Search Documents

By John R. Reynolds

This paper describes mining and milling methods of the American Smelting & Refining Co. at the Morning mine in the Mullan area of the Coeur d'Alene mining region in Idaho and is one of a series of Bureau of Mines reports dealing with methods and costs of mining throughout the United States. The Morning mine has been described previously in a Bureau of Mines report published in 1930,2/ and the milling methods and costs at the Morning concentrator were presented in a Bureau of Mines report published in 1932. 3/ These reports are supplemented by this publication, which presents data to show the effect of changing times and conditions on a typical medium-size mining operation during the latter part of its history, when costs were rising and production was from increasingly greater depths. The report contrasts two periods in the history of the mine-periods not too far separated in years but considerably different in economic conditions. During the first period (1939) costs of labor and materials were moderate, mining operations were just being transferred from the main shaft to deeper workings opened from the offset shaft, and the operation prospered. During the second period (12 years later) production costs had increased following the national trend in all industry, mining was from greater depths near the bottom of the ore body, and the operation was becoming unprofitable. Mining on the lower levels of the property ceased in 1953.

Jan 1, 1956

By F. M. McEvoy, E. J. Steadman, R. Murfin

In England, the provision of aggregate is determined by the historical relationship between construction and aggregate consumption. This approach does not necessarily lead to sustainable decision-making and can be seen as being driven by political expediency, rather than reasonable environmental consideration. The introduction of the statutory requirement for Strategic Environmental Assessment (SEA) in the UK has provided the opportunity to examine this issue on a more rational basis. This paper provides a practical application of a SEA based approach, to the provision of aggregates at a regional level. The process, underpinned by relevant information on resources and environmental assets, suggests that alternative supply scenarios for aggregate provision are tested in a transparent, consistent manner with increased genuine stakeholder consultation. It supports a move away from "predict and provide" approaches to one where aggregates are sourced with the best balance of environmental costs and benefits.

Jan 1, 2005

By A. K. Mishra

The mineral industry is leading towards a technology driven optimization process. Drilling and blasting are such unit operations in a mine, which can alter the balance sheet of the mine if not planned properly. The development, improvement and utilisation of innovative technologies in terms of blast monitoring instruments and explosives technology are important for cost effectiveness and safety of mineral industries. The ever-growing demand of mineral has compelled the industry to adopt mega opencast projects with big equipments. This has necessitated use of few hundred tonnes of explosives in each blast. The bulk delivered fourth generation explosives has solved the problem of explosive loading to a large extent. The priming of bulk delivered explosives in Indian mines uses the conventional PETN/TNT based cast boosters. As the conventional cast booster possess safety problems in terms of handling and use, so Indian Explosives Ltd., has developed an emulsion based cast booster (Powergel Boost).

Jan 1, 2005

By P. K. Leung, S. R. Allada, P. M. Dranchuk, D. Quon

The alternating direction explicit procedure (ADEP) makes use of the boundary conditions to reduce multi-dimensional problems to a series of one-dimensional problems. The method, previously applied to reservoirs containing only an under-saturated oil, has now been extended to cover the case of natural gas reservoirs. l his involves solving a non-linear partial differential equation, application of the procedure is straightforward and no calcuIational problems were encountered. INTRODUCTION There has been a growing interest in formulating mathematical models of petroleum and natural gas reservoirs — models which permit the engineer to examine and evaluate the physical and economic consequences of various alternative production policies. The tremendous reduction in the cost of solving such models in recent years has made possible their use as an almost routine management tool. This reduction is the result not only of improved computer hardware but also of the development of more efficient mathematical techniques. The present paper is concerned with the application of a recently proposed numerical method (ADEP) to two-dimensional gas reservoirs. STATEMENT OF THE PROBLEM Given a two-dimensional Region R, bounded by a closed Curve C (Fig. 1) such that the behavior on Curve C is known, the differential mass balance for each fluid phase in R, neglecting gravitational effects and assuming Darcy's law for fluid transport, can be written as:

Jan 1, 1967

By T. H. Yang, K. K. Lee, Z. Z. Liang, C. A. Tang, L. C. Li, Y. Tsui, L. G. Tham

Abstract: A series of numerical tests of hydraulic fracturing in heterogeneous rocks were performed to investigate the influence of pore pressure magnitude and gradient on initiation and propagation of tensile fractures. The numerical tests were run with a Rock Failure Process Analysis code, F-RFPA2D, incorporated with a Flow-Stress-Damage coupling model (FSD). To investigate the influence of pore pressure magnitude on fracture behaviour, “pinch-off” breaking tests, originally employed by Bridgeman to investigate the effective stress law for tensile fracture in a uniform pore pressure field, were numerically modelled. In another numerical test, a double-notched sample, with fluid pressure in one notch while keeping the other one open to the atmosphere, is numerically extended to investigate how the fluid flow direction or the pore pressure gradient will influence the fracture behaviour. The simulation results show that fracture is strongly influenced by both pore pressure magnitude and pore pressure gradient. Keywords: seepage mechanics; heterogeneous; pore pressure; numerical simulation; failure process ZUSAMMENFASSUNG: Um den Einfluss der Wasserdruckgroesse der Oeffnung und der Porisitaet auf den Bruchentstanden und Verbreiten der Tension von Gebirgen zu beurteilen, wurde viele nummerische Pruefungen auf den hydraulischen Bruch in dem Gebirgen aufgenommen. Diese Pruefungen wurden mittels der Analyse- Software F-RFPA2D und Flow-stress-Damage Coupling model ( FSD) durchgefuehrt. Um den Einfluess der Wasserdruckgroesse der Oeffnung auf den Bruch zu beurteilen, wurden auch Bruchpruefung und nummerische Analogexperimenten gemacht, und dadurch wurde die ganze Phase der Bruchentstanden und Verbreiten wiedergezeigt, und die Ergebnissen ergeben sich, dass die Wasserdruckgroesse der Oeffnung und der Porisitaet sehr viel auf den Bruchentstanden und Verbreiten der Tension von Gebirgen beeinfluessen. Schluesselwoerter: Durchlaessigkeit , ungeleichmaessig, Wasserdruck der Oeffnung, nummerische Analog, Zerstoerungspahse Résumé : Une série de simulations numériques a été ménée pour analyser l’influence de la grandeur de la pression de pore et du gradient sur la naissance et la propagation des fractures de tensions par le biais de la simulation numérique des fractures hydroliques dans des rochers hétérogènes . Le logiciel F-RFPA (Rock Failure Process Analysis code ) intégrant FSD ( Flow-Stress-Damage coupling model ) y a été employé. Les résultats des simultations montrent tout le processus de la naissance et de la propagation des fractures sous la pression de pore. Ces résultats nous ont permis de constater que la grandeur de la pression de pore et le gradient exercent une influence importante sur la naissance des fractures dans les rochers et sur leur mode de propagation . Mots de clé : le mécanisme de transfusion ; l’hétéogénéité ; la pression de pore ; la simultation numérique ; le processus destructif

Jan 1, 2003

By Mike Ounpuu

"Locked cycle testing has become more common practice in the last 10 years. Reasons vary from a desire to avoid pilot plant testing, demand for more variability testing within deposits, and perhaps most importantly, a request from the financial institutions who invariably finance many of the projects. Surprisingly, many people don’t understand locked cycle testing, analysis and balancing. This paper provides a brief overview of locked cycle testing, and then progresses into a more detailed discussion on the analysis and balancing of locked cycle test data. The paper endeavors to educate CMP personnel on how to determine if the test was good and if a reasonable metallurgical projection was made. The paper uses case studies to illustrate the key points.INTRODUCTIONA locked cycle test is a repetitive batch used to simulate a continuous circuit. The basic procedure has a complete batch test performed in the first cycle which is then followed by similar batch tests which have “intermediate” material from the previous cycle added to the appropriate location in the current cycle. These batch tests, or cycles, are continued in this iterative manner for an arbitrary number of cycles. The final products from each cycle, i.e. final concentrate and final tailings, are filtered and thus removed from further processing. At the end of the test, all the products, final and intermediate, are dried, weighed and subjected to chemical analysis. The test is balanced and a metallurgical projection is made.This description can be found in many of our classical textbooks for the mineral engineer 1, 2, 3,4. Unfortunately, none of these textbooks provide any discussion beyond the basic procedure. Often, they provide comments such as in Taggart’ where he states; “It is questionable whether in any case it approximates mill results any more closely than the standard batch test”. It is truly surprising that our classic textbooks promote that locked cycle tests are more art than science, and suggest that they can be of dubious value. None of the textbooks provide meaningful insight or discussion in how to assess:"

Jan 1, 2001

A massive cobalt-containing pyrite orebody occurs in banded albite-quartz-biotite rocks at Thackaringa, some 30 km SW of Broken Hill. Because of the world-wide shortage of cobalt during the late 1970s, serious consideration was given to the development of a suitable flow-sheet to recover the cobalt from this ore. Details of a pressure leaching process in which more than 90 per cent of the cobalt is extracted from a pyrite concentrate are presented.

Jan 1, 1983

During the interval 1929-41, geophysical exploration in Russia made considerable progress, as reflected in publications. The greater part of these publications was available during the preparation of Geophysical Abstracts and Ms been abstracted in them. The rest was not received and remained unaccounted for. A considerable portion of these lading publications are now listed in bibliographic form, in view of their interest to geophysicists. All publications entered in the bibliography are in Russian. 1. GRAVITATIONAL METHODS 1. Abakelia, M. S. The Organization of Gravitational Observatories in Transcaucasia. Problemy Sovetskoi Geologi, Moscow, vol. 6, No. 5, 1936, pp. 452-454.

