Search Documents

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By G. L. Oldright

In an earlier series of 15 Reports of Investigations on Smelting in the Lead Blast Furnace, experimental data were given on the operations of a custom smelter, a smelter treating rich lead products, and a smelter treating highly zinciferous charges. Five "reports" were written on each of the three types of operation, which were later compared in a summary written for the Institute. Developments in each of these types of operation in lead smelting since the last of the above reports was written have continued and have followed modifications necessitated by changes in the nature of the products received for smelting. The sintering-blast furnace-smelting plants have improved their sintering operation .and have made "2-pass" sintering a more standard operation; the richer lead feeds are diluted when marginal precious metal ores are not available to prevent fusion of the sinter cakes and to permit air to contact the sulfides. Means have been devised to make it easier to remove metallic lead from the wind boxes, but no attempts have been observed to use the D & L somewhat as an ore hearth to make more metallic lead. Except in those cases where zinc-rich lead blast-furnace slags were to be retreated in a "slag-fuming furnace," the sintering and the blast-furnace operations were so carried out that a relatively "clean," lead-poor, final slag was discarded.

Jan 1, 1949

The treatment plant at Martha Mine was upgraded from a nominal throughput of 110tph (O.93mtpa) to 150tph (1.25mtpa) late 1999. Post-upgrade performance did not meet expectations when treating either the competent primary ore or the clay-rich oxide ore.   ò Plant throughput is constrained by milling capacity when treating the competent primary ore. This is not an issue at present as current plant feed is oxide ore from the top of the open-pit, but will become so in future years as the pit deepens. To counter this future threat, ball mill power has been restored to 1100kW through modifications to the drive train. The addition of a crushing circuit may also be necessary.   ò Plant throughput was originally constrained by thickener and leach/adsorption tank issues when treating the oxide are. Changes to plant equipment and operations has seen the removal of these constraints and throughput on this material is no longer a problem.   The most significant issue facing plant staff at present is the high silver grade and its impact on gold recovery. These high grades impact upon recovery through losses caused by insufficient leach and adsorption capacity. To counter this, the geology, mining, and milling teams are working together to blend the high grade silver zones with lower grade ores - this is seen to be the quickest and most cost effective way to deal with the issue. The plant design has also been evaluated with a view to modifying it to cope with the higher silver grades. The viability of these modifications will depend on cost and time (that is, the length of time to implement any modifications versus the length of time to mine out the high silver zones).

Jan 1, 2001

Experiments on High Efficiency Separation of Mixed Plastic Wastes by Vortex-Tube Separator

Sep 13, 2010

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By Steve Skelhorn, Dan Ifrim

"A tunnel project poses many challenges; the operation of the Tunnel Boring Machine (TBM) being one of them. Mechanized tunneling is known as a safe and effective alternative to other methods in terms of schedule and cost; however, efficiency can be severely affected by a bad TBM selection and qualification and employment of inexperienced operators. The success of a mechanized tunneling project involves a comprehensive and interdisciplinary consideration of all contributing factors such as TBM technical specification and selection, TBM design and procurement including ancillary equipment and tunnel linings. The tunnel equipment selection along with the operation can make or break the project. The objective of this paper is to address the importance of the skills and qualifications of the TBM crew with particularity to the TBM Operator. The study includes the Owner and Consultant involvement in the selection and pre-qualification of the TBM crew and specifically the TBM operator as well as the role of Contractor and TBM manufacturer in TBM operator training. This paper also analyzes the possibility of issuing a TBM operator certification, and discusses the benefits and significance of periodic training and certification programs. INTRODUCTION Training in the tunneling industry is not a new topic. The industry continues to evolve and become more complex with technology advances and expansion of mechanical tunnelling to mechanized shaft construction, large diameter drilling and mining industry applications. The need for professionals trained to operate mechanized tunnelling equipment is ever increasing, while there is a significant number of veterans who will be ageing out in the next 5 years. Consequently attracting young professional is a very important aspect of sustaining a qualified pool of professionals. For any given tunnel project, the owner and the engineer spend up to several years, studying the ground conditions during preliminary and final design. Post contract award the contractor spend additional months studying the ground again to develop the optimum means and methods for construction. All this time and money spent at the beginning of the project has the purpose of developing the optimum tunnel design, assessing the risk associated and implementing mitigation measures to reduce risks to acceptable levels. Following the tunnel design process, sophisticated TBMs are being specified and sourced to ensure the best tool for the job. The question raises here: Are there available experienced/trained professionals capable of operating these sophisticated machines?"

