Search Documents

By Zdzislaw Specht

THIS paper discusses elementary laws pertaining to seismic reflection methods and presents a general and simple criterion for determining the direction of dipping of a reflection horizon from observational data of distance and time. The important development of practical geophysics and the successful results obtained in America, Germany, and other countries, caused introduction of geophysical methods of prospecting in Poland. Of all methods, seismic prospecting has proved most successful in the area of the Carpathian foreland, where new oil reserves are to be expected. Because of the great depth of the sedimentary column in that area, rang-ing sometimes over 2000 meters, it was obvious that only the seismic reflection method could give reliable information regarding the structural features of these strata at such a depth. During the experimental surveys it appeared that the complicated geological conditions of that area do not always allow prediction of the depth and the angle of dipping of reflecting horizons, and for that reason information about the inclination of a given horizon has great importance in the determination of subsurface structure. Therefore the problem arises of obtaining from seismic reflection data reliable information as to the direction of dipping of reflecting strata, without any previous knowledge of the average velocity and depth of geologic horizons under consideration.

Jan 1, 1940

By Harshad Bhagwat

The objective of this work is to investigate the inadequacies of current CFD based methodologies of model development for predicting combustion behavior of pulverized coal in furnaces. In the present paper, a steady state CFD model was used for in-depth analysis of pulverized coal combustion. The model accounts for turbulence, coal combustion, convective and radiative heat transfer and motion of coal particles. It also uses coal combustion models to account for important processes such as devolatilization, combustion of char and the evolution of fuel nitrogen during coal combustion. The model predicts fluid flow, heat transfer, progress of combustion and pollutant formation (NOx, etc.). The model uses several parameters, which need to be tuned with experimental data, which is not only limited in quantity but also insufficient in detail. Various existing methodologies like part calibration method for tuning of the parameters are discussed. In the present work, the parameters associated with coal combustion models were tuned and validated with published data obtained from an experimental furnace using one such part calibration methodology. The results clearly show that the model predictions differed with the experimental data not only quantitatively but also qualitatively. These discrepancies were attributed to part calibration methodology. A detailed parametric study was carried out to demonstrate the importance of parameters from various classes, namely, combustion kinetics, heat transfer, process and geometry parameters, and CFD model parameters. This investigation clearly indicates that parameters from different classes have significant effect on combustion behavior. The discrepancies in current methodology are discussed and a need for comprehensive methodology is highlighted. Keywords: pulverized coal combustion, computational fluid dynamics (CFD), pollutant formation (NOx), mathematical modeling

Sep 1, 2012

By J. Kretschmann, O. Drusche, S. Krause

Mining companies are caught between the growing international relevance of ESG (Environmental, Social and Governance) investments and the need to secure their “social license to operate” by considering the needs of their stakeholders. In the search for sustainable business models, the concept of the circular economy (CE) is gaining momentum among practitioners and scholars, as it enables the creation of shared value and thus strengthens the trust of investors and stakeholder relationships. However, there is a lack of a sectorspecific CE framework providing guidance to decision-makers in evaluating promising activities. A gap, which this contribution aims to address.

Mar 2, 2022

By William R. Yernberg

What a difference a year makes. One year ago, the iron mining industry and the steelmaking industry in the United States were in trouble. Many companies were in bankruptcy, and talk of plant and mine shutdowns was rampant. At that time, it seemed difficult, if not impossible, to remain competitive with imported steel. In addition, the World Trade Organization declared as illegal the tariffs placed on imported steel. And many questioned the viability of the ironmining and steel industry in the United States. At that time, global economic conditions were the main contributors to the industry’s problems. However, since last year’s meeting, changes in global economics have actually helped the steel industry in the United States. Heavy global demand for steel has caused raw-material shortages worldwide. Much of the increased demand is a result of the economic boom in China. In addition, because of a weak U.S. dollar and higher international freight rates, steel imports into the United States have been reduced to about 50 percent of recent levels. These factors have contributed to a rebirth of the U.S. iron mining and steel industries.

