Search Documents

By R. G. Turner, M. G. Hubbard, A. E. Dukler

Gas phase hydrocarbons produced from underground reservoirs will, in many instances, have liquid phase material associated with them, the presence of which can affect the flowing characteristics of the well. Liquids can come from condensation of hydrocarbon gas (condensate) or from interstitial water in the reservoir matrix. In either case, the higher density liquid phase, being essentially discontinuous, must be transported to the surface by the gas. In the event the gas phase does not provide sufficient transport energy to lift the liquids out of the well, the liquids will accumulate in the wellbore. The accumulation of the liquid will impose an additional back pressure on the formation that can significantly affect the production capacity of the well. In low pressure wells the liquid may completely kill the well; and in the higher pressure wells there can occur a variable degree of slugging or churning of the liquids, which can affect calculations used in routine well tests. Specifically, the calculated bottom-hole pressures used in multirate backpressure tests will be erroneous if the well is not removing liquids on a continuous basis, and gas:liquid ratios observed during such a test may not be correct. Several authors1,3,8,14 have suggested methods to determine if the flow rate of a well is sufficient to remove liquid phase material. Vitter14 and Duggan' proposed that wellhead velocities observed in the field would be adequate for keeping wells unloaded. Jones8 and Dukler3 presented analytical treatments resulting in equations for calculating, from physical properties, the minimum necessary flow rate. An analysis of these studies indicates the existence of two proposed physical models for the removal of gas well liquids: (1) liquid film movement along the walls of the pipe and (2) liquid droplets entrained in the high velocity gas core. Although there probably is a continuous exchange of liquid between the gas core and the film, they will be treated separately for the purposes of this study. The development and comparison of these separate models with experimental data will permit the determination of which, if either, is the controlling mechanism for the removal of liquids from gas wells. The Continuous Film Model Liquid phase accumulation on the walls of a conduit during two-phase gas/liquid flow is inevitable due to the impingement of entrained liquid drops and the condensation of vapors. The movement of the liquid on the wall is therefore of interest in the analysis of liquid removal from gas wells. If the annular liquid film must be moved upward along the walls in order to keep a gas well from loading up, then the minimum gas flow rate necessary to accomplish this is of primary interest. The analysis technique used follows Dukler2 and Hewitt5 and involves describing the profile of the velocity of a liquid film moving upward on the inside of a tube. The minimum rate of gas flow required to move the film upward is then calculated.

Jan 1, 1970

By H Mischo, G Barakos, J Gutzmer

The continuously growing demand for rare earth elements (REEs), in combination with the crisis of 2009 and the price spike of 2011, has initiated a treasure hunt for rare earth deposits all over the world in recent years. Since then, commodity prices have declined and are now quite stable, yet the world is still dependent on China’s dominance of the market and its export policies. Exploration is unremitting and numerous resources of potential interest have already been revealed in many countries; however, proceeding to mining operations is not that simple, especially when it comes to the exploitation of rare earth deposits. Evaluating the feasibility of a mining project is always a unique, sensitive and rather complex process that depends on multiple criteria.This paper focuses on clarifying the present and future global situation in the development of respective deposits and on identifying rare earth-specific criteria that influence the overall feasibility assessments of any potential (especially underground) mining projects. Environmental impacts, legislation issues and the presence of radioactive pollutants are some of the notable boundary conditions that govern rare earth mining operations and need to be taken into consideration. Furthermore, the balance problem between the supply and demand of the different REEs can determine decisively whether a deposit of specific REEs is economically exploitable. For this reason, evaluations are made regarding the future strategies to be enacted in order for the rest of the world to detach itself from this situation. The ultimate goal of these evaluations is for them to be incorporated in an overall assessment tool for rare earth underground mining procedures that will be implemented in real case studies to determine their sustainability.CITATION:Barakos, G, Mischo, H and Gutzmer, J, 2015. Status quo and future evaluations of global rare earth mining (with respect to special rare earth element-industry criteria), in Proceedings Third International Future Mining Conference, pp 21–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By S. Johnson

