because of the constant movement required while removing overburden. In thin coal seams the equipment is usually paired such that the operational equipment can be listed as: (1) dragline-loader, (2) shovel-truck- loader, (3) scraper-loader. (4) loader-truck-loader, or (5) loader-loader. In these operations the overburden is removed with the first machine(s) of the pairing and the loader or loaders are used for coal production. Recent articles in Coal Age (Chironis, 1978) and Mining Engineering (Wiebmer, 1978) have discussed varying philosophies in mining similar seams of coal. One operator uses draglines for competitive mining while the other uses scrapers for the same purpose. Both cite strong cases sup- porting their choice of equipment as good sound economic decisions and their success supports their choices. The drag-line operation is adding new larger draglines to decrease the cost of mining, rather than to increase coal production. The scraper operation has also gone to more and larger scrapers for basically the same reasons. These operations and all

Jan 1, 1981

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By A.A. Grubb, F.L. Wolf

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By F. L. Wolf, A. A. Grubb

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By H. S. Gibson

A PROCESS that has come to be known locally as "multistage stabiliza-tion" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It con-sists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation, (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1939

By W. E. Crawford

The Fresnillo Company's mill at Fresnillo, State of Zacatecas, Mexico, treats oxide ores from the Fresnillo mine, dump ores and underground ores from the Plateros district, company leases and custom ores from the Zacatecas district, custom ores from other districts and tailings from old dumps at Fresnillo. The normal capacity of the mill is approximately 2600 dry short tons per 24 hours (a ton of 2000 lb.). The final product of the mill is a precipitate containing gold and silver, which is smelted and shipped as doré bullion to the refinery of the Compania Minera de Penoles, S.A., at Monterrey, State of Nuevo Leon, Mexico. The geology of the district was described in 1923, by T. C. Baker,' from whose paper the following data have been taken: The mineralization of the district was effected in the Tertiary period, following the intrusions and preceding the appearance of the flows. The area within which productive veins have been found is 1 mile long by 1/2 mile wide. The important units of each of the four general fracture systems meet in the central portion of Proano hill, which is an outcrop of graywacke, and where the rock was also intensely fractured by subsidiary movements, resulting in a shattered zone 1200 ft. long by 400 ft. wide. The mineralization was more intense in the immediate vicinity of the principal channels through which the solutions rose. The valuable metals are silver and gold, the ratio by weight of the former to the latter being 1000 to 1.5. Argentite is the predominant silver mineral, and is associated with pyrite and manganese mineral. The sulfides are primary throughout. A slight secondary action is represented by small quantities of native silver and silver halides, principally cerargyrite, which are found in the upper part of the mine. Oxidation has penetrated with great thoroughness to the lowest horizon so far exposed, this being 420 ft. below the present ground-water level. The shattered mass within the central portion of the hill and near the surface was sufficiently mineralized to produce a large stockwork

Jan 1, 1935

By N. R. Pillai, T. R. Anantharaman

THE striking alterations in the constitution and structure of cast A1-Si alloys brought about by addition of small quantities of some elements, particularly sodium, have been extensively investigated. Many theories' have also been propounded to explain this so-called lLmodification" process, but their main concern has been more to throw light on the action of sodium than to arrive at general criteria underlying this interesting as well as intriguing phenomenon. Such theories have generally dealt with one or more, but not all, factors that seem to have a direct or indirect influence on the cast structure of A1-Si alloys, e.g.., formation of ternary eutectic, removal of oxides, hydroxides, and so forth, by fluxing, morphological changes in silicon, and inhibition of growth of silicon grains through colloidal action, compound formation, preferential adsorption, or reduction of surface tension. Kim and Heine2 were the first to study the modification of A1-Si alloys in a systematic as well as comprehensive manner and to list the important characteristics of a satisfactory modifier. According to them, an important property of the modifying element is its capacity to form a stable compound with silicon in the appropriate temperature range. Other subsidiary requirements are that the element should get adequately dispersed in the melt at the inoculating temperature and also must not form stable compounds with aluminum. The alkali elements, with the exception of lithium, fulfill these requirements most satisfactorily and have been shown to be successful modifiers by these workers. Sodium is the most effective of these and seems to be in a class by itself for various reasons noted by earlier investigators.37 None of the other elements tried by Kim and Heine, viz., Mg, Ca, Cd, Zn, In, Pb, P, As, Bi, S, and Se, showed any significant modifying action. We wish to report here briefly on substantial modifications in cast eutectic A1-Si alloys brought about by some V group elements, which do not comply with the Kim-Heine requirements. Aluminum and silicon used in the present work were indigenous and had purities of 99.8 and 99.5 pct, re-

Jan 1, 1969

By C. W. Mason

TIN has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphur. The notorious "tin disease," which Cohen1 has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white 0 tin to cubic gray a tin, has apparently encouraged the expectation that one or more addi-tional polymorphic modifications might exist. The search for confirma-tion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but for previous assumptions. The ball apparently was started rolling in 1880 by Trechmann,' who reported a new modification of tin (y tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be y tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller.3 Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,6 by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) and stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencer3 in 1921 examined the above evidence critically; he found similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on a second lot of crystals, not described crystallographically.)

