Search Documents

The following paper outlines the types of employment immediately available to graduates following their university degree, a discussion on mine manager requirements, mentions career advancement and time frames to achieve this as well as providing some key information regarding student vacation work. The author hopes to educate present graduates, as well as inform students of characteristics to develop the most opportunities in life.

Jan 1, 2006

By Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory are developing a borehole profilometer to dynamically measure the roughness pro-file of boreholes used to install roof bolts fully encapsulated with resin. Numerical measures of roughness were calculated from profiles of borehole surface roughness to determine potential roof bolt anchorage capacity. The concept of dynamically profiling was proven through the following series of laboratory tests: a sensitiv-ity test using various grits of sandpaper, a known-profile test along a section of a concrete hole, and a simulated borehole test in a pipe with machined grooves. Two profilometer prototypes were devel-oped that measure slight changes in the radius of a borehole using either strain-gauged, spring-steel arms or rigid, steel arms attached to a spring-loaded cone and a linear potentiometer. Both instruments performed reasonably well in the laboratory and were subsequently tested in boreholes drilled in two concrete blocks using different drilling techniques to obtain three different borehole surface roughnesses. A Z2 roughness parameter was calculated with data from the first profilometer, and an average radial increment was calculated from the test results of the second profilometer. Although both instruments were able to readily distinguish the difference between smooth and rough boreholes, the correlation coefficient (r2) for a linear relationship between Z2 and average radial increment was 0.577. Pull tests were conducted with resin bolts installed in the concrete blocks, but maximum pull-out strength could not be correlated to borehole roughness because in each of these tests, failure occurred at the resin-bolt interface. A more sophisticated prototype has been designed to measure surface roughness and also accurately determine the location and tilt of the instrument in the borehole. However, this instrument has not yet been fabricated or tested.

Jan 1, 2007

By Hans Lundberg

GEOPHYSICAL methods as described in technical articles generally fail to answer the questions of prospectors and geologists as to which method they should apply and what information they may expect from their application. This article is an attempt to discuss the use of electrical methods with special reference to the prospecting for orebodies and the map¬ping of geologic structure. Especially on virgin ground, geological reconnaissance should precede electrical prospecting, with the object of outlining carefully the orebearing rock and determining the possibilities of elec¬trical prospecting. No electrical survey will then be carried out on ground which, for geological reasons, may be considered barren or where the electrical meth¬ods are inapplicable. As the success of electrical prospecting depends on the difference in conductivity between the ore and the country rock within which the orebody is inclosed, the conductivity of the two should be considered and de¬termined, if possible. The conductivity of an orebody depends on the distribution of conductive ore minerals and, in addition, on its size (length, width and depth). Most minerals with metallic luster show good electrical conductivity; for instance, the sulfides. Zinc-blende is an exception, but as it is often associated with the ore minerals of good conductivity (for instance, pyrite or galena), there is likelihood also of finding zinc.

Jan 1, 1930

By K. Hopperstead

Ventilation planning in trackless metal mining is often taken for granted. This paper highlights the trials of planning and executing the ventilation design for Bog Zone at the Lisheen Mine. Ventilation planning for Bog Zone started at the feasibility study stage in 2003; subsequent design changes continued until 2006. In August 2006, the development of the Bog Zone ore body was accelerated through the use of contractors; in addition, the Lisheen equipment fleet was revised based on a larger load and haul fleet. As a result, the circuit was reviewed in terms of changes in design conditions and best practices. This review resulted in a 40% increase of total airflow required to mine Bog Zone. Resources utilized to design the circuit include: external review, computer modeling, and in-house Lisheen planning and operational staff review. The final ventilation design configuration was adopted in 2007, after modeling and evaluating 30 different scenarios, resulting in a better distribution of airflow, optimized secondary escape way, reduced contaminants, and a total power reduction. The value of investment in computer modeling of primary ventilation circuit and planning for staged implementation should never be underestimated.

