Search Documents

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By K. Takahashi

Generally speaking, wastewater coming from the metallurgical process for recovering precious metal contains precious metals such as gold (Au), platinum (Pt), palladium (Pd), Silver (Ag), etc., which concentration is about 10 mg/L. In addition, there are other metals such as copper (Cu), iron (Fe), which concentration varies from several mg/L to more than 10,000 mg/L. It should be noted that the concentration of metals in wastewater is relatively high, considering the fact that these metals of similar concentration can be found in ores. However, most of these valuable metals are not treated, due to the high processing cost and technical problems. Within this frame, the authors put forward a new process that includes neutralization/reduction, precipitation and fusion. The idea is to recover and recycle Au, Ag, and Pd metals as well as protecting the environment by saving the resources. It was found that this new process was able to recover more than 90% of Au, Ag and Pd.

Jan 1, 2014

By Chand F

The silver deposits of Rockvale near Armidale, N.S.W., occur in fissure veins in epi-Permian granite. The ore is fine grained, mineralogically complex, and contains twenty-seven different minerals including eleven silver minerals. The ore is characterized by a unique multiple unmixing from a sphalerite solvent. The following minerals have exsolved from solid solution in sphalerite: pyrrhotite, chalcopyrite, cubanite I, cubanite II (chalcopyrrhotite), valleriite, "brown" stannite, "olive" stannite, argentian tetrahedrite, pyrargyrite, and an unknown grey-white mineral. Several of these minerals derive from a second-stage unmixing, the immediate solvents of which are the products of earlier exsolutions.INTRODUCTIONSmall silver-rich base metal deposits occur at several localities near Armidale in the New England district of New South Wales. Chief among these are the Tulloch Mine and the Rockvale Mine at Rockvale, 27 miles SE. of Armidale, and the Tait's Gulley deposits some 15 miles NE. of Armidale.At Rockvale (Kenny, 1928), irregular lenses of lode material, principally quartz and calcite, occur along a zone of shearing in biotite granite and altered sediments. The orebodies had a maximum width of 6 ft but averaged 2 ft 6 in. The largest lens was 150 ft long and 50 ft high. The Rockvale deposits were worked for both arsenic and silver; 2,897 tons of arsenic were produced but no figures are available forsilver.Little is known of the Tait's Gulley deposits which occur in folded arenites containing small but rich veins of pyrargyrite with base metal sulphides.The sediments in these localities are possibly Silurian.

Jan 1, 1962

By G J. Delemontex, N J. Grigg

Pre-concentration of precious metal and base metal ore types is becoming more relevant with the discovery, development and operation of many lower grade deposits around the world. The fluctuations in metal prices expose many mines to risks especially dealing with low and variable ore grades.Pre-concentration, the process of concentrating the valuable metal into a smaller mass yield, effectively results in the introduction of higher feed grades to milling circuits. Gangue Rejection, the removal of lower S.G. waste rock from the circuit not only results in higher downstream grades but also potentially removes harder, non-valuable mineral, providing significant power savings within the circuit. The pre-concentration or ‘gangue rejection’ process offers a number of benefits when considering the treatment of marginal ore deposits, especially if it can be performed at a coarse crush size; these benefits include a reduction of the operating costs and the feed of more metal units to the mill.Gekko Systems has effectively utilized the Inline Pressure Jig (IPJ) to pre-concentrate the valuable metal, achieving high primary recoveries into a range of mass yields resulting in upgrade ratios between 2 and 10 times.This paper explores the benefits of pre-concentrating ‘marginal’ ore deposits prior to the milling circuit; the selective rejection of ore types that may affect either the recovery or comminution process, and also looks into the potential to effectively reduce the ‘cut-off’ grade when considering the mine planning process. Case studies of projects using the IPJ to pre-concentrate and reject gangue are also included.Pre-concentration and gangue rejection provide the potential to develop marginal ore deposits, thus providing higher grades, less gangue and more metal at a lower operating cost to producers.CITATION:Grigg, N J and Delemontex, G J, 2015. The pre-concentration of precious and base metal deposits using the Inline Pressure Jig – higher feed grades and more metal, in Proceedings MetPlant 2015, pp 296–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By S. Y. Tshipeng, A. T. Kaniki

