Search Documents

By W Blair, J Bosman

The measurement of ferrosilicon rheology and characterisation of the parameters that have a direct influence on medium rheology provide the basis for evaluating, comparing and selecting an appropriate size and shape of medium to maximise separation efficiency in a dense medium application. The role of medium viscosity on particle separation in both static and dynamic separators is illustrated using relevant theory. The primary measurements of rheology are medium viscosity and stability. These in turn are determined by particle size, particle density and particle shape which in turn can be quantified. Additional characterisation parameters are also discussed. Different areas of application where ferrosilicon characterisation can be used are also discussed.CITATION:Bosman, J and Blair, W, 2017. The practical characterisation of ferrosilicon for dense medium applications, in Proceedings Iron Ore 2017, pp 135–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Natasha A. Essar

Nevsun Resources Ltd. Bisha Mine Project is a gold and base metal development project in the Gash Barka region of west-central Eritrea. The project has the potential to be one of the largest industrial developments in the country, and Eritreans have no experience in modern mining. Nevsun recognized early that the success of the Bisha Project would require meaningful consultation and engagement with all levels of Eritrean society. Meaningful engagement required not only full disclosure, but also capacity building from government officials at all levels to other stakeholders who live in the nearby communities. This paper describes the approach used to develop capacity and to help introduce a modern mining culture in a country without previous experience in mining.

May 1, 2007

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By Galen Bauer

"Up until the mid 1960's, the only available methods for making continuous weight measurements were through the use of mechanical and electro-mechanical weigh scales. It was during this time period that a new concept in weighing was introduced. It was known and is still known as the nuclear belt weigh scale.During the early days of its appearance in the market place, many things were learned about its advantages and disadvantages for weighing various materials. As with many new devices, it had to go through a ""wringing out stage"" before it became accepted by the weighing industry. Even today, even though it is a proven device, there are skeptics who believe the nuclear belt weigh scale will not survive. Let me assure you, it is here to stay.. 'PRINCIPLE OF MEASUREMENTThe nuclear belt weigh scale consists of a ""C"" Frame assembly which houses the radioactive source (Cesiwn 137) and the radiation detector (Ionization chamber). The ""C"" Frame assembly is put in place around the conveyor belt as shown in Figure 1. The radiation source emits a fan shaped beam of radiation which covers the full width of the material being conveyed on the belt. Radiation which has passed through the material on the belt is detected by the ionization chamber which is located in the lower arm of the ""C"" Frame assembly. The ionization chamber changes the radiation energy into an electrical signal which is related to pounds per foot belt loading. This signal is transmitted to a highly stable amplifier which combines the pounds per foot signal with a belt travel signal from a digital tachometer which allowed the scale user to be able to monitor total mass being conveyed. Many so-called conventional type scales use belt speed rather than travel to obtain mass per unit time, and then integrate the signal to obtain their weight signal. This unnecessary step tends to erode the overall accuracy of the weighing system."

Jan 1, 1975

By J. Matos e Silva

The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the Eurocode 7 recommendations. A comparison is also made with the behaviour of the diaphragm walls during the construction phase. From the referred examples the author presents his conclusions.

Jan 1, 2002

By Deborah Shields

Aggregate is an essential input to every economy, so governments need to ensure a sustainable supply of these resources through planning. There is also a need to shift from a linear economy to a more circular one, in which wastes are recycled rather than landfilled, so as to increase eco-efficiency. The purpose of the Sustainable Aggregates Planning in South East Europe (SNAP-SEE, SEE/D/0167/2.4/X) project is to develop a Toolbox for Aggregates Planning to assist governments and stakeholders in national, regional, primary and secondary, aggregates planning in southeast European countries. The Toolbox comprises documents on stakeholder consultation, data and analysis methodologies, a vision of best practices in aggregates planning and how to build an aggregates plan. The Toolbox will also support ongoing efforts to enhance minerals policy in the European Union (EU) as called for by the European Innovation Partnership on Raw Materials. Industrialized and developing nations see long-term and continued economic growth as essential to the well-being

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By Chee S. Theng

As the 2017 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2017 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 342. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2017 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH), a special review article on Heap Leach Modeling, and articles from two Special Issues on Rare Earths. The 2017 Transactions consists of a total of 54 technical papers, encompassing all 21 papers published in 2017 in the Technical Papers Section of Mining Engineering (Vol. 69) and all 24 papers published in 2017 in Minerals & Metallurgical Processing (Vol. 34). Additionally, this volume contains 9 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2017 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2017