Introduction The mining of aggregates underground has grown steadily over the last 25 years. Growth has come in both production volume and in the importance this segment of the industry is playing in the continuing supply of construction aggregate. Underground aggregate mines will continue to grow in both number of operations and complexity, as the replacement of zoned reserves in metropolitan areas becomes crucial. This growth will result in a shortage of qualified mine managers, possibly limiting the success of these facilities. The aggregate industry will have to modify current practices in order to meet the growing demand for this specialized skill. Segment Growth Underground mining for aggregates is not a new idea. Martin Marietta has been operating underground mines since 1969, and currently operates 16 underground mines ranging in size from 250,000 tpy to 2,500,000 tpy. These mines represent less than 4% of the total number of operating locations, but contributed 9% of the annual production in 2004. Though they range in size and production capacity, the importance is evident. The 2000 United States Census revealed several trends that are of interest to the aggregate mining industry. For the period 1990-2000 the U.S. population grew by 33 million or 13%. There were nine major metropolitan areas with a population of five million or more. These nine areas accounted for 30% of the total U.S. population. More significant was the fact that the population growth in these nine metro areas was 25% of the growth for the entire country. These statistics tell us that the population is expanding in these major metropolitan areas at a staggering rate. The same thing is happening to some degree in every population center. Population growth increases the demand for local aggregate while reducing the available area to mine that aggregate. The need for an economical supply of aggregate to support community expansion is a problem that will grow as older quarries are mined out and closed. This will be an issue that communities of all sizes will have to deal with. A reliable and cost effective supply of quality aggregate is crucial to support community expansion.

Jan 1, 2006

By Robert S. Hedin

Passive methods of treating mine water use chemical and biological processes that decrease metal concentrations and neutralize acidity. Compared with conventional chemical treatment, passive methods generally require more land area, but use less costly reagents and require less operational attention and maintenance. Currently, three types of passive technologies exist: aerobic wetlands, organic substrate wetlands, and anoxic limestone drains. Aerobic wetlands promote mixed oxidation and hydrolysis reactions, and are most effective when the raw mine water is net alkaline. Organic substrate wetlands promote anaerobic bacterial activity that results in the precipitation of metal sulfides and the generation of bicarbonate alkalinity. Anoxic limestone drains generate bicarbonate alkalinity and can be useful for the pretreatment of mine water before it flows into a wetland. Rates of metal and acidity removal for passive systems have been developed empirically by the U.S. Bureau of Mines. Aerobic wetlands remove Fe and Mn from alkaline water at rates of 10-20 and 0.5- 1.0 g. m-2? d-1, respectively. Wetlands with a composted organic substrate remove acidity from mine water at rates of 3-9 g. m-2? d-1?. A model for the design and sizing of passive treatment systems is presented in this report.

Jan 1, 1994

By Eldon Keith Stanek

This annual report deals with four distinct tasks related to research on the safety and reliability of mine electrical power systems. Task one is to develop tests and the associated instrumentation to detect incipient faults on a mine or any low-voltage power system. Task two is a dual effort related to the digital prediction of electrical transients on mine power systems and laboratory testing of transient suppression devices. Task three is also a dual effort. This task consists of both theoretical and laboratory work to assess both the reliability and the fail-safe characteristics of several items of protective equipment used in mine power systems. Task four consists of an effort to use programmable calculators and/or computer terminals to check overcurrent protective device coordination.

Jan 1, 1976

By Associates

The headwaters of Skippers Creek and the Shotover River are reputed to be among the richest alluvial gold catchments in the world. This alluvial gold has no doubt been derived from reef systems similar to, and associated with, the Bullendale lodes. Physiographically the prospect covers steep ridges and deeply incised gullies between the Richardson Mountains in the west and the Harris Mountains in the east. Vegetation is mainly tussock with bush either side of Murdochs Creek. Access to the area is by metalled road to Skippers and then by 4WD track to Bullendale. Alternatively the prospect area can be reached by helicopter from Queenstown in around ten minutes.

Jan 1, 1992

By H Peiming, W Sakurai, Y Matsuhisa, H Shimazaki, Y Fukahori

Oxygen and carbon isotope mapping of hydrothermally altered wall rocks was applied to the blind ore prospecting of skarn Pb-Zn deposits in the Kamioka mining district, centralJapan, where the wall rocks consist of heterogeneous rock units. The results (d18OSMOW of -1.1 to +17.3ë and d13CPDB of -5.0 to +4.8ë for limestones, and d18OSMOW of -0.8 to +12.5ë for silicate rocks) show isotope zonations of the wall rocks with depletions in heavy isotopes (18O and 13C) toward the centre of mineralization. The isotope zonations likely formed by interaction of migrating thermal waters with the wall rocks during the mineralisation. The heavy-isotope depleted zone, which indicates higher temperature or higher water-to-rock ratio of the system, occurs in the footwall of a fault, indicating that the fault played the role of main conduit of the ore-forming fluids. A heavy-isotope depleted zone was also found in an area, where significant mineralisation had yet to be identified. Recent drilling in this area has intercepted a zone with a grade of 16.0% Zn, 0.8% Pb, and 35g Ag per metric tonne at a depth of about 360 m.

