Search Documents

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Richard A. Heckman

Destructive Thermal Technology (DTT) is used in the management of various waste streams. DTT includes Destructive Distillation, Pyrolysis and Classical Incineration. Recent work has more clearly defined the differences in these technologies based upon a more rigorous thermochemical approach. The U.S. Environmental Protection Agency (EPA) has chosen Classical Incineration as the Best Developed Available Technology (BDAT) for the management of hazardous organic wastes. Municipal Solid Wastes (MSW) and Sewage Sludges (SS) are also managed using Classical Incineration. Three environmental problems plague the use of Classical Incineration. Destructive Distillation, on the other hand, avoids these problems. It is an environmentally benign DTT for managing a wide variety of organic waste streams, including hazardous wastes. Thermochemical analysis of the available data on the performance of three types of DTT will be discussed.

Jan 1, 1994

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3-PbZrO3-Pb(Mg1/3Nb2/3)O3) system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densifieation by the normal sintering was slow even at high temperatures. When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.

Jan 1, 2003

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By V. I. Lakshmanan

Crown ethers are gaining importance in separation technology specifically for rare earth elements (REE, La to Lu plus Y) and precious metals (Au, Ag, Pt, Pd, Rh and Ir) due to their specific binding ability, metal complex stability and high extraction efficiency. The selectivity of crown ethers in extraction of these metals depends on different factors, including the cavity diameter and nature of a donor atom of the crown ether, size and charge of the metal ion, diluents and counter ion. Demand for strategic REE and precious metals are consistently increasing in the world while the separation of these metals is most challenging tasks. In this paper, the use of crown ethers in separation of REE and precious metals, reaction mechanisms and simplified process flowsheets will be elucidated. New reagents with high selectivity for the separation of these metals are further expected to produce high purity metals.

By Rodríguez M. Esperanza

The efficient performance of Pachuca tanks is strongly linked to the suspension of mineral particles, which results from the motion of the liquid caused by injected gas rising, in general, through a central draft tube. This study reports a computational investigation on the effect of operating and design parameters on the suspension of particles. By extending the classical 2-phase drift-flux model to compute the gas hold-up, the three-phase (water-air-particles) system was simulated as consisting of a variable-density liquid plus the solid particles. These two phases were treated as interpenetrated continua using an Eulerian approach to set a turbulent recirculating flow model in 2-D and transient state. The model predicted adequately the measured critical superficial air velocity, uc, needed for maintaining particle suspensions, in pulps with 10-50 wt% solids. Additionally, the model was used to investigate the operation of industrial size reactors, obtaining results that agree well with the general trends reported in the literature, and highlighting important differences with respect to laboratory-scale reactors.

Jan 1, 2009

By Mokka Rao, Asdrubal Serrano

"A mathematical model is developed which describes the movement of the minerals present where the vertical and angular velocities are related with the different operative parameters involved in the process of separation of silica from iron ore, which permit maximise the capacity of the spirals to obtain major productivity. The process is realised in two steps, of the rough dressing and other cleaning. Through the results obtained for chemical analysis of the final products of each spiral and the equation of movement of particles, it is proved the applicatibility and efficiency of mathematical model to operating parameters of the spiral. Moreover, it is determined though the recuperation of the final products of quality in the use spiral HC 1870 and HG 8/7. INTRODUCTIONThere is prospetive of increasing the production the iron ore in agreement with the demand of siderurgical proyects united with the external demand of quality 40 million tons per year. The Ferrominera de Orinoco Company is experimenting two types of modem spirals, Humprey (HC 1870) and Reichart (HG 8/7) which have limited capacity. For this reason this investigation designed a mathematical model with which larger units can be designed for increasing the capacity of the spiral."