Jan 1, 2016

By P. J. Brereton-Stiles, M. S. Rennie, N. Singh

Ferroalloy producers are large-scale users of electrical energy, which in many countries is in short supply and increasingly expensive. Preheating and/or pre-reduction using natural gas, recycled furnace gas or coal fines have lowered the specific use of electricity, but the high energy concentration necessary for most reduction processes can be achieved only by the use of high electric currents. Most countries have insufficient electricity to supply the demands of industry and the domestic consumer, particularly during certain periods of the day and certain times of the year. The generation and distribution of electricity is a large-scale expensive business, which is financed and managed directly or indirectly by government bodies in most countries. Both economic and political imperatives determine how much electrical energy is made available to whom and at what price. In South Africa demand is set to outstrip supply within the next few years, and the local supplier Eskom has moved from a traditional demand tariff pricing structure to a time-of-use tariff pricing so as to limit peak demand usage. This will mean a substantial increase in electricity cost to those users unable or unwilling to reduce consumption during peak periods. The optimal use of the available electrical energy depends both on the process, the furnace size, the configuration and infrastructure of each plant and its cost structure. As the cost and availability of electricity is set to change dynamically, the management of the situation becomes a real time control and optimisation problem. This paper discusses some the process and operational constraints associated with low- or no-load conditions and how to manage the situation. Electrode management will be one of the key issues.

Jan 1, 2004

By Jake Gibson

"As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action toward decreasing greenhouse gas (GHG) and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel, accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery-powered ac systems and diesel-fired heaters, going noidle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, standalone mobile equipment HVAC.The history of GHGs and climate changeIn 1896, Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960s, Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Fig.1).In 1988, the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgment of a rising global annual temperature. The IPCC consists of more than 2,500 scientific and technical experts from more than 60 countries. Because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998, requiring all participating countries to reduce their GHG emissions by at least 5 percent from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States). In 2002, the Bush administration announced a policy for climate change relying on domestic, voluntary actions to reduce the "greenhouse gas intensity" of the United States economy by 18 percent by 2012. The U.S. still attends the Kyoto conference of parties (COPs) but does not participate in negotiations, as it is not bound by its terms."

Jan 1, 2014

By Phil N

A large number of experiments have been carried out by many workers on the recrystallization of deformed and subsequently annealed metals and alloys. Although observations on single crystals are of great importance in the study of the recrystallization textures of deformed and annealed metals, very little of this work deals with material in this form.Since, in deformed metals, the stress concentration is greatest at the grain boundaries and along the planes of slipping, it is to be expected that recrystallization will start in these regions. For example, in polycrystalline aluminium (1),:1: (2), copper (3), a-iron (4) and brass (5), (6), which had been deformed by cold-rolling, drawing, pressing or stretching and then annealed, the new grains first appeared in the boundaries of the original crystals, whilst in the case of cupronickel (7) and iron (8), recrystallization commenced along the slip planes of the deformed material. Deformed and annealed single crystals of aluminium (9) and cadmium (10) first start to recrystallize along slip planes and in deformation twins.The present work deals with the process of recrystallization of single crystals of lead after deformatjon by creep.Two factors enter into these experiments that were not met with in other work on this subject. Firstly, lead...

Jan 1, 1940

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

The Mount Angelo prospect outcrops as two copper rich gossans, the larger of which is 250 ft long and 70 ftwide. The mineralization is epigenetic and replaces part of a brecciated and disturbed lime tone and calcareou sediment sequence.Magnetic and self potential survey indicated a substantial body of sulphide mineralization, the top of which was approximately 100 ft below the surface.Diamond drilling confirmed this and established the presence of a mineral body of at least 500,000 tons, extending to a depth of 300 ft. Of the 500,000 tons, 200,000 ton are primary copper ore which a ays 2 per cent copper.This mineral body is not economic at present, but could become economic if copper mining is established elsewhere in the district...

Jan 1, 1966

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014