Search Documents

By R. A. Lord, H. M. Prichard

efficiency is discussed from both experimental and

Apr 1, 1994

By Sudhir Kumar Kashyap

In underground activities ground control is a challenging problem. It affects safety, production, and efficiency. As per statistics of accident data, ?fall of roof/sides? is one of the major causes of mine accidents. In many cases, our experiences and understanding of soil and rock behavior still fall short of being able to predict how the ground will behave. Presently, empirical approaches to design are widely used in estimating mine support parameters. Under these circumstances, expert judgment plays an important role, and such accidents can be obviated with accurate measurement and optimization of data and analysis using the neuro-fuzzy technique of artificial intelligence. Recently, a neuro-fuzzy hybrid approach has become one of the major areas of interest in engineering fields because it gets the benefits of neural networks as well as those of fuzzy logic systems, and it removes the individual disadvantages by combining them on the common features. Neural network and fuzzy logic technologies have common features, such as a distributed representation of knowledge, the ability to handle data with uncertainty and imprecision, etc., like in ground control. Fuzzy logic technique has tolerance for imprecision of data, while neural networks have tolerance for noisy data. In this paper we have focused an intelligent technique, i.e., neuro-fuzzy technique, to approximate the setting load given to the standing support (props) erected for the purpose of supporting freshly exposed roof during underground mining. We have used twelve input variables of rock parameters, and after having trained using a neural network with a sigmoidal function as an activation function, simulation was done to find the output parameter, i.e., the pre-load (setting load)to be applied on props. Outputs of the neural network were again fed to the fuzzy system together with the twelve parameters, incorporating five triangular membership functions for each parameter. Final optimum output was approximated using the MATLAB program, which was found to be satisfactory. Neuro-fuzzy technique has better performance over individual neural networks or fuzzy logic technique.

Jan 1, 2012

By Syd S. Peng

Mountaintop removal (MTR) mining started in West Virginia nearly 30 years ago. This surface mining method can extract multiple coal seams as thin as a few inches in whole and minimum rock dilution in very steep mountainous terrain. MTR is highly efficient, even if coal seams are in close proximity and small in a real extent. Consequently, MTR has been widely used in the Central Appalachian coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impact on the surrounding area. During the past two years, however, the debate over MTR mining has grown quickly and has become very intense. This article describes chronologically issues raised by various parties, legal actions, impacts on mining permit applications and research projects developed to address the issues.

Jan 1, 2000

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By B Taylor

Although the underground mining environment is arguably safer now than at any time in history, as underground mining operations across the globe increase in-depth, magnitude, and complexity, protecting workers from harm becomes increasingly challenging. In deep, stressed, seismic mines the development face is one of the most hazardous work areas. The active face is usually the furthest extent of the underground workings, so ventilation can be difficult to maintain, exposing workers to high temperature and humidity while working on foot and doing manual labour. While mechanisation has made many tasks easier in modern times, the reality of underground mining is that development charge-up workers still spend long periods directly exposed hazards at the face. In 2019, Orica and Epiroc partnered to co-develop the world’s first fully mechanised development charging unit using fully wireless initiation, called Avatel™. Built on Epiroc’s M2 Boomer carrier platform, the system is designed to allow one person to charge a development face from the safety of a fully enclosed cabin, thereby reducing exposure to hazards at the face. The system was prototyped in Europe before entering commercial introduction in 2022. This paper reviews earlier attempts to mechanise underground charge-up and describes the development journey and engineering challenges of building a mechanised development charging machine.

Mar 29, 2023

Effective gas management in coal mines, as well as proper ventilation design, is very important for maintaining the safety of underground coal miners. Advances in numerical modeling techniques have enabled evaluations of the coal mining environment using advanced grid designs and computed gas distributions through detailed mathematical models. These models help engineers to see the unseen areas of the mine through visualization of the data and ultimately help improve worker safety. This paper summarizes the modeling efforts conducted by NIOSH in the U.S. and CSIRO in Australia to address various gas management issues encountered in longwall mines. The modeling studies involved two of the most widely used grid-based techniques, namely computational fluid dynamics (CFD) and numerical reservoir modeling. This paper discusses the application of these techniques for gob inertization and gas control for spontaneous combustion, pre-mining degasification of coalbeds, gob gas venthole design and performance evaluation in longwalls, and gas management during development mining.

Jan 1, 2009

By Thomas D. Kelly

In 1900, the average U.S. citizen’s average life span was 47 years. He traveled about 1,900 km (1,200miles) in a lifetime and resided in a home with an ice-box for food storage and oil or gas for lighting. He communicated by mail, telegraph and crude telephones with limited availability and range. By 2000, the average citizen’s life span was 77 years. He traveled an average of 19,000 km/a (12,000 miles/year) by automobile alone. He resided in a home with many electrical appliances, including refrigerators and electric lights. And he communicated almost instantaneously with any other part of the globe by several widely available means, including portable phones and e-mail.

Jan 1, 2002

By Ray Brainard

The Jollyville Transmission Main will be a 10.5-km- (6.5-mile)-long, 213-cm (84-in.) diameter rock tunnel. The tunnel will pass beneath the Balcones Canyonlands Preserve, which was established to protect two endangered bird species, six endangered cave invertebrates and a threatened salamander. To address the sensitive habitat that the transmission main is to pass through, the city of Austin developed an environmental commissioning (EC) process that brought together environmental engineers and scientists, the city?s project management team and the designer team to work collaboratively to meet the city?s goals of producing a cost-effective design while also protecting the environment. This paper describes the environmental commissioning process and the benefits it brought to the project and environment through some unique environmental mitigation measures to protect this sensitive area.

