Search Documents

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By R. J. Anderson, A. V. Castelli

In 1986, United States' barite production fell 48.9%, consumption - sold or used by grinding plants - was off 47.3%, and imports were down 63.8%. Meanwhile, world mine production decreased 29.6%, according to the US Bureau of Mines. However, value of US-produced barite FOB mine increased 46.51%, according to USBM figures. The declared value CIF US port of all imported unground barite decreased from $41.94/t ($46.23 per st) to $39.02/t ($43.01 per st). Nevada continued to be the leading US producer of barite with 69% of the total. It is followed by Georgia, Missouri, Tennessee, and California. The USBM estimates that 65% of the barite mined was used as a weighting agent in drilling fluids. The remaining 35% was used in the production of barium chemicals and as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector made up a larger percentage of the US produced barite in 1987 than it did in 1986, increasing the overall value per ton of barite. Barite consumption was at its lowest since 1963. It is estimated that 80% of the barite was consumed in the drilling fluid market. The remaining 20% was used in barium chemicals, glass, and as filler in plastics and paper. The decline of barite used in drilling fluid followed the decline in the average number rotary rigs operating - 964 versus 1968 in 1985. This was the lowest average number of rotary rigs operating since 1971. The non-oilfield market was up 5.3% in 1986. This increase can be attributed to the increased use as a filler in plastics. Imports of crude barite, though down nearly two-thirds, still made up 65% of the barite consumed in the US. China was the leading exporter to the US with 58%, followed by India, 15.4%; Morocco, 11%; Thailand, 5.4%; Mexico, 4.6%; Chile, 3.9%; and Ireland, 1.7%. Less than 1% of the imported ore was used in the nonoilfield sector. Imports of ground barite dropped from 64.4 kt (71,000 st) to 19.8 kt (21,800 st) in 1986. Of this amount, 14.1 kt (15,500 st) were used in drilling fluids in 1986 and the remainder for non-oilfield use. During 1986, more of the grinding plants supplying the drilling fluid market were closed. Dresser Magcobar and IMCO Services, a Halliburton company, formed M-I Drilling Fluids Co. Mine production in the US will probably decrease in 1987 due to the lower cost of imported ore. No significant change is expected in the drilling fluid market. The average number of operating rotary rigs is estimated at 950 in 1987 versus 965 in 1986. The nondrilling fluid markets (chemicals, glass, and filler) will follow the overall US economy. Bauxite and alumina R. J. Anderson, Ohio State University US bauxite production in 1986 dropped to a pre-World War II level, continuing a decline that began a decade ago. 1986 production totaled 450 kt (496,000 st), compared to 674 kt (743,000 st) in 1985. World production of bauxite also decreased in 1986. This reflected the soft market in alumina, aluminum, and related products. Total mine production worldwide came to 79 Mt (87 million st), down from 85 Mt (94 million st) in 1985. For the sixteenth consecutive year, Australian production of bauxite led all other sources. No other country approached the 28 Mt (31 million st) mined in Australia in 1986, despite a 4.4-Mt (4.9-million st) drop in its output from 1985. Other major producers in 1986 were: Guinea 11 Mt (12 million st), Brazil, 6.5 Mt (7 million st), Jamaica, 6.5 Mt (7 million st), and Suriname 2.8 Mt (3 million st). Despite weakness in world demand for bauxite, Venezuela, heretofore an alumina producer, is now pushing development of a new mining venture near the western border of the state of Bolivar. Plans call for barging bauxite down the Orinoco River to the Ciudad Guyana alumina plant, a distance of 650 km (400 miles).

Jan 5, 1987

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump's best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

By Robert Martin, Brian W. Stump, David P. Anderson

2We use field measurements to quantify physical processes that accompany different types of mining explosions. The data sets collected include three-component ground motion, acoustic, video and high speed film, three dimensional topography, geological and geophysical properties, design blast pattern and timing, and velocity of detonation in the explosive for individual borehole detonation times. The explosions include simple single-fired contained explosions, ones designed to bulk and fracture material and those that cast material. Our goal is a physical understanding of these sources for the purposes of optimizing blasting practices.

Jan 1, 1998

By M. W. Hildyard

The aim of this paper is to demonstrate that active seismic measurements could have an impact in helping solve rock engineering problems experienced in the South African mining industry. The paper presents a variety of experimental and numerical results where seismic waves show clear differences in wave-speed and amplitudes due to different degrees of fracturing. It presents results from the ?Omnibus? project commissioned to develop new ultrasonic technologies for diagnosing fracturing for nuclear waste repositories. This included using models to investigate assemblies of cracks where the effects of crack density and crack size on waveforms are shown to be coupled. Results indicate that these effects can be decoupled in the frequency domain, where the Fourier amplitude aids in estimating crack size, while the low frequency phase-difference has a direct relationship to crack density. Models are also shown to aid interpretation of waveforms by isolating geometric effects from the effects due to cracks. Two rock engineering problems experienced in the South African mining industry are investigated through numerical examples. These demonstrate that determining whether ?crush? pillars have failed and determining the degree of fracturing in the hangingwall of stopes, may be possible through the use of active seismic surveys.