Jan 1, 2009

By Michael Schmitz, John A. Organiscak

ABSTRACT: A method (patent pending) has been developed to determine the quality of environmental cab filtration systems. This method utilizes specially configured filter cartridges to remove carbon dioxide from the ambient air with the environmental cab’s air filtration system. A real-time gas monitor is placed inside an unoccupied cab with the filtration system running to time decay the carbon dioxide to its lowest concentration or equilibrium level. The outside carbon dioxide concentration level can be measured concurrently with another gas monitor or with the same inside cab gas monitor during a representative period before and after the inside sampling is conducted. Cab filtration system leakage is comparatively deduced from the difference between the special cartridge filter efficiency and overall cab efficiency. Laboratory trials have illustrated that desirable high efficiency test filter configurations (greater than 99 % efficiency) can be devised, but have air quantity and test time limitations. These trials also demonstrated that CO2 penetration was reflective of controlled air leaks around a high efficiency filter under equilibrium conditions. This report examines the elements of this patent pending method.

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By L. E. Cardwell

This publication contains routine analyses and related source data for 377 natural gas samples from 19 States and two foreign countries. Of this total, 373 samples were collected during calendar year 1970. The remaining four samples were collected during previous years, but releases granting per-mission to publish the analyses were not received until 1970. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Twelve previous publications have presented the results of 9,050 gas analyses prior to 1970. The first three, Bulletins 486,6 576,8 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1971

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By J. C. Bayles

Jan 1, 1886

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By Max L. Glenn

As part of its goal to minimize requirements for mineral commodities through conservation and substitution, the Bureau of Mines conducted research to develop molybdenum as a potential substitute for superalloys containing the strategic and critical materials, nickel, chromium, and cobalt. Since molybdenum requires protection from oxidation at high temperatures, several complex oxides of the spinel and perovskite structure were investigated to determine which possessed the greatest potential for use as oxidation-barrier coatings. Two spinels (MgCr204 and MgA1204) and five perovskites (BaHfO3, YCrO3, NdCrO3, BaZrO3, and LaCrO3) were selected for testing. Various high-temperature prop¬erties that are important for oxidation-resistant coatings were examined, including diffusion rates of oxygen and molybdenum, recession (vaporization) rates, hardness, erosion resistance, sinterability, reactivity with molybdenum, and ease of application. From the evaluation of high-temperature properties, two spinels (MgCr204 and MgA1204) stand above the other oxides as possible coatings for molybdenum. However, laboratory coatings of MgCr204 at 1,360° C (2,480° F) are equivalent or inferior to currently available MoSi2 coatings; laboratory coatings of MgA1204 may be comparable under limited conditions to currently available MoSi2 coatings at the same temperature.

Jan 1, 1979

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By John E. Rourke, O&apos

This report documents the process of site selection, instrument installation, data acquisition, and preliminary data analysis followed to characterize the physical response of overlying strata to longwall mining. A system of surface, subsurface and mine level instrumentation was installed at the Allen Mine in Weston, Colorado where the overburden varied in thickness from 600 to 900 feet. Survey monuments, automatic-recording strain-meters, multi-point rod extensometers, inclinometer-extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. A preliminary analysis of the data acquired up until project termination has shown the system to be operative and strata response to be similar to that reported for other subsidence monitoring case histories. Recommendations for continued monitoring of the instrumentation systems are presented.

Jan 1, 1982

By AIME AIME

THE first fall meeting of the new Coal Division started on time on Thursday morning, Sept. 11, at Pittsburgh, with Paul Sterling of the Anthracite Section presiding and over a hundred members and guests in the room. The attendance increased from session to session, the total registration being 248. Excellent arrangements had been made by the officers of the Division covering all features of the meeting, the only drawback being that more papers-were listed for presentation than could be discussed in the time available. Howard-N. Evensong, chairman of the Division, explained this situation as sore and sore papers case in by likening it to the case of the small boy who wanted a second niece of pie at the end of a large seal. When his mother remonstrated that if he ate any more he would certainly burst, the young man replied, "Well, you just hand over the pie and then get out of the way." With that Mr. Evensong turned the meeting over to Mr. Sterling, who handled it so well that with ample discussion it was still possible to adjourn at lunch time, all but the group of junior papers having been heard. This series of papers, the output of the .very lively Junior Section organized last spring by the younger men of the Division was regretfully put over until Friday morning, when that on "Heat Drying" by S.. M. Parsley was read.

