Search Documents

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By Faan Bornman

"Reeves and Platt1 stated that dense medium separation is one of the most complex unit processes in mineral processing today particularly if cyclones are used. It is also the most efficient gravity concentrating process available to process engineers. The complexity of the process and large number of design and operating variables means that the process has largely remained more an art than a science. Dense medium separation is well established in the diamond, coal and iron ore industries but is gaining popularity as a pre-concentration step in other industries. The maintenance issues are addressed that will affect the efficiency of the operation.INTRODUCTION The purpose of the dense medium separation (DMS) process is to separate the valuable material from the waste based on gravity differences. However, the specific gravity difference between the two fractions must be large enough to achieve high efficiencies. Heavy particles sink through the dense liquid and light particles float. DMS is also used for the pre-concentration of minerals before further downstream processes like communition, in order to minimise the treatment costs. Examples are the pre-concentration of diamond ores or metalliferous ores like nickel, copper and cobalt. Dense medium separation is also used to upgrade the material to meet different market specifications, for example in coal and iron ore applications. A typical dense medium separation process for a diamond application is shown in Figure 1."

Jan 1, 2014

By S Smit, P J. J Strobo

ZINIFEX Century Mine is a zinc, lead and silver concentrate producer. Flotation is the primary method of minerals separation in this circuit. The flotation circuit is quite large with 79 flotation cells. The levels in each of these interconnected cells are controlled at more than 45 level control stations. Due to the multivariable interaction throughout the circuit, good level control was found to be difficult to achieve by just using normal Proportional-Integral-Derivative (PID) control. As a first step in advanced process control, the FloatStar Level Stabiliser, a multivariable controller developed specifically for flotation circuits, has been commissioned at Century mine to solve the level control problems. The first section of this paper therefore discusses and shows the results and improvements obtained by using the FloatStar level stabiliser. The results and benefits of the FloatStar Flow Optimiser are discussed in the second section of this paper.

Jan 1, 2004

By J. S. Roberts

"Campbell mines has been in operation since 1948. Part of the process consists of roasting of a flotation concentrate which contains arsenopyrite.At present operation level the milling rate averages about 850 t.p.d. and about 48 t.p.d. of concentrate is roasted. The gas emissions at present contain between 3 and 3.5 t.p.d. of arsenic trioxide, about2 - 2.5 t.p.d. of particulate matter and between 19 - 25 t.p.d. of sulphur dioxide. The particulate is extremely fine calcine dust and it assays about 4 oz. Of gold per ton.Until 1974 the gas was discharged untreated through a 125' stack.UntreatedThe decision was made in 1972 to erect a gas treatment plant, construction ran through 1973 and operation began in 1974. The cost of the installation was about 1.3 million dollars.On investigation the process technology, it was apparent that the plant operated by giant Yellowknife for the same purpose was the model we should study. I would like to acknowledge the fine cooperation we had from giant, the plant that emerged is very similar to theirs and incorporates some improvements suggested by them and based on their operating experience.The plant is designed to remove arsenic and solid dust and it has no provisions to remove sulphur dioxide.We depend upon the 125' stack to assure adequate dilution. Because of the nearby airport the stack cannot exceed 125'. A stack burner is provided that can ""y used to heat the stack gas and carry it higher into the atmosphere when there is an inversion condition.The removal of arsenic from hot gas is fairly simple. The sublimation point is about 425°f, a few degrees above this point the arsenic is a gas and a few degrees below it condenses into a solid form. The arsenic could have been removed by simply dropping the temperature below the condensation point and collecting all the solids in a baghouse. This would have removed the possibility of recovering the gold in the calcine dust and would have produced an impure and more bulky arsenic material to be placed in safe storage. The decision was made to collect the solid dust in a hot electrostatic precipitator operating above the sublimation point and subsequently lower the temperature below the condensation point and collect the arsenic in a baghouse."

