Search Documents

By Jan Knobloch

Inter Stand Cooling (ISC) can increase productivity of a HSM and improve final mechanical properties of the strip. Constant Target Exit Temperature can be ensured for the whole strip length eliminating skid marks and other temperature oscillations of the transfer bar. The paper deals with advanced control module of ISC. Essential mathematical models of the control system is introduced and basic functionality is explained. Temperature model is based on FEM. Mechanical and thermal properties of the strip are calculated from chemical composition using neural network. Further on an experimental possibilities for investigation and design of ISC cooling headers will be shown. In conclusion practical experience with ISC on various HSM will be discussed.

Jul 30, 2018

By Piezanowski Ludivine

With the aim to reduce the hot metal production cost, ArcelorMittal Gent decided to integrate more ores with finer particle size distribution in the raw material mix for the production of blast furnace sinter. As a consequence of such an increase of finer material in the sinter raw mix, the sinter machine productivity and the quality of the sinter are affected. In order to compensate this impact, modern granulation technology can be employed. Within this context, ArcelorMittal Gent has invested in a vertical intensive mixer. The equipment was placed before the existing drums, with a function of “mixer”, whereas the drums are fully optimised for the nodulizing process. The paper presents the results of the industrial operation during the commissioning phase of the new equipment. Gradually increasing the proportion of fine material in the sinter raw mix has made it possible to compare the performances of the old system using drums for mixing and pelletizing with the new system using an intensive mixer combined with a nodulizing.

Aug 1, 2018

By Hervé Thomasson

Siemens VAI has made an important Research & Development effort since 10 years on laser welder field. The last step of this program was in 2010, the evolution of its laser welder range by implementing the solid state technology with laser cutting and welding. Since this step, 8 welders were produced by Siemens VAI. Now after more than 1 year of industrial feedback, the results are showing a high level of performances on very demanding processing lines for a large range of products from Silicon steel to High Strength Steel with DP and TRIP grades. This laser welder concept using laser cutting and welding through solid state laser source is also proposed by Siemens VAI for pickling lines and tandem mills with significant advantages compared to standard solution.

Jul 30, 2018

By Esteban Ruisanchez Rodriguez

In this paper we will discuss the process of the grain size customization of the EBT filler sand in relationship to the technical characteristics of the furnace and its tap hole. By customizing the grain size distribution, the glassy area formed on the top of the tap hole varies and supports differently the metallurgical pressure of the molten steel providing increased free opening speeds. Taylor made sand improves therefore the free opening rate, reduces the tap to tap time and increases the lifespan of the tap

Aug 16, 2017

By Francisco de Paula Pinheiro

Estudo das fontes de variação do processo de vazamento contínuo de chapas de alumínio, através da aplicação de uma metodologia prática e rápida para solução de problema. Após identificação das variáveis críticas à qualidade, ações foram tomadas de modo a minimizar as perdas do processo, o que contribuiu para a redução nos custos de produção das chapas.

Aug 16, 2017

By Lucas Breder Teixeira

O uso de ferramentas de simulação numérica para análise estrutural vem se expandindo nos últimos anos, sobretudo utilizando o método dos elementos finitos. Nesse trabalho são apresentados dois exemplos de otimização de projetos envolvendo componentes de mecanismos de válvula gaveta, realizados pela Magnesita Refratários S.A. Partindo da geometria inicial até o produto final, é analisado como o campo de tensões é adequado a valores admissíveis, conforme modificações de projeto são realizadas. Por fim, é demonstrada a importância desse tipo de estudo para alcançar maior confiabilidade e segurança em projetos mecânicos.

Aug 16, 2017

By Luiz Alberto dos Santos

. In this work, samples of the alloy with composition of 50.9 % at. Ni were machined and were subjected to hot tensile test, after the machining all the samples were solubilized so that all were in the same condition during the hot tensile test. The hot tensile tests were performed between the temperatures 350-650°C and the yield stress were between 800 and 597.1 MPa and area reduction between 17 and 75% with respect to the initial area. The test at 350°C shows a fragile fracture characteristic while the hot tensile test above this temperature showed a predominantly ductile fracture. The fragile fracture is evidenced by the river marks that are characteristic of this type of fracture, because in this condition does not promote much plastic deformation. The higher temperatures present ductile fracture, because present the dimples that also characterize this type of fracture. This work shows the temperature relationship in the mechanical properties, more specifically the hot tensile test, in the NiTi alloy.

