Search Documents

The stability of parallel underground coal mine galleries and pillars have been investigated using two- and three-dimensional (3D) numerical stress analysis. Anisotropic horizontal in situ stresses and the direction of the excavations have been considered in the numerical analysis. The stability of the tunnels driven in a coal seam at various working depths has been investigated taking into account different strata conditions and then results from two- and three-dimensional numerical modelling studies were compared. Maximum principal stress components have been chosen in three various directions: vertical, parallel and perpendicular to the tunnel axis. Analysis have shown that in the anisotropic in situ stress field, the favourable direction of underground mine openings which have different strata conditions depend not only on the horizontal in situ stresses but also on the vertical in situ stresses. Furthermore, 3D numerical modelling studies have been carried out to investigate stability of multiple entry longwall panel gate roads and pillars with various width-to-length ratios (W/L). Results of the modelling studies have shown that the critical dimension of coal pillars depends on their width and the direction of maximum horizontal stresses.

Dec 6, 2010

By Rao P. K, Sahoo P. K

The main constituents of ferromanganese slags are silicates of Mn, Ca and AI. Factors affecting the recovery of manganese from a low manganese content ferromanganese slag (about 16 per cent MnO) during acid leaching were studied. These included time, temperature, agitation, sulphuric acid addition, solid:liquid ratio and particle size. Agitation rates greater than 300 rev/min. leaching periods greater than 30 min and temperatures above ambient were found to have no effect on Mn recovery. Dissolution of Mn was found to be highly dependent on the amount of acid added.About 90 per cent of the Mn was recovered when 5·5 times the stoichiometric amount of acid was used. About 28 per cent of the Mn was recovered when the stoichiometric quantity of acid (with respect to Mn alone) was used. However, the recovery increased to about 75 per cent when the total stoichiometric requirement of acid with respect to Ca, Al, Mg and Fe as well as Mn was used for leaching. The extent of Mn dissolution also depended on the particle size of the slag. The percentage of Mn recovery (using 5·5 times the stoichiometric amount of acid) increased from about 60 per cent to about 92 per cent when particle size decreased from -36 +52 to -150 +200 mesh (B.S.S.). When the results of this study were compared with those in a previous study involv,ing the leaching of a high manganese content slag (containing about 40 per cent MnO) results were similar except that there was a gr-eater consumption of acid in the present case (i.e. low manganese content slag).

Jan 1, 1979

By Joseph A. Holmes

The investigations carried on at the fuel-testing plant of the United States Geological Survey at St. Louis in 1904-1907 included tests of the steaming and gas-producing qualities of many coals and of the possibilif3 of their improvement by briquetting, together with washing and coking tests and tests of some of the resulting coke in the cupola. These tests were part of a general inquiry into the manner of utilizing most efficiently each of the coals under investigation. The equipment used in the cupola tests of coke, the manner of conducting the tests, and the essential results have been described in publications of the Geological Survey," and only the more important conclusions to be drawn from the tests are mentioned in the following pages. The tests were made to show the fitness of the cokes for foundry purposes, but an incidentlll result was to show foundry men and the coke producers the advisability of studying the conditions of foundry practice. The present bulletin, published by the Bureau of Mines because the analyzing and testing of fuels have been transferred from the Gilological Survey to the Bureau of Mines, briefly reviews the status of the coke industry, some features of practice in the use of coke in the foundry, the probable happenings of a cupola heat, and the reasons for modifying charging practice so that a particular coke can be used to best advantage.

Jan 1, 1910

By W. L. Garrison

Improvements continue to be made in rapid excavation and tunneling technology. There are several ways to examine the impacts of such improvements. The most common procedure is to monitor current developments and to evaluate prospects for expansion of present types of uses. Other approaches are called for, however, if the technology might be used in ways not now imagined, if the search is for information for managers of technology development, and if the issue is that of the wise use of the technology by society. The first section of the paper will pose these matters as questions. These questions will be examined from the point of view of the processes of technology development and utilization, and then further examined against the backdrop of processes at work within the urban area. Such an examination will provide insight into the way technology developments should proceed. The final section will present some comments that may be useful to those guiding the development of the technology and to those who might provide leadership for its wise utilization. THE QUESTIONS Three questions are posed: 1. Are there uses for the technology beyond further penetrations of its present markets? 2. Can information be supplied to managers of technology development so that they may improve the assignment of priorities among development choices? 3. How can society make wiser use of the technology?

Jan 1, 1974

Computer applications are ideally suited to the day to day operations of grade control and short term planning on a mine site. By refining this part of the operation there is scope to increase profits by more accurately predicting ore grade and tonnage, and allowing the mining engineer more flexibility in his approach to scheduling. Large numbers of blasthole or ditchwitch samples need to be processed in a fast and efficient manner, and stored in a database for future reference. The mining engineer has to calculate tonnages and subdivide the blast or digging area into mineable areas of waste, low and high grade ore. New grade and tonnage information must be used by the mining engineer to update his short term plan. Answers must be obtained quickly and efficiently, but a high level of individual input is necessary in order that maximum use is made of the information. Geostatistical analysis of samples can be used to refine the interpolation techniques. Reconciliation between the original grade model, the newly sampled area, and the final product should be monitored continually.