Jan 1, 1939

By A. C. Callen

This, report represents the comments of the individual members of the A. I. M. E. Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institution of Mining Engineers (London). As might be expected, there is a certain diversity of opinions, for owing to the shortness of time- it was not possible for the sub-committee to get together for informal discussion. The report is presented in this form in the hope that it will bring out a full discussion by other members in the Institute. OLE SINGSTAD?, New York, N. Y.-The Atkinson formula, P =SV2 K a is quoted and it is stated that this formula is especially applicable to mine galleries but is unwieldy in application, as in many problems the value of K, S and a are assumed not to change. This is the same formula that was used during the preliminary calculations for the ventilation of the Holland Tunnel, and where the above-mentioned values were constant for a number of cases, it was a very simple matter to rewrite the equation n the form P = K1V2 and avoid the repeated use of identical figures. The Atkinson formula assumes 1. That resistance to flow is independent of the pressure. 2. Changes in volume due to change in pressure may be neglected. 3. Changes in density and viscosity may be neglected. 4. That the coefficient K is a constant. 5. That P is proportional to V2. We found, from our experiments in connection with the ventilation of the Holland Tunnel, that all the above assumptions could be safely made, with the exception of No. 3, and No. 4 at, very low velocities. In mine work, where many assumptions must necessarily be made, it would seem inconsistent to attempt to make any allowance for the other factors, which are so small that they can be determined only by the most careful experimental work. However, P does depend directly on the density of the air, and to that extent the Atkinson formula is incomplete.

Jan 2, 1926

By Frank Foote, Eric R. Jette

In a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be considered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe3O4 instead of the original Fe4O4. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously determined fact that the FeO lattice is ionic (i, e., consists of Fe++ and O? ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1. The purpose of the present investigation was to determine the limits of this homogeneity range by means of the X-ray structure analysis. This method has been applied frequently to the study of solid solutions by Westgren and his coworkers as well as by other investigators. The principle is simple: if the change in lattice constant with composition is

Jan 1, 1933

By R. W. Raymond

The Mining Law of New Pork, contained in Title XI., Chapter IX., Part One of the Revised Statutes, is as follows: Section 1. The following mines are, and shall be, the property of the people of this State in their right of sovereignty : (1.) All mines of gold and silver discovered, or hereafter to be discovered, within this State. (2.) All mines of other metals discovered, or hereafter to be discovered, upon any lands owned by persons not being citizens of any of the United States. (3.) All mines of other metals discovered, or hereafter to be discovered, upon lands owned by a citizen of any of the United States, the ore of which, upon an average, shall contain less than two equal third parts in value of copper, tin, iron, and lead, or any of those metals. Sec. 2. All mines and all minerals and fossils discovered, or hereafter to be discovered, upon any lands belonging to the people of this State, are, and shall be, the property of the people, subject to the provisions hereinafter made to encourage the discovery thereof. Sec. 3. All mines of whatever description, other than mines of gold and silver, discovered, or hereafter to be discovered, upon any lands owned by a citizen of any of the United States, the ore of which, upon an average, shall contain two equal third parts or more, in value, of copper, tin, iron, and lead, or any of those metals, shall belong to the owner of such land. Sec. 4. Every person who shall make a discovery of any mine of gold or silver within this State, and the executors, administrators, or assigns of such persons, shall be exempted from paying to the people of this State any part of the ore, produce or profit of such mine for the term of twenty-one years, to be computed from the time of giving notice of such discovery, in the manner hereinafter directed. Sec. 5. No person discovering a mine of gold or silver within this State shall work the same until he gives notice thereof, by information in writing to the Secre-