"RÉSUMÉ La lixiviation acide d’un minerai oxydé cupro-cobaltifère en milieu non réducteur et en milieu réducteur en utilisant le Fe2+ et le métabisulfite de sodium (SMBS) a été étudiée et les résultats ont été comparés. Les tests de lixiviation ont été effectués à température ambiante, dans une pulpe à 30 % solide, avec une vitesse d’agitation de 600 tr/min, un potentiel redox de 350 mV pour les tests en milieu réducteur, et un pH de 1,8. Les tests de lixiviation avec usage du SMBS comme réducteur ont donné la meilleure cinétique de lixiviation du cuivre. Pour le cobalt, c’est l’usage du Fe2+ qui a donné la meilleure cinétique de lixiviation. L’augmentation de la dose du fer dans la solution au-delà de 5 g/L a influencé négativement les rendements de lixiviation du cuivre et du cobalt. ABSTRACT Acid leaching of a copper-cobaltiferous oxide ore in a non-reducing environment and in a reducing environment using Fe2+ and sodium metabisulfite (SMBS) was studied and the results compa¬red. The leaching tests were performed at room temperature, in a 30% solids pulp, with a shaking speed of 600 rpm, a redox potential of 350 mV for the tests performed in the reducing environment, and a pH of 1.8. The leaching tests using the SMBS as a reducing agent produced the best copper leaching kinetics. As for cobalt, the best leaching kinetics was achieved using Fe2+. An increase in the amount of iron in the solution above 5 g/L negatively influenced copper and cobalt leaching yields. INTRODUCTION La République Démocratique du Congo (RDC) est un pays reconnu dans le monde pour son sous-sol qui regorge d’énormes quantités de cuivre et de cobalt (USGS, 2014; Palisade Research, 2016). La technique qui semble être la plus recommandée pour extraire à la fois le cuivre et le cobalt des minerais oxydés cupro-cobaltifères est la lixivia-tion acide en milieu réducteur. Cette technique est appliquée par la majorité des sociétés minières qui exploitent ces minerais dans l’ex-province du Katanga en RDC, à savoir: Tenke Fungurume Mining, Mutanda Mining, Kamoto Cop¬per Company, Sicomines, Gécamines, Boss Mining, Chemaf, Ruashi Mining et Somika. L’usage d’un agent réducteur est indispensable pour l’obtention d’un bon rendement de lixiviation du cobalt. En effet, plusieurs chercheurs s’accordent sur le fait que le cobalt trivalent de l’hétérogénite (CoO·2Co2O3·6H2O) est insoluble à l’action de l’acide seul; il ne devient soluble qu’après réduction en cobalt bivalent (Mwema, Mpoyo, & Kafumbila, 2002; Mulaba-Bafubiandi, Ndalamo, & Mamba, 2007; Ferron, 2008; Seo, Choi, Kim, & Tran, 2013; Stuurnam, Ndlovu, & Sibanda, 2014)."

Jan 1, 2018

By G. Velarde

This paper presents the metallurgical results of column and stockpile leach tests with forced aeration to determine the usefulness of this process in the operational leaching at Sociedad Minera Cerro Verde S.A.A. The evolution of the aeration system is presented and also an innovative solution developed to overcome forced aeration’s main problem, which is the early obstruction of the aeration pipes located at the base of the stockpile, causing a decrease in air and oxygen levels and therefore a reduction in the metallurgical benefits.

