Search Documents

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?'The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.' "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

By Herty, C. H.

Three distinct processes take place during the conversion of iron ore to steel. First: the raw ore is reduced to metallic iron in the blast furnace and during this reduction certain constituents are dissolved in the iron, either through the solution of a solid into a liquid phase, as in the case of carbon, or by reduction of an oxide existing in the slag to the metallic element of that oxide, with subsequent solution of the metallic element in the iron. Thus by the process of solution and reduction, a pig iron results which contains about 4 per cent carbon, 1 per cent silicon, 1 to 2 per cent manganese, 0.1 to 0.4 per cent phosphorus, and 0.03 to 0.10 per cent sulfur. To obtain a sufficient yield of iron from the ore it is necessary that the reducing process be carried as far as possible, with the result that the impurities mentioned accompany the reduced iron. Second: to convert this iron into steel it is necessary to oxidize a part of the iron in eliminating the impurities to the extent desired for the particular product being made. In eliminating these impurities by oxidation a certain amount of iron oxide (FeO) dissolves in the steel. This dissolved FeO reacts with the metalloids, except sulfur, and to eliminate them to the desired extent it is necessary to leave a considerable amount of FeO in the metal. The reaction of iron oxide with silicon, manganese, and phosphorus results in the formation of the oxides of these elements. The oxides enter the slag and the extent of elimination of the elements depends on certain equilibria between the slag and the metal. The reaction of FeO with carbon results in the formation of the gases CO and CO, which, after saturating the metal, pass into the furnace gases. Third: after the iron has been purified to the desired extent as far as the elements listed are concerned, it is necessary to deoxidize the bath to remove the FeO, which is the vital factor in gas formation as the steel solidifies.

Jan 1, 1957

By Henri F. Letient

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid mine drainage and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings towards the end of the mine life, thereby generating a non-acid generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-acid generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid generating rock and to be flooded at the end of mine life.

May 1, 2002

By Qiang Guo, Zongliang Zuo, Mengqi Wei, Qingbo Yu, Qin Qin

Activated carbons, derived from waste ion-exchange resin by CO2 physical activation, were applied to separate CO2 from flue gas against global warming. The BET specific surface areas of activated carbons at different activation temperatures and times were investigated. The CO2 adsorption capacity was tested under non-isothermal and isothermal conditions. The experimental results show that when keeping the activation temperature constant, the specific surface area increases firstly and then decreases with increasing activation time. For the given activation time, the specific surface area rises firstly and then declines with increasing activation temperature. The adsorption capacity decreases with increasing temperature. The maximum adsorption capacity is 51.46 mg/g under the condition of 298 K and pure CO2. Fractional order kinetic model is the best one to describe the kinetics of CO2 adsorption. The activated carbons show the potential to be an effective adsorbent for the removal of CO2 from flue gas.

Mar 1, 2018

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

By S. Frimpong

Shovel excavation constitutes a significant component of production costs in any surface mining operation. This makes shovel loading an important cost center that needs to be improved to lower production costs. Optimization of tool design will improve energy efficiency in earthmoving operations. However, modeling the soil-tool interaction is a complex process due to the fact that forces for excavating particulate material are functions of many variables. The magnitude of this resisting force depends not only on the type of soil but on the size, shape and orientation of the cutting element. Moreover, part of this complexity is attributed to the fact that the behavior of the material during excavation is not yet well understood. For the past five decades, researchers have mostly used the passive earth pressure theory to study the soil failure patterns around a cutting tool and to develop force prediction models for design optimization with some success. Although the force models developed from the passive pressure theory have been successful to some extent, they can hardly be extended to a general case because of the underlying assumptions and simplification of tool shapes. This paper aims at reviewing some of the existing empirical and analytical methods of cutting and excavation tool modeling with a focus on their merits and limitations. The paper also explores the use of numerical methods, specifically the discrete element method, for dealing with the unresolved aspects of soil dynamics in excavation.