Jan 1, 2004

By H. Thomas, I. N. M. Nday

"*Paper written on project work carried out in partial fulfilment of BSc.Eng (Mining Engineering) degreeThe optimization of the cycle time to increase productivity at Ruashi Mining was an on-site project investigation conducted from December 2017 to January 2018. The main objective of the investigation was to determine the actual cycle time components. These comprise the queuing time, loading time, hauling time, and dumping time of ADTs (articulated dump trucks). Data was also collected on two hydraulic shovels to identify where these could be optimized. The actual cycle time obtained was compared to the theoretical cycle time to ascertain the constraints, which affect productivity. By applying Systems Thinking to the cycle time, man-made constraints of the actual cycle time were identified and recommendations to mitigate them suggested to optimize the cycle time. However, rainfall is a natural constraint that adversely affects the actual cycle time, and which cannot be mitigated.In addition, both the theoretical and actual cycle time were analysed, as well as the theoretical and actual productivity for the year 2017. Based on the findings, conclusions and recommendations were made to optimize the cycle time. IntroductionThe aim of the project was to increase Ruashi Mining’s productivity by 39%, from about 7.537 Mt of broken material mined to 12..367 Mt targeted in 2017.BackgroundRuashi Mining is a copper (main commodity), cobalt (by-product), and acid producer located in the Democratic Republic of Congo (DRC), 10 km from the city of Lubumbashi. Figure 1 shows the location of the Ruashi Mining open pit.Ruashi Mining started production in 1911 and in 2005 the mine was registered as a DRC company owned by Metorex Group Limited. In November 2013, the Chinese company Jinchua Group International Resources Co. Ltd. bought a majority stake in the business. Ruashi Mining currently produces 38 000 t of copper and 4400 t of cobalt per annum. The company has contracted NB Mining (a contract mining company) to transport its ore. To optimize the productivity of the mine, considering ore flow delivery at Ruashi Mining, the cycle time is the indicator used in this project. The cycle time components were recorded on site using a stopwatch."

Jul 1, 2019

Thirty mixed cultures of microorganisms from soil, water and mineral samples from the Groote Eylandt Mining Company mine site were approximately three times more effective in biodegrading manganese dioxide (34± 18 mg Mn++/1/day) than sixteen purified strains (11 ± 10 mg Mn++/1/day) isolated from the primary enrichment cultures. Two pure bacterial genera identified as a Pseudomonad and a Bacillus, with an excess MnOz and nutrient, were able to dissolve 106 mg Mn++/litre/day in mixed culture compared with 29 mg Mn++/litre/day when grown separately.

Jan 1, 1983

By Graham W. Marks, Betsy M. Jones

"Recently4/ it was shown that the total energy method5/ of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing this work, the present report deals with analyses for beryllium, zinc, cadmium, and indium.There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved.As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is associated with zinc and cadmium in zinc ores.The authors wish to acknowledge the valuable assistance of the staff of the Bureau of Mines Analytical Laboratory who made the chemical analyses and supplied the ore samples used in this work.A brief description of the procedures followed in making the standard curves and analyses is given below; a detailed discussion will be found in an earlier paper.6/Basically, the procedure for determining a standard curve consists of two parts: (1) Choosing a suitable line in the spectrum of the element to be determined and (2) determining the variation in the intensity of this line with the amount of the element burned in the arc."

Nov 1, 1948

By W. R. Crank

[Rock bursts are phenomena associated with mining operations, particularly with deep mining, although they occur throughout a wide rump, of depth, from 600 feel downward. The intensity is usually in direct proportion to the depth, varying from a loosening and sloughing off to a violent rupture, giving rise to the term, "explosive rock." The more or less violent breaking of rock in mine working, tins been variously designated as " flaking," "pressure hoists," "strain bursts," "bumps," "quakes," and "air blasts," which indicate opinions as to cause and effect. The term "air blast" lots probably beat most widely used, and naturally so, as a more or less rapid movement of air often accompanying the more violent phenomena of rock failure. Furthermore, there is an implied if not definitely expressed degree of magnitude in the action designited by a given term and in the cause and character of the action. For example. flaking, pressure bursts, and quakes are terms ranged to indicate action of increasing magnitude; and pressure bursts, strain bursts. bumps, and quakes are ranged according to the cause and character of the action.]

Jan 1, 1929

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation.