Jan 1, 1888

By R. E. Zimmerman

ALTHOUGH flotation of coal is considered relatively new in the United States by coal-preparation engineers, actually it has been practiced to some extent for the past 30 years, It is practiced much more widely in Europe than in the United States. Commercial plants are operating in nearly all major coal-producing countries of the world. A froth flotation plant has been operating since 1930 at the Champion No, 1 preparation plant of the Pittsburgh Coal Co. Unfortunately the term flotation is widely used in the United States by coal-preparation engineers to designate dense medium processes of coal cleaning. As used here, flotation means those processes for cleaning fine sizes of coal in which the coal is collected in a froth or matte at or near the surface of a pulp. The refuse particles remain in the pulp. Two distinct types of flotation are practiced: froth flotation and agglomeration. FORMS OF FLOTATION The theory of the principles of flotation and of the physicochemical foundations surrounding this process has become a complex and scientific field and coal-preparation engineers contemplating use of flotation processes would do well to study the works of Gaudin, 2, 5 Taggart, 3 Zimmerman, 4 Wark, 6 Ralston, 7 Petersen. 8 Bulk Oil Flotation.-In this process the separation of mineral from gangue is accomplished by virtue of the fact that minerals of metallic lustre, as sulphides, or hydrocarbons, as coal and graphite, are wetted preferentially by oil in the presence of water and consequently pass into the interface between oil and water; while gangue or rock is wetted by water and remains in the medium. Beginning in 1860 with Haynes and later between 1897 and 1907, at least 25 patents were granted for bulk oil flotation. Large quantities of oil are required, generally 3 to 25 per cent by weight of feed, and recovery of such oil is a major problem. The Elmore process 3 (1901 and 1902) is an example of a bulk oil process, The Trent process (1902-25) has been used for the cleaning of coal on a commercial scale, According to E. W, Davidson 9 there were five such plants operating in the United States by 1925. They have since been abandoned.

Jan 1, 1950

By John J. Croston

In the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 91/4c, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and preparations for rearmament in Europe and Asia acted as a further stimulus to purchasing. By midsummer the situation had so improved and stocks had been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the production quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining continuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 126 per pound, and since the turn of the present year has reached 17c. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By R. W. Parsons

wben a displacement front encounters an isolated permeability heterogeneity, it will be perturbed. The details of this perturbation will depend on the beterogeneity size and shape, the Permeability contrast, and the mobility ratio. This paper deals with the displacement front behavior for one, simple, mathematically tractable model: a circular permeability discontinuity and unit mobility ratio. The progress of an initially planar front is shown for four permeability contrasts: k2/k1 = 0, 5/2, 2, m. The front distortion is more pronounced than streamline and isopotential distortion and it approaches a constant shape downstream from the discontinuity. INTRODUCTION The impact of reservoir heterogeneities on oil displacing processes depends upon the variation of the heterogeneous property (frequency distribution), its disposition (spatial distribution), and the inherent stability of the displacement mechanism.l The interplay of these factors plus the impracticability, if not impossibility, of describing a natural rock system in any detail makes exact displacement front movements difficult to determine. It is useful, however, to be able to qualitatively visualize what heterogeneities will do to a displacement front. In this respect certain simple models that can be treated analytically are of value. The following analysis will show the displacement front behavior for one such model. MODEL DESCRIPTION The flow field is two-dimensional and infinite in extent. The fluid flow is single phase, steady state and unidirectional at x, y = 2 m, or before insertion of the discontinuity. A circular permea- bility discontinuity is placed at the origin. Porosity and thickness are the same within and exterior to the heterogeneity. This is exactly the same model that was used by Greenkorn et al. to check analytically Streamlines as determined by Heie-Shaw flow models and finite difference computer techniques.2 FRONT POSITION CALCULATIONS The results of displacement front calculations are presented in Figs. 1 through 4 for four different permeability contrasts: k2/kl = O, %, 2, m. The times corresponding to the front locations are the Same for the 0 and cases! and for the 1/2 and 2 cases. The determination of front positions at various times is based on known analytical expressions for velocity potentials ().2 and stream functions ().2 These expressions are in terms of the x and y

Jan 1, 1969

By R. G. Davies

Above 500°C, where dislocation climb is rate controlling, it is observed that the activation energy for creep is independent of the apblied stress, although it varies from 62 kcal per mol at 15 pct A1 to 73 kcals per mol at 20 pctA1 due to the change in short-range ovdw with composition. Below 500°C, when the nonconservative motion of jogs upon dislocations is thought to be rate controlling, the activation energy is stress dependent. A sudden increase in the creep rate, for which no explanation is availab2e, occurs at the highest stress at all temperatures. CREEP has been the subject of numerous research publications during the past decade with most of the attention focused upon high temperature steady state creep, i.e., above 0.5 TM, where TM is the absolute melting temperature, as it is the most amenable to theory. Many of the proposed theories involve the climb of dislocations out of their slip plane, which allows them to circumvent obstacles or to annihilate dislocations of opposite sign on other slip planes.' For pure metals it is observed that the activation energy for this creep is equal to the activation energy for self diffusion.' The position is much more complicated in alloys as there are many possible microcreep mehanisms, as well as dislocation climb, which could be rate controlling. There has been little systematic investi- gation of alloys, but Weertman (lead and indium base alloys)3 and Lawley, Coll, and Cahn (Fe-A1 alloys)4 suggest a microcreep process as the controlling factor. A Cottrell-Jaswon atmosphere mechanism is proposed for the lead and indium alloys, and a mechanism involving crystallographic order for the Fe-A1 alloys. Lawley et al. showed that the formation of a super-lattice, either of the FeAl or Fe3A1 type. decreased the rate and increased the activation energy for creep. From the measurements of lattice parameters,= resistivity,' magnetic properties,7'8 internal friction: and dilatometry10 the ordered region is thought to commence at -19 at. pct Al. However, a recent investigation by the author indicates a value