Jan 1, 1976

By R. Chryst, R. Kus

In the Integrated IT Systems proposed by Przedsie? biorstwo Robót Geologiczno-Wiertniczych—Geological and Drilling Company (PRGW) a network connects a database with all of the departments of a mining division. A key element thereof is the common graphics environment—Micro Station supplied by the firm, Bentley. PRGW’s SoftMine software and GMSI’s CadsMine that are used to design and schedule mining operate in this environment. The digital form of the design project facilitates the verification of information and the integration of technical solutions with SAP R/3 type financial—accounting systems. The system has been successfully implemented in the Brown Coal Mine in Poland.

Jan 1, 2003

By Brad Gunn

Our program has been dictated by the necessity of broadening our markets through converting potash chemicals to fertilizers more in demand than potassium chloride. To this end, we have undertaken studies on methods of preparing potassium sulphate or potassium magnesium sulphate by rather simple conversion. When mixtures of sodium and magnesium sulphates are reacted with potassium chloride, the ratio of sodium to magnesium is quite pertinent. A range of ratios has been selected and the conversions of potassium chloride to sulphate have been assessed by cyclic operations. Results from experimental procedures for producing potassium nitrate are also avail-able. The influence on recovery for systems including organic solvents is assessed for a variety of situations.

Jan 1, 1971

By T. T. Chen, W. Petruk

The mineralogy of the feed, concentrates and tailings from the Heath Steele mill in New Brunswick was studied in detail to determine the liberation and recoveries of the major ore minerals, and to characterize the occurrence and distribution of the trace elements. The ore milled during August 1977 contained an average of 4.34 wt % Zn, 1.25 wt % Cu, 1.64 wt % Pb and 90 gr/ton Ag. The main trace elements in the ore are silver, cadmium, indium, cobalt, antimony, bismuth, arsenic, mercury, tin and gold. Silver is carried in solid solution in tetrahedrite-tennantlte, galena, Ag-Sb sulfosalts and Pb-Bi-Sb sulfosalts. Approximately half of the silver is recovered in the lead and copper concentrates and the remainder is lost in the tailings and Zn concentrate. As the major silver-bearing minerals also contain Sb and Bi, recovering silver by ore dressing would involve recovering elements that are troublesome in extraction metallurgy. Cadmium and most of the indium and mercury occur in solid solution in sphalerite and consequently are recovered in the zinc concentrate. Some indium is also recovered in the copper concentrate in a second unidentified indium-bearing mineral. Cobalt and arsenic occur principally in arsenopyrite, cobaltite, a Co-Fe sulfarsenide, pyrite and pyrrhotite, and follow these minerals into the tailings. Recovery of the valuable element cobalt, therefore, would involve recovering the environmentally hazardous element arsenic. Most of the tin and gold report to tailings. The ore was ground to about 80% minus 270 mesh. At this grind, 71 wt % of the sphalerite, 66 wt % of the chalcopyrite and 59 wt % of the galena were liberated. Recoveries of free sphalerite, free chalcopyrite and free galena in the Zn, Cu and Pb concentrates were 85 wt %, 76 wt % and 80 wt %, respectively; recoveries of unliberated sphalerite, unliberated chalcopyrite and unliberated galena in the respective Zn, Cu and Pb concentrates were 48 wt %, 5 wt % and 7 wt %. Some of the unliberated sphalerite and chalcopyrite grains in the tailings are large and would have been liberated at a finer grind.

Jan 1, 1980

By Jim Wickens, Vince Lofftus, Mark Kravetz

"This paper discusses how Bald Mountain Gold Mine (Ely, NV) dramatically reduced mercury production by treating process solutions with a liquid reagent based on organic sulfide chemistry. Cherokee Chemical Co. Inc. (Vernon, CA) markets this reagent as UNR 81 1A.A summary of the bench tests comparing various reagents is given. The ensuing plant trial is discussed and successful mercury removal results are presented. Data is presented to show that early removal of mercury in the process reduces the amount of mercury collected at retort. Data is also presented to show that use of this reagent does not reduce gold recovery. Plant trial treatment costs are discussed. Finally, the potential of this technology to substantially reduce closure costs as compared to traditional mercury removal options is discussed.INTRODUCTIONBald Mountain Mine produces gold. Mercury is a costly by-product of gold production because no revenue is generated from mercury. Traditionally, mercury leaches out with gold and follows the gold throughout the processing circuit until it is eventually condensed and collected at Retort. Minimizing or eliminating mercury production minimizes worker health and safety risks, minimizes environmental liability, and reduces costs. In the long term, minimizing mercury production will make mine closure easier and less costly.Bald Mountain Mine dramatically reduced mercury production by treating process solutions with liquid reagents called UNR 811 and UNR 811A. Several reagents were bench tested before proceeding with a plant trial. The reagent complexes the mercury to form an insoluble organic sulfide precipitate. In independent tests, the precipitate passed acid mobilization tests and is considered stable."

