Search Documents

By C. Haberfield, J. Szymakowski

Recent studies by the authors into the behaviour of jointed rock masses using direct shear testing have confirmed that joint spacing has a significant effect on rock mass strength. The rock mass failure envelopes assessed from these tests have been compared to failure envelopes obtained using the Hoek-Brown GSI criterion. Good agreement between measured and estimated GSI strength envelopes where obtained when joint spacing was considered in the assessment of GSI. Les études récentes conduites par les auteurs sur le comportement des joints rocheux employant l'essai direct de cisaillement ont confirmé que l'espacement a un effet significatif sur la force de la masse rocheuse. Les enveloppes de ruptures obtenues pour ces essais ont été comparées à l'enveloppe de rupture obtenue en utilisant le critère GSI Hoek-Brown. Une bonne corrélation a été constatée entre les enveloppes obtenues expérimentalement et les enveloppes calculées par la méthode GSI quand l'espacement des joints a été pris en considération dans l'évaluation de GSI. Kuerzliche Untersuchungen der Autoren betreffs Reaktionen von gebrochenen Felsmassen zu direkter Scherkraft, bestaetigen, dass die Abstaende von Rissen einen deutlichen Einfluss auf den Widerstand der Felsmassen hat. Die Bruchbereiche der Felsmassen die von diesen Untersuchungen entwickelt wurden, wurden verglichen mit den Bruchbereichen, die man mit der Anwendund der Hoek-Brown GSI Formulierung erhaelt. Eine gute Uebereinstimmung zwischen gemessenen und errechneten GSI Festigkeitsbereichen wurde erzielt, wenn der Abstand der Risse in der Berechnung der GSI in Betracht gezogen wurde.

Jan 1, 2003

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By R. Jackman, D. Koningen, G. Wilcox

"Gowest Gold Ltd. is in the process of developing the Frankfield East gold deposit located along the largely undeveloped Pipestone fault northeast of Timmins, Ontario. In addition to resource development and environmental permitting work the company has had an ongoing program of metallurgical and engineering studies aimed at evaluating options for processing the Frankfield East ore. Mineralization at the Frankfield project contains arsenopyrite and pyrite as the major sulphide minerals. Bulk flotation of all sulphides results in extremely high gold recovery. However, the gold is almost entirely associated with the arsenopyrite fraction of the ore and is refractory in nature requiring preoxidation treatment. Selective flotation was investigated to recover a gold-arsenopyrite concentrate thereby reducing the mass which would be subjected to further gold processing. As part of this work, a pyrite concentrate low in arsenic content was also recovered that would be suitable as a source of sulphur for a smelter (or other pyrometallurgical facility). Production of separate arsenopyrite and pyrite concentrates is frequently examined but rarely adopted due to the distribution of gold between the two products or the inability to achieve adequate separation. Several flowsheet options were investigated in the study. The best results were achieved following a sequential flotation flowsheet. The flowsheet configuration was key to meeting the targets for the two products. In this paper, the various options investigated are reviewed and the results of the final flowsheet are presented. The overall plan by Gowest was to evaluate all process options to bring the Frankfield East deposit into production. The ability to effectively separate the arsenopyrite and pyrite components in the ore provides Gowest with added opportunities to pursue both short and long term production scenarios."

