Search Documents

By G. E. McElroy

This report discusses the construction and use of an all-pressure psychrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air-conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines - throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the atmosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heating and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure - 29.92 inches mercury.

Dec 1, 1947

By D Craw, S Clearwater, S Hammit, C Smith

Prior to rehabilitation, plant cover on quartz gravel overburden at Wangaloa coal mine was highly patchy. Stabilisation techniques have since considerably altered the condition of the main overburden yet deposits in the east and west remain largely intact. On the eastern overburden, three distinct zones of revegetation have naturally developed: Zone 1 represents a dense plant cover, Zone 2 a patchy cover and Zone 3 a sparse cover of isolated plants. Aerial photographs show much of the eastern overburden was deposited between 1940 and 1960s. Yet we found that the temporal scale of deposition did not wholly account for the differences observed in vegetation development. To investigate other influential factors, we set up 12 study plots using four replicates in each vegetation zone. The diversity and density of plants in each plot were measured to quantify the degree of vegetation development. Samples from the substrate in each plot were collected using soil cores to a depth of 10 cm. Cores were analysed for indicators of nutrient availability, metal content and physical composition. We found that substrate chemistry varied between individual study plots, but showed little difference overall along the vegetation gradient. Substrate physical differences were much greater. The ratio of coarse quartz pebbles: fines was considerably higher in Zone 3 than other zones, and within zones where plants were not growing. Bulk density also increased successively from Zone 1 - 3. We found clear evidence for the reversed stratigraphy of excavation superimposed over the time scale of deposition, and the corresponding nature of fine particles. The rate of revegetation was therefore highly dependent upon the substrate composition of the last surface deposit from the dumping truck. Our data suggests an optimum ratio exists between inert coarse material and a fine matrix for progressive natural vegetation development on mine substrates.

Jan 1, 2004

By K Gordon, A Black

Two remediation strategies have been considered to reduce the levels of acidity and dissolved metals in acid mine drainage discharging from Sullivan Mine, West Coast, New Zealand. The oxidising strategy involves adding alkalinity and dissolved oxygen (DO) resulting in the precipitation of metallic oxides and decreased acidity. The reducing strategy involves removing DO, resulting in the precipitation of metallic sulfides, followed by addition of alkalinity to decrease acidity. Field remediation trials indicate a reducing system may be more effective for this site than an oxidising system. A residence time of only two hours in the limestone layer of a successive alkalinity producing system (SAPS) is sufficient to reduce acidity by 100 per cent, iron by 71 per cent, aluminium by 59 per cent, nickel by 38 per cent and manganese by 26 per cent. The proposed remediation plan will likely include a series of SAPS, followed by an anoxic limestone drain, and settling ponds to capture any remaining precipitates.

Jan 1, 2003

By I. I. Beloglazov, G. A. Iusupov, A. Ju. Feoktistov

"The aim of this paper is to study the numerical modeling of the crushing process in a jaw crusher with complex motion jaws using Discrete Element Method (DEM). The main goals are to ensure the conformity of numerical simulation results to the experimental data, optimize the operating modes and the crusher design and develop automated verification and calibration methodology. It is offered to use automated selection of mathematical model parameters using large- or laboratory-scale experiments instead of deriving parameters from conventional intensive material tests (e.g. drop-weight test). Experimental data were obtained from a large-scale crusher designed and manufactured by the company “Mekhanobr-Tekhnika”. Both jaws have their drive shafts located asymmetrically; one jaw is driven in the upper part, the second at the base. The crushing process involves fragmentation of single smoothed rectangular granite particles of the same weight. During the experiment, the required parameters such as particle size distribution were obtained for further computer simulations. Based on the obtained experimental data, the Rocky DEM model was built. Simulation breakage parameters were calibrated using automated parameter selection methodology based on multiple set of parameter-controlled simulations. A good correlation of the experimental data and numerical simulation data was obtained. The methodology in combination with well-known capabilities of simulation modeling will help reduce the research time in the development of new mineral processing equipment.INTRODUCTION Preparation of rock mass for enrichment includes the power-consuming processes of crushing and grinding. Initial rock mass crushing is performed by means of drilling and blasting operations. To reduce the average size of a rock piece, primary crushers, mostly jaw crushers, are further applied. The advantages of the jaw crusher are simple design, easy maintenance and repair. One of the drawbacks is large oscillating masses and, thus, high power consumption during operation (55 - 200 kW). Jaw crushing simulation will help optimize the crushing process and improve further rock transportation and processing performance."

