Search Documents

Treatment of Gold-Bearing Oxide High-Clayish Ores The analysis of modern state of treatment technologies of gold-bearing oxide high-clayish ores showed that the main method applied both in Russia and abroad is sorption leaching and heap leaching with preliminary granulating. The use of any of these processes depends on many factors including average gold grade, site and area of a deposit, clay content and etc. The two processes are often used at the same deposit. In this case, rich ores are treated according to a plant technology, poor ores and ores with cut-off grade are treated with heap leaching. Both technologies possess their own advantages and disadvantages. A plant technology is characterised by high recovery with higher capital and operating costs at the same time. Lower recovery during heap leaching can be attributed to an unstable quality of ore granulating due to both technological and weather conditions. In case of poor high-clayish ores, the use of a combined ore treatment is possible and profitable. It includes the ore disintegration and a clayish fraction treatment by using a heap leaching. In this case, capital and operating costs reduce in comparison with a plant technology and the recovery increases in comparison with heap leaching. Sometimes it reaches a plant recovery. These ores possess special features. As a rule, gold is associated with ore fraction, so it liberates readily from the association with ore ore-forming minerals even with relatively coarse grinding explain their high solution velocity in a hydrometallurgical cycle. Clayish ores are characterised by high sorption activity to gold cyanide complexes as well as extremely low velocity of filtration and thickening of slimic pulps at the same time. The paper describes the options of oxidised high-clayish ores treatment, such as, a plant technology (PIP and CIP process), heap leaching and a combined technology (disintegration, heap leaching of a crystalline fraction and sorption cyanidation). The obtained results were used when selecting a treatment technology and during construction of a plant for oxidised high-clayish ores treatment.

Sep 13, 2010

By Ike Madingoana, Stephan van Zyl, Antoine F. Mulaba-Bafubiandi

"The study presents a control strategy implemented at the Nkomati nickel mine flotation plant for process stabilization and improvement. The control strategy involves flotation concentrate volumetric flow rate stabilization and the flotation cell mass pull control. The flotation concentrate volumetric flow rate is operated at a fixed set point. The initial control strategy involved varying the flow rate to maintain the concentrate tank level thereby reducing pump cavitation. The flotation cells mass pull control comprises air rate manipulation into the cells with the exception of the recleaners. The air rate into cells is automated to adjust based on the concentrate tank level variation. The control strategy was implemented on the roughers, cleaners and the recleaner circuit. The recleaner cells air flow rate is adjusted based on the MgO content in the concentrate. The stabilization of the flotation concentrate volumetric flow rate and the mass pull by aerate automation will increase the scope of optimization for further process improvement. The immediate benefit of the control strategy implementation was plant stability. Disturbance to the flotation cells downstream was minimized due to stable flow rate, and the air addition manipulation ensured that the concentrate tank levels are maintained, minimizing pump cavitation. INTRODUCTION Froth flotation is a challenging process because it is influenced by a large number of factors, including the flotation feed characteristics. One of the ore types mined at Nkomati nickel mine is the main mineralized zone (MMZ). The MMZ ore is hosted in the Uikomst complex, a Ni-Cu-PGE-Cr- mineralized, layered basic to ultra-basic intrusion which hosts commercially viable magmatic base-metal sulphides (De Waal et al., 2001). The MMZ ore is a heterogeneous sulphide mineral resource with a varying sulphide mode of occurrence and texture. The beneficiation of the complex sulphide ore is challenging due to the presence of impurities in the ore. The impurities report to the flotation final concentrate and penalties are levied if the impurities are beyond the contractual limits."

Jan 1, 2015

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By D. F. Malan

This study reviews the concept of squeezing (large time-dependent deformation) in rock and investigates the possibility of this phenomenon becoming more pronounced in the planned ultra-deep mines of the South African gold mining industry. Although squeezing behaviour is not commonly found at the current depths of the gold mining industry, it is observed at Hartebeestfontein Mine due to a combination of weak rock and high stresses. Calculations based on the average strength of the Witwatersrand quartzites and the competency factor used to identify squeezing conditions in civil engineering tunnels, indicate that there is an increased risk of squeezing behaviour in ultra-deep mines. This will adversely affect the profitability of these mines and highlights the need for further research into the time-dependent behaviour of rock. Finally, the current support strategies in squeezing conditions are reviewed.