Jan 1, 1999

By Jayagopal Uchil, M. Krishna, Shanta Sastcy

"Damping behaviour of aluminite particulate reinforced ZA-27 alloy metal matrix composites processed by compocasting method is studied. The weight percentage of particulate reinforcement is 0,1,2,3, and 4%. A dynamic mechanical· analyzer is used ·to measure the damping capacity and dynamic modulus at the natural frequency of the specimen over a temperature range of 30°C to 300 °C both in the heating and cooling cycle. The damping capacity of the material is found to increase with increase in temperature and weight percentage of aluminite reinforcement although this is accompanied by a decrease in dyliamic modulus.The damping capacity and dynamic young's modulus exhibit a sharp decrease in their values around 300 °C a8 ZA-27 alloy undergoes a first order phase transition in this region which is confirmed by Differential scanning calorimetric studies. Several damping mechanisms have been evaluated theoretically for the material under study. The damping capacity at low temperatures is attributed primarily to coefficient of thermal expansion mismatch induced dislocations and high intrinsic damping of the matrix. At higher temperatures the damping capacity is attributed to ZA-27/aluminite interface, phase transformations and thermoelastic damping.IntroductionMetal matrix composites. (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and lightweight [1-5]. At present, the usage of ceramic particles as reinforcement in MMCs has attracted considerable interest from scientists and engineers. The MMCs show substantially improved elastic modulus, strength, stiffiless, and tribological properties with low coefficient of thermal expansion compared with the unreinforced matrix material."

Jan 1, 2000

By Charles H. Bucknam

A gold sampling optimization study was carried out in support of open pit gold mining operations for the Newmont Gold Company Bootstrap-Capstone deposits in Northeastern Nevada. Six bulk samples were tested using fire refining techniques at field particle size, to determine coarse particle heterogeneity of the ores, and by gravity .concentration methods at 10 mesh particle size, to observe any particulate gold liberation. An overall sampling model is presented for the deposit based on the pooled test information, to reconcile the results of coarse particle heterogeneity testing and the fine particle 'liberation testing. The sampling model is used to recommend procedures to control the variability of gold grade estimation due to the fundamental error (nugget effect) during sampling, sample preparation and assaying of the ores and other fundamental variances. The technique of simplified quantitative risk analysis (SQRA) is used to provide an economic justification for implementation of. recommended improvements to field sampling practices.

Jan 1, 1999

By Fujio Ishii

The deoxidation of liquid nickel and nickel binary alloys with silicon has been determined at temperatures between 1500°C and 1650°C using quartz crucibles in order to investigate the deoxidation of nickel based alloys. The equilibrium constant of the deoxidation reaction in liquid nickel and the effects of the different alloying elements such as chromium, molybdenum, tungsten, iron, cobalt and coppcr on the activity coefficient of oxygen in liquid nickel have been established.

Jan 1, 1993

By Anish Kumar

Keywords: Ultrasonic velocity, Poisson?s ratio, Elastic constants A new correlation has been established between two independent elastic properties, ultrasonic shear wave velocity and Poisson?s ratio, in a wide variety of isotropic solid materials, such as pure metals, ceramics, polymers and intermetallics. It has been shown for the first time that Poisson?s ratio decreases with increase in elastic moduli, E & G and ultrasonic velocities. This new correlation between two independent elastic constants may lead to the reduction in independent elastic constants for isotropic solid materials from two to one, at least for a given alloy system with different microstructural conditions.

Jan 1, 2005

By Niloy K. Nath

Two layer sintering by charging green sinter mix with normal coke rate in the upper layer and reduced coke rate in the lower layer, can substantially reduce the coke rate and also improve the sinter quality by producing more uniform thermal profile through out the bed height. The two-layer sintering process have been analyzed by numerical simulation of the process by a detailed CFD based model, considering all the important phenomena like gas-solid reaction, melting and solidification, flow through porous bed, heat and mass transfer etc. Optimization techniques like genetic algorithm, differential evolution is then applied to evaluate the optimum coke rate in the two layers of the bed to produce the ideal thermal profile and melting fraction in the sinter bed for optimum sinter quality. Through this optimization method both high quality sinter with minimum return fines can be achieved along with reduced coke rate. Application of a genetic algorithm for this type of process optimization has several advantages over the traditional optimization techniques since it can identify global optimum condition and perform multi-objective optimization much easily for complex industrial process like iron ore sintering. Keywords: Two-layer Sintering, Iron Ore Sinter Quality, Ergun's Equation, Gas-solid reaction, Melting Fraction, Multi Objective Optimization, Pareto Set, Genetic Algorithm