Jan 1, 1995

By J M. Parr, P M. Herzig, J B. Gemmell, S D. Scott

PACMANUS is an actively-forming seafloor analogue of volcanic-hosted massive sulfide orebodies, situated on the crest of an andesite-dacite-rhyodacite ridge overlying rifted older arc crust in a back-arc basin. Hydrothermal deposits range from Mn-oxide crusts to Cu-Zn-rich massive sulfide mounds and chimneys containing significant Au and Ag. Preliminary data suggest a substantial magmatic component to fluids and metal sources, and we speculate that PACMANUS is the cap to a complete hydrothermal system including subvolcanic and intrusive-related mineralisation.

Jan 1, 1995

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984

By S. Dessureault, Z. Gavelan

As globalization continues, sustainability and social responsibility has become essential in foreign mining investment. However this global trend and the increasing acceptability toward the globalization process, viability and sustainability are not always achieved. Viability and sustainability of mineral projects is dependant on the social and political environment of the region where the mining venture is located and is based on the interaction between the mining entrepreneurs, national-local government representatives, communities, grass-roots groups and independent civil organizations. These are the organizations, which play the acting roles on the viability of mining projects and are the main source of socio-political risks for the project. Throughout the decision-making process to invest in a mineral project, socio-political risks are quantified using a set of measurable variables. Nevertheless, these risk measures should be dependent on specific industries. Two mineral projects, even in the same mining district, may have significantly different political risk profiles based on their own socio-political variables. This paper describes a methodology that takes into account local social and political variables in defining a project-specific’s political risk profile. This contrasts with more typical political risk measures that focus on the country’s overall risk profile. Mining operations must operate on a local scale necessitating the development measure that considers more local variables.

Jan 1, 2004

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By Michel Aubertin

Les haldes à stériles contenant des minéraux sulfureux réactifs constituent un milieu favorable à la production du drainage minier acide (DMA). Au sein de ces haldes, les processus physiques, géochimiques et biologiques qui mènent à la production du DMA sont nombreux et complexes. Un des aspects critiques qui affecte la génération de DMA est la distribution et le mouvement de l?eau dans les roches stériles. La modélisation numérique est un outil qui permet de comprendre, pour éventuellement contrôler, les mouvements de l?eau (et donc réduire la production du DMA) dans les haldes pendant la période d?exploitation de la mine et à sa fermeture. Plusieurs simulations numériques des écoulements non saturés dans des haldes ont été effectuées. Pour ces simulations, on a considéré divers types de matériaux, diverses conditions atmosphériques et diverses configurations géométriques. Les simulations réalisées montrent que l?on peut contrôler les mouvements de l?eau en introduisant des couches de matériaux fins intercalées dans les haldes formées de matériaux grossiers. Des couches horizontales ne sont cependant pas appropriées puisqu?elles peuvent, dans certains cas, favoriser la création de zones humides susceptibles d?amplifier les effets du DMA. Une faible inclinaison des couches de matériaux fins vers l?extérieur permet de palier à ce problème. Les couches inclinées favorisent un drainage des haldes vers la périphérie. Ceci a pour effet de garder sèche une grande partie des stériles et de réduire, par le fait même, la production du DMA.

Nov 1, 2002

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

How to Evaluate Crushed Rocks for Concrete Production

Sep 13, 2010

By M. F. Handley

Sequential grid mining has been employed as the primary mining strategy at the AngloGold West Wits Elandsrand Mine since the inception of stoping operations from the sub-vertical shaft system in 1988. Little has been published on sequential grid mining as a mining strategy since, and the purpose of this paper is to describe sequential grid mining, its history, its implementation at Elandsrand, and the outcome to date. The results obtained using sequential grid mining have been evaluated from seismic data, productivity statistics, and rock related accident statistics. Comparisons with neighbouring mines namely Western Deep Levels and Deelkraal, have been made to substantiate the improved conditions observed at Elandsrand, and to compare sequential grid mining directly with longwall mining in similar conditions and at similar depths. Sequential grid mMining is shown to be cost-effective, more flexible, and safer than long wall mining in similar conditions, at least on the Ventersdorp Contact Reef in the western part of the Carletonville Goldfield. More work is necessary to establish it as the favoured mining strategy at depths exceeding 3000 metres, and for reefs other than the Ventersdorp Contact Reef.