Jan 1, 1998

By J. B. Rasmussen

As part of a purchase of a fleet of Caterpillar 785 trucks, Round Mountain Gold Corp., Cashman Equipment Co. and Caterpillar Inc. entered into a four-year contract for the major maintenance of the fleet of trucks. This contract includes fixed costs and guaranteed availability. The results have been excellent, and the fleet of trucks performs well. History The Smoky Valley Common Operation is a unique mine. Through a mixture of diligence and foresight, it has become the largest open-pit, heap leaching gold mine in the world. This was no small feat considering the remote area surrounding the mine. Round Mountain is located in north-central Nye County, NV. To the east of the town and mine lies the Central Toquima mountain range. To the west is the Toiyabe mountain range. Between them is the Big Smoky Valley, a flat expanse of sagebrush, salt grass and fine dirt.

Jan 1, 1991

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By John C. Machisak

INJURY experience and employment data at all metal mines in the United States and Alaska are presented in this Information Circular for the calendar year 1958. This publication covers the metal mining industries, and contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. These operations report injury and employment information annually to the Bureau of Mines on a voluntary basis. The Bureau is authorized to make requests for such data, and the information submitted contributes immeasurably to the promotion of safety in the metal mining industry. Every effort has been made to make the annual canvass as complete as possible. This publication contains, along with production and development workers, the office employees at the mine location. The metal mines identified in this publication are classified according to the mineral ores mined; that is, copper, iron, lead-zinc, gold-silver lode, gold placer, and miscellaneous metals.

Jan 1, 1962

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency In low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were Investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas, The results have been summarized In terms of maximum communication range expected per seam and noise condition. Scatter gain Is further explored as a simple measure of energy coupled to conductors.

Jan 1, 1978

By Gorr W. W., Wyche E. H, R. Smith

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Gorr W. W., R. Smith, Wyche E. H

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Noel Dent

The Electrodet@ Electronic Detonation System Wilere are we going with regard to Accurate, Reliable, Easy to Use and Cost Effective Initiation using electronic initiation techniques? Improvements and applications in theJierd

Jan 1, 1995

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption of this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 million tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and -is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably arc in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By J. P. Carson

The works of the Tula Iron Company are in the Republic of Mexico, State of Jalisco, twenty-eight leagues southwest of Guadalajara, ten leagues northwest of the town of Sayula, through which passes the projected line of the Mexican National Railroad. Its geographical position would be about: latitude, 20' 10' N., longitude, 40 35' w. of Mexico City. The surrounding country is a rolling plateau, 6000 feet above the sea, enjoying the most magnificent climate in the world, the average temperature being about '70'. The works were commenced in 1850 by a company with very small capital, having not the least idea of the undertaking. They soon fell into the hands of the money-lenders, and after changing

Jan 1, 1879

By D. W. Fuerstenau

In 1940 Schuhmann1 showed that the size distribution of a comminuted material can be expressed by the following empirical relationship: y = 100 (|f [i] where y is the cumulative percentage of material finer than size x, k is a size modulus, and a is a distribution modulus which is constant for a given material and machine. During the past few years, considerable emphasis has been given to the investigation of the extent of size reduction resulting from the expenditure of mechanical energy in crushing and grinding. Recently Schuhmann' presented a derivation of the energy-size reduction relationship by postulating that comminution in a device such as a ball mill can be considered to be the summation of many single comminution events, each of which yields a size distribution of particles following the Schuhmann size distribution equation. By grinding