Jan 1, 2001

By R. B. Elver

The St Lawrence Seaway, a deep-water canal system between Montreal and Lake Ontario, was opened for navigation on April 25, 1959. Prior to the opening of the new Seaway, small boats known as canalers and a few deep-sea carriers, primarily from Norway since World War II, were the only ships able to journey past Montreal into Lake Ontario through the old Canadian St. Lawrence canal system. Thus it was necessary for many tons of bulk and general cargo to be shipped all-rail to and from Atlantic ports or to be transhipped to and from canalers. With the opening of the new Seaway, large Great Lakes bulk carriers and a much larger percentage of the world's shipping fleet are now able to sail directly from the sea to the heart of industrial North America. In this paper, the historical events leading up to the construction of the Seaway and the physical nature of the Great Lakes transportation system are briefly reviewed. Following this, an attempt is made to evaluate the effects of the new Seaway on Canada's mineral industry. Because the Seaway has been in operation for only one season, this paper must be considered only an interim report. Because of the importance of the Seaway to iron ore, this commodity will be dealt with in detail, although the effect on other mineral commodities such as coal, petroleum, nonferrous ores, iron and steel will be mentioned. At this time the author wishes to thank the various company and government officials who provided both factual information and critical opinions.

Jan 1, 1960

The development of an onboard contaminant diagnostic monitor to continuously measure contaminant level in a mining machine was advanced to a prototype stage in this contract. Several concepts were investigated and it was found that a static spool type sensor was the most reliable and accurate. Laboratory and field tests showed that an instrument based on this concept is capable of measuring contaminant levels and/or size distribution, depending on the configuration of the sensor. Moreover, this instrument can function on emulsions or homogeneous fluids. Current laboratory equipment can operate on homogeneous fluids only.

Jan 1, 1983

By G. L. Oldright, J. D. Sullivan, W. E. Keck

"An apparatus and procedure developed in the laboratory of the South-west Experiment Station of the Bureau of Mines are capable not only of determining the rate and volume of penetration of solutions into porous materials but also of determining the total volume of voids within particles of porous material, and the density. The method is applicable to ores, bricks, concretes, tiles, filter bottoms, or other porous materials of this nature. As will be made clear in the descriptive matter to follow, the method measures (a) the volume of voids within the porous materials and is not concerned with the interstitial space between the particles.Porous materials usually contain some large voids and also pores that are capillary in nature. To measure the total volume of voids in a sample it is necessary to replace the gas or gases within the voids with some liquid of known density. The large cavities can be filled quite readily, but under ordinary conditions a long time may be required to fill capillary pores. As many porous materials are of a decomposable nature it is necessary to evacuate the porous materials and then submerge them in a liquid of known density to bring about saturation in a short time. Then by the use of a hydrostatic balance the volume of porous material (solid itself) can be determined. To determine the volume of porous material plus voids it is necessary to coat the sample with some material, such s paraffin, which will prevent solution from entering the voids; then, by means of a hydrostatic balance, the volume of porous material plus voids is determined and by subtracting that of the porous material from this the volume of voids is ascertained. The rate of penetration of solutions can be determined either (a) by measuring the change in weight as the sample becomes saturated when immersed ni a liquid of know density, or (b) by measuring the volume of liquid penetrating with a dilatometer. In either instance, due to the fact that some penetration takes place as soon as the sample comes in contact with solution and before a reading can be taken, the sample must be paraffined to determine the total volume of penetration. Since many porous materials partly decompose and disintegrate in liquids the rate and volume of penetration can better be measured by dilatometer than by the change in weight, as saturation takes place when immersed in a liquid. The details of procedure for determining (a) total volume of voids, and (b) rate and volume of penetration are given in this paper."