Jan 1, 2012

By Mao Bai

In predicting the integrity of under-mined structures, surface horizontal displacements and curvatures are frequently of greater importance than the more homogeneous vertical displacements. Accurate evaluation of mining induced subsidence and horizontal displacement further requires that the predictive model adequately represents the subsurface geology, mining geometry and extraction sequencing. The following documents an extension of the Subsidence Prediction and System Identification method (SPASID) to the evaluation of horizontal strains. Comparisons are made between predictions from SPASID and two other empirical methods against measured data from a case study. The system identification method is illustrated to predict horizontal displacements and strains most consistently with the in situ data.

Jan 1, 1989

By A. T. Iannacchione

From 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig.1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig. 2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91%, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from1990 to 1996. This number is not large in magnitude. But a workforce of fewer than 2,000 miners makes for a high fatal-accident rate. The severity of the typical fall-of-ground injury is, in general, very high. About three-fifths of all roof, face and rib fall injuries were designated by the US Mine Safety and Health Administration (MSHA) as some kind of lost time accident. MSHA assigns each accident a severity value from one to six. A one represents a fatality, a two, a permanent disability and three, a lost time accident (Fig. 3).

Jan 1, 2000

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By A Priatna, H Rumbino, T Casten

This paper discusses the progress of the Deep Mill Level Zone (DMLZ) mine from the pre-feasibility study completed in 2005, through commencement of development access in 2008, completion of the feasibility in 2010 and cave initiation in late 2015. This fourth lift of caving in the East Ertsberg Skarn System (EESS) is located 500 m below the currently producing Deep Ore Zone (DOZ) mine and represents approximately half a billion tonnes of ore and around 1900 planned drawpoints, scheduled to be mined at a peak of 80 000 t/d.The paper reviews the mine design, access requirements, planned footprint sequence and major fixed facility installations such as ventilation, oreflow and shops. A discussion of the preproduction development and construction activities and some of the critical technical challenges overcome during this time frame are addressed, as well as the cave initiation process undertaken in late 2015 and the ramp-up of production and progression of caving.CITATION:Casten, T, Priatna, A and Rumbino, H, 2016. Deep Mill Level Zone – from feasibility to production, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By B. E. Warren

Jan 1, 1965

By Bruce D. Hansen

For many years, Newmont has focused on improving its operations. After the merger between Newmont and Santa Fe Pacific Gold, Newmont created synergies of more than $50 million a year in Nevada. This was done primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. At its mine facilities in Nevada, Newmont has used a combination of several strategies to decrease the costs of operations and to increase profitability. These include computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and several available metallurgical processing options.

Jan 1, 1999

By M. K. Larson

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment, and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. But this efficiency also comes at a cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impacts of underlying assumptions in each method is essential to proper use of results in mine design. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health

Jan 1, 2009

By A. J. Lynch

Mineral processing models have been discussed for many years but it was not until digital computers became available about 1960 that serious attempts at circuit simulation could be carried out. Even then the work was primarily academic until PCs could be used by engineers in plants and design offices in the mid-1980s. Since then simulation has moved quickly and it is now at the point that most processes can be simulated reasonably accurately for purposes of design and optimization. There are still some significant deficiencies, notably in dry grinding and separation, and in the chemical interactions in flotation. Future work will involve: ?improvements of existing models ?dynamic simulation for automatic control and, in particular ,for training which is a weak link ?using advanced simulation models to predict liberation and separation from data acquired from SEM-based liberation analysers. Eventually mineral processes models will be part of total simulation systems which will incorporate mining and downstream processes including all environmental impacts.

Jan 1, 1999

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010

By Oliver Bowles

ROCK is no doubt the most abundant of all material things because the planet on which we live is made of it. All animal and vegetable organisms and the multitude of natural and manufactured products that occupy a comparatively insignificant film on the outer surface of the planet are derived from rock. Processes of Nature acting for untold centuries have transformed rock into soil, making possible the development of vegetable and annual life; and rocks have supplied the numerous raw materials, metallic and nonmetallic, wherewith the innumerable appurtenances of a complex civilization have been fabricated. As time goes on we live with increasing speed and with enlarged desires. Time and space are shortened by man's ingenuity, and products for human use must be manufactured with greater and greater celerity. It was inevitable that Nature's slow processes of rock alteration should fail to keep pace with human demands and that the variety of natural products should fall far short of the requirements of an industrial age. Man therefore supplemented these processes by attacking rock in its native bed amid using it to supply needs not otherwise satisfied.

Jan 1, 1934

By Rüdiger Wunsch

The new high speed Vienna - St.Pölten line and the Lainzer tunnel are to be connected to the existing Western railway line in Vienna. This involves building an underground cut and cover branching tunnel which will be connected to the Western railway line by ramps. A key structure is the Herzmansky Street tunnel, which has a length of some 820m. It is to be constructed as a cut and cover tunnel using the top down method. The walls of the tunnel are designed as a water resistant structure consisting of double walls, an outer wall of bored piles and an inner reinforced concrete wall. The bored pile wall will be used as a temporary retaining wall during the construction phase and will also be a structural part of the per­manent tunnel wall. The retaining walls of the open pit, which will have a depth of up to 14m and a width of 12m, were investigated as a non-contiguous bored pile wall and overlapped bored pile wall. Preventing ground water from penetrating into the pit is of paramount importance. The high ground wa­ter level is the determining factor for the dimensioning of the bored pile wall and results in the require­ment for a water resistant concrete structure. It has been necessary to adopt adequate measures, therefore, in order to reduce the hydrostatic water pressure during the construction phase, assuming economical pile dimensions.

Jan 1, 2000