Jan 1, 1963

By M. W. Hayward

THE object of this paper is to record and tabulate the data and field observations obtained by the writers and their associates during 10 years of intensive study of lead-zinc deposits in the Cretaceous limestone areas in Northern Mexico, particularly in mines owned by the Cia. Minera de Peñoles, S. A. At the El Paso meeting of the Institute in October, 1930, J. G. Barry made the suggestion that a committee be appointed to correlate the ideas and theories which have been put forth by the numerous engineers and geologists who, during recent years, have made a study of the ore deposits in the area under consideration. The first step in a work of this nature would be to record all of the observed facts, and these facts would have to be accepted by those who attempted to formulate a theory of ore deposition. It is with this idea in mind that the writers have described as accurately as possible the actual, observed facts pertaining to the occurrence of the lead-zinc ores in dolomites or dolomitic horizons. By most writers the term "dolomite," is loosely used to designate magnesium-bearing limestones, regardless of the percentage of MgO present. Since no, true dolomites exist in the areas to be described, we shall also loosely use the terms dolomite or dolomitic limestone to designate those beds having a magnesia content of 5 per cent MgO or more. For a number of years the writers have been impressed with the fact that in areas where dolomite beds occur a large percentage of the lead ore is found in these beds, in spite of the fact that such beds may be overlain or underlain by pure limestone, which one would assume to be just as favorable for replacement as the dolomite, if not more 'so on account of its being more soluble in acid solutions than the dolomite. It is true that in some limestone areas, such as the Erupcion-Ahumada districts, Chihuahua, and Providencia, Zacatecas, where no dolomite beds have been found, large tonnages of lead ores have been mined. We venture to predict, however, that had there been dolomitic beds in these areas, the

Jan 1, 1931

By G. L. Kulcinski, R. D. Leggett

Irradiated uranium containing 635 ppm of carbon, mostly in the form of UC precipitates, was annealed at temperatures from 650" to 900°C under hydrostatic pressures of 0 to 1000 bars. Postirradiation examination revealed that the carbide particles are not stable in the r phase of irradiated material but are stable in unirradiated material annealed under identical conditions. The degree of carbide dissolution appears to be connected with the fission product concentration and independent of annealing pressure. THIS paper describes the change in appearance of carbide particles in irradiated uranium after the uranium has been postirradiation-annealed. It has been proposed by several investigators&apos;-5 that fission gas-induced swelling in irradiated uranium may be reduced by incorporating a fine dispersion of second-phase particles into the metal. Because of the low solubility of carbon in uranium6 and the apparent stability of UC precipitates at high temperatures,6-8 this system has received some attention. The stability of UC particles to low-temperature irradiation has been demonstrated many times, as well as their stability during postirradiation anneals in the high a or B phases.9 Unirradiated uranium containing UC particles has been annealed high in the r phase, and the solubility of carbon was found to be only -115 ppm at 1050ºC.6 Vacuum annealing of irradiated uranium to the same temperature produces a spongelike sample, due to the formation and growth of fission gas bubbles."14 This highly disrupted lattice has made any determination of the stability of UC at these temperatures impossible. Nevertheless, it has always been tacitly assumed that the UC particles were still present. Recently, postirradiation, high pressure-high temperature tests have been performed on irradiated uranium containing a secondary phase of UC. 14 Examination of these samples after 100-hr, 900°C tests revealed that the carbides are not stable, and the results of these tests are presented here. 1) EXPERIMENTAL PROCEDURE The samples, high-pressure equipment, and subsequent analytical techniques are the same as those described elsewhere.14,15 Briefly, cylindrical samples of commercial-purity uranium that had been irradiated at <350°C to 0.37 at. pct B.U. were subjected to 90O°C, 100-hr anneals in NaK at pressures ranging

Jan 1, 1970

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943