Oct 30, 2017

By Markus Reifferscheid

Industry 4.0, Digitalization, Internet of Things (IoT) and Cloud Computing are predominant topics in the world economy at the moment. At the ABM week 2017 Dr. Markus Reifferscheid, Head of Research & Development of SMS-group, will talk about the proceeding digitalization in the steel industry with selected examples of SMS-group. He will present advanced concepts and solutions which are currently being developed.

Oct 30, 2017

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By André de Cabral Oliveira

With the onset of the global economic crisis in 2008, and more precisely from 2009, production routes in iron making as blast furnace, sinter and coke oven, indicated a significant increase in frequency as well as intensity of undesirable incidents. The cost impact of such deteriorations of the production chain cause significant losses ranging up to several hundred million dollars annually. On the other hand, opportunities for processes improvement are contributing to enhance process efficiency and results, and also reduce or even avoid losses from unexpected incidents. The use of specialized services for processes has gained projection along the plants and emerged as an attractive alternative to increase results by increasing the performance and reducing costs and expenses. Process Services are formatted to achieve cooperative and customized solution during planned or urgent interventions, conducting feasibility studies, process improvement, training, among others, providing knowledge, information and crucial actions to preserve and optimize processes and plant facilities.

Aug 2, 2018

By Daniel Augusto Godinho de Carvalho

At thyssenkruppCSA, a positive heat balance at BOF process is faced, mainly because of low utilization of scrap and plant design. A singular logistic concept for hot metal transport between blast furnace and steel plant was established to optimize transportation and energy balance. Up to 80 kg of iron ore pellets/t steel is necessary for 340t BOF heat balance. In order to accomplish this challenge a stable blowing process, intensive operational development have been successfully executed: slopping rate reduction of 80% achieved without changing the blowing time. This paper describes steps and results of this development.

Oct 30, 2017

By Mariana Macedo de Oliveira Lima, Pedro Emílio Gazola, Andrei Locatelli

Boron steel is used in the industry due to its great wear and impact resistance. During the hot rolling production of 15B29 steel flat bars it is a recurrent problem that the bars will present warping while on the cooling bed. Control this phenomenon is an opportunity to have better productivity, preventing metallic losses. Through the observation of the macro and microstructure samples produced with different reheating temperatures and cooling rates, it was found the presence of residual stresses and cracks on warped bars macrostructure. The residual stresses appearance suggest that the material cooling is too fast. Billets temperature on the reheating furnace of 1230°C reduced to 1100°C and the production pace slowed down. Bars temperature when arriving the cooling bed was reduced from higher than 670°C to 625°C. The results obtained made it possible to produce the material with better quality, reducing the warping effect at the cooling bed. The major influence on the materials warping was identified as the cooling rate at the cooling bed and the reheating furnace temperature was adjusted to provide a homogeneous temperature along the bars.

Oct 1, 2019

By Maycon Athayde

Samarco produces high quality iron ore pellets processed in straight grate furnaces. This process is essential in order to obtain adequate mechanical strength to the pellet transportation and operation in the reduction reactors. All mechanical properties of the agglomerates are obtained during the stage of firing where the slag and sintering bond happens, thus it is a decisive step to improve the pellet quality. Therefore, the velocity distribution of gas flow within this zone must have homogeneous and even velocity distribution. Hence, it was developed a mathematical CFD model to characterize the gas flow in the burning zone, applying the equations of conservation of momentum, mass and energy and an uneven flow distribution was identified and the gas velocity analyzed and validated through experimental data. On the other hand, on the present paper, an improved firing zone burner were developed and industrially implemented in a way to mitigate the uneven flow pattern detected aided by CFD. Different burner designs, based on CFD analysis, were experimented in order to succeed on the aggressive condition. The combustion was investigated and burner efficiency evaluated and compared with the simulation purposed.

Aug 2, 2018

By Hiroshi Ichikawa

In 2013, Nippon Steel & Sumikin Engineering Co., Ltd. (hereafter referred to as NSENGI), Tenova HYL and Danieli have entered into an agreement to combine ENERGION DR technology into blast furnace technology and/or with syngas technologies. This new alliance will allow the three companies to combine research and development activities with their respective expertise in ENERGIRON DR technology, Blast Furnace technology and Syngas (by-pro gas and coal gasification) technology, with the ultimate objective to develop breakthrough iron making technologies and create such EPC projects. This paper introduces the concepts and the features of our breakthrough technologies of combining of ENERGIRON DR technology, Blast Furnace technology and Syngas technology.