Jan 1, 2012

By Harry M. Conger

Thirty years ago, the U.S. gold mining industry was hanging on by its fingernails. Save for one great mine, the Homestake, most production was coming from copper smelters such as Kennecott and Magma. Even Homestake itself was under great pressure from rising costs and a fixed price for gold. The outlook was dim, to say the least. Today, as it has for most of the past decade, the American gold mining industry stands among the world leaders in production, and in the development of mining and mineral processing technology. What caused this dramatic change? Obviously, the freeing of the gold price was a major factor, as was the decline in South African production, but these events alone could not have created the U.S. strength we see today. It was technology, investment, and the determination of miners to build an entirely new industry that were the indispensable ingredients. The U.S. Bureau of Mines, with great foresight, had begun the research that led to heap leaching before the gold price began to rise, and Newmont had committed to build a small mill at Carlin, a move then considered quite risky. From that point, the U.S. gold mining industry was placed on lower-grade ores then being found in Nevada and elsewhere, but it was soon apparent that we would have to develop new technologies to deal with more refractory ores, carbonaceous as well as sulfide-bearing. This is now being done with considerable success. Despite its success, or perhaps because of it, the gold mining industry has come under pressure from various groups who characterize their activities as motivated by "public interest." The public interest they refer to properly include the health and safety workers and impacted communities, as well as protection of the environment, and with these concerns we miners have relatively little argument. In fact, we consider health, safety and the environment among our highest priorities, and not just because regulations may require us to do so. The argument, however, is not about the regulation of a viable mining industry, it is about a well-organized movement to attack and condemn mining in the media and to misrepresent its importance to the Nation and its willingness to accept responsible regulation. Once largely local or regional, the interest groups to which I refer are now quite large, national in scope, and even becoming international. This trend, taken together with finances raised from their dues and contributions, would make the interest groups formidable adversaries for mining, but their grip on the media enormously magnifies their influence. Unfortunately, it also makes possible the wide dissemination of incomplete, incorrect or slanted information. I am not here to "bash" the interest groups. On the whole, I believe that many of them have made positive contributions to society. As conservationists, however, I question their authority to make, or foster, decisions about which American industries and communities live and which die. To illustrate, I would like to present for your consideration the problem of cyanide, one of the issues over which the gold mining industry is most threatened. CYANIDE-POISON OR MIRACLE SOLVENT? Let me get this out of the way right up front: cyanide in most of its chemical forms is toxic. In some forms it is also listed as a carcinogen. These are adverse characteristics cyanide shares with a considerable number of industrial chemicals, including some that are widely used without the stringent regulations already in place for the mining uses of cyanide. In these uses, by the way, the risk to humans comes from direct ingestion of cyanide or cyanide-bearing solutions, or from the accidental acidification of solutions leading to release of hydrocyanic acid gas. That these risks are under control in mining can be seen from the fact that, in modern U.S. practice, there has never been a documented fatality attributed to cyanide! Because of its toxicity, cyanide cannot enter and be accumulated in the food chain. It can, however, be a threat to birds and animals that ingest cyanide-bearing solutions. Protection against this is, quite properly, a responsibility of individual mining operations, and considerable sums are spent each year to prevent or reduce bird and animal exposures. It should be evident, though, that many human activities, including highway traffic, windmills, use of pesticides and the like, result in bird and animal losses. Mining's use of cyanide, and the measures taken to protect birds and animals, should be considered in context. Cyanide must be kept out of surface streams and groundwater, and existing regulations mandate this. Any cyanide residues left in leach heaps, waste dumps and disused facilities must be eliminated, and we have proven technologies to do this now, just as we have means to detoxify tailings prior to disposal. The gold mining industry decries those rare instances when irresponsible operators fail to deal with contamination, and agrees that they should be held responsible. We do not agree, however, that the great majority of responsible companies should be punished, in advance, for accidents that have never happened. So much for the poison, what about the "miracle solvent?" Is that an overstatement? Well, consider the fact that gold has been called "noble" from earliest times, because it does not oxidize under atmospheric exposure, and that it appeared to the ancients to be utterly insoluble. Later generations of scientists did discover that it could be dissolved, but only by a combination of acids so potent that it became known as aqua Regia. Later still, it was found that chlorine would also dissolve gold, and attempts were made to base commercial processes on this, without a great deal of success. It remained

Jan 1, 1995

By D. A. Ainsworth

"The first known use of activated carbon dates back to the Ancient Egyptians who utilized its adsorbent properties for purifying oils and medicinal purposes. Centuries later, the early ocean going vessels stored drinking water in wooden barrels, the inside of which had been charred. (However, by modern definition the carbon used in these applications could not truly be described as activated.) By the early 19th century, both wood and bone charcoal was in large scale use for the decolorization and purification of cane sugar.However, it was not until the beginning of the First World War that the potential of activated carbon was really capitalized upon. The advent of gas warfare necessitated the development of suitable respiratory devices for personnel protection. Granular activated carbon was used to this end as, indeed, it still is today.By the late 1930's there was considerable industrial scale use of carbon for both gaseous and liquid phase application and new manufacturing processes had been developed to satisfy the needs of industry. During the 1939-1945 war, a further significant development took place - the production of more sophisticated chemically impregnated carbon for the removal of both war and nerve gases."