Jan 1, 2006

By M. Arlandi, J. C. Monge

In this paper, the finite element method is used to obtain deformations of a rock tunnel. More than 3,000 numerical simulations and calculations were carried out. The analysis of this results has allowed to achieve mathematical formulations and graphs, to obtain in advance support monitored displacements in tunnelling construction, so they can be predicted before excavation and supporting woks. The application of the presented formulations and charts will aid engineers to control tunnel monitoring, reducing decision time when problems occur. The analysis is limited to cases involving elastic behaviour of the terrain for tunnels of average to good quality in rock, and to excavation sections of average or smaller dimensions for road tunnels. The results show that, in all cases, mathematical expressions to obtain induced displacements around tunnel excavations, have similar pattern than Kirsch (1898) expressions for circular excavations. As corollary of the achieved results, a method to estimate in situ natural geostress ratio K0=sh/sv , by means of convergence measurements, is presented. In diesem Beitrag wurden die Verschiebungen eines Tunnels durch die Methode de Finiten Elemente berechnet. Mehr als 3000 numerische Simulationen und Berechnungen wurden ausgeführt. Die Analyse dieser Resultate hat es ermöglicht, mathematische Formeln und Grafiken zu entwickeln, die zur Voraussage der Verschiebungen in Tunnel dienen, auch unter Betrachtung der verschiedenartigen Abstützungen. So können die Verschiebungen vor den Erdarbeiten und dem Bau der Abstützung abgeschätzt werden. Die abgeleiteten Formeln und Grafiken werden vor allem einen grossen Dienst für Ingenieure bei der Mithilfe zu zeitsparenden Entscheidungen im Tunnelbau und bei der Tunnelkontrolle leisten. Die analysierten Fälle sind auf eine elastische Modellierung des Baugrunds beschränkt, sowie auf eine mittlere bis gute Qualität des Felsens und auf die Aushebung von Abtragungsabschnitten mittlerer oder geringer Grösse für den Strassenverkehr. Die Resultate zeigen, dass in allen Fällen die hergeleiteten Formeln zur Berechnung der durch den Tunnelbau verursachten Verschiebungen um den Tunnel die gleiche mathematische Struktur haben wie diejenigen von Kirsch (1898) für kreisförmigen Bodenaushub. Als Korollarium der ausgeführten Berechnungen wird eine Methode zur Abschätzung der vorherrschenden in situ Geospannungs-Verhälniss K0=sh/sv angegeben, die von den Messungen der Verschiebungen im Tunnel ausgeht. Dans cet article, la méthode des éléments finis est utilisée pour obtenir les déformations d’un tunnel creusé dans la roche. Plus de 3000 simulations numériques et calculs ont été effectuées. L’analyse de ces résultats a permis de définir des modèles mathématiques et des abaques afin de prédire, avant l’excavation et les travaux de soutènement, les déplacements auscultés pendant la construction du tunnel. L’application de ces modèles et abaques permettra donc aux ingénieurs de contrôler les déplacements durant l’auscultation du tunnel et de réduire le temps de décision lorsque des problèmes surviennent. L’analyse est limitée au cas du comportement élastique du terrain pour des tunnels creusés dans de la roche de moyenne a bonne qualité, et à de sections d’excavation de petites à moyennes dimensions pour des tunnels routiers. Les résultats montrent que, dans tous les cas, les expressions mathématiques permettant d’obtenir les déplacements induits autour des excavations de tunnel, présentent des similitudes avec celles de Kirsch (1898) pour des excavations circulaires. Comme corollaire aux résultats obtenus, une méthode pour estimer le rapport des

Jan 1, 2003

By H. Brodie Hicks

"THE REVIVAL of the Mayo mining camp, with particular reference to the activities of United Keno Hill Mines, Limited, has been one •of the more spectacular and also one of the most important of the post-war developments in the Canadian mining field. The geological location of the camp, coupled with other natural disadvantages, have in the past limited the mining area to small-scale, highgrading operations, but the post-war improvement in metal prices has now broadened the possibilities and has led to the considerable success achieved by United Keno Hill Mines, Limited, and the present boom-type development by a whole host of newcomers to the field.LocationYukon which has an area of 207,000 square miles, is showing ever increasing possibilities as a mineral source of great value and more and more attention is being focussed on the Territory. The accompanying generalized map (Figure 1) shows the main transportation routes and mining districts.The Mayo Mining District comprises roughly the eastern two thirds of Yukon Territory lying north of McMillan river and south of the Peel. The district was one of the first in the Territory in which placer gold was discovered, but the occurrences proved of minor importance. Other minerals reported include ores of tungsten, tin, antimony, and several other metals, but of primary importance have been the ores containing silver-lead-zinc-cadmium now being developed and mined in the Keno area. Similar ores have been found over a very considerable area, extending some 50 miles north, 15 miles east, 30 miles west, and 10 miles south of the townsite of Keno Hills, Keno City, a total area of 2,700 square miles."