Jan 1, 2000

By D Craw

TheSouthern Alps in the South Island of New Zealand are currently rising rapidly as a consequence of continental collision along the Pacific-Australian plate boundary. Rapid uplift has resulted in a major thermal anomaly in the shallow crust beneath the alps. Alpine topography and associated intense precipitation, coupled with the thermal anomaly are responsible for vigorous combined topographic/convective circulation of water through the shallow crust.   Uplift is greatest in a wedge-shaped region between the Alpine Fault and an associated second-order backthrust system, the Main Divide Fault Zone, approximately 20 km to the east. The Main Divide Fault Zone is segmented into NNE and NE striking faults, which are regionally sub-parallel to the Alpine Fault, but dip northwest in the opposite direction. Reverse oblique-slip on the Main Divide Fault is in an easterly direction, with a greater component of strike-slip movement on the NE trending faults. Elevated topography in the Mt Cook region is related to thrusting of a relatively homoclinal sequence of semi-schistose rocks on top of lower-grade greywacke, which controls the position of the Main Divide. Tectonically induced fluid flow resulted in only minor alteration and hydrothermal mineralisation of fault-rocks in Alpine and Main Divide Faults, and localised deposition of quartz and/or carbonate in the immediate hangingwall.   The wedge between the Alpine and Main Divide Faults is segmented by third-order structures north of the Mount Cook region. A series of right-lateral (-085/700S) and left-lateral (-150/600SW) faults, which are synthetic and antithetic to the Alpine Fault, respectively, developed as a conjugate set during uplift. Fluid-flow in the Southern Alps is controlled by these third-order fault/fracture systems. Cu-Au mineralisation, hydrothermal veins, and surface hot spring activity are localised by third-order fault/fractures and appears to be enhanced where conjugates intersect.

Jan 1, 1995

By James W. Hendrix

A survey of endomycorrhizal fungi occurring on orphan coalmine lands in Western and Eastern Kentucky revealed a great diversity of species present. Thus a large number of fungi are available for isolation and evalution for enhancing revegetation of mined land. Endomycorrhizal fungi isolated from orphan mines stimulated growth of sweetgum seedlings on mine soil at low fertilisation but inhibited growth at high fertilization; this growth inhibition at high fertilization did not occur with plants growing on peat-perlite. Banding of endomycorrbizal inoculum was not advantageous, compared with incorporation of inoculum throughout the growth medium, for production of mycorrhizal sweetgum seedlings. Newly reclaimed mine spoils were nearly nonmycorrhizal, compared with land reclaimed four or eight years earlier. A procedure for isolation of single-spore cultures of endomycorrhizal fungi was developed; this procedure is necessary for studies of ecotypic variability. A practical procedure using container-grown Pisolithus tinctorius-infected shortleaf pine seedlings for production of large numbers of bareroot pine seedlings infected with P. tinctorius for mined land reclamation was demonstrated.

Jan 1, 1982

By Clayton M. Rumsey

The U.S. Bureau of Mines conducted a mineral resource survey of the Cinder Cones Wilderness Study Area (WSA) (CDCA-239), 10 miles east of Baker, CA, in 1983. The 44,299-acre WSA is underlain by Precambrian granite gneiss, Upper Cretaceous or lower Tertiary Teutonia quartz monzonite, and Quaternary basalt flows and alluvium. This mineral survey included an examination of two volcanic cinder mines, five lode prospects, two volcanic cinder prospects, and reconnaissance sampling in and near the WSA. The seven prospects are in the WSA; the two volcanic cinder mines are adjacent. No mines are in the WSA. In 1981, there were 61 placer and 3 lode mining claims in the WSA. Sample results from two prospects within the WSA contained significant gold and silver values; however, the mineralized rock is of limited extent and no resources were apparent. Alluvial samples taken throughout the WSA contained only traces of gold. Two volcanic cinder cones within the WSA contain an estimated 30 million tons of cinders. There are sufficient cinders outside the WSA to satisfy demand in the foreseeable future. Stone, sand, and gravel deposits are not resources because similar material is closer to markets. No evidence of energy minerals or geothermal resources was found.

Jan 1, 1985

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001