Jan 1, 2005

By Stephen P. Quin

One of the most prospective undeveloped greenstone belts in Canada, the Hope Bay greenstone belt extends over 80km in a north-south direction and is between 7 and 20km wide. The belt lies on the arctic coast and comprises mafic meta-volcanic and meta-sedimentary rocks that are bounded by Archean granite intrusives and gneisses. The greenstone package has been deformed during multiple events and is transected by major northsouth trending shear zones that appear to exert a significant control on the localization of mineralization. The Hope Bay belt contains a number of significant gold deposits hosted in a typical Archean greenstone belt and which occur in several geologic settings, including shear-hosted, lode-style and breccia-associated. Combined, the deposits host a measured and indicated resource of 1.6 million oz of gold averaging 15.7 g/t plus an inferred resource of 2.7 million oz of gold averaging 12.3 g/t. All deposits remain open to expansion. Exploration in the period 2000-2002 by Miramar includes more than 110,000m of drilling to more fully define the nature of the known deposits, while regional exploration has focused on identifying and evaluating new targets. In carrying out its programs, Miramar uses a number of techniques to improve its chances of exploration success. Activity in 2003 includes 43,000m of drilling focused on expanding resources in the Madrid area, testing the Boston deposit at depth and continuing the hunt for more discoveries. Meanwhile Miramar is advancing one of the deposits towards a production decision, based on a low capital, high return development scenario.

May 1, 2003

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA), San Bernardino County, California During field work, BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1,188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) full access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion, $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By Steven C. Borell

For more than a decade, changes have occurred each year that have improved the regulatory and business climate for mining in Alaska. These changes have taken place during Republican and Democratic governorships as well as when the state House of Representatives and Senate were controlled by either party. During some years, the changes have been relatively minor. In others, including the 2003 legislative session, the changes could only be characterized as massive. These improvements have encouraged exploration. This, in turn, has resulted in some major new discoveries. But Alaska is essentially unexplored and tremendous opportunities remain.

Jan 1, 2004

By P. Keating, J. Goutier, J. Ayer

"New, high-resolution geophysical surveys were undertaken over parts of the Abitibi Subprovince, Canada, to help with geological mapping and to promote mineral exploration. Gravity surveys in the Rouyn-Noranda and Matagami areas (Québec) allowed better 3-D mapping of important geological structures, and a multiscale edge analysis of ground gravity data over the Blake River Group confirms that major faults behave at depth as predicted by surface geology. Airborne gravimetry west of Matagami (Québec) helped to identify a new trend south of Lake Grasset that is almost perpendicular to the assumed geological trend of the area. Electromagnetic (EM) surveys, flown in the Chibougamau (Québec) and Bartlett Dome (Ontario) areas, allowed new conductors to be identified at greater depths than were achievable with previously used EM systems. Airborne magnetic surveys were flown in the Burntbush area (Ontario), and other available high-resolution magnetic data were compiled to produce a continuous and homogenous magnetic grid of the Abitibi region.The resulting compilation map clearly shows the locations of dikes, faults, and shears zones, and reveals some fault extensions in areas of extensive overburden. This grid also allows the computation of enhanced maps, such as vertical derivative and tilt maps (e.g., a tilt map shows subtle magnetic features in the Blake River Group that are difficult to see in the total magnetic field or its first derivative). Results from these new surveys show there is considerable value in (1) resurveying areas covered by older surveys, and (2) recompiling data sets from these older surveys."

Jan 1, 2012

By D I. Cliff

The loss of 11 miners in the 7 August 1994 Moura No.2 Underground Mine Disaster was the catalyst for major change in the way safety was managed in the Australian Mining Industry. The impact was felt across all sectors not just underground coal. It was the catalyst for the overhaul of the regulatory frameworks, moving away from prescription to management systems and risk management. This had a substantial impact on the way not only the industry operated but also on how the regulator functioned. It heralded the introduction of competency-based training across all levels of the mining workforce. Since that time major improvements in safety performance have occurred. However, hiding within the statistics are some disturbing trends. This paper aims to analyse the progress made in the past 30 years and identify the current and emerging issues. Automation is bringing major production and safety benefits, but at the same time other factors such as the reduction in workforce numbers and ever-increasing production pressures are leading to high turnover rates. This in turn causes to a loss of experience and expertise. In addition, and of particular importance, is the recognition of psychosocial wellness on workforce safety. Many of these factors are not unique to the mining industry however they may be exacerbated by the scale of mining, the remoteness of the mines and family unfriendly mining rosters.

Apr 16, 2024

By Carlos F. Perucca

"Potassium is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production.Potash is extracted from buried ancient evaporites by underground or solution mining. This accounts for most of the potassium produced. Another important source is brine from landlocked water bodies, such as the Dead Sea, Salar de Atacama or Great Salt Lake.About 95% of potash produced worldwide is used in agriculture. The rest is found in several other industrial uses, including glass manufacturing, soaps, plastics and pharmaceuticals.Currently, three producers: IMC, PCS and Agrium operate 8 conventional and two solution mines in Saskatchewan, five of which run froth flotation circuits, two heavy media-flotation, two run forced crystallization and one natural crystallization.Potash in SaskatchewanPotash was discovered in Saskatchewan in the early 1940’s while drilling for oil. The deposits lie diagonally across the southern plains of Saskatchewan sloping southerly from a 1,000m depth at Saskatoon to more than 1,600 m depth at Belle Plaine and up to 3,000 m in depth in North Dakota. The known deposits are massive, accounting for more than 40% of the world’s known reserves."