Jan 1, 1952

INTERNATIONAL conferences on safety in mines originated in 1912 when, in response to an invitation issued by the United States, representatives of Austria-Hungary, Belgium, France, and Germany participated in a conference held in Pittsburgh, Pa The record shows that a permanent organization was proposed to be developed through. diplomatic channels. However, the advent of war 2 years later prevented this proposal from coming to fruition. No further cooperation between the Bureau of Mines and a group having: similar interests in a foreign country took place until 1924, when formal cooperation with the Safety in Mines Research Board of Great Britain was established. Interchange of personnel and results of research under that arrangement have resulted in a number of publications in both countries and more rapid advance in knowledge than could have been obtained through the same efforts exerted independently.

Jan 1, 1950

By Bowen Li

Silicon Carbide is an excellent refractory material. Its physical properties make it extremely useful, particularly in applications where corrosion resistance and wear are important considerations. Commercial silicon carbide refractory is frequently manufactured by bonding silicon carbide particles with clay; however, clay may cause problems in the sintered products. This study investigates the potential of replacing a portion of the clay with andalusite powder. The results show that micron size andalusite powder can improve not only the strength of the refractory but also the sinterability. The mechanisms for these improvements are discussed.

Jan 1, 2006

By N. T. Lowe

The National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory (SRL), investigated a means to evaluate the potential impact of surface conditions above underground mines on emergency response activities. Recent events have highlighted the need to conduct critical emergency operations on the surface above underground work areas. Accessibility and usability of the surface, such as the ability to drill holes or deploy seismic monitoring or through the earth communications systems, are an important consideration for emergency response planning. This paper identifies critical surface conditions such as: surface waters, valley fill, highways, railroads and significant structures that must be considered in emergency response planning and in the conduct of emergency operations as they relate specifically to the seismic detection of trapped underground miners. Results of case studies indicate a need to consider the impact surface conditions may have on emergency response capabilities.

Jan 1, 2009

By M. I. Brittan

Cyanide leaching of two West African gold ores was studied in multiple laboratories to provide process-engineering data for plant design purposes. Unusually slow leach extraction kinetics were observed using routine cyanide leach test procedures with pregnant solution monitoring. Carbon-in-leach testing, however, showed normal rapid kinetic behavior, with the same ultimate gold extractions being reached in much shorter elapsed times. Kinetic curves based on washed solids assays also exhibited more typical leaching characteristics. The results bore all the hallmarks of some equilibrium inhibition of the leaching. It was surmised that ore gangue components were responsible for weakly adsorbing gold-cyanide complex reaction product, thereby holding up soluble gold in the solid phase. The term ?preg-borrowing? was coined to describe the reversible phenomenon and distinguish it from irreversible preg-robbing. The two ores investigated may represent an extreme form of a more general effect that in most instances might pass unnoticed. The effect can lead to misinterpretation of kinetic leach curve data and underestimation of calculated ore head grades.

Jan 1, 2008

By S. -H. Chang, C. -I. Lee, Y. -K. Lee

Based on results from triaxial compressive tests, an experimental damage model to simulate post-peak behaviours as well as nonlinear behaviours before peak strength was developed. In order to consider pre-peak behaviours, variations of elastic constants at each damage level were regressed by functions of confining pressure. In addition, post-peak behaviours were simulated successfully by using Hoek-Brown constants. As results, the experimental model could predict nonlinear behaviours, peak strengths and stiffness changes observed in experiments. Basé sur des résultats des essais compressifs à trois axes, un modèle expérimental de dommages pour simuler des comportements de poteau-crête aussi bien que des comportements non-linéaires avant la force maximale a été développé. Afin de considérer des comportements de pré-crête, des variations des constantes élastiques à chaque niveau de dommages ont été régressées par des fonctions de pression d'emprisonnement. En outre, des comportements de poteau-crête ont été simulés avec succès en employant des constantes de Hoek-Brunes. Comme résultat, le modèle expérimental a pu prévoir des comportements non-linéaires, des forces maximales et des changements de riidité observés dans les expériences. Auf Basis der Ergebnisse des dreiaxialen Drucktests wurde das experimentelle Schadensmodell, das sowohl das nicht-lineare Verhalten vor der maximalen Stärke als auch das Verhalten nach der maximalen Stärke simulieren kann, entwickelt. Um das Verhalten vor der maximalen Stärke zu berücksichtigen, wurden die Veränderungen der elastischen Konstante bei dem jeweiligen Schadensniveau durch die Funktionen des begrenzten Drucks zurückgegangen. Außerdem wurde das Verhalten nach der maximalen Stärke unter Benutzung von Hoek-Brown Konstanten erfolgreich simuliert. Schließlich konnte das experimentelle Modell das nicht-lineare Verhalten, die maximale Stärke und die Veränderungen bezüglich der Steifigkeit während der Experimente voraussehen.