Jan 1, 1989

By Met B. E

During the operation of the Parkes process of desilverising, and in the earlier days of the continuous process, gold and silver were removed separately from softened lead bullion. Gold was removed in the Parkes process by a selective zincing, and -in the continuous process by treatment with zinc in a special de-golding kettle, in each case a crust being obtained carrying the gold and a small portion of the silver. Actually the process could have been more correctly termed a de-copperising process, on accountof the relatively large amount of this metal present, and its affinity for zinc, which caused it to enter the crusts produced.The crust was treated in reverberatory furnaces, where the bulk of the copper and zinc was removed in by-products, and the resulting "gold bullion" cupelled to give adore bullion containing approximately 2,000 ounces gold per ton.For the purpose of parting this dore, a small Balbach-Thum plant of 11 cells was used, and once each six months a short campaign was conducted on the accumulated metal.With the development of the process of de-copperising smelter bullion by means of sulphur, when a bullion averaging about .004% copper was constantly available for refining, the need for a separate de-golding process disappeared.The de-golding kettle of the Continuous Process...

Jan 1, 1937

By D. Fenn, A. du Kanda, D. Dukhan

"SynopsisGibb Consulting Services was contracted by Eskom Line Engineering Services to conduct an investigation to determine the absolute displacement to date and infer the current rate of displacement of unsurveyed colliery backfill.At the test site, where a 400 kV power line is to be constructed, neither the surface nor the backfill material had been monitored and it was not possible to state whether the surface will be subject to future settlement that may compromise surface infrastructure. Therefore indirect methods of estimating current and future displacements needed to be found to act as a proxy for a comprehensive long-term settlement monitoring exercise and provide a reasonable estimate for the settlement that has occurred in the decades of mining.The innovative solution was to recover essentially undisturbed core from backfill using a sonic drill rig and use the measured dry density values from the samples as a proxy for the rate and absolute displacement in the backfill.The success in obtaining an essentially undisturbed backfill core and the clear relationship of the backfill density with age and depth allowed the conclusion to be issued that the power line infrastructure can be constructed over the backfill; with a warning that once the water table recovers after mining ceases some collapse settlement may occur.With this method, the amount of settlement can be predicted and, if proven conclusively, provides a way to confidently release huge areas of currently waste ground for future surface infrastructural development.IntroductionIn coal mining, it is normal mining practice to backfill the newly mined-out voids with the excavated waste rock and soils. As there is no requirement for the mining companies to uniformly compact the spoil or accurately monitor surface or inter-backfill displacement, these backfilled voids are prone to differential compaction and consolidation settlement. They are therefore avoided as sites for future surface infrastructure work, especially for linear structures such as roads, railways, and power lines."

Jan 1, 2015

By J. A. McLennan, J. M. Ortiz

Nickel laterite deposits are typically formed from tropically weathered mafic-to-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs) or representative dozer regions (RDRs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate “optimum” RDR mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each RDR. The optimum mining elevation is the elevation where the lowest summed cost of “accepting dilution” and “wasting ore” occurs. The reported RDR dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation. The reported RDR lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum RDR mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Jan 1, 2006

By P. K. Das, S. K. Singh, C. C. Chang, E. C. Wang, R. B. Roberts

As part of the New York City’s redevelopment of the far west side of mid-town Manhattan, this project will add 1.5 miles of twin bored tunnel to No. 7 Subway Line. The proposed alignment extending from the Times Square Station west beneath 41stStreet turning south under Eleventh Avenue and terminating at 25th Street will include two new stations. The tunnels and station caverns will be primarily constructed in the Manhattan Schist, and will pass in close proximity to several major overly ingstructures. This paper discusses the lithology and structural discontinuities of rockmass along the project alignment, tunnel and cavern rock loading, groundwater hydrology, groundwater quality, groundwater treatment and sustainable design.

Jan 1, 2005

By Joe Maher

[ ]

Jan 1, 1976

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By L. Rademan

The kinetic leaching behaviour of a low-grade surface gold ore and a high-grade reef ore were evaluated to determine the achievable gold recovery from these ores and particularly mixtures of these ores. The reef ore material has a head grade of 13.40 g/t with a relative standard deviation of 3%, and the unprocessed surface ore material a head grade of 0.43 g/t with a relative standard deviation of 15.6%. It is concluded that the kinetic leaching behaviour of these free milling gold ores during cyanidation, is not influenced by mixing of reef and surface ore material. No statistically significant relationship exists between the achievable recovery by direct cyanidation and the head grade of the material fed. No ideal ratio of surface ore to reef ore could be established. It is recommended that these materials should be processed simultaneously to minimize the costs, security risks, and losses incurred in transportation.