Jan 1, 1984

By Peter W. Kauffman

This Bureau of Mines publication is designed primarily to provide mine engineers and production-level mine managers with the following: 1. Information to assist them in making the decision to retreat mine and in selecting the best retreat mining technique for specific mining conditions. 2. Information on mine planning that will enable them to design mine layouts for safe and efficient retreat mining. 3. Information that will enable them to develop a section foreman's handbook. The manual has been organized to gradually increase in level of detail as the reader progresses from beginning to end. Individuals interested in an overview of retreat mining can confine themselves to the first few chapters. Those interested in mine planning, should read the middle chapters as well. Those interested in the development of a foreman's handbook should read the entire manual.

Jan 1, 1981

By G Eastwood, C Joyce, P Ryan, G M. Johnston

Over the years, predictive techniques for Acid Mine Drainage (AMD) and the natural processes affecting acid generation have received considerable attention. Less emphasis has been placed on the sampling strategy and the integration of testwork results with the geological data base. The sampling strategy employed and the development of a geological model to determine the spatial distribution and volume of acid producing material are often crucial for developing cost-effective containment and mitigation measures. The geological model provides a link between the occurrence, timing, destination and placement of mined waste rock. Careful and accurate interrogation of a comprehensive geological database provides this linkage. The AMD testwork program at Cadia in NSW has been designed to identify the temporal selective handling requirements that will be required during operation. Sampling involved collection of representative combinations of all waste rock types identified within an extensive geological database. These samples were subjected to static, kinetic and accelerated weathering predictive tests. Preliminary results have been used to construct a waste block model for the deposit that identifies the quantity and distribution of acid producing material. Integration of the block model with the mine scheduling determines when the material will be mined.

Jan 1, 1996

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014

By Reinhold Schnell, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e.,metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine. The findings of and lessons learned from this case study can be applied toother mine operations to improve safety, production, efficiency, and cost savings. Focus areas for the project included refined communications, operational practices and procedures, planning, designing, and data collection and analysis. This case study showed improved efficiency in communication and planning among the engineers, operations team, and contractor groups over the course of the project. An increased awareness of long-term plans and needs for the drills and blasters reduced or eliminated existing delays. Test blasts that implemented new drill and blast designs and updated operational practices and procedures were tested to streamline the process. Constraints regarding explosive product shipments, geological considerations, and a uniform powder factor provided the basis for new blast designs.

By S Vianna, K Caldwell, R Silva, T Olson, D Bell

Studies to enhance the FLSmidth forced air machine through changes in the design, showed important improvements through changes in the number of Rotor blades, stator designs, rotor air distribution and other designs features. The main outcomes from this study highlighted that increasing the number of rotor blades increased the selectivity while decreasing power requirements while stators with slots have better results in terms of recovery, flotation efficiency and selectivity than without slots.Also the rotor air distribution makes a difference in the design when comparing different distribution criteria whilst keeping all features of shape and number of blades etc constant. At the most efficient rotor air distribution design, copper recovery reached one of the highest values while keeping good selectivity. The possible explanation for that is the increase in the pump capacity indicated by the increase in the specific power.It was seen as significant that reduction in specific power for some designs tested compared with the then current standard design had an average of 30% less power consumption.As a result, FLSmidth was able to identify new designs that decreased power and improved recovery, as well as, identifying some designs that specifically improved fine and/or coarse particle recovery.CITATION:Silva, R, Caldwell, K, Bell, D, Olson, T and Vianna, S, 2013. FLSmidth flotation developments - Dorr Oliver machines, in Proceedings MetPlant 2013 , pp 413-430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By J. D. Steenkamp