Jan 1, 2003

By Willem P. C. Duyvesteyn

A novel hydrometallurgical process for Escondida copper concentrates has been developed by The Minerals Laboratory of BHP. The Escondida Process consists of concentrate leaching, solution purification, electrowinning and residue flotation. Part of the copper will be sold as high grade concentrate and part as high purity SX-EW copper. Contrary to previous efforts for the development of a hydrometallurgical process for copper concentrates, this patented process does not advocate the total dissolution of copper. It only aims for the copper that is readily soluble in a mildly oxidizing environment with an ammoniacal or acidic lixiviant. Both lixiviants were studied, but ammonia was preferred because of fast kinetics at ambient temperatures and pressures. By controlling the oxidation potential, the formation of sulfate ions and, consequently, of an ammonium sulfate byproduct, is precluded. These mild leaching conditions also prevent the dissolution of unwanted impurities and result in the production of ultra-high purity electrowon copper. Solution purification is carried out by solvent extraction with LIX-54. The very high loading capacity of this organic results in a compact SX circuit, consisting of two loading, one scrubbing, and one stripping stage. As the organic is selective for simple copper ions, the copper amine complex is broken down and free ammonia is regenerated and recycled for leaching. High purity copper cathodes are produced in a conventional sulfuric acid based electrowinning system. One scrubbing step is needed to separate the ammoniacal circuit from the acid circuit. Limiting copper dissolution to less than 50% also provides an opportunity to produce high grade concentrates by residue flotation. Copper recoveries in excess of 98% with precious metal values reporting to the final concentrate can readily be obtained. Complete breakdown of the copper mineral- pyrite middlings results in a final concentrate grade that can be even higher than the original feed material. The Escondida Process also provides an opportunity to accept lower grade copper concentrates producing improved copper recoveries in the mill and yet high quality concentrates for marketing. The Paul E. Queoeau International

Jan 1, 1993

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center operated a batch pilot plant to demonstrate high-temperature cyanide leaching for recovering platinum group metals (PGM) from automobile catalysts. Approximately 1,600 kg of used pellet, monolith, and metal support catalyst containing 1,680 g (54 tr oz) of PGM were processed. Forty-five-kilogram batches of used catalyst were leached with sodium cyanide solution at 160° C for 1 h under basic conditions in a countercurrent processing sequence to dissolve the PGM. Extractions from the used pellet catalyst ranged from 94 to 95 pct for Pd, 95 to 97 pct for Pt, and 64 to 81 pct for Rh. Extractions from the used monolith catalyst ranged from 7B to BB pct for Pd, 75 to 90 pct for Pt, and 43 to 71 pct for Rh. Heating the pregnant leach solutions to 275' C for 4 h destroyed the PGM-cyanide complexes, resulting in over 99.7 pct of the PGM precipitating from solution. The PGM precipitate was predominantly a powder metallic concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed cyanide to less than 0.2 mg/L. Both the pellet and monolith residues were evaluated for disposal using the EPA Toxicity Characteristic Leaching Procedure.