Jan 1, 2011

Pyrite Bioleaching and Slag Neutralisation - Two Treatments in a Single Process for Recovering Valuable Metals from Both Materials Very often the production of copper sulfide concentrate yields pyrite concentrate as a by-product. This is the case at the Knre mine in northern Turkey. This kind of concentrate may contain low grades of valuable non-ferrous metals. Bioleaching of such pyrite concentrates is a processing technique to solubilise metals like copper, zinc or cobalt in a sulfuric acid pregnant solution. The pyrometallurgical processing of copper sulfide concentrate produces slag that still contains valuable metals in varying concentrations. Slag is used in many ways: as aggregates, ballast, pavement material, in cement production and glass making. Due to its relatively alkaline nature, it can also be used to neutralise acidic solutions. A preliminary study of the bioleaching of the pyrite concentrate (Co 0.28 per cent, Cu 0.56 per cent and sulfur as sulfide 42.6 per cent) produced at Knre has been undertaken with the assessment of the neutralisation of the acidic bioleach solution by using old slag (Co 0.29 per cent, Cu 1.70 per cent and sulfur as sulfide 0.89 per cent) stockpiled on the site. The main conclusions of the study were as follows: Knre pyrite was amenable to bioleaching at 40¦C. Cobalt solubilisation directly related to pyrite degradation reached a maximum yield above 90 per cent. Final copper recovery was limited to approximately 66 per cent not directly related to bacterial growth and pyrite oxidation. Slag could be used as a substitute for limestone as a neutralising agent in the bioleaching tanks. Cobalt and copper could be recovered from pyrite concentrate and slag simultaneously from both materials. A pre-feasibility study is underway to carry out a preliminary cost estimate of an installation for cobalt and copper production from these two materials processed in a single operation.

Sep 13, 2010

By H. I. Kim

The leaching of a complex matte in chlorine and chloride media was studied. The matte was prepared from manganese nodules by the reduction smelting-sulfidation route. From XRD analysis, the major phases of the matte were identified as CuFeS2, CuS2, (FeNi)9S8, (FeNi)S2, Ni9S8, Ni3S2, (CoFeNi)9S8 and Co metal. Investigated were the chlorine, hydrochloric acid, hydrochloric acid-oxygen, ferric chloride, ferric chloride-oxygen, cupric chloride and cupric chloride-oxygen systems. The results are discussed in terms of reagent concentration, retention time, leach temperature and gas sparging rate. The chlorination process resulted >99% metal extraction efficiency within a short retention time and at atmospheric temperature. However, there were no preferential extractions of Cu, Ni and Co with respect to Fe. The cupric chloride-oxygen system produced leach liquors with the lowest Fe content and with a high base-metal extraction. Sulfide sulfur was converted to mixtures of elemental sulfur and sulfate in all the studied systems.

Jan 1, 2009

By Rclssell Gibson, F. S. Turneaure

The tin deposit of Monserrat; Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals.

Jan 1, 1950

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

A survey has been undertaken of the petrography of North Island greywackes with a particular focus on the occurrence in them of smectite (swelling clay) and chlorite, two minerals that are closely associated, chemically similar, and commonly interlayered with each other. Smectite is the mineral which is a major cause of greywacke aggregatesÆ poor performance. Smectite occurs in post-metamorphic shear zones and in surface weathering profiles over greywackes. This study focuses on the petrography of fresh greywacke rocks.   The occurrence and abundance of smectite and chlorite and their relationship in greywackes is largely a function of the chemistry of the sediment and the maximum temperature that the sediment has been subjected to during diagenesis and/or very low grade (anchizone) metamorphism. Rock chemistry, particularly total iron and MgO, determines the smectite and/or chlorite content in fine-grained greywackes (argillites and siltstones) but chemistry is less influential in sandstones, where at low grades of metamorphism much of the Fe and Mg of the rock is held in unreacted detrital minerals and the mineral constituents of lithic grains.   Four zones which represent different levels of diagenesis and very low grade metamorphism, based on the crystallinity of illite and chlorite in the greywackes, and the proportion of smectite interlayered with chlorite, have been mapped in the North Island. In the anchizone smectite does not appear as a discrete mineral, it is always interlayered with chlorite. In the upper anchizone chlorite contains approximately ten per cent of smectite interlayered with chlorite. In the lower anchizone about 30 per cent smectite can occur in chlorite.   In addition to the smectite and chlorite inherent in the greywackes as the result of the thermal overprint, smectite as a discrete mineral and smectite-chlorite interlayered minerals with high levels of smectite, occur in abundance on shear zone surfaces and in alteration zones adjacent to shear zones; these are the main contributers to the high levels of smectite recorded in many greywacke aggregates.