Southern Africa has a history rich in the pyrometallurgical processing of ores. Two of the alloys produced are high-carbon ferromanganese (74?83 per cent Mn) and silicomanganese (59?67 per cent Mn and 14?31 per cent Si). The largest land-based manganese ore deposit in the world is based in the Northern Cape Province of South Africa. In 2010, 6.3 Mt of ore from the deposit was exported, mainly to China, Norway, Japan, and India, and an estimated 1.1 Mt beneficiated locally to produce manganese ferroalloys. In southern Africa the producers of manganese ferroalloys are Metalloys and Assmang, and of silicomanganese Transalloys, Mogale Alloys, and Match Corporation. Submerged arc furnace technology is utilized in the production of high-carbon ferromanganese (HCFeMn) and silicomanganese, applying the discard slag practice in both instances. The carbon content of HCFeMn is reduced using converter technology and that of SiMn using the Perrin process. Ninety per cent of the world?s manganese ferroalloys production is consumed by the steel industry. The consumption (and production) of manganese ferroalloys therefore closely follows worldwide steel production. From 2001 to 2010, the doubling of the worldwide production of manganese ferroalloys can be attributed to an increase in production capacity in Asia and Oceania, with the largest increase in the production of SiMn. Manganese ferroalloys produced in Asia and Oceania are mainly for the local market, with North America, Europe, Russia, and Turkey the major markets for alloys from southern Africa. The major challenges faced by the southern African manganese ferroalloy producers are increasing electricity tariffs and productivity of labour, which require a concerted effort by all parties involved to achieve a satisfactory solution. Keywords manganese ferroalloys, ferromanganese, silicomanganese, southern Africa, South Africa, manganese ore, high-carbon ferromanganese, refined ferromanganese, refined silicomanganese.

Aug 1, 2013

By Nicholas Macrae Steven

Abstract - The Shaba-type Luamata Cu-Co(-Ni) deposit (11°50_S, 24°28_E) is located in a tectonic slice of Katangan Roan Supergroup (Mines Group) sedimentary rocks, surrounded by younger Kundelungu Supergroup lithologies in the external fold and thrust belt of the Lufilian Arc. Luamata is a classic central African copper clearing in dense woodland, visible as a tonal botanical anomaly on Landsat imagery. Supergene Cu-Co mineralization (especially malachite and subordinate chalcocite, digenite, covellite, and copper and cobalt oxides) and, probably hypogene, bornite, and chalcopyrite are hosted by altered, but essentially unmetamorphosed, moderately dipping, dolostones and dolomitic shales. Alteration products include talcose dolomite, sericite rocks and intense silicification and brecciation. Friable yellow shale is best mineralized with cobalt (up to 0.43 wt%), whereas, highest copper grades occur in brecciated, silicified shale (up to 13.5 wt% CuO). Soil copper and cobalt contents are up to 2.2 and 0.6 wt%, respectively. A newly identified nickel zone (where soil contents exceed 0.1 wt% Ni) fringes the Cu-Co deposit. Polymictic, matrix-supported breccias with a calcareous matrix that underlie the Cu-Co deposit are interpreted to be fluidization breccias related to thrust tectonics and the emplacement of the Mines Group slice. Although small compared to the Kolwezi district Shaba deposits in the Democratic Republic of the Congo, Luamata exhibits all the classic features of an ore deposit type (with low calcite contents), whose high metal concentrations could potentially be very profitably exploited by low-cost opencast mining and hydrometallurgical recovery methods.

Jan 1, 2000

By C. O. Aksoy

There is a long history of coal production in Turkey with electric energy generated from power plants since the 1950s. However, the cost of power generation is high. Therefore, it has become necessary to find a means of decreasing production costs to become more competitive in a global market. This paper attempts to economically minimize the overall operating costs of a dragline-shovel-truck system applied at an open pit mine that has fed the Yatagan power plant since 1979, lowering the lignite production cost, and indirectly, the overall electricity generation unit cost. Systems currently in place, as a result of former optimization studies, are time-consuming and expensive to re-implement to comply with today’s very different geometric and economic conditions affecting mining operations. In such cases, rather than re-optimization, it is more viable to identify the parameters that affect the minimum unit cost, via a cost minimization study, allowing present mine equipment to be utilized more efficiently. Unit cost minimization analyses are subject to the capacity of the pool of mining equipment available, combined with the mining block geometry from pre-stripping onwards. In this overall unit cost minimization study, P&H shovels and CAT 777 trucks with capacities of 15 yd3 and 77 tons, respectively, were used in truck-shovel pre-stripping operations. A 65 yd3 Marion 8050 dragline was used to expose the overburden immediately over the coal seam. Pre-stripping bench heights varied from 8 m to 20 m and dragline bench heights from 20 m and 25 m were evaluated to minimize the unit cost of field operations. Total overburden extended to a depth of 60 m (35 m to 40 m for pre-stripping). Minimization analyses performed on the pre-stripping truck-shovel operation, prior to dragline operations, determined that the shovel bench height should be 15 m requiring a dragline bench height of 25 m.