Aug 16, 2017

By Javier Martinez Rubio

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 16, 2017

By Edo Engel

Whereas only a handful of decades ago, typical blast furnace working volumes were below 1000 m³, such furnaces are currently designated compact or even mini blast furnaces. For certain business cases, however, small furnace sizes remain an attractive option. Decades ago, this size blast furnace would have produced a maximum of 0.3 Mtpa with its 600 m³ working volume over a campaign of up to four years. The current state of technology and operational know–how will allow a similarly sized furnace to produce over 0.7 Mtpa while achieving the multiple decade campaigns that have become familiar to steel producers in full sized operations. This level of productivity, but especially the reliability and supply security associated with mature technology, allows for integration into minimills or taking a first step towards a full scale BF–BOF integrated mill. Steel producers considering such scenarios, which are typically attractive for emerging economies, are confronted with fundamental decisions, one of which is for the technological basis for the compact or mini blast furnace to be included in the plant. This article addresses some of these decisions from an operations–based perspective. A small number of case studies is included.

Aug 16, 2017

By Antônio Aldenor Pinheiro Neto, Matheus de Lima Vieira

In mid-2015 the steel industry faced a strong crisis due to the weak performance of the Brazilian economy and the persistent entry of Chinese steel into Brazilian territory. This situation demanded that Brazilian steelmakers seek to develop products to meet new export markets. within the volume of exports possible are the rebars, where its applications are in the construction industry. One of the largest importers is Peru which has a large percentage of this export volume. This market demands as a priority requirement the surface quality of blue condition (low oxidation index) and mechanical properties normative.in order to meet the items required by the customer at a competitive cost, a vanadium microalloyed steel was applied to the hot rolling process without heat treatment after the last rolling pass. Where the great challenge was to achieve a high level of stretching without compromising the minimum limits of tensile strength. Assuming that the steel used is the correct one interventions were made on rolling parameters such as set-point temperature, residence time of pieces in the furnace, linear mass and rolling speed. All the changes made were based on statistical tools and practical tests. Finally, with the execution of actions generated from the statistical analyzes and tests it was possible to reduce process losses by 96%.

Oct 1, 2019

By Gilmar Zacca Batista

The present work is a part of a comprehensive program that aims to evaluate the girth welding procedures for heavy wall API 5L X65 pipes produced for sour service applications. This article describes the results of toughness, strength and sour resistance of girth welds produced with different welding consumables. The methodology applied included girth welds production with GTAW process for root pass using ER70S-6 consumable and FCAW process for filling passes using E71T- 1CJ and E91T1-GM-H4 consumables. Mechanical tests of Charpy, CTOD, tensile, hardness and stress corrosion cracking were also performed. The E71T-1CJ resulted in a girth weld with tensile and yield strength around 7% lower than the pipe. However, according to the papers analyzed at this study, a value up to 10% of undermatching could be acceptable. The CTOD and Charpy tests showed good toughness and weld metal embrittlement was not observed. The hardness and the stress corrosion cracking tests demonstrated that the consumable ER70S-6 is suitable for sour service. All properties evaluated met the requirements specified by the onshore pipeline standards, showing that the consumables ER70S-6, E71T-1CJ and E91T1-GM-H4 are suitable for the welding of heavy wall X65 pipe with sour service and toughness requirements. If an overmatching is required, the E91T1-GMH4 shall be used to assure a strength overmatching and prevent plastic strain concentration at the weld metal. The results provided by this paper can be used for consumable selection and for welding procedure qualification of pipelines construction when heavy wall API 5L X65 are used for sour gas transportation.

Aug 16, 2017

By Robert Horwood, Richard Harvey

The copper stave was a development of the Blast Furnace cooling system intended to utilise the high heat transfer properties of copper within a fully covered shell cooling solution. They were originally conceived as being able to provide a permanent cooling lining for use primarily in the higher heat zones of the Blast Furnace. Despite a large number of campaign successes around the world the everlasting concept has not proven universal, with some plants having suffered issues in two particular areas: stave bending (leading to water leaks at back of the stave) and stave wear (erosion on the hot face). Primetals Technologies have in the past been approached to provide assistance to a number of Blast Furnace operators who were experiencing operational issues with the copper stave furnace cooling systems of others. Through knowledge gained resolving these issues, and with the positive experiences of their own copper stave designs, Primetals Technologies have worked towards developing a new concept in copper stave design capable of providing a more robust solution to cope with the greater productivities of modern ironmaking. This paper will provide an outline to the concepts that have driven the design of this new technology.

Oct 1, 2019