By David Jurich, Joseph N. McDivitt

INTRODUCTION South Coast Water District (SCWD) operates the Beach Interceptor Sewer Tunnel(BIST) in South Laguna, Orange County, California between Monarch Beach and Aliso Beach (Figure 1). The 10,200-foot long BIST houses a 24-inch gravity Techite sewer pipeline critical to the SCWD Sanitary Sewer Collection System. The original tunnel and sewer pipeline were constructed in 1954 and the sewer line was replaced in 1974.Periodic inspections by sewer pipeline maintenance crews documented deterioration of specific intervals of the tunnel. Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline and a 731-foot section of tunnel located at Thousand Steps Beach was determined to be in immediate need of repairs. SCWD and consultants Hatch Mott MacDonald (HMM) and Tetra Tec prepared a Work Plan for emergency tunnel stabilization and pipe protection measures that was implemented in January 2007. Normal access to the beach and the section of tunnel requiring repairs was limited to public stairs referred to as Thousand Steps and, therefore, all materials and equipment needed for the work were transported to the beach by ocean-going landing craft. Additionally, the emergency repairs had to be completed without taking the pipeline out of service. Numerous environmental, logistical and operational requirements had to be overcome to complete the challenging emergency repairs. GEOLOGICAL SETTING The Laguna Beach area is located in the Peninsular Ranges of Southern California. The project area is located on the southwest flank of Niguel Hill along marine wave-cut cliffs and slopes. The tunnel was excavated in the San Onofre Formation, a marine deposit, characterized by abrupt lateral and vertical changes in lithologies that vary from boulder to cobble and gravel size breccias to medium coarse sandstones with gravel, sandy claystone and siltstone. The interval of the tunnel that required repairs is located within the San Onofre breccia, a moderately-to-well cemented, poorly bedded to massive unit with angular to subangular boulder and cobble sized clasts of schist. The sandy silt matrix of the breccia is composed of quartz, feldspar and schist grains (Figure 2). GENERAL TUNNEL DESCRIPTION The approximately 6-feet high by 6-feet wide 10,200-foot-long BIST was hand mined in 1954 at the base of the coastal cliffs. Primary access is through twenty-one access adits from public and private beaches. The tunnel is located in an easement that extends beneath private property with residential structures situated 50 to 80 feet above and horizontally in close proximity to the tunnel alignment. Most of the tunnel is horse-shoe shaped and unsupported, but approximately 3,000 feet is supported by timber

Jan 1, 2007

By Ian Misich

A research programme has been undertaken to evaluate and predict the effect of total extraction of coal by underground methods on the superimposed strata, aquifer systems and ground surface in the Collie Basin. Western Australia. The research work has integrated comprehensive field monitoring of surface and subsurface subsidence with empirical, analytical and physical modelling in an effort to develop an effective predictive tool which can be used in all mining scenarios. Early results indicate that although each method has certain limitations, this approach has enabled the researchers to develop a very good understanding of the subsidence mechanisms from the mine panel through to the surface in the weak, water saturated sediments in the Collie Basin. Given that both subsurface and surface subsidence characteristics have tied in well, greater confidence can be held for predictions made by representative models.

Jan 1, 1993

By John R. Freeman

THIS paper relates entirely to the casting of brass under fluid pressure in steel dies Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years The successful development of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitable die-casting machines The melting point of copper is 1084° C (1983° F ) and of a high brass about 900° C (1652° F ), as compared to 327 5° C (6215 °F) for lead, 419 4° C (786 7° F) for zinc and 658 7° C (1217 7° F) for aluminum, temperatures that ale indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals TYPE OF DIE-CASTING MACHINE In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy For alloys having the relatively high melting point of brass, this obviously is impossible Machines with a separate melting chamber are essential Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co , the latter developed by Zoseph Polak, of Prague, Czechoslovakia The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg 4

Jan 1, 1935

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for two longwall mining operations in the Northern Appalachian Coal Region. Vertical displacements and relative face positions are tabulated for 104 subsidence monuments. Brief physiographic and geological descriptions of the mining sites are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Jian Wu

In this paper, the surrounding rocks and the supports in a longwall are taken as an integral, i.e. a system. The structural characteristics and behavior of the system are discussed based on in-situ observations. A set of equations, which describe the interaction among the support, immediate roof and main roof, are developed. These equations can be used to design the longwall powered supports more reasonably and economically.

Jan 1, 1989

By B. Arlyuk

The complex system has been developed for long-term assessment of world prices and sale volume of primary aluminium when using the analytical model of the market and market supply forecasts as well as economy development in the Western countries characterized by the industrial production indices as correct data of Western World aluminium consumption are absent, The important part of this system is the model developed for forecasting the degree of capacities utilization of smelters and refineries depending on the price level, The model contains a statistic part corresponding to the capacities distribution by the production cost, and a dynamic part determining the deviation from the static depending on the price variation dynamics, The developed complex system has been identified by the actual data of the world prices of smelter grade alumina and primary aluminium, conservation and reactivation of refineries and smelters in the Western countries within the period from 1992 to 2003. The system was used for primary aluminium and alumina price forecasts till 2020.

Jan 1, 2004

By R. Burger, M. Masukawa

Cato Ridge Alloys (CRA) is a joint venture company between Assmang of South Africa, Mizushima Ferro Alloy Company (MZK) and Sumitomo Corporation from Japan. Negotiations for the formation of the company started in 1992 with the joint venture agreement signed on the 19th September 1996. MZK was to supply the technical know how for the production of Medium and Low Carbon FeMn while Assmang was to manage the day to day activities of the company. Sumitomo Corporation was to act as facilitator between Assmang and MZK and, together with Ore and Metal are responsible for the marketing of the refined products. The conceptual design of the plant started in December 1996 and the first charge of molten high carbon ferromanganese metal was charged on the 19th January 1998. Problems experienced during the initial startup period were addressed resulting in substantial operational improvements. A build-up in the stock of fine metal was addressed through the development of a process to remelt the fine metal, the development of a market for fine metal and the upgrading of the crushing and screening plant to reduce the generation of fine metal. The mass yield from High Carbon Ferromanganese to Refined Ferromanganese was increased through the implementation of statistical process control, changes to the blowing patterns and the development of a sampling device for taking samples during the process. Converter refractory consumption was reduced. This was achieved on the converter by improving the cooling of the converters with the installation of cooling fans and cooling fins. The heating schedule of the converters was changed for improved refractory life. Production schedules were modified to allow cooling of the refractory between low carbon erromanganese charges. Additional changes made to improve operations were: ? Changing from mehanite casting trays to metal fines beds. ? Installation of sonic horns in the baghouse to prevent the bridging of dust. ? Improved welding on the lance tips.

Jan 1, 2004