Jan 1, 2003

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

It has been proven theoretically and experimentally that the use of 10 - 30 per cent DRI in blast furnace along with iron ore or sinter results in lower coke rate and higher productivity. However, to-date this remains unpractised on a regular basis mainly because of economic reasons. The DRI produced by several methods are expensive and difficult to store/handle in large quantities because of its reactive nature and thus DRI in blast furnace remains unacceptable.

Jan 1, 1999

By O. F. Ochonogor

Laser metal deposition (LMD) is an additive manufacturing technique whereby a stream of metal powder is consolidated by a focused laser beam on the surface of a substrate or engineering component. The interaction zone between the laser beam and powder particles is scanned superficially, generating tracks of deposited material. The tracks are overlapped in a deposition strategy in accordance with slices of a CAD model. Successive layers of material are built up to fabricate a near net shape part. In this work, the technique is used to fabricate metal matrix composites (MMCs) by using an elementally blended feedstock combining metal and ceramic powders in the melt pool, which melt and solidify to create the required morphology. Ti6Al4V + TiC MMCs were produced with 10, 20, and 30 vol.% reinforcing ceramic, and Zr + TiC MMCs were fabricated with 10, 20, and 30 vol.% TiC. The deposited thin walls were analysed using optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and indentation testing. In both systems, the analysis revealed the presence of partially melted TiC particles embedded in the metal matrix along with fine dendrites of re-solidified ceramic. The dendritic structures in the Ti-based composites were confirmed as TiC, whereas in the Zr-based composite the Zr metal reacts with theTiC to form ZrC, leaving Ti in solid solution. Both the MMCs show an increase in microhardness with increasing ceramic (carbide)content, reaching a peak HV0.1 value of 500 in the Zr- based MMC and HV0.1 of 550 in the Ti based MMC.

Jan 1, 2012

Implementation of an Energy Efficient Dry Grinding Technology into an Anglo-American Zinc Beneficiation Process

Sep 13, 2010

By O. N. Sikazwe

The Nchanga Cu-Co ore deposit of the Zambian Copperbelt, is hosted in Neoproterozoic siliciclastic-carbonate sedimentary rocks, and it consists of two orebodies: the Lower Orebody (shale) and the Upper Orebody (arkose). Refractory Cu ores present in the Upper Orebody comprise 150 Mt with average 0.87% Cu, and are characterized by inadequate recovery of copper by leaching. This materials characterization study, conducted on refractory ore samples from the Upper Orebody using optical microscopy, QEMSCAN®, and microprobe, has shown that copper occurs mainly in biotite, phlogopite, malachite, pseudomalachite and goethite. QEMSCAN® has quantified the abundance of each phase and total Cu deportment in each phase.

Jan 1, 2008

By AIME

DURING the happy and peaceful years between the Treaty of Versailles and the third New Deal, metallurgy became one of the most cosmopolitan of the sciences. Any metallurgist can name some twenty or thirty scientists whose work, in this country, in England, in Germany, or in France, Sweden, Italy, or Japan was as well known in other parts of the metal-producing and metal using world as it was locally, despite the fact that many of these men never left their native land. One of these metallurgical cosmopolites is Augustus Braun Kinzel, former Chairman of the Iron and Steel Division, A.I.M.E., and now a Director of the Institute. Gus Kinzel, however, is not only a cosmopolite by reputation; he is also a cosmopolite in fact. For many years he commuted at least twice a year between New York and the rest of the world; he is, therefore, not only an expert on the art and science of metallurgy but is equally expert in world travel and can expound with authority on the comparative quality and especially on the cuisine of the great prewar steamship lines; and being a true cosmopolite, he knows, as well as he knows the iron-chromium diagram, the best vintage years in the Gironde, Cote d'Or, and Saone-et-Loire departments in France and along the banks of the Moselle and Rhine in Germany.

Jan 1, 1946

By K. Burke, K. L. Myers, R. Espell

Barrick Goldstrike’s (Goldstrike) AA Heap Leach Pad is an HDPE lined facility used for gold recovery from low grade ores using conventional cyanide heap leach technology, operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA Leach Pad Facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada’s closure requirements. Traditional Nevada leach pad closure has involved rinsing to reduce cyanide concentration to an acceptable level, followed by reclamation. However, certain metals and compounds are not typically reduced by rinsing and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as Nevada, the fine-grained layer will rarely reach full saturation and the cover will be able to store water during precipitation and allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22 m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the re-contoured AA Heap Leach Pad was specifically designed to enhance the revegetation, reclamation, and sediment yield control aspects of the AA Heap Leach Pad closure, while resulting in a natural looking surface, compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for re-contouring and erosion control design.

Jan 1, 2001