Jan 1, 2018

By J. Chai

In order to find the behavior of dewatered unconsolidated strata during the process of injecting water through a borehole, a new type of fiber Bragg grating (FBG) sensing system was successfully used for the real-time strain monitoring of unconsolidated strata during a water injection process for a dewatered unconsolidated strata of a coal mine. The unconsolidated strata water injection test was implemented through a borehole at a depth of +115.83 to +135.15m. The employed FBG strain monitoring system and ground water level observation system were installed at the depth in the unconsolidated strata where the water injection was conducted through two different boreholes. The water injection pressures in the test were 0.1, 0.2, 0.3MPa respectively, and the total water injection volume was 4226.84m3. The relationships between the water injection pressures, water injection volume and the strain change of the unconsolidated strata, the stress and strain conditions of the unconsolidated strata before and after water injection, were analyzed. This paper presents the results of these tests, and shows that the dewatering compression of the unconsolidated strata is reduced with increasing water injection pressures and water injection volumes. Comparing the stress-strain conditions before and after water injection, it is found that the stress of the water injection strata is in tension, which confirms the theory that the settlement of the thick unconsolidated strata is directly caused by the reduction of ground water levels. The high sensitivity and stability of the FBG monitoring system used was able to realize the real-time strain monitoring of the water injection process within a deep unconsolidated strata. This FBG monitoring system and the test results presented are very important for understanding further treatment of settlement in unconsolidated strata.

Jan 1, 2012

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

Jan 1, 1969

By H Han, W Wang, E Zhou, D Duan

"In this study, physical, chemical and microscopic characteristics of high phosphorus oolitic hematite were studied firstly. Based on which, the new methods of high phosphorus hematite used in the æsolid state reduction by rotary hearth furnace - magnetic separationÆ and iron nugget by rotary hearth furnace direct reduction processes were discussed. The results showed that high temperature, low basicity and high carbon content is conducive for the apatite in iron ore to reduce into molten iron, but not conducive to the removal of phosphorus. Through optimisation of process parameters, dephosphorisation rate of high phosphorus hematite is more than 60 per cent by æsolid state reduction roasting-magnetic separationÆ process while that is up to 80 per cent by iron nugget process. This study can provide theoretical and technical basis on economical and rational use of high phosphorus oolitic hematite.CITATION:Han, H, Duan, D, Zhou, E and Wang, W, 2013. New methods for high phosphorus oolitic hematite dephosphorisation by direct reduction process, in Proceedings Iron Ore 2013, pp 391-396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By H. E. Powell

Basic data were recorded on the decompositions that take place during thermal decomposition of siderite (FeC03). Both the naturally occurring and a synthetically prepared mineral were studied by differential thermal, thermo-gravimetric, X-ray-diffraction, and chemical (including gas) analyses. Thermal decomposition was studied in the media of dry air, moist air, dry carbon dioxide, dry helium, and dry carbon monoxide and at atmospheric and at reduced pressures. Results showed the thermal decomposition of FeC03 to be an extremely complex process, dependent on environmental factors and side reactions that cannot now be completely controlled. Therefore, full understanding of the reaction involved must depend on additional research with advanced evaluation techniques.

Jan 1, 1965

By C. Velásquez, W. Bergholz, C. Spence, P. Lind

NuevaUnión SpA (NuevaUnión) is a development project located in the Huasco province of the Atacama region of Chile. It is held in a joint venture company owned 50:50 by Teck Resources Limited (Teck) and Newmont Goldcorp. It includes the Cu-Mo Relincho deposit and the Cu-Au La Fortuna deposit, with plans to utilise a single concentrator to be built at the Relincho site. The Relincho site is at an altitude of 2,000 masl and is 40 km from the La Fortuna site which is at an altitude of 4,100 masl. The project is currently completing a Feasibility Study and is reviewing equipment selection and flowsheet options. This paper is based on the current thinking, and design decisions will be finalized at the completion of the Feasibility Study. NuevaUnión is currently planning for phased operation, processing Relincho ore at 104 ktpd followed by processing ore from La Fortuna at 116 ktpd. Plans for the third phase include doubling the main processing lines and returning to Relincho ore at a processing rate of 208 ktpd. The NuevaUnión concentrator will incorporate comminution and flotation circuits that are being designed to maximize the overall economic value of the combined ore deposits. Major ore characteristics differ between the two ore bodies, such as ore competency, grindability, liberation grind size, pulp rheology, tailings properties, minerals and metals of value, as well as gangue mineralogy. Mineral processing choices have been made to optimise value from each deposit and the combined project. INTRODUCTION Between 2010 and 2013, two significant mining projects were being developed in Chile: Goldcorp’s El Morro project had recently finalized a Feasibility Study and, in 2011, had received its environmental approval for construction; and Teck Resources Limited’s (Teck) Relincho project was finalizing a Feasibility Study and preparing its Environmental Impact Study. Both projects were: Geographically close, at only 40 km apart. Considering similar infrastructure. Each was planning to have its own concentrator, tailings management facility, high voltage power line, port, concentrate transport system, seawater desalination plant and pumping system to mine site.

Jan 1, 2019

By C. Daly

The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course, ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course ? the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks. The term ?peer assessment? in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ?try and see? approach. Each student must describe in detail the process they undertook to achieve their final design ? hence the approach is independent of the discipline and/or project selected. Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ?run? is for feedback only during week six and hence no moderation is undertaken. It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students. Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks.