Jan 1, 1961

"It is projected that the reactivity of acid generating tailings and waste rock can be minimized by reducing the access of oxygen by placing these materials under water in natural or manmade lakes. A project under the MEND and B.C. AMO Task Forces has been in progress for four years to evaluate active and historic tailing sites in B.C. and Manitoba. The sophisticated geochemistry studies conducted on the interstitial pore water has illustrated encouraging results which are discussed. The additional studies which are needed to complete the scientific database for the study sites, for achieving regulatory and public approval and for the engineering of application of this method of control are outlined.IntroductionWorld wide research effort is in progress to find the solution to the acid mine drainage problem. A great deal is known about acid mine drainage but much work is required to find economic and effective approaches to the problem. Two coordinated programs have been initiated recently in Canada: the National Mine Environment Neutral Drainage (MEND) program and the British Columbia Acid Drainage Task Force.Disposal of tailings materials under a water barrier such as a natural lake, is thought to be one solution to prevent acid generation by preventing oxygen and bacterial action on the sulphide surfaces. The deposition of reactive tailings materials under water in natural lakes has been used historically at various mines in Canada. However, there has never been a thorough review of the long and short term impacts of historic sites which may provide crucial information to understand the physical, chemical and biological processes which are taking place.This paper provides a general overview of a series of studies which examine the general biophysical characteristics and the sediment geochemistry of four lakes where subaqueous disposal has been or is currently being used for acid generating tailings. The subaqueous disposal studies have been conducted from 1989 through 1991 and were initiated and supported by both research task forces. The objectives of this paper are to summarize the history and the background information of the studies conducted, the general results obtained from each lake, an overview of the major collective results and the additional work which is required to achieve the final objective of developing criteria for applying this technology in the industry."

Jan 1, 1992

By Snehamoy Chatterjee, Dharmasai Eshwar, Aref Majdara, Rennie Kaunda, HUGH MILLER

The U.S. mining industry has made progress in reducing accidents and injuries, but interpreting safety data remains difficult due to changes in workforce size and productivity. The Mine Safety and Health Administration (MSHA) uses tools like the pattern of violation (POV) and significant & substantial (S&S) calculator to monitor safety, though these have limitations. To address this, we developed an information entropybased risk (IER) index that combines various safety metrics, including citations, penalties and injuries. Using data from 2011 to 2020, the IER index was validated with statistical methods and clustering algorithms to ensure it accurately reflects risk levels. The analysis showed clear differences in risk across mining sites, proving the index’s usefulness. The IER index was then applied to a coal mine to demonstrate its effectiveness. This new tool can help mining companies better assess their safety risks and take action to improve workplace safety.

Nov 1, 2024

By Laura Bastemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to loo0 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of film based cameras.

Jan 1, 1997

By B. E. Field

Cobalt is a silvery white metal with a slight bluish cast. It strongly resembles nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ decidedly in their properties from those of nickel. The name "cobalt" was derived from the German Kobold, meaning goblin, and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was not isolated until about the middle of the eighteenth century, by Brandt, although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470.

Jan 1, 1935

By D. S. F. Silva

A survey of 120 recent NI 43-101 technical reports was conducted to evaluate the current state of practice regarding resource classification techniques. The most common classification techniques are based on search neighbourhoods (50% of recent reports), drill-hole spacing (30% of recent reports), and/or kriging variance (6% of recent reports). Two new techniques are proposed. The first is based on kriging variance and involves removing one or more drill-holes with the highest weights while performing kriging and using the resultant kriging variance for classification. This technique has the advantages of variance-based techniques and reduces artifacts. The second technique is based on conditional simulation and uses a moving window approach for classification at the desired selective mining unit resolution based on larger production volume criteria. This technique has the advantage of accounting for heteroscedasticity, which is a common characteristic in mineral deposits, and also reduces artifacts since a production volume scale is considered for the actual classification. The drill-hole spacing, search neighborhood, kriging variance, and simulation-based techniques are described and compared for 2D and 3D examples with regular and irregular drilling patterns to highlight the advantages and disadvantages of each method.

Jan 1, 2014