Jan 1, 1945

By Cordner G. D

Titanium is not yet being produced on a commercial scale despite the facts that it has some impressive properties, and that it occurs very abundantly in easily-mined, highgrade oxide ores. One important reason for this is that the excellent mechanical properties of the metal were not widely recognised and appreciated until about twenty years ago.Another factor which has tended to retard progress in titanium metallurgy has been the realization that the oxide minerals of titanium are very stable; in other words, considerable energy has to be expended to reduce the oxide to metal. Table 1 presents the minimum energies which would have to be expended to produce one ton of each of the metals, aluminium, magnesium, titanium and iron from their respective oxides under theoretically ideal conditions at normal temperature and pressure. At higher temperatures, the minimum energy requirements are different, but the values for the various metals still fall in the same order as indicated in Table 1.In actual fact, the energy consumption in the case of any particular metal is higher than the ideal value by an amount which can be determined only by' the results of plant practice. The only general conclusion that can be drawn from the data in Table 1 is that it might eventually prove...

Jan 1, 1950

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

By Khamis Y. Haramy

This paper summarizes ground control studies of longwall panel entry systems in two Western U.S. coal mines. Presented are comparisons of in situ pressure change measurements and assessments of chain pillar and entry behavior under a wide range of cover. Results indicate that no one entry system design is universally applicable, and that site-specific factors need to be considered for panel entry design. Relationships between overburden depth, face advance, and magnitude and location of the forward abutment are discussed for western operations. In addition, analysis indicates that use of yield pillars may reduce or eliminate some stress-related problems that plague longwall panel entry design.

Jan 1, 1989

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Feb 24, 1997

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009

Crocidolite deposits in the Hamersley Ranges, NW. of Western Australia, occur over a length of 180 miles and a width of 20' to 30 miles. Their stratigraphic environment and mineralogy is comparable to that of similar deposits of the Cape Belt, South Africa. It is probable that the known exposures' represent only a small portion of the total extent.Current production is wholly by Australian Blue Asbestos Pty. Ltd. at Wittenoom Gorge and has been in the order of 1,2,000 to 14,000 long t.p.a over the past six years.INTRODUCTIONThe Hamersley Ranges are located in the NW. Division of Western Australia and extend, approximately, from latitudes 21° 30' to 23°S and longitudes 117° to 1200 E. Their mean height above sea level is 2,000 ft, and they rise from 600 to 800 ft above the general level of the tableland which extends SE. from the coastal town of Roebourne.Mt. Bruce, the highest peak, is 4,024 ft above sea level. The ranges are intersected by numerous north-flowing streams, which are dry during the greater part of the year. These streams have carved deep gorges, and it is in these that the principal deposits of crocidolite outcrop.The presence of the mineral was first recorded in 1917, but the deposits remained untouched until 1937 when strong market demand for crocidolite resulted in considerable prospecting and mining activity, particularly in Yampire, Wittenoom and Dale's Gorges. It was established also that the blue asbestos belt extended from Willi Wolli Springs NW. to Millstream station, Le., over a length of 180 miles and a width of 20 to 30 miles. A number of attempts were made to develop and treat the Yampire and Wittenoom...

Jan 1, 1964

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By C. M. Campbell

THE dire effects of rapidly vanishing natural resources, widespread unemployment, and increased debt and taxation in recent years have challenged Canadians to produce a practical solution to these national economic problems. In more recent months, wars and rumours of war have indicated, among other things, the need for better control of our mineral wealth. The erection of a smelter on the lower mainland coast of British Columbia, treating all Western ores, and such ores as it will be found advisable to import, will make an important contribution toward a solution of these problems. It is believed that the ores tributary justify a smelter of major proportions. A stock-taking to confirm this can be made with reason-able accuracy in a short time, and this should be undertaken without delay. Enough general information is, however, available .in this paper to justify the technicians of the Department of Mines at Ottawa and of interested smelting companies making a preliminary study of the matter. THE DEFENCE ARGUMENT As a factor in rearmament, metals play a vital part. That rearmament is to continue on an increasing scale is indicated in Premier Chamberlain&apos;s address of October 3rd last, when he said: ?&apos;For a long period now we have been engaged in this country in a great programme of rearmament which is daily increasing in pace and volume. let no one think because we have signed &apos;this agreement between the four powers at Munich we can afford to relax our efforts or call a halt in our armaments at this moment&apos;. As matters stand, the facilities in British Columbia are entirely out of line with the strategic importance of this Province as the Western Front of Canada and the Empire. All our copper ores, and an appreciable part of our lead and zinc ores, are sent for treatment to Japan, United States, and Europe, while we import our iron and alloys. A treatment plant on this Coast would not only give us control of war metals and chemicals but it would provide an increased industrial and research population, badly needed in this area and of the greatest value in the case of war. This is where the mining industry can do its bit.

Jan 1, 1939

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

Magnetite cenospheres 40-270 I/m in diameter have been found during the combustion of pyrite concentrate.Micrographs of the surface and internal structures are presented together with comment on the mechanism of forrnation.The similarity to cenospheres found during the combustion of pulverized fuel was noted and speculation raised to their contribution to the dust and fume load in flash smelters.

Jan 1, 1980