Oct 1, 1930

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By Wolfgang Guetter, Wolfgang Weber

The upgrading project for two hydropower plants in Slovenia, Europe, requires two new pressure tunnels: Plave II (5.9 km Flysch) and Doblar II (3.6 km Limestone). It is the worldwide largest application of the Double-Shield TBM technology combined with an extremely thin-walled monoshell honeycomb lining system. The first drive has been completed by end of June 2000 achieving best performances of 50m/d and almost 1,100m/mth. In September 2000 the TBM started the second tunnel without any required adjustments due to geological or other reasons. Another 52m/d have been bored already within one production day of two 8 h shifts achieving a maximum penetration rate of more than 6m/h. The completion of the Doblar drive can be expected by February 2001.

Jan 1, 2001

By W. S. Steinberg

In 1963, the full-scale engineering study for the development of an iron, steel, and vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steelworks that produced steel and vanadium-bearing slag from a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for prereduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to open slag bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of the higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By S. R. Gilbert, C. O. Bounds, R. R. Ice

"Many ores are upgraded to produce auriferous sulphide concentrates (principally pyrite) which are not amenable to direct cyanidation. Often these refractory gold-bearing concentrates contain undesirable elements such as arsenic, antimony, etc., which present environmental and/or processing problems. The pretreatment techniques most often considered for processing these concentrates prior to cyanidation include roasting, pressure oxidation, chemical oxidation, pre-aeration, and recently, bacterial oxidation. In this paper, the technical performance and economics of bacterial pre-oxidation vs the classical roasting approach for treating a specific auriferous pyrite concentrate are compared. The results provide flow sheets, preliminary operating and capital cost estimates, and rates of return for the two processes and demonstrate the potential advantages of bacterial pre-oxidation. IntroductionThe increased attention that gold has received in the last ten years has prompted mining companies to look for lower grade orebodies. Many of these low-grade ores do not respond well to conventional direct cyanidation recovery techniques. As free-milling ores decline, gold is sought in refractory environments which, ultimately, drive up the treatment costs.There are a number of reasons for a gold ore to be termed refractory, most of which can be identified by thorough mineralogical examination. The mineralogical occurrence of gold can, to a great extent, impact the method by which the ore is treated and, consequently, the capital and operating costs. Gold in a refractory ore can often occur as discrete particles locked in a host of silicate or carbonate gangue, or associated with sulphides or sulphosalts. Depending on its particle size, gold can be liberated and recovered by mechanical size reduction such as regrinding. This approach is most effective for gold in the 10 - 50 micron range. Gold can also be associated with clay, iron hydroxides, or other minerals which tend to coat the gold surface and inhibit the penetration of the cyanide solution, resulting in poor plant recovery. Because of their resistance to cyanide dissolution, gold tellurides and other refractory gold minerals are also responsible for losses to the tailings. For these reasons, it is paramount that the mineralogical occurrence of the gold be thoroughly and accurately determined before selecting a final process flowsheet."

Jan 1, 1988

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By S. O. Bada

Fine phosphate feed is considered to be slime and normally disposed of as a discard in settling ponds or dumped as landfill. The purpose of this research was to establish whether commercially acceptable qualities and yields could be obtained from this material using dry separation methods. The results obtained from the electrostatic separation of <105 µm phosphate ore are presented. An existing separator was upgraded in order to improve on product and flotation concentrate recovery, to test different mineral, and to reduce particle residence time between the charging chamber and the separating zone of the separator. The operating conditions were varied according to the charges imparted to the particles in the electric field, and according to other device parameters. Parameters such as splitter position, charge reversal, rotation speed, charging voltage and separating voltage. The <105 µm phosphate feed was concentrated under both triboelectrification and inductive charging. The use of inductive charging and charge reversal resulted in a significant increase in grade for <105 µm phosphate feed, with the P2O5 grade increasing from about 12 per cent to 20.50 per cent, and a recovery of 26.30 per cent under a single stage of separation. It was found that better separation was achieved at rotation speed of 6000 r/min, -8 kV charging voltage, and 25 kV separating voltage.

Jan 1, 2012