Jan 1, 1995

By Zhihe Dou, Yan Li, Qiuyue Zhao, Guozhi Lv, Yan Liu, Hongliang Zhao

"Abstract: How to reduce carbon dioxide emissions has become a vexing problem, meanwhile, there exist high energy consumption and low efficiency problems in the existing CO2 capture and storage technologies. For CO2 comprehensive Utilization, this paper researches a new technology of absorbing the CO2 emission with high alkaline calcium or high alkaline wastewater sludge mineralization of calcium and invent a core device for multi-level jet carbonation. The industrial test has been carried out in China Xinyu slag Engineering Co., Ltd. The wastewater flow is 150m3/h in the pilot scale. The prepared calcium carbonate has a whiteness greater than 90%, particle size less than 150nm. The mineralization of aluminum exhaust with waste carbide indicates that the CO2 absorption rate is greater than 99.0%, CO2 concentration in the exhaust gas is lower than 0.08%, the purity of mineralized calcium carbonate is greater than 99.0% and particle size is less than 100 nm.InstructionAccording to the statistic data from IEA (2009), the carbon dioxide discharge from fossil fuel consumption in China has exceeded it in the US by the year of 2007, China, has become the largest emitter of carbon dioxide all over the world. Meanwhile, the economic scale is still on an increasing trend in the next 50-100 years, leading to a continuous increment in carbon dioxide discharge. According to the international energy agency forecasts, the energy-relative CO2 discharge in China will rise to 11,615 million tons, 91.3% higher than it in 2007. In the year of 2012, the CO2 gross discharge has reached 10,000 million tons, obviously higher than the predicted value. It is a tremendous task to reduce the emission. Non-ferrous metals industry is one of the largest emitters of carbon dioxide among the industrial circle, the whole industry might discharge a huge amount of carbon dioxide (over 600 million tons), in which the electrolytic aluminum industry is the largest energy consuming industry and CO2 emitter. At present, the CO2 discharge has focused by the whole world due to the environmental problems it causes; meanwhile, supplement of new carbon source is needed due to the exhausting oil and coal resources, so that various countries in the world are attaching importance of the recycle and purification of CO2. Many countries are studying on the cyclic utilization of carbon dioxide. Gas CO2 is mainly applied in chemical, pharmaceutical raw materials, beverage filling agent, refrigerant, inert medium, solvents, pressure source, the welding protective gas, antioxidant and fire extinguishing agent, etc. Solid CO2 is mainly applied in penicillin production, fish, cream, ice cream and other food storage and transportation at low temperature, etc. nowadays, such methods as absorption method, membrane separation, adsorption, etc. are widely used to recycle CO2, with such problems as high investment cost and technical constraints etc."

Jan 1, 2014

By Peter Woodall, Paul Telford, Pengfu Tan

"Arsenic enters the Mount Isa copper circuit in the form of arsenic rich minerals in concentrates from both the Mount Isa and Ernest Henry copper mines. Arsenic is a volatile metal, and will partition in the copper smelter between smelter off gases, slag and anode. Most of the volatile arsenic will report to Isasmelt Electrostatic Precipitator (ESP) or Waste Heat Boiler dusts where it will form a re-circulating load within the smelter. ESP dust is produced at a rate of 15,000 - 20,000 t/y and is currently removed from the precipitator and leached in the new ESP Dust Recovery Plant to separate copper and arsenic from the ESP dust. This paper describes the laboratory test works of ESP dust leaching, neutralisation and cementation processes. The planttrial, commissioning and operation have been presented as well.1. IntroductionThe flue dusts generated in the process of copper smelting contain appreciable amounts of copper and other valuable metals including precious metals. These flue dusts also contain appreciable amounts of arsenic trioxide where arsenic occurs in the ore body. The copper smelters processing concentrates generate residuals, such as ESP dust, containing arsenic trioxide. ESP dust contains impurities such as arsenic and bismuth which are harmful to the copper refining process if they report to anode. These impurities are fumed off in the smelting process and report to the dust as arsenic and bismuth oxides.The content of arsenic in the feed of Mount Isa copper smelter is about 0.1 % to 0.4%. Arsenic is a volatile metal, and will partition in the copper smelter between off gases and anode. Most of the volatile arsenic reports to Electrostatic Precipitator (ESP) and Waste Heat Boiler dusts where it will form a re-circulating load within Mount Isa Copper Smelter. Unless arsenic is bled from the smelter circuit, it will build up to a point where both anode quality and smelter hygiene are adversely impacted."

Jan 1, 2011

By Barry J. Welch

The production of primary aluminium can potentially lead to metal that, with minimum treatment, meets a high purity standard. Smelters that can achieve a significant proportion of their production in this manner have a competitive edge which is of growing importance as the use grows for such items as compact discs and the like. Superimposed on the desire to produce high quality metal are stringent environmental requirements that the industry must adhere to. The environmental 'legislation focuses on fluoride emissions and the approach adopted is towards a zero waste management philosophy. The fluoride recycling process does, however, result in volatile impurities being captured and recycled to the cell. Aluminium has an extremely high reduction potential and this results in a significant proportion of the recycled impurities being reduced at the electrolyte metal interface and thus contaminating the metal. This paper reviews sources of impurities and the impact of the operating procedures adopted on metal treatment.