Jan 1, 2003

By Paul M. Tyler

One of the best present-day yardsticks of the material welfare of a nation is its consumption of minerals, The United States, with only 7 percent of the world population, consumes 45 percent of the world wealth, pays the highest real wages, has the shortest working hours, and numbers the largest percentages of home owners among its population, and at the same time its per-capita consumption of minerals is far greater than that of any other nation. In 1937, British India, with roughly twice the population of the United States, used less than 2 percent as much lead, 4 percent as muck zinc, and 13 percent as much copper; even in Europe, which has three times our population and where war preparations have greatly expanded the normal needs of peaceful industries, the aggregate consumption of metals and industrial minerals other than lignite is less than the total for the United States alone. The march of civilization passed from the Stone Age to the Bronze Age before the dawn of history. It may be questioned whether man or monkey first threw stones at an enemy, but only man could have fashioned rough stones into weapons. Eoliths rudely shaped by apelike men are believed by archaeologists to have antedated by hundreds of thousands of years the existence of our own human ancestors. The primitive people that followed the retreating Ice Cap northward in early quaternary period - at least a million years ago - were fairly adept in the shaping of flints and even used a little copper. The Bronze Age, so-called, superseded the Stone Age when, around 8,000 B. C., the news spread that chunk s of natural copper could be pounded into better weapons or cutting implements than ever could be made by chipping stones. The Bronze Age gave place to the Iron Age about 1,000 B, C., and though students of modern history may speak of the Coal Age, the Petroleum Age, and the Automobile Age, and so on, these ages have all been crowded into a brief century and a half. The truth is that we still are in the Iron Age, unless perhaps we choose to call it the Age of Many Metals.

Jan 1, 1940

By Kennedy G. L

Operating experience with the pilot Lurgi carbonization plant at Morwell showed that under conventional operating conditions, although the thermal efficiency of the plant was very' high, the physical quality of the char produced was extremely poor. By variation of operating conditions to produce the slow drying rate developed by the laboratory research at the University of Melbourne, an improvement in the size of the char was achieved. A similar approach in the carbonization stage where severe breakage of the briquettes still occurred was not possible due to insufficient control over the heating in this stage. Theoretical analysis of the heat exchange process has shown that severe heating of the briquettes entering the carbonizer is a characteristic of the Lurgi system and cannot be controlled by modified operation. The plant has been closed down for reconstruction of the heating system to enable it to be used to produce hard char.INTRODUCTIONAn experimental carbonization plant was operated at the Morwell Works of the 'Gas and Fuel Corporation from November 1958 until July 1959. This plant was built as a pilot plant by the Corporation to designs supplied by the Lurgi Gesellschaft fur Warmetechnik and had the nominal capacity to carbonize 25 tons of brown coal briquettes and to produce 11 tons of char per day. The briquettes were supplied from the· normal production of the Yallourn briquette factory and the 2t in. I-type briquette was the largest size which the plant could handle.This carbonization plant represents the intermediate stage of development between the laboratory research at the University of Melbourne and the commercial production of hard char as a metallurgical fuel. It is intended in the first place for the study of the technical problems in the handling and...