Jan 1, 1930

The contiguous Kotre Basantpur and Pachmo (KBP) coal blocks in the Hazaribagh District of Jharkhand State in east India are being developed by Tata Steel Limited (Tata Steel) to supply coking coal to a new steel mill at Kalinganagar in Orissa.The planning challenges are many. The multiple coal seams range in thickness up to 6 m and extend to nearly 500 m depth, with dips up to 25¦ and highly variable quality. Several normal faults with throws up to 150 m intersect the deposit. There is little room for waste dumping on the lease, several large nalas (seasonal creeks) cross the blocks, and the KBP leases are not contiguous with Tata Steel's existing mining operations at West Bokaro. Geotechnical conditions, while not well defined at this stage, are largely unfavourable. There are several villages on the blocks, and extensive paddy fields. In 2009, Adelaide Mining Consultants Pty Ltd (AMC) completed a Detailed Project Report (DPR) for a production level of 8 Mt/a. A terrace mining system was proposed using 28 m3 hydraulic excavators and 185 t trucks working horizontal up-dip slices. Subsequently the viability of in-pit crushing and conveying was assessed, but the full results were not available for this paper.It is planned to extract a total of 147 Mt of raw coal at a strip ratio of 5.2 bank cubic metres per tonne (bcm/t). The planned maximum pit depth is over 300 m.The project includes a washery, a 2 + 25 MW fluidised bed power station to utilise all the coarse washery rejects, and a railway spur line to carry the washed coal to the railhead some 7 km distant.

Dec 6, 2010

By John Lindsay

Outline ??Recovery plant requirements and concepts ??Common recovery plant unit processes ??Recovery plant design considerations ??Peripheral issues Process Design ??Liberation ??Separation ??Recovery Processing ??Density 3.5 g/cm3 ??Luminescent under x-ray ??Hydrophobic (non wettable) surface ??Non-magnetic ??Inert to strong acids / bases

Apr 1, 2005

By A. T. Iannacchione

Underground limestone mines typically use the room-and-pillar method of mining in the generally flat-lying limestone formations. In some cases the dip may exceed 5° which can result in unique roof instability problems. Stability may be further exacerbated by the presence of horizontal tectonic stresses. Field studies and numerical model analyses are combined to assess the affect of the dip in various stress conditions. The results showed that where the horizontal tectonic stresses are sufficient to cause intact rock failure, increasing dip results in increased failure potential. The effect of the dip is greater when the maximum horizontal stress is parallel to the dip. Two case studies are presented and evaluated against the findings of stress analysis results. The study showed that the empirical rules of orienting headings parallel to the maximum stress are generally applicable to dipping excavations, except when mining in the up-dip direction. The importance of accurately determining the orientation of the maximum horizontal stress is emphasized because the window of favorable orientations relative to the stress is small.

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967

By Xu Ronglie

This paper looks back on the developments and achievements of deep foundations, on the basis of the complex geological conditions and environments in China. It sums up advances in theoretical and applied researches, engineering constructions, practical experiences, case histories, and problems and developing prospects of piles and deep foundations in recent years in China.

Jan 1, 1991

By F. L. Clerc

THE lead and zinc region of SW. Missouri is interesting, not only by reason of the value of its output, which ranges in the neighborhood of ten million dollars a year, but even more because of the facilities which it offers for the study of certain forms of ore-deposits, of which the loci and genesis are somewhat obscure. Although the mineral species found in the region are few and of common occurrence, crystallization has taken place on a generous scale, and unusual forms abound in many combinations, presenting examples of pseudomorphism, paragenesis, metasomatic replacement and the action of mineral-depositing and mineral-dissolving waters. For the mineralogist, lithologist, and specialist in certain lines of metamorphism, it has peculiar attractions, while the systematic geologist will perhaps find its chief claim to attention in the simplified problem it presents, in the study of ore-deposits. In addition to the phenomena above enumerated, it presents instances of well-developed comb-structure in the ores, fissures and faults, and slickensides-features usually associated with extensive movements in the earth's crust, and believed by some authorities to prove the deep-seated origin of the ores. In connection with these occurrences, the absence of all igneous rocks from this region is noteworthy and significant. For that reason, the simplified case presented by the Joplin region, from which these rocks have been eliminated as a factor, is specially valuable. Having had unusual opportunities to watch the development of this district, I have been deeply interested in the bearing of the revelations of the Joplin mines upon questions of universal importance to the science of ore-deposits ; and it was to my great regret that the project of a meeting of the American Institute of Mining Engineers at Joplin, proposed in 1892, was

Mar 1, 1907