Jan 1, 2007

In common with general experience in the iron-making industry overseas, Australia has in recent years suffered a deterioration in the physical quality of her iron ores in their suitability as a direct blast furnace feed. The increasing amounts of fines and the more friable nature of lump ore, especially in the ore from the Cockatoo Island deposits in Yampi Sound, Western Australia, have focused attention on problems of ore preparation and agglomeration, particularly sintering.Although very small pilot scale Dwight-Lloyd type sinter machines were operated at the steel-making centres at Newcastle and Port Kembla during World War II, no sizeable capacity was installed, so that ore was charged to the blast furnaces almost entirely unscreened, and the resultant flue dust was stockpiled.Towards the close of the war, the pilot plant at Newcastle was replaced by a small machine, adjacent to the flue dust stockpile, with a rated capacity of some 20 tons per hour. After approximately five months of part-time operation, this plant was closed down in January, 1945. Production was not resumed until December, 1950, when, due to a temporary ore shortage, it was decided to supplement available ore with sinter produced from the large flue dust stocks of about 300,000 tons. In spite of mechanical and process difficulties, inherent to the design of the plant, operation was continued on a two-shift basis, with several shutdowns for extensive overhaul and plant alterations, until September, 1954, when production was put on a three-shift basis. Addition of Yampi ore fines to the sinter machine burden was not commenced...

Jan 1, 1957

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By Ian Gordon Hall

El presente texto describe el proceso de recuperación de las partículas ultrafinas de casiterita en los relaves de la mina San Rafael a través de diversas pruebas metalúrgicas, donde se usaron dos tipos de concentradores centrífugos, los cuales indicaron la posibilidad de una recuperación de 50%, produciendo concentrados de 50% Sn. Asímismo, se instala una planta piloto donde se verifica el proceso de las distintas configuraciones y combinación de equipos, como el efecto de las cargas circulantes. Paralelo a ello, se realizan pruebas para aumentar la ley de los concentrados primarios y así obtener concentrados finales a través de concentración gravimétrica.

Sep 12, 2005

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

By F. Haessner, M. Wilkens, U. Jakubowski

ThOUGH at present there is a wide range of possibilities for the quantitative determination of preferred orientations, pole figures of identical specimen material have not been determined by different methods as yet.''' In this paper a comparison of (Ill), (200), and (220) pole figures is presented which were obtained from a 95 pct cold-rolled high-purity cop- per sheet (99.9998 pct Cu), by three different methods. The three methods are: a) The combined X-ray reflection-transmission technique of plane samples by schulz3 and Decker, Asp, and Harker. 4 A Siemens texture goniometer was used. The experimental details are described elsewhere. 6 b) The X-ray reflection technique of spherical samples by Jetter and Boric.' A Siemens texture goniometer with some modifications was used. The samples were prepared by sticking 140 polished sheets together with an adhesive and machining a sphere (20 mm diam).* Additional

Jan 1, 1967

By Andrea Brickey, JUDITH BUABA, RICHARD AMOAKO

The global mining industry has recorded significant declines in accident and injury rates attributed to the advancement in technology, increased enforcement, and safety consciousness. A goal of the mining industry is to achieve zero injury and occupational illness on all mine sites, prompting increased research into ways to further reduce mine accidents. A machine learning technique known as multiclass logistic regression is applied on a 10-year injury dataset from the Mine Safety and Health Administration (MSHA) to determine a miner’s susceptibility to a class of injury and to help identify significant risk factors associated with different classes of injury. The data is aggregated based on injury classification to provide statistically relevant results. The analysis identifies specific risk factors that influence a mine worker’s susceptibility to a given class of injury, i.e., non-fatal with no days lost or restricted activity, non-fatal with days lost and/or days of restricted work activity, and fatal and total permanent or partial permanent disability. These factors include miner’s age, mine type (coal vs. non-coal), experience on the current job (years), shift start time, employment type (operator vs. contractor), mining district, and type of accident. The results of the analysis indicate that a miner’s experience on the job, i.e., the number of years worked in a current job, is a significant risk to injury occurrence, even for those with decades of total mining experience. We further show the differences and similarities between the surface and underground mine incidents.