Jan 1, 1996

By E. Gutierrez-Miravete

A computational method for the simulation of mold filling processes is described. The method is based on the representation of the flowing or deforming medium as a collection of mutually interacting parcels of material. Instantaneous positions of individual material parcels are calculated by numerical integration of the dynamic equations, subject to appropriate initial and boundary conditions. So far, the method has been used to produce qualitative simulations of some flowing and deforming systems encountered in mold filling technology, and our findings are summarized herein. In all cases, individual material particle motions can be followed in detail, allowing critical examination of potentially problematic mold design features.

Jan 1, 1992

By Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Garlic peel was used as the raw material to synthesize the biosorbent for the selective recovery of precious metals from the acid chloride solution. Garlic peel is rich in carboxyl-, amino- and thiol-groups, has the potential of exhibiting high affinity to Au(III) when appropriate chemical modification process was employed. Here in the present study, the biosorbent was prepared by cross-linking garlic peel particles with concentrated sulfuric acid. Adsorption tests for mixing different metal ions such as Au(III), Fe(III), Cu(II), Ni(II) and Zn(II) from various concentrations of hydrochloric acid media indicated that Au(III) was selectively adsorbed on the cross-linked garlic peel gel over the other coexisting base metal ions investigated. The crosslinking mechanism and selective adsorption of Au(III) were also investigated briefly.IntroductionPrecious metals are quite popularly applied in the modern industries such as jewelry, electronics and electrical devices, catalysts in chemical industry, etc. While their high values, limited deposit and quite large demand in industry makes its recovery from the industrial wastes, typically e-wastes, quite necessary. Actually, many techniques have been developed to recycle and recover the precious metals from various industrial wastes effectively in last decades, but the cleaning and ecofriendly processes are still seriously scarce [1]. Taking into account of the typical recovery processes using cyanide lixiviant in the alkaline media, or aqua regia, followed by the further recovery process using activated carbon adsorption or cementation with zinc, iron or aluminum plate or powder, though they both are quite effective recovery processes, if considering the special requirements on safety and ecofriendliness for the modern hydrometallurgical processes, various improved or novel extraction processes are greatly demanded [2]. Recently, the biosorption technology applied to the recover precious metals in the hydrometallurgical process has become a concern [3,4]. Inoue’s research group made great progress in the recovery of precious metals such as gold, palladium and platinum from the e-wastes such as spent mobile phone by using biosorption from the hydrochloric acid media [5,6]. This new hydrometallurgical process exhibits the prominent advantages of being cost-effective for its short process, easy operation and near-zero emission. In the above recycling process for e-wastes treatment, the preparation of biosorbents is the key and backbone of the whole recovery process. For this purpose, they developed a series of suitable sorbents for precious metals recovery by using the tanning-based or cellulose-based biomass such as persimmon peel, grape peel, orange juicing residue, waste cotton, waste paper through the crosslinking process with concentrated sulfuric acid and relative chemical modification processes [7-10]. In the present study, we also applied this technique to prepare the biosorbent of precious metal uptaking by using garlic peels as the raw materials, and investigated the adsorption properties of such-obtained gel in the hydrochloric acid media."

Jan 1, 2012

By Niels Verbaan

NioCorp is developing the niobium/scandium/titanium Elk Creek carbonatite deposit. The probable reserve announced by the company in 2017 indicated significant niobium (0.79% Nb2O5), titanium (2.81% TiO2), and scandium (71 g/t), and is composed predominantly of calcite, dolomite, and ankerite. Niobium is mostly (80%) contained in pyrochlore with the balance in various Fe-Nb-Ti oxides, which also host most of the titanium. Scandium is primarily deported in dolomite, with lesser quantities in pyrochlore and biotite. The process flowsheet recovers separate niobium, titanium, and scandium products. Scandium is extracted from whole ore hydrochloric acid leach solutions using solvent extraction and is further refined through a re-leach and precipitation process. Scandium leach residues are treated in a sulphuric acid sulphation process to recover separate niobium and titanium precipitates as well as to solubilize the remaining scandium. Both hydrochloric acid and sulphuric acid reagents are recycled within the flowsheet. This paper will discuss key bench and pilot test results of the niobium extraction and recovery circuits and will present a conceptual flowsheet developed by the project team for NioCorp at SGS Minerals.