Jan 1, 2006

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability.The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employees to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed. IntroductionThis article is the second of three on predictive maintenance at the Louvicourt mine operated by Aur Resources Inc. The first article, published in the October 2002 issue, was about vibration analysis for rotating machines. This article describes how lubrication and oil analysis for stationary machines permitted Louvicourt to save more than $150,000 within two years and presents the evolution of the oil analysis program.Louvicourt mine, located near Val-d’Or, Quebec, is a copper and zinc mining and milling operation that processes 4300 t/d of ore and employs 289 people. Production began in 1994. Louvicourt mine is a partnership between Aur Ressources (30%), Teck Corp. (25%), and Novicourt (45%)."

Jan 1, 2003

By J. C. Duchon

The use of extended workdays or compressed workweeks (regular shift lengths exceeding 8 h) is attracting growing interest in many industries using continuous operations. While extended workdays promise increased worker satisfaction due to more days off, including weekends and holidays, there are legitimate concerns about the potential effects on the health and safety of such a schedule. The U.S. Bureau of Mines (USBM) conducted a study at a Canadian underground copper, lead, and zinc mining operation that was designed to study the safety and performance implications of extended workdays. Measures were taken before and after a change from the old 8-h continuous schedule to the new 12-h continuous schedule, including behavioral performance measures to analyze perceptual-motor changes, continuous heart-rate monitoring and aerobic capacity to measure physical fatigue, a variety of self-report questionnaires to measure perceived adaption and satisfaction with the new schedule, and pulmonary-respiratory measures to examine air contaminant exposure. Based upon the overall acceptance of the new schedule by the workers and lack of change in fatigue-sensitive behavioral and physiological performance measures, this study recommends that the mine retain the 12-h schedule. However, certain precautionary measures are suggested to insure the safety of the workers.

Jan 1, 2010

By W J. Rankin

A study was carried out to compare the environmental impacts of a number of process routes for lead and zinc metal production from sulphide ores using Life Cycle Assessment methodology and based on average industry data derived from the literature. The processes investigated were:blast furnace production of lead; Imperial Smelting Process for lead and zinc production; and electrowinning of zinc with the mining and mineral processing stages common to all three routes. The effect of a number of process variables, namely ore grade, fuel source for electricity generation and efficiency of generation, on the environmental impacts was also examined. The environmental impact categories considered in the study were:total (or full cycle) energy consumption; Global Warming Potential (GWP); and Acidification Potential (AP). The results of the study show that when produced separately, zinc production is more than twice as energy intensive as lead production (viz 48 and 20 MJ/kg respectively), however when produced jointly by the Imperial Smelting process, the energy intensity of the two metals is not all that dissimilar (viz 36 and 32 MJ/kg respectively). The metal production and refining stage was found to make the greatest contribution to the overall environmental impacts for all three processes. The study also highlighted the importance of taking a life cycle approach when comparing the environmental impacts of different processes.

Jan 1, 2002

By Henrique Dias Gatti Turrer

Atividades de pesquisa e desenvolvimento (P&D) possuem efeito positivo nos indicadores econômico-financeiros das organizações. Essas atividades possuem características de projetos, e, por isso, podem ser submetidas aos processos de gerenciamento recomendados pelo PMBOK. As atividades da gerência de P&D do Minas-Rio da Anglo American foram submetidas à alguns desses processos. Inicialmente, foram estratificados os processos por magnitude de esforço e de impacto. Oito processos foram classificados como de baixo esforço e alto impacto e, por isso, totalmente implementados. A criação e aplicação de três ativos organizacionais padronizados para todas as atividades realizadas permitiu o desenvolvimento de grande parte dos processos considerados mais importantes. Um questionário de avaliação do grau de maturidade em gerenciamento de projetos foi respondido por parte da equipe antes e depois da adoção formal de tais processos. O grau de maturidade aumentou significativamente, 150%, em dois anos, passando do nível conceitual para padronizado. Além disso, foi observada um aumento significativo, igual a 731%, no número de atividades realizadas pela área.