Nov 3, 2020

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By Ling Wu

The development of pyrometallurgical technologies has been focused on new smelting reactors, but the proposal for new converting reactors has been substantially lower. Up to today about 80% of copper matte is treated by the traditional P-S converters which have the weakness of pollutant fugitive emissions. Therefore, the continuously converting processes for treating molten matte have been studied and developed. In July 2017 the "oxygen-rich side blowing smelting + multi-lances top converting & fire refining" continuous copper treating process was commissioned. This process was designed by ENFI and YanTai GuoRun Copper Smelter. In this process, oxygen rich side blow technology is adopted for smelting, which is a new type of side blowing smelting furnace to produce high-grade copper matte. The converting adopts the horizontal multi-lances top-blowing continuously converting process, which eliminates the transportation of molten melt and the SO2 fugitive emission. The intermediate products of this process, copper matte and blister copper is fed into the furnaces respectively through launders. This new process is more advanced, more reliable and more environmentally friendly. Until now, this process in the GuoRun copper smelter is operating smoothly. An increasing number of projects which use this process are under design and construction in China. INTRODUCTION At present, there are many advanced smelting technologies for copper concentrate, such as oxygen bottom blowing smelting, flash smelting, top lance smelting (including ISA and Ausmelt furnaces smelting), side blowing smelting, Mitsubishi smelting, etc. At the same time, there are many copper matte converting technologies such as oxygen bottom blowing continuous converting, flash converting, Ausmelt top lance converting, horizontal multi-lances top blowing converting, Mitsubishi converting, P-S converter converting, etc. The final blister copper fire refining technology mostly adopts rotary anode furnace. Therefore, in the process of processing and extracting the copper from concentrate to produce anodes, there are dozens of technology combinations. Among them, the non-continuous converting technologies for molten or cold matte are often adopted in the converting process. The traditional P-S converting technology had been utilized for over one hundred years, with a mature, reliable and simple operation, also has advantages in the secondary scrap smelting of a wide range of quality. However, due to its batch operation, frequent roll in and out, poor sealing, considerable air infiltration, needs for ladles for molten phases transportation and other characteristics, the technology has a serious pollution problem due to fugitive SO2. At the same time, in the cold matte converting technology, the molten matte needs to be cooled and then processed. The sensible heat of the molten matte cannot be recovered, and the preparation process is needed in the process. Therefore, both energy consumption and investment are relatively higher.

Jan 1, 2019

Forecasting, particularly when applied to meaningful issues, is known irreverently as 'futurology'. There is quite a range of opinion ext.ant in the world when mineral resources are looked at. The opinions range from the doomsday view that there will be acute shortages of all essential commodities, to the optimistic outlook that new 'discoveries will prevent any possibility of shortages. The environment is, as yet, only studied locally and quite parochially; surprisingly there is little integration when considering the spatial atmosphere, the seas in depth and the earth's crust.

Jan 1, 1981

By E Villaescusa, C Drover

Fully resin encapsulated threaded bar and cement grouted cable bolts are common forms of reinforcement for underground mining excavations constructed at great depth. These elements are frequently installed to dissipate the dynamic loads caused by violent rock mass failure mechanisms. Failure of the ground support scheme without rupture of the reinforcement elements implies that the maximum energy dissipation capacity of the scheme was not utilised. The ground support damage mechanisms are useful to identify in this context as they reveal vulnerabilities which limit the scheme performance. This paper presents a number of field observations of reinforcement performance following a range of dynamic loading conditions. It was observed that fully resin encapsulated threaded bars exhibit variable behaviour. In particular, inconsistent resin encapsulation was frequently observed in combination with surface support failure, indicating that the retention function of these elements may allow preferential loading of the surface support system. Observations of cement grouted, twin-strand plain cable bolts reveal a common mode of damage involving differential displacement across the steel-grout interface and slip of the cable within the borehole. This is common where strands are not mutually tensioned with barrel and wedge assemblies. Surface fixtures that exceed the strength capacity of the cable strand are required in order to minimise the occurrence of this response. Improved load transfer from the rock mass and surface support to the cable can thus be achieved, particularly where small block size failure occurs.CITATION:Drover, C and Villaescusa, E, 2016. Field performance of fully encapsulated reinforcement during violent failure events, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 659–668 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016