Jan 1, 2005

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By D. E. Ng?andu

The experience of Mufulira concentrator, of the Zambia Consolidated Copper Mines Limited, with underground mine drainage water, which is used in milling operations is discussed. It is shown that the underground mine water has a deleterious effect on flotation performance. The adverse effect of the underground water was successfully negated by adding lime into the primary ball mills and increasing the pH of the slurry, from a ?natural? pH of 8 to the flotation pH of 10.5. Traditionally, the pH modifier, quicklime, had been added downstream of the milling. Changing the lime addition point further reduced lime consumption by 50%,?a key issue as lime accounted for over 60% of the Mufulira flotation reagent costs. The nature of the effect of the underground water at Mufulira, particularly the sensitivity of the flotation to the pH at which the milling was conducted, characterized galvanic interaction. A large-scale plant situation is presented in which the desired electro-chemical response in the flotation was achieved, by a deliberate manipulation of the milling environment. The experience provides practical testimony of a more fundamental role for the milling process, other than the mere physical preparation, i.e. size reduction and liberation, of mineral particles prior to flotation.

Jan 1, 2001

By S. Fuentes, J. Cáceres

"During the past fifteen years, mines utilizing the block caving method have improved performance and systematically reduced total mining costs.This paper describes improvements in mine design, mine planning, and mine management, including methods enabling the Chilean and international mining industry to ensure cost savings and productivity growth while using the block caving method. These improvements have encouraged the re-evaluation of underground operations at operating and closed open pits, and challenge surface mining applications as the only low-cost mining method. This paper describes a strategy to estimate the optimum open pit to underground transition time during the life of a mine. IntroductionDuring the last fifteen years, block caving mines have experienced huge changes in designs, planning and administration. These changes have permitted operators to drastically reduce costs, improve equipment productivity, and improve overall business performance. As a consequence of this situation, the block/panel caving mining system is challenging actual open pit operations to maximize the net present value (NPV)."

Jan 1, 2004

By D R. Peacor, J L. Mauk

Dioctahedral clay minerals in the volcanic-hosted Golden Cross epithermal Au deposit, New Zealand, have been investigated by petrography, X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy/analytical electron microscopy (TEM/AEM) to determine the nature of these minerals in a hydrothermal ore deposit. Heterogeneity in the distribution of dioctahedral clays is observed from the hand-specimen scale to the TEM scale, indicating that primary rock textures and fluid pathways (related to rock type, porosity/permeability and fluid/rock ratios), in addition to temperature, are important factors controlling the distribution. As the proportion of illite in mixed-layer illite/smectite (I/S) decreases, TEM observations show decreasing layer stacking order, parallelism of packets, and packet size, and increasing apparent porosity. AEM structural data show a corresponding decrease in AlIV, AlVI, and K+, and an increase in Si, Ca2+, and Fetotal. The observations of this study indicate that local dioctahedral clay mineral reaction progress is controlled mainly by permeability and structure, but that this is superimposed on a predictable, system-wide clay mineral distribution that is controlled by temperature and fluid/rock ratio.

Jan 1, 1999

By Michael R. Walsh, John H. Wright, Eivind B. Jensen

A tunnel boring machine (TBM) was designed and built at the Cold Regions Research and Engineering Laboratory in 1992 for use in Antarctica. The TBM system was tested at the South Pole where a 120-m long tunnel was bored to prove the concept. Modifications were made to the system resulting from this work. In 1999,boring of a 600-mutilidor began as part of the new South Pole Station. Tunneler hydraulics reliability problems prevented the completion of the tunnel before the end of the short construction season. This paper discusses the design and operation of the TBM, proposed solutions to the problems encountered, and current operations of the system.

Jan 1, 2001