Jan 1, 2012

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

By David Ziegler, John Babcock, Gregory Poole

On December 9, 2003 at 3:59 PM EST an earthquake with a 4.5 magnitude occurred in central Virginia. According to a survey on the US Geological Survey website, this quake was felt as far away as Bridgeton Missouri, approximately 683 mile from the epicenter1. We recorded the vibrations from this earthquake on 14 seismographs that were set up for monitoring vibrations from blasting activities in the area. Having this data gave us an opportunity to compare earthquake and blasting vibrations. The amplitudes, frequencies and duration were much different than vibrations from mining and construction blasting. A common question we get from homeowners when discussing vibrations from blasting activities is “How does that compare to the Richter scale?” The goal of this report is to provide some simple answers for that question. The Richter and Mercalli scale are compared to the particle velocities in order to show their relationship.

Jan 1, 2005

By Xinzhi Du

Coal strength is essential to analyze the stability of excavation in coal. It is well known that the strength of coal tested in the laboratory is size-dependent, and different size specimens will produce different strength. Many researchers have studied the uniaxial compressive strength of coal and developed a number of empirical formulae to describe the strength variation with specimen size. According to a comprehensive data base that includes most of the laboratory testing results in the last century in U.S. and South Africa, the size effect and shape effect were reviewed and analyzed. The results show that different groups of coal specimens have different size effect on the compressive strength. The critical size for the size effect from the data analysis is about 40 in. The shape (W/H) of the specimens has a large effect on the compressive strength. The pillar strength formulae obtained from the data regression have a larger strength than all other existing formulae. Most pillar strength formulae have their own place in coal pillar design field. In order to analyze the difference of those formulae, twelve design formulae have been selected to compare using the Pittsburgh coal seam. The intention is not to determine the preferred formulae, but only to compare them, and see how do the W/H ratio, width, length, angle, cross-section area and effective width affect different pillar strength formulae?

Jan 1, 2008

By Juan Antonio Huamán Fernández

De acuerdo al estudio que realizó la Dirección General de Minería del Ministerio de Energía y Minas en el Perú, las estadísticas de accidentes fatales reportadas a escala nacional en el 2002 indican que la mayoría de accidentes fatales ocurridos en mina subterránea corresponden al 40% de desprendimientos de roca. Por lo cual, las empresas mineras preveen un programa basado en el desarrollo de la técnica de Gestión de Riesgos, que les permita un control en la seguridad del proceso. En este sentido, el presente texto desarrolla una técnica que identifica los diferentes factores que intervienen en los riesgos principales a través de los riesgos asociados; es decir, cuáles son esos riesgos asociados que influyen negativamente en cada una de las tareas que puedan causar accidentes.

Jul 31, 2003

By Roy M. Schnabel

The Fashion Island Boulevard Bridge over the Marina Lagoon in San Mateo, California is an eight span precast, prestressed concrete girder bridge. It is approximately 495 feet in length and 61 feet in width. It is supported on 36" diameter octagonal, hollow precast-prestressed concrete pile columns. The bridge was constructed in 1968 and suffered considerable damage during the Loma Prieta Earthquake in 1989. A damage survey report prepared by the State's Office of Emergency Services (OES) recorded that sixteen of the twenty-one pile-columns sustained heavy to moderate damage from the Loma Prieta Earthquake. The damage consisted of cracking and spalling at the tops of the pile-columns. Spalls at the most heavily damaged columns exposed the prestressing strands and confinement reinforcing which also showed signs of corrosion.

Jan 1, 1993

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By P. Fauvel, V. Nasri

In January 2001, French and Italian governments signed an agreement for the construction of a new Lyon-Turin railway line. This project includes a tunnel of 53.1 km length and a maximum of 2500 m overburden to be designed for a reference speed of220 km/h. The tunnel crosses major part of the West Alpine geological formations, which are very complex and contrasted in terms of the nature of rocks and the mechanical and hydrogeological conditions. In addition to the twin single-track tubes, numerous intermediary shafts, security station and intervention sites and cross passages should be built to respond to the security, operational and construction requirements. This paper describes the results of the preliminary engineering design and multiple challenges of this very long and deep railway tunnel.

Jan 1, 2005

By L. G. Marshall

Gypsum mining and processing has been one of the principal industries in Iowa for more than 75 years. For most of that period, Iowa has ranked among the five leading States in the production of crude gypsum and of calcined-gypsum products. The Fort Dodge area accounted for 11 percent of the gypsum products produced in the United States in 1956. Before 1927 the output by the major companies came from underground operations, using a room-and-pillar stoping method. At present, all production comes from quarries. The quarry methods at the various properties are similar. This paper describes the quarrying, methods employed in the district and the type of equipment used by each company. The sections on history and geology are, in part abstracts from State annual reports and an Iowa Geological Survey publication.3/

Jan 1, 1959