Jan 1, 1960

THE solid nonmetallic inclusions present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, how- ever, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general, the term non- metallic inclusions seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those occurring as a result of reactions taking place in the body of molten or solidifying metal and (2) those resulting from mechanical incorporation of refractories or other materials with which molten steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag-stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulfides but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from molten or solidifying steel may be caused by: (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change

Jan 1, 1951

The conclusions reached by den Tex after a study of the fabric of some rocks from Broken Hill have been used to support the epigenetic hypothesis for the origin of the ore, first by Edwards (1959, p. 70) and then by Stillwell (1962, p. 131) in his criticism of Segnit's (1961) views. Den Tex claimed that the petrofabric study provided "independent evidence that the ore, at least in its present form, post-dates all events of a diastrophic nature in the area concerned".Repetition of this claim by Edwards and by Stillwell and the lack of any criticism of den Tex's work for more than three years implies its general acceptance by geologists in Australia. Therefore it appears necessary to examine parts of den Tex's paper in detail to show that his, conclusions are unwarranted. The major weaknesses in his study are that1. the petrofabric study was inadequate to warrant any major conclusions, and2. the petrofabric data allow alternative conclusions.Den Tex made a single visit to the field, collected six carefully selected specimens and presented quartz and· biotitepetrofabric diagrams for two specimens, quartz-diagrams alone for three more and included three diagrams of the orientation of c-axes and fractures in one specimen. It is not reasonable to come to firm conclusions about the origin of such a complex area as Broken Hill on such inadequate data, despite den Tex's claim (p. 87, lines 22 and 23) that "a thorough investigation of the quartz-fabric of the wall rock was undertaken".Den Tex's interpretation of each diagram is open to criticism, and alternative (and to my mind, preferable) interpretations may be made. It is impossible to evaluate den...

Jan 1, 1962

By S H. Son, M K. Wang, H K. Jeong, B K. Cho, J I. Park

The utilisation of low-grade raw materials such as fine iron ore and semi-soft coking coal, and reduction of CO2 emissions are important issues in the ironmaking process. To solve these issues, a new process called PosPRA (POSCO prereduced agglomeration process) has been developing at POSCO. It focuses on the reduction of carbon composite iron ore briquette in travelling grate. In this study, the possibility of manufacturing the prereduced agglomerate (PRA) under oxidising atmosphere with travelling grate and the optimum manufacturing conditions of carbon composite iron ore briquette are investigated. The results have shown that controlling the temperature and oxygen potential in the range from 1100 to 1200°C and below 10 vol per cent respectively is very important to increase the reduction efficiency of briquette in travelling grate. High quality properties of the green briquette and PRA could be manufactured by using the briquette mixed with 20 wt per cent of coal under 0.1 mm in size under compacting pressure in the range from 3 to 7 t/cm. Adding 1 wt per cent water as a binder is proper under the condition of high compacting pressure. In a pot grate test, the compressive strength and metallisation degree of PRA are achieved over 150 kgf/p and about 55 per cent respectively, at bed temperature 1150°C and oxygen potential of 10 vol per cent when 20 wt per cent of coal is mixed in the briquette.CITATION:Wang, M K, Son, S H, Park, J I, Jeong, H K and Cho, B K, 2017. Development of prereduced agglomeration process using carbon composite iron ore briquette in travelling grate, in Proceedings Iron Ore 2017, pp 111–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Don M. Coulter

"INTRODUCTION The Lookout Mountain coal deposits were examined by J.L. Stratton, an engineer of the Bureau of Mines in April and May 1943. The area investigated includes that part of southern Lookout Mountain in townships 4 to 8, south, ranges-9 to 11 east, and contains approximately 140 square miles in DeKalb and Cherokee Counties in northeastern Alabama (fig. 1.)Six coal seams having a minable thickness of 18 or more inches are represented in the area. The third seam, known locally as the Hill seam, has been correlated with the Upper Cliff No.1 seam and is referred to as such throughout this report. The preliminary investigation indicated that the Upper Cliff No. 1 seam is a low-volatile, high-grade coking coal. The work done on this project was confined principally to determining the amount and grade of coal in this seam.The only existing maps of mines in the area were one of the Lookout Fuel Co. at Lahusage, Ala. (fig. 2), and one of the Lookout Mountain Iron Co. at Battelle, Ala. (fig. 3), Consequently, to gain some knowledge of the grade and tonnage mined, surveys of the other mines were necessary. Many of them were caved, and many were filled with water, necessitating considerable preliminary work."

Feb 1, 1947

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951