Jan 1, 2014

By C. Daly

"The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course,ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course - the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks.The term ‘peer assessment’ in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ‘try and see’ approach. Each student must describe in detail the process they undertook to achieve their final design - hence the approach is independent of the discipline and/or project selected.Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ‘run’ is for feedback only during week six and hence no moderation is undertaken.It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students.Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks."

Jan 1, 2014

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameters like commodity price, mining or processing cost, stripping ratio etc. The most important characterization of these push backs is that the inner most push back has the highest value per ton, the second inner most push back has the second highest value per ton and so on. These nested pits are generated based on the best estimates of grade within a representation of the ore body in a three dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduced a new algorithm that incorporates ore grade uncertainty during push back design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence.

Jan 1, 2007

By T H. Clark, R P. Doig, V. A. Saull, R B. Butler

Terrestrial heat flow has been determined for four boreholes in the Montreal area. The mean value of the results (uncorrected for glacial effects) is 0.790 ± 0.053 x 10-6 cal/ cm2/sec (95 per cent confidence limits). Thermal gradients were determined using a thermistor probe and d-c bridge, and also by a new method using a probe-contained phase-shift oscillator, the output frequency of the oscillator being a function of probe temperature. Thermal conductivity determinations were made on core from the boreholes, using a divided bar apparatus. INTRODUCTION T HIS paper concerns the terrestrial heat flow in the St. Lawrence lowland of Quebec, as determined from measurements on four of the numerous boreholes drilled in this region for gas and oil. The work has been supported by Geological Survey of Canada Re-search Grant 3-58, awarded to T. H. Clark and V. A. Saull. This sup-port is hereby gratefully acknowledged.

Jan 1, 1962

By Edward L. Beutner, Robert M. Crump

Benson Mines low-grade iron ore reserve is a replacement deposit within the Grenville gneisses of the Adirondacks. The average grade of the crude ore is about 23 per cent iron. The iron minerals are principally magnetite and hematite disseminated throughout the gneisses as discrete grains about 1 mm in size. Both the ores that are beneficiated by magnetic means and the non-magnetic ores that are treated by a gravity method of concentration are found in stratigraphically different positions but are mined from one open pit, which is about 2.5 miles long and 800 feet wide and are treated separately. The gneisses are described and named according to the distinctive mineralogy of each. Recognition of the gneissic types permits the interpretation of the structure as a northward-plunging syncline overturned to the west. A large subsidiary anticline-syncline complex occurs on the east limb of the major syncline. Iron minerals in sufficient quantity to be considered ore are confined to areas where the footwall rock has been overturned to become the hanging wall.

Jan 1, 1968

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By Xiaoning Yang, C David Pearson, Brian W. Stump

An experimental study of ground motion from explosions designed to remove overburden in an open pit coal mine is reported. The purpose of this study is a characterization of these ground motions in the distance range of several tens of meters to several kilometers. The investigation has focused upon both single cylindrical sources with different explosive configurations as well as arrays of charges in the production mode. Critical to this study of source configuration and coupling is experimental control of the individual explosions, the timing of the explosions and the geological properties. The height of the explosive charges, their depth and charge distribution were monitored in the field. High speed photography as well as velocity of detonation measurements were made on the multiple explosion source so that detonation of individual charges could be documented.

Jan 1, 1994

By D J. Corp

The Halmahera Contract of Work is a sixth generation contract held 82.5 per cent by Newcrest Mining Limited and 17.5 per cent by PT Aneka Tambang and takes in the Gosowong Project area. In 1991 Newcrest Mining Limited established a small exploration office in Jakarta and proceeded to seek exploration opportunities. The Halmahera area was identified as a substantial prospective ground position in a relatively unexplored area. In late-1991 Newcrest Mining Limited and PT Aneka Tambang agreed to explore in Halmahera. Initial field work commenced in July 1992. A vigorous ground reconnaissance programme led to the discovery of the Gosowong deposit a little over 12 months later in September 1993. In April 1997 the Contract of Work was approved covering much of the island of Halmahera. Between September 1997 and November 1998 activities were directed principally towards obtaining the necessary permits required to commence construction activities. Some particularly ambitious targets were set for achieving this outcome. An aggressive construction programme commenced in late-1998. Construction took place during a period of unseasonally high rainfall, which in itself presented additional challenges to the construction team. A key milestone for the project was achieved on 1 July 1999 when wet commissioning of the process plant commenced. Construction of the Gosowong Mine was achieved on time and within budget. A period of some six years elapsed from the initial discovery of the Gosowong deposit to the time of the first gold pour. Much of the permitting, construction and commissioning activity took place between September 1997 and July 1999. This coincided with a period of significant social, economic and political upheaval in Indonesia. During the construction period a high level of importance was placed on the structured recruitment and training of local people, as well as fostering appropriate community and local business development programmes in the communities nearby the project. Emphasis was also placed on environmental management with detailed long-term planning and progressive rehabilitation commencing during the construction phase. The permitting and subsequent development of the Gosowong Project has demonstrated that even during the difficult times, with commitment, it is possible for mining and exploration companies to conduct business in Indonesia.

Jan 1, 1999

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986