Oct 30, 2017

By Huimin Lu, Zegao Sun, Zhijiang Gao

The traditional Ti6Al4V alloys were obtained by the smelting reduction of V-Ti bearing beach placer by rotary hearth furnace and aluminothermic reaction in laboratory. First, it gets he lp from combined rotary hearth furnace and grinding magnetic separation process to prepare titanium slag containing vanadium. In this study, a neural network model was used. The comparisons between experiment results and neural network simulation results show that genetic algorithm (GA)-based on back propagation (BP) method can predict the degree of reduction and separation of iron and slag with higher prediction accuracy. Then by aluminothermic reaction process, the optimized process parameters for Ti-V-Al alloys were searched. Al can deoxidize metal V and Ti from the metal oxides of artificial rutile containing vanadium. Finally, traditional Ti6Al4V alloy can be obtained by remelt and adjust the constituents.

Jan 1, 2016

By S. L. Windes

This report presents physical and petrographic properties of approximately 60 types of rock from operating mines or mineral-investigation projects and supplements Repot of Investigations 4459, Physical Properties of Mine Rock (hereinafter referred to as Part I). The physical properties evaluated include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength (modulus of rupture) Impact touchiness Abrasion hardness Scleroscope hardness Modulus of elasticity (Yourg?s modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1950

By P. Ret, E. Üstiindag, R. Dieckmann, R. Subramanian, S. L. Sass

"Partial reduction reactions in the Ni-AI-O system, starting with the spinel compound NiAI20 4, are used to form metal-ceramic microstructures. By suitable choice of processing parameters, such as reduction temperature, oxygen partial pressure and time, two different morphologies of nearly pure Ni particles, equiaxed and rod-like, form within a ceramic matrix, which is either a-A12O3 or a metastable ""defect spinel"". Electron microscopy studies were performed for microstructural characterization, phase identification and chemical analysis. The fracture toughness of the Ni-AI2O 3 mixture was significantly improved with respect to that of the original spinel phase. The important issues that must be addressed to form useful metal-ceramic microstructures by partial reduction reactions rue discussed. It is shown that cracking at the original spinel grain boundaries, likely due to the large volume changes associated with the reduction reaction, can be avoided by the addition of small amounts of ZrO2• Initial results illustrating effect of ZrO2 on the microsuuctures are presented.IntroductionEngineering materials used in load bearing circumstances, particularly under extreme conditions (e.g. high temperatures or stresses), generally are formulated with complex microsuuctures. Such composite-like materials can possess properties unobtainable by either of the individual constituents. With metal-ceramic composites, for example, a material can be obtained with an optimum combination of the low density and high strength of the ceramic, and the toughness of the metal. For high temperature service, where demanding conditions are often present, for example, inside jet turbine engines, a successful new material must have low density, high Young's modulus as well as good oxidation resistance, strength, fracture toughness, creep and fatigue resistance. The candidates include intermetallic compounds, and metal-ceramic, intermetallic-ceramic and ceramic-ceramic composites."

Jan 1, 1994

Council for 2001/2002 President A.A.B. Douglas President-elect S.J. Ramokgopa Vice-presidents Senior F.M.G. Egerton Junior Prof. T.R. Stacey Immediate Past-president Dr L.A. Cramer Honorary Treasurer J.A. Cruise

Jan 1, 2002

By O. Gunaydin

Performance measurements of large-diameter circular saws were conducted on eight different carbonate rocks in marble factories located in some areas of Turkey. Rock samples were collected from these factories for laboratory tests. Uniaxial compressive strength, tensile strength and impact strength were determined in the laboratory. The brittleness of B3 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), the brittleness of B5 (the product of percentage fines in the impact strength test and compressive strength) and the brittleness of B8 (half of the product of compressive strength and tensile strength) were calculated from the test results. Hourly slab productions were correlated with brittleness indexes. It was concluded that sawability of carbonate rocks can best be predicted from the brittleness of B8.

Jan 1, 2004